Scribd
Upload
195 views1 page

Beam Longitudinal Section: Moment Diagram

This document presents the design calculations for reinforcing a concrete beam. It includes the load calculations, moment diagrams, and design of the main reinforcement. The beam is subjected to a 25 kN point load at each end. The maximum bending moment is -50 kNm^2 at the center. The required steel is calculated to be 3 bars of 20mm diameter based on the moment capacity and steel ratio. Stirrups of 10mm diameter are specified at 40mm spacing. Drawings show the beam cross section and reinforcement details.

Uploaded by

Love Joey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
195 views1 page

Beam Longitudinal Section: Moment Diagram

This document presents the design calculations for reinforcing a concrete beam. It includes the load calculations, moment diagrams, and design of the main reinforcement. The beam is subjected to a 25 kN point load at each end. The maximum bending moment is -50 kNm^2 at the center. The required steel is calculated to be 3 bars of 20mm diameter based on the moment capacity and steel ratio. Stirrups of 10mm diameter are specified at 40mm spacing. Drawings show the beam cross section and reinforcement details.

Uploaded by

Love Joey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

–

w = 25 kN

M1= -(wl_2^3+wl_1^3)/(8(l_1+l_2))
= -(〖25(4)〗^3+〖25(4)〗^3)/(8(4+4))
M=-50 k〖Nm〗^2

R1 = 25 kN R3 = 25 kN
V1=V_3 and V_2=V_4 a = 2.7478m a = 2.7478m

R3 = 125 kN
V1= R_1= R_3

R1=M_1/l_1 +〖wl〗_1/2 Assumptions Mx1= = 12.50 kN² Mx3= = 12.50 kN²

=50/4+25/2 b – 335 mm
MOMENT DIAGRAM
R(1 ,3)=25 kNm^2 h– 670 mm
fc’ – 27.6 MPa
V2=〖wl〗_1-R_1 fy - 413.0 MPa
=(25)(4)-25 d- 610 mm Mx2= = -50 kN²
V2= 75 use 20 mm Ø main bars
A B A
Ratio and Proportion
25 100
x x 4
x=1
A B A
Mx1=R1 x1 - (wx_12)/2
=(25)(1)-((25)(1)2)/2 BEAM LONGITUDINAL SECTION
Mx1=12.50 kNm2
2 pcs. 10mm DIA. 3 pcs- 20 mm DIA. REBARS
DISTRIBUTION BARS

BEAM TRANSVERSE SECTION


10mm DIA. STIRRUPS 10mm DIA. STIRRUPS
40mm 40mm

3 pcs- 20 mm DIA. REBARS Mu 12.50 kNm^2 -50 k〖Nm〗^2 12.50 kNm^2


h = 670 mm h = 670 mm 2 pcs. 10mm DIA.
DISTRIBUTION BARS
Ru=Mu/((φbd^2)) 0.11 0.45 0.11
10mm 10mm ρ=(0.85)((fc^')/fy)(1-√(1-2Ru/(0.85)(fc^' ) )) .000267 .0011 .000267

Check p min
pmin=1.4/314 (use p min) .0045 .0045 .0045

40mm 40mm Ast=pbd 919.58 919.58 919.58


10mm 10mm A_(20=(π(20)^2)/4) 314.6 mm2 314.6 mm2 314.6 mm2
b = 335mm b = 335mm

Number of bars= Ast/A 2.92 ≈ 3 2.92 ≈ 3 2.92 ≈ 3


BEAM TRANSVERSE SECTION DETAIL (A-A) BEAM TRANSVERSE SECTION DETAIL (B-B)

SUBJECT TITLE: R E M A R K S
SUB MITTE D B Y:

UNIVERSITY OF SCIENCE AND JENNYVIL C. NUNEZ


TECHNOLOGY OF SOUTHERN PHILIPPINES BS - ARCHITECTURE 5A
D:\Desktop\SAD.png
SUBMITTED TO :
C. M. RE CTO AVENUE, LAPASAN, CAGAYAN DE ORO CITY
CE66: REINFORCED CONCRETE DESIGN
ENGR. ERNESTO C. QUIJOTE
INSTRUCTOR

You might also like