MODIFICATIONS: A ORIGINAL ISSUE Matl Recom'd

Item Drawing No. Description Material ** ASTM *** Qty

Code Spare
1 TLKW/4250/KT/GA230077 - TRANSMISSION UNIT SEE BELOW - 1 X
1.1 K-004-3068 ASSY MEMBRANE UNIT ASSY. STANDARD MATERIAL '0' TYPE + XYLAN COATED MEMB. - 2 X
1.2 T7730-4250-1582 0285 SPACER CARBON OR CARBON-MANGANESE STEEL WITH MIN. YIELD STRENGTH 260 Mpa ASTM A350-07LF3 1
NOTE:
1.3 FT418 0225 GAGGING BOLT SET ISO GRADE 12.9 ASTM A574 / A574M 1
FITTED BOLT ENDS, PART OF REF 1.1 TO BE PAINTED YELLOW
2 K-004-3069 0285 MOTOR HUB CARBON OR CARBON-MANGANESE STEEL WITH MIN. YIELD STRENGTH 260 Mpa ASTM A350-07LF3 1
AND A NOTE ATTACHED INSTRUCTING CLIENT:-
3 K-004-3070 0285 FAN HUB CARBON OR CARBON-MANGANESE STEEL WITH MIN. YIELD STRENGTH 260 Mpa ASTM A350-07LF3 1
BOLTS PAINTED YELLOW MUST NOT BE REMOVED UNDER ANY
4 FT405 0225 HUB BOLT SET ISO GRADE 12.9 ASTM A574 / A574M 2 X
CIRCUMSTANCES.
IOM-TLKS FITTING AND MAINTENANCE INSTRUCTIONS.
GAGGING BOLTS ARE TO BE PAINTED RED AND A NOTE JOHN CRANE RESERVES THE RIGHTS TO SUBSTITUTE THE SUPPLY OF ITEMS LISTED ON BILL OF MATERIAL IN THE SPECIFIED MATERIAL BASED ON JOHN CRANE
ATTACHED INSTRUCTING THE CLIENT THE IMPORTANCE ** INTERNAL MATERIAL SUBSTITUTION POLICY WITHOUT PRIOR NOTIFICATION.

OF REMOVAL PRIOR TO TIGHTENING OF STRIPPER BOLTS. *** ASTM MATERIAL CODES ARE APPROXIMATELY EQUIVALENT BY MATERIAL CONTENT

GAGGING BOLTS MAY BE USED TO FIT AND REMOVE

TRANSMISSION UNIT ASSEMBLY. FIT BOLTS REF 1.3 AND
COMPRESS EACH MEMBRANE PACK BY EQUAL AMOUNTS
UNTILL DIMENSION ## IS NOT LESS 16.1 mm
DETAIL VIEW OF 703
MIN. COMPRESSION GAP
212 300 DBSE 191
4 HOLES DRILL & TAP 4 HOLES DRILL & TAP
1 M8 THRO'
M8 THRO'
EQUISPACED EQUISPACED
ON 351 PCD 1.1 1.2 1.1 ON 351 PCD 3
## 2 (JACKING HOLES)
1.3 (JACKING HOLES)

+0.031
40 0 +0.031
45 0
R 1
MAX. R 1
MAX.

O 188

O 220
+0.3
169.4 0

162 153.2

+0.3
0
O 314.5

O 314.5
O 371

O 371

185.4
155.7 Kg 140.3 Kg
+0.040
O 160 H7 0 MOTOR HUB
FAN HUB +0.040
O 175 H7 0
BORE & KEYWAY DETAILS
MOTOR (VFD) HUB BORE & KEYWAY DETAILS
ID FAN HUB

1.3

2 HOLES DRILL & TAP

M16 x 40 DEEP
4 18.887 4
EQUISPACED
DENOTES CENTRE OF GRAVITY ON 192 PCD
10.287 2 HOLES DRILL & TAP K- SELECT RECORD No.: 70521 / 2
(PULLER HOLES) COUPLING DUTY
MEM. PACK THKS 158.2 M16 x 40 DEEP
DUTY POWER SPEED TORQUE
TECHNICAL DATA :- SPACER EQUISPACED NORMAL 1780 KW 900 RPM 18886.4 N•M
ON 207 PCD CUSTOMER DATA
TOTAL WEIGHT 296 kg (ENGRAVE COMPLETE (PULLER HOLES) CUSTOMER: FFBL PO No FF14-152-03 ITEM
COUPLING CODE: CUSTOMER DRGS
MOMENT OF INERTIA 5.1578 kgm² TLKW/4250/KA/GA230077) JOHN CRANE REF GPN 90598805 QTY
IPROJECTS No: 322937-ME, DOR0133649
TORSIONAL STIFFNESS 6.19 MNm/radian PLANT ITEM No
COUPLING DATA END USER: FFBL
ANGULAR RESTORING MOMENT 1230 Nm/Degree RATING PEAK TORQUE APPLICATION END USER LOCATION KARACHI PAKISTHAN
DRIVEN EQUIPMENT ID FAN DRIVER EQUIPMENT MOTOR (VFD)
MAX. ANGULAR OFFSET 0.33 Degree (kW/1000rpm) CAPACITY (Nm) FACTOR
4250 81176 2.15 COUPLING DESIGNATION TLKW/4250/KA/GA230077
MAX. PARALLEL OFFSET ± 1.03 mm COUPLING DESCRIPTION
TIGHTENING TORQUE DATA TLKW-4250-W037-3000
MAX. AXIAL DISPLACEMENT ± 3.50 mm REF COMPONENT TORQUE (Nm) SCALE DATE
31 YYYY-MM-DD DRAWN CHECKED APPROVED DESIGN AUTH.
4 HUB BOLT 180 0.6:1 2019-06-13 NGS BGS - AE01
AXIAL FORCE @ MAX. AXIAL DISPLACEMENT 9500 N
FIRST ANGLE DRAWING No. SHEET No ISSUE
LATERAL CRITICAL SPEED >99000 rev/min PART OF 1.1 DRIVE BOLT NUT 785 PROJECTION

All intellectual property rights (including but not limited to copyright and design rights whether registered or unregistered) in relation to this drawing together with the information contained in this drawing (including but not limited to know-how and confidential information) is
proprietary to John Crane. Reproduction (whether in whole or in part) or use in any way whatsoever of this drawing or of any information contained therein is prohibited except with the prior written consent of John Crane. All rights in relation to this drawing are reserved. GA-230077 1 OF 1 A
A1