Country Dry Sink

Country Dry Sink
This dry sink will give your kitchen a feel

that no modern cabinet could.
Traditional American dry sinks were made

from yellow pine and had deep wooden
troughs on top that were useful for storing
pitchers, churns and buckets of liquids. Now
that we’ve got refrigerators and ice makers,
the dry sink has graduated to become an
expensive item at antique markets.
This updated version preserves the form of

the traditional dry sink, with its high splash
guard on back and storage down below, but
Begin building the top by gluing and nailing the side
I’ve altered a few key components. Instead of splash pieces to the back splash pieces. I like to hold the
a sunken wooden trough on top, I’ve added back splash in place using a vise to keep everything in
two drawers. And instead of yellow pine, this line as it’s nailed together.
dry sink is made from curly maple. Put the
finished project in your kitchen to add a
country touch to a farm home, or use it as a
buffet in an informal dining room.
Traditional Construction
I build all my casework the same way, and

I’m convinced that these methods will ensure Now glue and nail the splash pieces to the top. Turn
the splash upside-down and put a bead of glue on the
that the furniture will be around for a long entire length of the back splash. Then put a bead of glue
time. Begin by building the face frame of the on the back third of the side splash. If you glue the entire
cabinet because most of the cabinet side splash, your top might bust apart after a few seasons.
dimensions are based on the face frame. I
use mortise-and-tenon joinery to join the rails
and stiles. I make the tenons on all the rails
1" long, and all the mortises 11/16" deep,
which will ensure your tenons won’t bottom
out in your mortises and give some space for
excess glue to go. Dry-fit the face-frame
parts, then put glue in the mortises and glue
up all the rails and stiles. Start with the center
rail and stile and work out. Place the top on the splash assembly and nail it in
place through the underside of the top.
Doors Next
Once the glue is dry from the face frame, I
like to make my doors because they are
easier to hang and fit while the face frame
can be laid flat on my bench. The doors are
built much the same way as the face frame,
with 1"-long tenons on the rails. To hold the
panel in place, I plow a 3/8" x 3/8" groove
down the inside edge of all the door parts. Be
sure to make the tenons on the rails
haunched because of this groove.
Once you have the rails and stiles fit,

measure the opening for the panel and cut
your stock to size, making sure that you leave Now put a bead of glue on the side pieces and top rail of
the face frame. . . .
a 1/8" gap all around to accommodate wood
movement in the panel. I cut an 8° bevel on
the edges of the panel using my shaper,
though you can easily cut this bevel by tilting
the blade about 12° on your table saw. Finish
sand the panel and add one coat of stain.
Place the panel in the groove, glue up the

mortise-and-tenon joints and clamp the
doors. You’ll notice that I make the doors the
same size as my opening in the face frame.
. . .The sides will expand and contract the same as the
This is on purpose. Once my doors are sides pieces so there isn’t a cross-grain problem here.
complete, I trim them to size on my jointer. Toenail the top into the case piece.
Hang the doors in the face frame, then
remove the doors and move onto the case.
Build the Case
Begin building the case by gluing up some

boards to make the side pieces and shelves.
Once those are cut to finished size, cut ¾"-
wide x ¼"-deep dadoes to hold the two fixed
shelves in place.
The bottom dado is located 4¾" from the

bottom edge of sides. This will make the
bottom shelf stick up ¼" above the bottom rail
of the face frame and serve as a door stop.
The second dado should be flush to the top
of the center rail because the drawers will
ride on that shelf. Now cut ½" x ¼" rabbets in
the sides for the back.
Put a bead of glue in the dadoes, then put the

shelves in the dadoes and nail the case
together through the sides. Some people
might wince at nailing a case together this
way; I don’t. I figure that when the glue finally
gives way, as it will someday, it’s the nails
that will hold the piece together.
Now nail the nailing strip between the sides.

The nailing strip should be flush to the top of
the sides and ½" in from the back edge of the
sides. You’ll nail your back to this when the
project is complete.
To complete the lower case, glue and nail the

face frame to the case. When the glue is dry,
cut the shape of the base on the front and
sides using a jigsaw. Then clean up your cuts
using sandpaper. Now it’s time to move on to
the top.
Make the Top to Last
There’s some cross-grain construction in the

top, so you need to be careful about how you
put it together to ensure the top doesn’t self-
destruct.
Begin by gluing up the boards for the top

piece, cutting the top to finished size and
sanding it to its final grit. Cut a ¼" x ¼"
chamfer on the top edge to soften the edge.
Cut your three splash pieces to size and cut
the curved parts. The back splash gets a 3"
radius cut on either end. And the side
splashes get a 1" radius cut on the front edge
as shown in the drawings. Finish sand all the
pieces and follow the instructions under the
photos.
Finishing Touches
I make the drawers using half-blind dovetails.

I build a simple jig that cranks these out in
just a few minutes. See the jig in action at
www.popwood.com/features/ fea33.html.
To keep the drawers running straight, I nailed

in ¾" x 1" strips of wood on the upper fixed
shelf and stops at the back of the case to
keep the drawer fronts flush to the front of the
case.
The back is made from ½"-thick poplar
boards that I shiplap so the edges overlap. I
also cut a bead on the shiplapped edges
using a beading bit in my router. Fit the back
pieces, being sure to leave a gap between
each board; don’t nail them in place until the
dry sink is finished.
Now finish sand all the parts, putty your nail

holes and dye the project. I use a diluted red
aniline dye, followed by three coats of
lacquer. PW

Country Dry Sink

Uploaded by

Copyright:

Available Formats

Country Dry Sink

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Country Dry Sink

Uploaded by

Copyright:

Available Formats

How is the dry sink constructed?

How is the dry sink constructed?

What joinery techniques are used?

What joinery techniques are used?

Country Dry Sink

This dry sink will give your kitchen a feel

Traditional American dry sinks were made

This updated version preserves the form of

I build all my casework the same way, and

Once you have the rails and stiles fit,

Place the panel in the groove, glue up the

Build the Case

Begin building the case by gluing up some

The bottom dado is located 4¾" from the

Put a bead of glue in the dadoes, then put the

Now nail the nailing strip between the sides.

To complete the lower case, glue and nail the

Make the Top to Last

There’s some cross-grain construction in the

Begin by gluing up the boards for the top

I make the drawers using half-blind dovetails.

To keep the drawers running straight, I nailed

Now finish sand all the parts, putty your nail

You might also like