Model 6 Operating Instructions

IMPORTANT SAFETY INFORMATION AND
INSTRUCTIONS FOR In the USA and Canada,

our 24 hour hotline is:
ENGINE SELECTION 18002333723
ENGINE INSTALLATION Briggs & Stratton Corporation
Milwaukee, Wisconsin 53201
ENGINE OPERATION
www.briggsandstratton.com
Keep these instructions for future reference.
Before installing and operating this engine

read and observe all warnings, cautions and
instructions on both sides of this sheet, on the engine,
and in the operating & maintenance instructions.
NOTE: This sheet of instructions and safety information is not meant to cover all
possible conditions and situations that may occur. Read entire Operating &
Maintenance Instructions for this engine AND the instructions for the equipment
this engine powers. Failure to follow instructions and safety information could
result in serious injury or death.
The safety alert symbol ( )is used to identify safety

HAZARD SYMBOLS AND MEANINGS
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of
injury. In addition, a hazard symbol may be used to represent the type Fire Explosion Moving Parts
of hazard.
DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.
Toxic Fumes Hot Surface Shock
WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury. Kickback
CAUTION, when used without the alert symbol,

indicates a situation that could result in damage to
the engine. (OVER)
FORM MS -6445 -01/03
ENGINE SELECTION
[8] All engine parts, including fuel
WARNING WARNING cap, spark plug, muffler, air
cleaner, and covers and guards
for drive components (gears,
belts, shafts, couplings, etc.)
must be in place before attempt-
ing to start engine.
Failure to select the correct engine could [9] If engine is installed on walk
result in fire or explosion. WARNING behind lawn mower, all mower
components, including cutting
• Some engines are unique and designed for specific applications blade, must be correctly
or types of equipment. If this engine will be used to build new installed before attempting to
equipment, contact Briggs & Stratton to ensure that the engine is start engine.
appropriate for the intended use. [10] When working on the engine or
Note: For all Go -karts use only a model 136200 series en-
gine, which offers improved safety and performance.
WARNING equipment, remove spark plug
wire from spark plug. For electric
• Replacement engines should be the same model as the original
engine, or be the Briggs & Stratton designated replacement start, remove negative wire from
engine. Refer to the Operation & Maintenance Instructions for battery.
engine identification information.
[11]
Note: For all Go -karts use only a model 136200 series en- Do not check for spark with
gine, which offers improved safety and performance. WARNING spark plug removed. Use Briggs
• Do not use Briggs & Stratton engines on 3 -wheel All -Terrain & Stratton spark tester #19368.
Vehicles (ATVs), motor bikes, air craft products, or vehicles
intended for use in competitive events. Briggs & Stratton does not
approve of or authorize such uses.
ENGINE OPERATION
ENGINE INSTALLATION
[1] Do not attempt to install this engine if you do not have the WARNING
appropriate tools and knowledge of small engine installation
procedures. Use only Briggs & Stratton parts. Contact your When adding fuel:
Authorized Service Dealer for assistance.
[2] Do not modify the engine in any way without Briggs & Stratton Turn engine off and let engine cool at least 2 minutes before
factory approval. Any such modification is at the owner’s sole removing gas cap.
risk. Fill fuel tank outdoors or in well-ventilated area. Fill tank to about
[3] If the exhaust system on the old engine was supplied by the 1 inch below lowest portion of neck to allow for fuel expansion.
equipment manufacturer, you must transfer the exhaust Keep gasoline away from sparks, open flames, pilot lights, heat,
system and related components (original muffler and related and other ignition sources.
pipes, brackets, clamps, and shields) to the new engine. All
components must be in good condition.
[4]
WARNING
Install muffler (and muffler de- WARNING
flector if used) so outlet points
away from operator, fuel tank, When starting engine:
and equipment, and so muffler
heat will not damage or deform Remove all external equipment/engine loads.
engine and components.
Wait until spilled fuel is evaporated. Start engine outdoors.
[5] Ensure all fuel lines and fittings Pull cord slowly until resistance is felt, then pull rapidly.
WARNING are properly assembled and do If engine floods, set choke to OPEN/RUN, place throttle in FAST
not leak. Replacement parts and crank until engine starts.
must be the same model as the
original.
[6] Ensure all wiring, including safe-

WARNING
WARNING ty switches and engine shut-off
components are completely When operating equipment:
installed and functioning proper-
ly. Do not tip engine or equipment at angle which causes gasoline to
spill.
[7] Set engine speed to equipment manufacturer’s specification. Run engine outdoors. Do not run in enclosed area, even if doors
Refer to equipment manufacturer’s manual. Do not tamper with or windows are open.
governor springs, or other parts that will increase engine speed Do not choke carburetor to stop engine.
above specification.
FORM MS -6445 -01/03

Model 6 Operating Instructions

Uploaded by

Copyright:

Available Formats

Model 6 Operating Instructions

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Model 6 Operating Instructions

Uploaded by

Copyright:

Available Formats

What safety precautions should be taken when installing an engine?

What safety precautions should be taken when operating an engine?

IMPORTANT SAFETY INFORMATION AND

INSTRUCTIONS FOR In the USA and Canada,

Before installing and operating this engine

The safety alert symbol ( )is used to identify safety

A signal word (DANGER, WARNING, or CAUTION) is used with the

DANGER indicates a hazard which, if not avoided,

Toxic Fumes Hot Surface Shock

WARNING indicates a hazard which, if not

CAUTION indicates a hazard which, if not avoided,

CAUTION, when used without the alert symbol,

[6] Ensure all wiring, including safe-

You might also like