GR16 PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 52

SPEED CONTROL OF DC MOTOR USING

PULSE WIDTH MODULATION


A Project report submitted in partial fulfilment
of the requirements for the degree of B. Tech in Electrical Engineering
By

RUPESH KUMAR (EE2015/043)


MRITUNJOY RAY (EE2015/001)
SRIDEEP BASAK (EE2015/009)
TITAS RAY (EE2016/L02)
Under the supervision of

Mr. DIPANKAR SANTRA


ASSOCIATE PROFESSOR
Co-Guide

MR. SARBOJIT MUKHERJEE


ASSISTANT PROFESSOR
DEPARTMENT OF ELECTRICAL ENGINEERING

Department of Electrical Engineering


RCC INSTITUTE OF INFORMATION TECHNOLOGY
CANAL SOUTH ROAD, BELIAGHATA, KOLKATA – 700015, WEST BENGAL
Maulana Abul Kalam Azad University of Technology (MAKAUT)
© 2019
ACKNOWLEDGEMENT

It is my great fortune that I have got opportunity to carry out this project work under the
supervision of Mr. Dipankar Santra and Mr. Sarbojit Mukherjee in the Department of
Electrical Engineering, RCC Institute of Information Technology (RCCIIT), Canal South
Road, Beliaghata, Kolkata-700015, affiliated to Maulana Abul Kalam Azad University of
Technology (MAKAUT), West Bengal, India. I express my sincere thanks and deepest sense
of gratitude to my guide for his constant support, unparalleled guidance and limitless
encouragement.

I wish to convey my gratitude to Prof. (Dr.) Debasish Mondal, HOD, Department of


Electrical Engineering, RCCIIT and to the authority of RCCIIT for providing all kinds of
infrastructural facility towards the research work.

I would also like to convey my gratitude to all the faculty members and staffs of the
Department of Electrical Engineering, RCCIIT for their whole hearted cooperation to make
this work turn into reality.

Full Signature of Students

Place:
Date:
CERTIFICATE
To whom it may concern

This is to certify that the project work entitled SPEED CONTROL OF DC MOTOR USING
PULSE WIDTH MODULATION is the bonafide work carried out by Rupesh Kumar
,Mritunjoy Ray ,Srideep Basak ,Titas Ray a student of B.Tech in the Dept. of Electrical
Engineering, RCC Institute of Information Technology (RCCIIT), Canal South Road,
Beliaghata, Kolkata-700015, affiliated to Maulana Abul Kalam Azad University of
Technology (MAKAUT), West Bengal, India, during the academic year 2018-19, in partial
fulfillment of the requirements for the degree of Bachelor of Technology in Electrical
Engineering and that this project has not submitted previously for the award of any other
degree, diploma and fellowship.

_____________________ ________________________

Signature of the Guide Signature of the HOD


Name: DIPANKAR SANTRA Name: Dr. DEBASISH MONDAL
Designation: ASSOCIATE PROFESSOR Designation: ASSOCIATE
PROFESSOR & HOD

___________________________ ______________________
Signature of the Co-Guide Signature of the External Examiner
Name: SARBOJIT MUKHERJEE Name:
Designation: ASSISTANT PROFESSOR Designation:
TABLE OF CONTENTS:

List of Figures i
Abstract iii

1. INTRODUCTION 1
2. DC MOTOR 2
2.1. INTRODUCTION TO SPEED CONTROL 2
2.2. CLASSIFICATION OF DC MOTORS 2
2.3. SPEED CONTROL METHODS 4
2.3.1. FLUX CONTROL METHOD 4
2.3.2. ARMATURE AND RHEOSTAT CONTROL METHOD 5
2.3.3. VOLTAGE CONTROL METHOD 7
2.3.3.1. MULTIPLE CONTROL VOLTAGE 7
2.3.3.2. WARD LEONARD SYSTEM 7
2.3.4. PWM TECHNIQUE 9
3. PWM TECHNIQUE 10
4. DC MOTOR SPEED CONTROL USING PWM METHOD 12
4.1. PRINCIPLE 12
4.2. METHODS 14
4.2.1. ANALOGUE METHOD 14
4.2.2. DIGITAL METHOD 15
4.2.3. PWM GENERATOR CHIP 15
5. SOLDERING 16
5.1. SOLDERING IRON 16
5.2. SOLDERING STATION 16
5.3. SOLDERING IRON TIPS 16
5.4. BRASS OR CONVENTIONAL SPONGE 17
5.5. SOLDERING IRON STAND 17
5.6. SOLDER 17
6. BLOCK DIAGRAM 18
6.1. BLOCK DIAGRAM DESCRIPTION 19
6.1.1. POWER SUPPLY 19
6.1.2. ICC 555 TIMER 20
6.1.2.1. PIN DIAGRAM OF IC 555 TIMER 21
6.1.2.2. 555 TIMER WORKING 22
6.1.3. TRANSISTOR 23
6.1.3.1. APPLICATION 24
6.1.4. DC MOTOR 24
6.1.5. POTENTIOMETER 25
7. COMPONENTS 26
7.1. COMPONENTS REQUIRED FOR SPEED CONTROL 26
7.2. COMPONENT LIST OF 12V POWER SUPPLY 26
8. CIRCUIT DIAGRAM 27
8.1. CIRCUIT DIAGRAM FOR SPEED CONTROL 27
8.1.1. WORKING OF THE CIRCUIT 28
8.2. CIRCUIT DIAGRAM FOR 12V POWER SUPPLY 29
8.2.1. WORKING OF THE CIRCUIT 29
9. HARDWARE MODEL 33
10.RESULT AND DISCUSSION 34
11.CONCLUSION 37
12.FUTURE SCOPE 38

APPENDIX A:
A.1. SPECIFICATIONS OF HARDWARE COMPONENTS 39

REFERENCES 42
List of Figures:

Figure Page No.

1. Types of Motor 2-3


2. Flux Control Method 5
3. Armature or rheostat Control Method 5
4. Speed vs Armature Current Graph 6
5. Structural Arrangement of Ward Leonard System 8
6. 5V Pulses With 0% through 100% duty cycle 10
7. Simple Speed Controller 11
8. Pulse Width Modulation Waveform 13-14
9. Block Diagram of an Analogue PWM Generator 14
10. Block Diagram 18
11. 12V Power Supply 19
12. Pin Diagram of IC555 Timer 21
13. IC555 Timer 23
14. Darlington Pair npn Transistor 23
15. TIP122 24
16. 12 Volt DC Motor 25
17. Potentiometer 25
18. Circuit Diagram for Speed Control 27
19. Circuit Diagram for 12 V Supply 29
20. Full Wave Bridge Rectifier with I/p and O/p Waveform 31
21. 12V Supply Circuit (Hardware) 33
22. Circuit of Speed Control (Hardware) 33
23. Complete Circuit (Hardware) 33

Page | i
24. Pulse at Different Duty Cycle 35
25. Pulse at Different Frequencies 35
26. Motor Speed and Voltage at Different PWM Frequency 36
27. Motor Speed and Voltage at Different Duty Cycle 36

Page | ii
ABSTRACT:

In Industry DC motor is widely uses for speed control and load characteristics, it’s easy
controllability provide effective and precise output. So, application of DC motor is large for
commercial purpose. Speed control of DC motor is very crucial in application where required
speed is precision and correcting signal representing and to operate motor at constant speed ,so
we used PWM method which are fulfil all requirements to speed control of DC motor.PWM
based speed control system consists of electronic components (integrated circuit ,Potentiometer
etc).In this Project 555 timer (NE55P) is being operated in astable mode, which produce a
continuous HIGH and LOW pulses. The 555 Timer is capable of generating PWM signal when
set up in an astable mode. In this mode, the 555 IC can be used as a pulse width modulator with
a few small adjustments to the circuit. The frequency of operation of the circuit is provided by
the passive parameters of resistances and capacitors attached to it. The speed control of
DC motor is important in applications where precision and protection are of essence. The
variable speed drives, till a couple of decades back, had various limitations, such as poor
efficiencies, larger space, lower speeds, etc., However, the advent power electronic devices
such as power MOSFETs, IGBTs etc., and today we have variable speed drive systems which
are not only in the smaller in size but also very efficient, highly reliable and meeting all the
stringent demands of various industries of modern era. Direct currents (DC) motors have been
used in variable speed drives for a long time. The versatile characteristics of dc motors can
provide high starting torques which is required for traction drives. Control over a wide speed
range, both below and above the rated speed can be very easily achieved. The methods of speed
control are simpler and less expensive than those of alternating current motors.

There are different techniques available for the speed control of DC motors. The phase control
method is widely adopted in which ac to dc converters are used to supply the dc motors, but
has certain limitations mainly it generates harmonics on the power line and it also has poor p.f.
when operated at lower speeds. The second method is pwm technique, which has got better
advantages over the phase control.

In order to have better open loop speed control as demand varies frequently like in traction
system and many operations in industry must be control manually, PWM is most efficient and

Page | iii
cheap speed control method for dc drives. By varying resistor pot only, we can control the
speed of motor states that simple and easy method.

Page | iv
1. INTRODUCTION:

In this project, I will show How Speed Control of DC Motor can be implemented using 555
timer and Pulse Width Modulation (PWM). Most of the industrial process requires to be run
on the certain parameters where speed of the drive is concerned. The electric drive systems
used in many industrial applications require higher performance, reliability, variable speed due
to its ease of controllability. The speed control of DC motor is important in applications where
precision and protection are of essence. Purpose of a motor speed controller is to take a signal
representing the required speed and to drive a motor at that speed. In this project controller
presented uses the pulse width modulation (PWM) technique for speed control of DC motor.
We use DC Motors in many systems in our day to day life. For example, CPU fans, fume
extinguishers, toy cars etc. are all DC Motors which are operated by DC power supply. Most
of the times we will have to adjust the speed of the motors as per our requirement. A CPU Fan
for example, must be operated at high speed when the CPU is preforming heavy tasks like
games or video editing. But for normal usage like editing documents, the speed of the fan can
be reduced. Although some systems have an automatic adjustment system for fan speed, not
all systems possess this functionality. So, we will have to adjust the speed of the DC Motor
ourselves occasionally. The circuit is used to control speed of DC motor by using PWM
technique. Series Variable Speed DC Motor Controller 12V uses a 555 timer IC as a PWM
pulse generator to regulate the motor speed DC12 Volt. IC 555 is the popular Timer Chip used
to make timer circuits. In the Astable mode (AMV), the IC works as a free running
multivibrator. The output turns high and low continuously to give pulsating output as an
oscillator.

Page | 1
2. DC MOTOR

2.1. INTRODUCTION TO SPEED CONTROL:

Speed control means intentional change of drive speed to a value required for performing the
specific work process. This concept of speed control or adjustment should not be taken to
include the natural change in speed which occurs due to change in the load on the shaft.
Any given piece of industrial equipment may have its speed change or Adjusted mechanically
by means of stepped pulleys, sets of change gears, variable speed friction clutch mechanism
and other mechanical devices. Historically it is proved to be the first step in transition from
nonadjustable speed to adjustable speed drive. The electrical speed control has many
economical as well as engineering advantages over mechanical speed control
The nature of the speed control requirement for an industrial drive depends upon its type. Some
drives may require continues variation of speed for the whole of the range from zero to full
speed or over a portion of this range, while the others may require two or more fixed speeds

2.2. CLASSIFICATION OF DC MOTORS:

DC motors are classified into three types depending upon the way their field windings are
excited. Field windings connections for the three types Of DC motors have been shown in fig.1.

Page | 2
FIGURE 1

Page | 3
2.3. SPEED CONTROL METHODS

SPEED CONTROL METHOD OF DC MOTOR:


➢ Armature or Rheostatic control method.
➢ Flux control method. It is seen that speed of the motor is inversely proportional to
flux.
➢ Armature control method
➢ Voltage Control Method
➢ Variable resistance in series with armature.

2.3.1. FLUX CONTROL METHOD:

It is known that N α 1/ Φ by decreasing the flux, thus speed can be increased and vice versa.
Hence, name flux or field control method.
The flux of DC motor can be changed by changing Ish with help of a shunt field rheostat. Since
Ish in relatively small, shunt field rheostat has to carry only a small, so that rheostat is small in
size. This method therefore very efficient in non-interpolar machines the speed can be
increased by this method in the ratio 2:1 any further weakening of flux Φ adversely affect the
communication
And hence puts a limit to the maximum speed obtainable with this method in machines fitted
with interlopes in ratio of maximum to minimum speeds of 6:1 is fairly common.
The connection diagram for this type of speed control is shown in fig 2.

Page | 4
FIGURE 2: FLUX CONTROL METHOD

2.3.2. ARMATURE OR RHEOSTAT CONTROL METHOD:

FIGURE 3: RHEOSTAT CONTROL METHOD

Page | 5
Rheostat Control Method and Characteristics

This method is used when speeds below the no load speed are required. As the supply voltage
is normally constant, the voltage across the armature is varied by inserting a variable rheostat
or controller resistance in series with the armature circuit as shown in fig 3 as controller
resistance is increased, potential difference across the armature is decreased, thereby
decreasing the armature speed. For a load of constant torque, speed is approximately
proportional to the potential difference.

Across the armature current characteristics in fig. in seen that greater the resistance
In the armature circuit, greater is the fall in speed.

Let
Ia1 = Armature current in the first case
Ia2 = Armature current in the second case
N1, N2 = corresponding speeds
V = Supply voltage
Then N1 (v-Ia1Ra) αEb1
Let some controller resistance of value R be added to the armature circuit resistance so that its
value becomes
(R+Ra) = Rt
Then, N2 α (V-Ia2 Rt) α Eb2
N2/N1=Eb2/Eb1
Considering no load speed, we have
N/N0 (I-(Ia Rt)/ (V-Ia0 Ra)
Neglecting Iao Ra w.r.t. V, we get
N=No (I- (Ia Rt)/ V

FIGURE 4: SPEED VS ARMATURE CURRENT

Page | 6
It is seen that for a given resistance Rt the speed is a linear function of armature current Ia as
shown in fig. 4
The load current for which the speed would be zero is found by putting N=0 in above relation
0 = N0 ((I-Ia Rt)/V)
Or
Ia = V/Rt
This maximum current and is known as stalling current. This method is very wasteful,
expensive and unsuitable for rapidly changing loads because for a given value of Rt, speed will
change with load. A more stable operation can be obtained by using a diverter across the
armature in addition to armature control resistance.
Now, the changes in armature current will not be so effective in changing the potential
difference across the armature. The connection diagram for this type of speed control
arrangement is shown in fig.

2.3.3. VOLTAGE CONTROL METHOD:

1) MULTIPLE CONTROL VOLTAGE:

In this method, the shunt field of the motor is connected permanently to a fixed exciting voltage
but the armature is supplied with different voltages by connecting it across one at the several
different voltages by means of suitable switchgear. The armature will be approximately
proportional to these different voltages. The intermediate speeds can be obtained by adjusting
the shunt field regulator.

2) WARD-LEONARD SYSTEM:
This system is used where an unusually wide (up to 10:1) and very sensitive speed control is
required as for colliery winders, electric excavators and the main drives in steel mills and
blooming in paper mills.

Page | 7
The field of the motor (M1) is permanently connected across the DC supply lines whose
speed control can be done. The other motor M2 is directly connected to Generator G.

FIGURE 5: STRUCTURAL ARRANGEMENT OF WARD LEONARD SYSTEM

The output voltage of G is directly is fed to the main motor M1. The voltage of generator can
be varied from zero to up to its maximum value by means of field regulator.

By reversing the direction of the field current of G by means of the reversing switch which RS,
generated voltage can be reversed and hence the direction of rotation of M1. It should be
remembered that motor set always runs in the same direction.
The addition of a flywheel whose function is to reduce fluctuations in the Power demand from
the supply circuit.
The chief advantage of system is its overall efficiency especially at right loads. It has the
outstanding merit of giving wide speed Control from maximum in one direction through zero
to the maximum in the opposite direction and of giving a smooth acceleration.

Page | 8
2.3.4. PWM TECHNIQUE

Pulse width modulation control works by switching the power supplied to the motor on and off
very rapidly. The DC voltage is converted to a square wave signal, alternating between fully
on (nearly 12v) and zero, giving the motor a series of power “kicks”.
Pulse width modulation technique (PWM) is a technique for speed control which can overcome
the problem of poor starting performance of a motor.
PWM for motor speed control works in a very similar way. Instead of supplying a varying
voltage to a motor, it is supplied with a fixed voltage value (such as 12v) which starts it spinning
immediately. The voltage is then removed and the motor ‘coasts. By continuing this voltage
on/off cycle with a varying duty cycle, the motor speed can be controlled.

Page | 9
3. PWM TECHNIQUE:

Pulse-width modulation (PWM) or duty-cycle variation methods are commonly used in speed
control of DC motors. The duty cycle is defined as the percentage of digital ‘high’ to digital
‘low’ plus digital ‘high’ pulse-width during a PWM period.
Fig.2.7 shows the 5V pulses with 0% through 100% duty cycle. The average DC Voltage value
for 0% duty cycle is zero; with 20% duty cycle the average value is 1.2V (20% of 5V). With
50% duty cycle the average value is 2.5V, and if the duty cycle is 80%, the average voltage is
4V and so on. The maximum duty cycle can be 100%, which is equivalent to a DC waveform.

Thus, by varying the pulse-width, we can vary the average voltage across a DC motor and
hence its speed.

FIGURE 6: 5V Pulses With 0% Through 100% Duty Cycle

The average voltage is given by the following equation:


ý = D. Ymax + (1- D) Ymin
But usually minimum equals zero so the average voltage will be:
ý = D. Ymax
The circuit of a simple speed controller for a mini DC motor, such as that used in tape recorders
and toys, is shown in Fig 7.

Page | 10
FIGURE 7: SIMPLE SPEED CONTROLLER

Page | 11
4. DC motor speed control using PWM method:

The major reason for using pulse width modulation in DC motor control is to avoid the
excessive heat dissipation in linear power amplifiers. The heat dissipation problem often results
in large heat sinks and sometimes forced cooling. PWM amplifiers greatly reduce this problem
because of their much higher power conversion efficiency. Moreover, the input signal to the
PWM driver may be directly derived from any digital system without the need for any D/A
converters.
The PWM power amplifier is not without disadvantages. The desired signal is not translated to
a voltage amplitude but rather the time duration (or duty cycle) of a pulse.
This is obviously not a linear operation. But with a few assumptions, which are usually valid
in motor control, the PWM may be approximated as being linear (i.e., a pure gain). The linear
model of the PWM amplifier is based on the average voltage being equal to the integral of the
voltage waveform. Thus
VS * Ton = Veq * T
Where
VS = the supply voltage (+12 volts)
Ton = Pulse duration
Veq = the average or equivalent voltage seen by the motor
T = Switching period (1/f)
The recommended switching frequency is 300Hz.
The switching frequency (1/T), is determined by the motor and amplifier characteristics.
The control variable is the duty cycle which is Ton / T. The duty cycle must be recalculated at
each sampling time. The voltage that the motor sees is thus Veq, which is equal to the duty
cycle times the supply voltage.

4.1. Principle

Pulse width modulation control works by switching the power supplied to the motor on and off
very rapidly. The DC voltage is converted to a square wave signal, alternating between fully
on (nearly 12v) and zero, giving the motor a series of power “kicks”.

Page | 12
Pulse width modulation technique (PWM) is a technique for speed control which can overcome
the problem of poor starting performance of a motor.
PWM for motor speed control works in a very similar way. Instead of supplying a varying
voltage to a motor, it is supplied with a fixed voltage value (such as 12v) which starts it spinning
immediately. The voltage is then removed and the motor ‘coasts. By continuing this voltage
on/off cycle with a varying duty cycle, the motor speed can be controlled.
The wave forms in the below figure to explain the way in which this method of control operates.
In each case the signal has maximum and minimum voltages of 12v and 0v.
In wave form, the signal has a mark space ratio of 1:1, with the signal at 12v for 50% of the
time, the average voltage is 6v, so the motor runs at half its maximum speed.
In wave form, the signal has mark space ratio of 3:1, which means that the output is at 12v
for 75% of the time. This clearly gives an average output voltage of 9v, so the motor runs at 3/
4 of its maximum speed.
In wave form, the signal has mark space ratio is 1:3, giving an output signal that is 12v for
just 25% o the time. The average output voltage of this signal is just 3v, so the motor runs at
1/4 of its maximum speed.

By varying the mark space ratio of the signal over the full range, it is possible to obtain any
desired average output voltage from 0v to12v. The motor will work perfectly well, provided
that the frequency of the pulsed signal is set correctly, a suitable frequency being 30Hz.setting
the frequency too low gives jerky operation. And setting it too high might increase the motor’s
impedance.

1:1 Mark space ratio (50% duty cycle)

Page | 13
3:1 Mark space ratio (75% duty cycle)

1:3Mark space ratio (25%dutycycle)

FIGURE 8: Pulse Width Modulation Waveforms

4.2. METHODS
The pwm signals can be generated in a number of ways. there are several methods:
analogue method
digital method
discrete IC
4.2.1. Analogue method:
A block diagram of an analogue PWM generator is

FIGURE 9: Block Diagram of an Analogue PWM Generator

Page | 14
The simplest way to generate a PWM signal is the intersective method, which requires only a
saw tooth or a triangle wave form (easily generated using a simple oscillator) and a comparator.
When the value of the reference signal is more than the modulation wave form, the PWM signal
is in the high state, otherwise it is in the low state.

4.2.2. Digital Method:

The digital method involves incrementing a counter, an comparing the counter value with a
pre-loaded register value, or value set by an ADC. They normally use a counter that increments
periodically and is reset at the end very period of the PWM. When the counter value is more
than the reference value, the PWM output will change state from high to low.

4.2.3. PWM generator chips:

There are several IC’s available which converts a DC level into a PWM output. Many of
these are designed for use in switch mo power supplies. unfortunately, the devices designed
for switch mode power supplies not to allow the mark-space ratio to alter over the entire 0 –
100% range. Many limits the maximum to 90% which is effectively limiting the power you
can send to the motors.

Page | 15
5. SOLDERING
Soldering is the process of joining two or more electronic parts together by melting solder
around the connection. Solder is a metal alloy and when it cools it creates a strong electrical
bond between the parts. Even though soldering can create a permanent connection, it can also
be reversed using a desoldering tool as described below.

5.1. Soldering Iron


A soldering iron is a hand tool that plugs into a standard 120v AC outlet and heats up in order
to melt solder around electrical connections. This is one of the most important tools used in
soldering and it can come in a few variations such as pen or gun form. For beginners, it’s
recommended that you use the pen style soldering iron in the 15W to 30W range. Most
soldering irons have interchangeable tips that can be used for different soldering applications.
Be very cautious when using any type of soldering iron because it can heat up to 896′ F which
is extremely hot.

5.2. Soldering Station


A soldering station is a more advanced version of the basic standalone soldering pen. If you
are going to be doing a lot of soldering, these are great to have as they offer more flexibility
and control. The main benefit of a soldering station is the ability to precisely adjust the
temperature of the soldering iron which is great for a range of projects. These stations can also
create a safer workspace as some include advanced temperature sensors, alert settings and even
password protection for safety.

5.3. Soldering Iron Tips


At the end of most soldering irons is an interchangeable part known as a soldering tip. There
are many variations of this tip and they come in a wide variety of shapes and sizes. Each tip is
used for a specific purpose and offers a distinct advantage over another. The most common tips
you will use in electronics projects are the conical tip and the chisel tip.
Conical Tip – Used in precision electronics soldering because of the fine tip. Because of its
pointed end, it’s able to deliver heat to smaller areas without affecting its surroundings.
Chisel Tip – This tip is well-suited to soldering wires or other larger components because of
its broad flat tip.

Page | 16
5.4. Brass or Conventional Sponge
Using a sponge will help to keep the soldering iron tip clean by removing the oxidation that
forms. Tips with oxidation will tend to turn black and not accept solder as it did when it was
new. You could use a conventional wet sponge but this tends to shorten the lifespan of the tip
due to expansion and contraction. Also, a wet sponge will drop the temperature of the tip
temporarily when wiped.

5.5. Soldering Iron Stand


A soldering iron stand is very basic but very useful and handy to have. This stand helps prevent
the hot iron tip from coming in contact with flammable materials or causing accidental injury
to your hand. Most soldering stations come with this built in and also include a sponge or brass
sponge for cleaning the tip.
5.6. Solder
Solder is a metal alloy material that is melted to create a permanent bond between electrical
parts. It comes in both lead and lead-free variations with diameters of .032″ and .062″ being
the most common. Inside the solder core is a material known as flux which helps improve
electrical contact and its mechanical strength.

For electronics soldering, the most commonly used type is lead-free rosin core solder. This
type of solder is usually made up of a Tin/Copper alloy. You can also use leaded 60/40 (60%
tin, 40% lead) rosin core solder but it’s becoming less popular due to health concerns. If you
do use lead solder, make sure you have proper ventilation and that you wash your hands after
use.

Page | 17
6. BLOCK DIAGRAM:

POWER IC 555 TRANSISTOR MOTOR

SUPPLY TIMER TIP 122 (OUTPUT)

POTENTIOMETER

FIGURE 10: BLOCK DIAGRAM

Page | 18
6.1. BLOCK DIAGRAM DESCRIPTION:

6.1.1. POWER SUPPLY:

A power supply is an electrical device that supplies electric power to an electrical load. The
primary function of a power supply is to convert electric current from a source to the
correct voltage, current, and frequency to power the load. As a result, power supplies are
sometimes referred to as electric power converters. Some power supplies are separate standalone
pieces of equipment, while others are built into the load appliances that they power. All power
supplies have a power input connection, which receives energy in the form of electric current from
a source, and one or more power output connections that deliver current to the load.

In this project, we are providing 12V supply to the circuit through 12-0-12 transformer using
Capacitors, Voltage Regulator, Resistor, Diode and Led (Indicator).

FIGURE 11: 12V POWER SUPPLY

Page | 19
6.1.2. IC 555 TIMER:

The 555 timer IC is an integral part of electronics projects. The 555 timer IC is an integrated
circuit (chip) used in a variety of timer, pulse generation, and oscillator applications. The 555
can be used to provide time delays, as an oscillator, and as a flip-flop element. For a 555 timer
working as a flip flop or as a multi-vibrator, it has a particular set of configurations.

Some of the major features of the 555 timer would be:

• It operates from a wide range of power ranging from +5 Volts to +18 Volts supply
voltage.

• The external components should be selected properly so that the timing intervals can
be made into several minutes along with the frequencies exceeding several hundred
kilohertz.
• The output of a 555 timer can drive a transistor-transistor logic (TTL) due to its high
current output.
• The duty cycle of the timer is adjustable.
• The maximum power dissipation per package is 600 mW and its trigger and reset inputs
has logic compatibility.

Page | 20
6.1.2.1. PIN DIAGRAM OF IC 555 TIMER

FIGURE 12: PIN DIAGRAM OF IC 555 TIMER

PINS NAME PURPOSE

1. GND Ground reference voltage, low level (0 V)

The OUT pin goes high and a timing interval starts when this input falls
2. TRIG below 1/2 of CTRL voltage (which is typically 1/3 VCC, CTRL being 2/3
VCC by default if CTRL is left open)

3. OUT This output is driven to approximately 1.7 V below +VCC, or to GND.

Page | 21
A timing interval may be reset by driving this input to GND, but the
4. RESET timing does not begin again until RESET rises above approximately 0.7
volts. Overrides TRIG which overrides THR

Provides "control" access to the internal voltage divider (by default, 2/3
5. CNTL
VCC)

The timing (OUT high) interval ends when the voltage at THR
6. THR
("threshold") is greater than that at CTRL (2/3 VCC if CTRL is open)

Open collector output which may discharge a capacitor between


7. DIS
intervals. In phase with output.

Positive supply voltage, which is usually between 3 and 15 V depending


8. VCC
on the variation

6.1.2.2. 555 TIMER WORKING:

The 555 generally operates in 3 modes:

1. Astable
2. Mono-stable
3. Bi-stable modes.

In this circuit, Astable mode is being used. This means there will be no stable level at the
output. So, the output will be swinging between high and low. This character of unstable output
is used as a clock or square wave output for many applications.

Page | 22
FIGURE 13: IC 555 TIMER

6.1.3. TRANSISTOR:

In this circuit, we use TIP122 (Darlington NPN) transistor. The TIP122 is a Darlington pair
NPN transistor. It functions like a normal NPN transistor, but since it has a Darlington pair
inside it has a good collector current rating of about 5A and a gain of about 1000. It can also
withstand about 100V across its collector- Emitter hence can be used to drive heavy loads. The
Darlington pair inside this transistor is shown clearly as its internal circuit schematic below

FIGURE 14: DARLINGTON PAIR NPN TRANSISTOR

Page | 23
There are two transistors inside this TO-220 package in which the emitter of the first transistor
is connected with the base of the second transistor and the collector of both transistors are
connected together to form a Darlington pair. This increases the current gain and current rating
of this transistor.

FIGURE 15: TIP122

6.1.3.1. APPLICATION:

• Can be used to switch high current (upto 5A) loads


• Can be used as medium Power switches
• Used where high amplification is needed
• Speed control of Motors
• Inverter and other rectifier circuits

6.1.4. DC MOTOR:

A DC motor is any of a class of rotary electrical machines that converts direct current
electrical energy into mechanical energy. The most common types rely on the forces
produced by magnetic fields. Nearly all types of DC motors have some internal mechanism,

Page | 24
either electromechanical or electronic, to periodically change the direction of current flow
in part of the motor.

In this project, we use 12V DC motor.

FIGURE 16: 12V DC MOTOR

6.1.5. POTENTIOMETER:

A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an


adjustable voltage divider . If only two terminals are used, one end and the wiper, it acts as
a variable resistor or rheostat.

In this project, we use 100 KΩ potentiometer.

FIGURE 17: POTENTIOMETER

Page | 25
7. COMPONENTS:

7.1. COMPONENTS REQUIRED FOR SPEED CONTROL


1. NE555P TIMER IC
2. 1KΩ Resistor × 2
3. 100 nF Capacitor × 2
4. 1N4007 Diode × 3
5. 100KΩ Potentiometer
6. Transistor (Darlington TIP122)
7. 12V Power Supply
8. 12V DC Motor
9. Connecting Wire

7.2. COMPONENT LIST OF 12V POWER SUPPLY


1. Transformer (12-0-12)
2. 1N4007 Diode × 4
3. Capacitor (470 µF, 25V)
4. Capacitor (0.1 µF) ×2
5. Regulator (IC2 7812)
6. 4.7 KΩ Resistor
7. LED bulb

Page | 26
8. CIRCUIT DIAGRAM :

8.1. CIRCUIT DIAGRAM FOR SPEED CONTROL

FIGURE 18: CIRCUIT DIAGRAM

Page | 27
8.1.1. WORKING OF THE CIRCUIT:

The 555 Timer is capable of generating PWM signal when set up in an astable mode. In this
circuit, the DC motor is operated by a 555 integrated circuit. The IC 555 in this circuit is being
operated in astable mode, which produces a continuous HIGH and LOW pulses. In this mode,
the 555 IC can be used as a pulse width modulator with a few small adjustments to the circuit.
The frequency of operation of the circuit is provided by the passive parameters of resistances
and capacitors attached to it.

Here’s a basic circuit of the 555 Timer operating in an astable mode and we can notice that the
output is HIGH when the capacitor C1 is charging through the resistors R1 and R2. On the
other hand, the output of the IC is LOW when the capacitor C1 is discharging but only through
the resistor R2. So, we can notice that if we change the values of any of these three components,
we will get different ON and OFF times, or different duty cycle of the square wave output
signal. An easy and instant way to do this is to replace the R2 resistor with a potentiometer,
and additionally add two diodes in the circuit.

In this configuration the ON time will depend on the resistor R1, the left side of the
potentiometer and the capacitor C1, while the Off time will depend on the capacitor C1 and the
right side of the potentiometer. We can also notice that in this configuration the period of one
cycle, thus the frequency, will always be the same, because the total resistance, while charging
and discharging, will remain the same.

Usually the R1 resistance is much smaller than the resistance of the potentiometer, for example,
1K compared to 100K of the potentiometer. In that way we have 99% control over the charging
and discharging resistance in the circuit. The control pin of the 555 Timer is not used but it’s
connected to a 100nF capacitor in order to eliminate any external noise from that terminal. The
reset, pin number 4, is active low so therefore it is connected to VCC in order to prevent any
unwanted reset of the output.

The output of the 555 timers can sink or source a current of 200mA to the load. So, if the motor
that we want to control exceeds this rating we need to use a transistor or a MOSFET for driving
the motor. In this circuit, I used a (TIP122) Darlington transistor which can handle a current
up to 5A.

Page | 28
8.2. CIRCUIT DIAGRAM FOR 12V POWER SUPPLY

FIGURE 19: CIRCUIT DIAGRAM FOR 12V SUPPLY

8.2.1. WORKING OF THE CIRCUIT:

The objective of this project is to convert 220V AC supply in to +12V and -12v DC supply,
that is why it is named Dual Power Supply as we get positive and negative 12v power supply
at the same time.

This can be achieved in simple three steps:

1. Firstly, 220V AC is converted into 12V AC by using simple step-down (220V/12V)


transformer.
2. Secondly, output of this transformer is given to the rectifier circuit, which will convert the
ac supply into dc supply. The output of the rectifier circuit that is DC contains the ripples in
the output voltage. To filter out these ripples, capacitor of 470 uf and 0.1uf.

Page | 29
3. Lastly, the output of the capacitor that is pure DC is given to voltage regulator IC 7812
which will regulate the output voltage at 12V and -12V DC, despite the change in input
voltage.

8.2.1.1. Converting 220v AC into 12v AC using Step Down Transformer

The primary terminals of the centre tapped transformer is connected with household supply
(220V ac, 50Hz) and output is taken from secondary terminals of the transformer. The centre
tapped describes the voltage output of a center tapped transformer. For example: A 24V centre
tapped transformer will measure 24V ac across the outer two taps (winding as a whole), and
12V ac from each outer tap to the center-tap (half winding). These two 12V ac supplies are
180 degrees out of phase with each other, thus making it easy to derive positive and negative
12 volt dc power supplies from them. The advantage of using a centre tapped transformer is
we can get the both +12V and -12V DC supply using only one transformer.

8.2.1.2. Converting 12v AC into 12v DC using Full Bridge Rectifier


The outer two terminals of the centre tapped transformer are connected to the bridge rectifier
circuit. Rectifier circuit is a converter, which converts ac supply in to dc supply. It is generally
made up of diode switches as shown in Circuit Diagram.

To convert ac into dc, we can make two types of rectifiers, one is half bridge rectifier and
second is full bridge rectifier. In half bridge rectifier, output voltage is half of the input voltage.
For example, if input voltage is 24V, then output dc voltage is 12V and number of diode used
in this type of rectifier is 2. In full bridge rectifier, number of diodes is 4 and it is connected as
shown in figure and output voltage is same as the input voltage.

Here, full bridge rectifier is used. So, number of diodes are 4 and input voltage (24V ac) and
output voltage is also 24V dc with ripples in it.

For, full bridge rectifier output voltage,

VDC = 2Vm / Π where, Vm=peak value of ac supply voltage and Π is Pi

Page | 30
The waveform of input and output voltage of full bridge rectifier is as shown below.

FIGURE 20: FULL WAVE BRIDGE RECTIFIER WITH INPUT AND OUTPUT
WAVEFORM

In this Dual Power Supply Circuit, Diode bridge rectifier is made up of 6A four power diodes.
Rating of this diode is 6A and 400V. It is not necessary to use this much of high current capacity
diode but because of safety and flexibility purpose, high current capacity diode is used.
Generally, because of surges in current, it is possible to damage the diode, if we used low
ampere rating diode.

The output of rectifier is not pure dc, but it contains ripples in it.

INPUT: 12V ac

OUTPUT: 24V peak (with ripples)

8.2.1.3. Filter the Ripples from the output:

24V dc output which contains peak to peak ripples can’t be connected directly to the load. So,
to remove ripples from the supply, filter capacitors are used. Now, two filter capacitor of
rating 470uF and 0.1uF are used as shown in circuit diagram. The connection of both
capacitors is such that the common terminal of the capacitors is connected directly to the
centre terminal of the centre tapped transformer. Now, this capacitor will get charged upto

Page | 31
12V dc as both are connected with the common terminal of a transformer. Furthermore, the
capacitors will remove the ripples from the dc supply and give a pure dc output. But, the
output of both the capacitors are not regulated. So, to make the supply regulated, output of
the capacitors is given to the voltage regulator ICs which is explained in next step.

INPUT: 12V dc (with ripples, not pure)

OUTPUT: Voltage across capacitor C1 =12V dc (pure dc, but not regulated)

Voltage across capacitor C2 =12V dc (pure dc, but not regulated)

8.2.1.4. Regulate the 12v DC Power Supply

The next important thing is to regulate the output voltage of the capacitors which will otherwise
be varying as per the input voltage change. For that depending upon the output voltage
requirement, regulator ICs are used. If we need the output voltage +12V then IC 7812 is used.
If required output voltage is +5V, then 7805 IC is used. Last two digits of the IC gives output
voltage rating. Third last digit shows voltage is positive or negative. For positive voltage (8)
and for negative voltage (9) number is used. So IC7812 is used for +12v regulation and IC7912
is used for -12v voltage regulation.

Now connection of two ICs are done as shown in circuit diagram. The ground terminal of both
ICs are connected with the centre tap terminal of the transformer in order to create a reference.
Now, the output voltages are measured between the output terminal and ground terminal for
both ICs.

INPUT: 12V dc (pure dc but not regulated)

OUTPUT: +12V dc between output terminal of 7812 and Ground (pure dc and regulated)

-12V dc between output terminal of 7912 and Ground (pure dc and regulated)

Page | 32
9. HARDWARE MODEL:

FIGURE 21: 12V SUPPLY CIRCUIT FIGURE 22: CIRCUIT FOR SPEED
CONTROL

FIGURE 23: COMPLETE CIRCUIT

Page | 33
10. RESULT AND DISCUSSION:

By varying the ohmic pot we have done the speed control DC shunt motor by means of PWM
method for triggering the base of controlled device called IGBT. We found out that this is
very cheap and efficient speed control method where all components give reliable operation
and we have checked it experimentally where the efficiency of rheostatic method is better
than the PWM control method.

Figure 4 shows the pulses at different duty cycles. The pulse with higher duty cycle turns ‘ON’
at longer time than that of lower duty cycle. The duty cycle, d is governed by equation

d = ton/T

where T is the duration of one period and ton is the ‘ON’ time. The ratio of ON to OFF time is
called as duty cycle which determines the speed of the motor. The desired speed can be
obtained by changing the duty cycle. The PWM pulse is used to control duty cycle of DC motor
drive. Power is supplied to the motor in square wave of constant voltage but varying pulse-
width or duty cycle. Duty cycle refers to the percentage of one cycle during which duty cycle
of a continuous train of pulses. Since the frequency is held constant while the on-off time is
varied, the duty cycle of PWM is determined by the pulse width. Thus, the power increases
duty cycle in PWM. The PWM ON period at 60 % of duty cycle is higher than at 40 % duty
cycle. This contributes to higher motor speed at 60 % duty cycle compared to 40 % duty cycle.
Figure 5 shows the pulses at switching frequency of 500 Hz and 1500 Hz. The frequency of
operation, f is defined as
f = 1/(ton + toff) = 1/T

Where ton is the ON time of the PWM pulse, toff is the ‘OFF’ time in which the value of PWM
pulse is at zero level and T is the total time period of one duty cycle. Higher switching
frequency increases the output voltage.

Page | 34
Figure 24: Pulse at different duty cycle.

Figure 25: Pulse at different frequencies.

Figure 26 shows the motor voltage and speed at different frequencies. The voltage increases
steeply from 9.56 V to 10.74 V as the frequency is increased from 500 Hz to 1500 Hz. However,
the voltage increases gradually as the frequency is beyond 2000 Hz. This is due to the higher
loss at higher frequency (Obed, 2011). It is obvious that the speed increases with increasing of
switching frequency. For instance, the speed increases from 4213 to 4722 RPM as the
frequency is increased from 500 Hz to 3000 Hz. The average output voltage is governed by
Vav= (ton/T) * Vm

Page | 35
where, ton is the ON period of PWM pulse, T is the total time period of the one duty cycle and
Vin is the input voltage.

Figure 26: Motor speed and voltage at different PWM frequency

Figure 27 shows the motor speed and voltage at different duty cycle for the configuration
shown in figure 24. The duty cycle was set from 20 % to 99 %. When the duty cycle is increased
the motor speedis also increased. At 20 % duty cycle, the motor speed is 2332 RPM and the
converter output voltage is 5.4 V. As the duty cycle increased to 40 %, the motor speed is 2470
RPM and the converter output voltage is 5.82 V. The motor speed and converter output voltage
increasing as the duty cycle increases to 60% and 80 %. The maximum speed of 2892 RPM
and the maximum voltage were achieved at 99 % duty cycle. This shows that the speed
increases as the duty cycle increases.

Figure 27: Motor speed and voltage at different duty cycle


Page | 36
11. CONCLUSION:
The dc motor speed is controlled by using power electronic device and the PWM is used which
to control the speed of dc motor. The speed pulse train will be based on required input speed.
This circuit is useful to operate the dc motors at required speed with very low losses and low
cost. The circuit response time is fast. Hence high reliability can be achieved. The designed
circuit was tested for various speed inputs satisfactorily. The method already employed in
traction system and has a good scope ahead.

Page | 37
12. FUTURE SCOPE:

1. DC motor plays a significant role in modern industries. They are widely used in industry
because of its low cost, less complex control structure and wide range of speed and torque so
better future of this project.

2. In this project we are used pulse width modulation technique, it is a modern technology in
solid state field and it provide smooth speed control of motor.

3. Now a day PWM technique are using in fuzzy logic control system, so PWM method is very
efficient and reliable method to control the speed of motor so it future is also bright in the
modern era with fuzzy logic.

Page | 38
APPENDIX:

S.No. Components SPECIFICATION Quantity Purpose


The 555 can be used to
provide time delays, as
1 IC 555 TIMER - 1
an oscillator, and as
a flip-flop element.
1kΩ 2 resistor is used to limit
2 RESISTOR
4.7kΩ 1 the current.
470µF,25V 1 capacitors are used in
0.1µF 2 power supplies where
3 CAPACITOR they smooth the output
100nF 2 of a full or half wave
rectifier.
A rectifier diode is used
as a one-way check
valve. Since
1A,3W
these diodes only allow
4 1N4007 DIODE Reverse Current- 7
electrical current to flow
5µA
in one direction, they are
used to convert AC
power into DC power.
The Potentiometer is an
electric instrument that
used to measure the EMF
(electro motive force) of
a given cell, the internal
5 POTENTIOMETER 100kΩ 1
resistance of a cell. And
also, it is used to
compare EMFs of
different cells. It can also
use as a variable resistor

Page | 39
in most of the
applications.
A transistor is a
semiconductor device
5.0A,60-
6 TRANSISTOR 1 used to amplify or switch
100V,65W
electronic signals and
electrical power.
A DC motor is any of a
class of rotary electrical
machines that
7 DC MOTOR 12V 1
converts direct
current electrical energy
into mechanical energy.
Transformers (sometimes
called
"voltage transformers")
are devices used in
electrical circuits to
change the voltage of
electricity flowing in the
8 TRANSFORMER 12-0-12V 1
circuit.
Transformers can be
used either to increase
the voltage (called
"stepping up") or
decrease the voltage
("step down").
IC 7812 and 7912 are
used for the purpose of
9 IC2 7812 - 1 voltage regulation in
which the former is a
positive 12V regulator

Page | 40
and later is a negative
12V regulator
A light-emitting diode
(LED) is a
semiconductor light
source that emits light
when current flows
10 LED BULB 3V,50mA 1
through it. Electrons in
the semiconductor
recombine with electron
holes, releasing energy in
the form of photons.

Page | 41
REFERENCES:
[1]. Arvind, S.K., Arun, T.A., Madhukar, T.S., &Deka, J., (2014). Speed Control of DC Motor
using PIC 16F877A Microcontroller. Multidisciplinary Journal of Research in Engineering and
Technology, 1(2), 223-234.
[2]. Bansal, U. K.&Narvey, R. (2013). Speed control of DC motor using fuzzy PID controller.
Advance in Electronic and Electric Engineering. 3(9) , 1209-1220.
[3]. Bakibillah,A.S.M.,Rahman, N., & Zaman, U. A. (2014).Microcontroller based Closed
Loop Speed Control of DC Motor using PWM Technique.International Journal of Computer
Applications, 108(14), 15-18.
[4]. Chauhan., J. S.& Semwal, S. (2013). Microcontroller Based Speed Control of DC Geared
Motor through RS-232 Interface with PC. International Journal of Engineering Research and
Applications, 3(1), 778-783.
[5]. Gupta, R., Lamba, & Padhee, (2012). Thyristor Based Speed Control Techniques of DC
Motor: A Comparative Analysis. International Journal of Scientific and Research Publications,
2 (6). 1-6.
[6]. Kapil, P.N., &Patel, K. (2015).Simulation Of PWM Controller Based DC Motor.
International Journal of Current Engineering and Scientific Research, 2(5), 65-68.
[7]. Obed, A.A., &Basheer, A.(2011).Effect of duty cycle and chopper frequency of PWM DC-
DCconverter drive on performance characteristics of DC motor.The fourth International
scientific Conference of Salahaddi University-Erbil, 87-92.
[8]. Shrivastava, S., Rawat, J.&Agrawal, A.(2012).Controlling DC Motor using
Microcontroller (PIC16F72) with PWM.International Journal of Engineering Research, 1(2),
45-47.

[9].Gopal K Dubey “Fundamentals of Electric Drives” Narosa Publishing House New Delhi,
1989.
[10].Muhammad H. Rashid, ‘‘Power Electronics Circuits, Devices, and Applications,” Prentice
Hall, 3rd edition, 2003.
[11]. Kumara MKSC, Dayananda PRD, Gunatillaka MDPR, Jayawickrama SS, “PC based
speed controlling of a dc motor”, A fmal year report University of Moratuwa
Illiniaus USA, 2001102.
[12]. J Nicolai and T Castagnet , “A Flexible Micro controller Based Chopper Driving a
Permanent Magnet DC Motor”, The European Power Electronics

Page | 42
Application. 1993
[13]. A Khoei Kh. Hadidi, “MicroProcessor Based Closed- Loop Speed Control System for
DC Motor Using Power MOSFET”, 3rd IEEE international conference
on Electronics, Circuits and Systems( 1996) vol.2, pp.1247-1250.

Page | 43

You might also like