Ta7805sb, Ta78057sb, Ta7806sb, Ta7807sb, Ta7808sb, Ta7809sb, Ta7810sb, Ta7812sb, Ta7815sb, Ta7818sb, Ta7820sb, Ta7824sb
Ta7805sb, Ta78057sb, Ta7806sb, Ta7807sb, Ta7808sb, Ta7809sb, Ta7810sb, Ta7812sb, Ta7815sb, Ta7818sb, Ta7820sb, Ta7824sb
Ta7805sb, Ta78057sb, Ta7806sb, Ta7807sb, Ta7808sb, Ta7809sb, Ta7810sb, Ta7812sb, Ta7815sb, Ta7818sb, Ta7820sb, Ta7824sb
Features
z Suitable for CMOS, TTL and the power supply of other digital
ICs
z Internal thermal shutdown protection
z Internal overcurrent protection
z Maximum output current of 1 A
z Package in the plastic case TPL (PD: 1.8 W)
Pin Assignment
Marking
Lot No.
78**SB
Note 2
Note 1: The “* * ” in the each product number is replaces with the output voltage of each product.
Note 2: A line under a Lot No. identifies the indication of product Labels.
Not underlined: [[Pb]]/INCLUDES > MCV
Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]]
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS
compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27
January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
The product(s) in this document (“Product”) contain functions intended to protect the Product from
temporary small overloads such as minor short-term overcurrent or overheating. The protective
functions do not necessarily protect Product under all circumstances. When incorporating Product into
your system, please design the system (1) to avoid such overloads upon the Product, and (2) to shut
down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For
details, please refer to the notes appearing below in this document and other documents referenced in
this document.
1 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
Equivalent Circuit
TA7805SB
TA78057SB
TA7806SB
TA7807SB
TA7808SB 35
TA7809SB
Input voltage VIN V
TA7810SB
TA7812SB
TA7815SB
TA7818SB
TA7820SB 40
TA7824SB
Output current I OUT 1 A
Power dissipation (Ta = 25°C) PD 1.8 W
Operating temperature Topr −30 to 85 °C
Storage temperature Tstg −55 to 150 °C
Junction temperature Tj 150 °C
junction to
Thermal resistance Rth (j-a) 69.4 °C/W
ambient
Note 3: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
2 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7805SB
Electrical Characteristics
(Unless otherwise specified, VIN = 10 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 4.8 5.0 5.2 V
7.0 V ≤ VIN ≤ 25 V ― 3 100
Line regulation Reg·line 1 Tj = 25°C mV
8.0 V ≤ VIN ≤ 12 V ― 1 50
5 mA ≤ IOUT ≤ 1.0 A ― 15 100
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 5 50
7.0 V ≤ VIN ≤ 20 V,
Output voltage VOUT 1 Tj = 25°C 4.75 ― 5.25 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.2 8.0 mA
7.0 V ≤ VIN ≤ 25 V,
Quiescent current change ΔIB 1 ― ― 1.3 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 50 ― μVrms
IOUT = 50 mA
f = 120 Hz, 8.0 V ≤ VIN ≤ 18 V,
Ripple rejection R.R. 3 62 78 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.6 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −0.6 ― mV/°C
coefficient of output voltage
TA78057SB
Electrical Characteristics
(Unless otherwise specified, VIN = 10.7 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 5.47 5.7 5.93 V
7.7 V ≤ VIN ≤ 25 V ― 4 110
Line regulation Reg·line 1 Tj = 25°C mV
8.7 V ≤ VIN ≤ 12.7 V ― 2 55
5 mA ≤ IOUT ≤ 1.0 A ― 15 110
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 5 55
7.7 V ≤ VIN ≤ 20.7 V,
Output voltage VOUT 1 Tj = 25°C 5.42 ― 5.98 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
7.7 V ≤ VIN ≤ 25 V,
Quiescent current change ΔIB 1 ― ― 1.3 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 55 ― μVrms
IOUT = 50 mA
f = 120 Hz, 8.8 V ≤ VIN ≤ 18.8 V,
Ripple rejection R.R. 3 62 77 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.5 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −0.7 ― mV/°C
coefficient of output voltage
3 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7806SB
Electrical Characteristics
(Unless otherwise specified, VIN = 11 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 5.75 6.0 6.25 V
8.0 V ≤ VIN ≤ 25 V ― 4 120
Line regulation Reg·line 1 Tj = 25°C mV
9 V ≤ VIN ≤ 13 V ― 2 60
5 mA ≤ IOUT ≤ 1.0 A ― 15 120
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 5 60
8 V ≤ VIN ≤ 21 V,
Output voltage VOUT 1 Tj = 25°C 5.7 ― 6.3 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
8.0 V ≤ VIN ≤ 25 V,
Quiescent current change ΔIB 1 ― ― 1.3 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 55 ― μVrms
IOUT = 50 mA
f = 120 Hz, 9 V ≤ VIN ≤ 19 V,
Ripple rejection R.R. 3 61 77 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.5 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −0.7 ― mV/°C
coefficient of output voltage
TA7807SB
Electrical Characteristics
(Unless otherwise specified, VIN = 12 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 6.72 7.0 7.28 V
9 V ≤ VIN ≤ 25 V ― 5 140
Line regulation Reg·line 1 Tj = 25°C mV
10 V ≤ VIN ≤ 14 V ― 2 70
5 mA ≤ IOUT ≤ 1.0 A ― 15 140
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 5 70
9 V ≤ VIN ≤ 22 V,
Output voltage VOUT 1 Tj = 25°C 6.65 ― 7.35 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
9 V ≤ VIN ≤ 25 V,
Quiescent current change ΔIB 1 ― ― 1.3 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 60 ― μVrms
IOUT = 50 mA
f = 120 Hz, 10 V ≤ VIN ≤ 20 V,
Ripple rejection R.R. 3 59 75 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.3 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −0.8 ― mV/°C
coefficient of output voltage
4 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7808SB
Electrical Characteristics
(Unless otherwise specified, VIN = 14 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 7.7 8.0 8.3 V
10.5 V ≤ VIN ≤ 25 V ― 6 160
Line regulation Reg·line 1 Tj = 25°C mV
11 V ≤ VIN ≤ 17 V ― 2 80
5 mA ≤ IOUT ≤ 1.0 A ― 12 160
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 80
10.5 V ≤ VIN ≤ 23 V,
Output voltage VOUT 1 Tj = 25°C 7.6 ― 8.4 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
10.5 V ≤ VIN ≤ 25 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 70 ― μVrms
IOUT = 50 mA
f = 120 Hz, 11.5 V ≤ VIN ≤ 21.5 V,
Ripple rejection R.R. 3 58 74 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.1 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −1.0 ― mV/°C
coefficient of output voltage
TA7809SB
Electrical Characteristics
(Unless otherwise specified, VIN = 15 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 8.64 9.0 9.36 V
11.5 V ≤ VIN ≤ 26 V ― 7 180
Line regulation Reg.line 1 Tj = 25°C mV
13 V ≤ VIN ≤ 19 V ― 2.5 90
5 mA ≤ IOUT ≤ 1.0 A ― 12 180
Load regulation Reg.load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 90
11.5 V ≤ VIN ≤ 24 V,
Output voltage VOUT 1 Tj = 25°C 8.55 ― 9.45 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
11.5 V ≤ VIN ≤ 26 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 75 ― μVrms
IOUT = 50 mA
f = 120 Hz, 12.5 V ≤ VIN ≤ 22.5 V,
Ripple rejection R.R. 3 56 72 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 1.0 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −1.1 ― mV/°C
coefficient of output voltage
5 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7810SB
Electrical Characteristics
(Unless otherwise specified, VIN = 16 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 9.6 10.0 10.4 V
12.5 V ≤ VIN ≤ 27 V ― 8 200
Line regulation Reg·line 1 Tj = 25°C mV
14 V ≤ VIN ≤ 20 V ― 2.5 100
5 mA ≤ IOUT ≤ 1.0 A ― 12 200
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 100
12.5 V ≤ VIN ≤ 25 V,
Output voltage VOUT 1 Tj = 25°C 9.5 ― 10.5 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
12.5 V ≤ VIN ≤ 27 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 80 ― μVrms
IOUT = 50 mA
f = 120 Hz, 13.5 V ≤ VIN ≤ 23.5 V,
Ripple rejection R.R. 3 55 72 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.9 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −1.3 ― mV/°C
coefficient of output voltage
TA7812SB
Electrical Characteristics
(Unless otherwise specified, VIN = 19 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 11.5 12.0 12.5 V
14.5 V ≤ VIN ≤ 30 V ― 10 240
Line regulation Reg·line 1 Tj = 25°C mV
16 V ≤ VIN ≤ 22 V ― 3 120
5 mA ≤ IOUT ≤ 1.0 A ― 12 240
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 120
14.5 V ≤ VIN ≤ 27 V,
Output voltage VOUT 1 Tj = 25°C 11.4 ― 12.6 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA
14.5 V ≤ VIN ≤ 30 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 90 ― μVrms
IOUT = 50 mA
f = 120 Hz, 15 V ≤ VIN ≤ 25 V,
Ripple rejection R.R. 3 55 71 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.7 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −1.6 ― mV/°C
coefficient of output voltage
6 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7815SB
Electrical Characteristics
(Unless otherwise specified, VIN = 23 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 14.4 15.0 15.6 V
17.5 V ≤ VIN ≤ 30 V ― 11 300
Line regulation Reg·line 1 Tj = 25°C mV
20 V ≤ VIN ≤ 26 V ― 3 150
5 mA ≤ IOUT ≤ 1.0 A ― 12 300
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 150
17.5 V ≤ VIN ≤ 30 V,
Output voltage VOUT 1 Tj = 25°C 14.25 ― 15.75 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.4 8.0 mA
17.5 V ≤ VIN ≤ 30 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 110 ― μVrms
IOUT = 50 mA
f = 120 Hz, 18.5 V ≤ VIN ≤ 28.5 V,
Ripple rejection R.R. 3 54 70 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.5 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −2.0 ― mV/°C
coefficient of output voltage
TA7818SB
Electrical Characteristics
(Unless otherwise specified, VIN = 27 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 17.3 18.0 18.7 V
21 V ≤ VIN ≤ 33 V ― 13 360
Line regulation Reg·line 1 Tj = 25°C mV
24 V ≤ VIN ≤ 30 V ― 4 180
5 mA ≤ IOUT ≤ 1.0 A ― 12 360
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 180
21 V ≤ VIN ≤ 33 V,
Output voltage VOUT 1 Tj = 25°C 17.1 ― 18.9 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.5 8.0 mA
21 V ≤ VIN ≤ 33 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 125 ― μVrms
IOUT = 50 mA
f = 120 Hz, 22 V ≤ VIN ≤ 32 V,
Ripple rejection R.R. 3 52 68 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.4 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −2.5 ― mV/°C
coefficient of output voltage
7 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
TA7820SB
Electrical Characteristics
(Unless otherwise specified, VIN = 29 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 19.2 20.0 20.8 V
23 V ≤ VIN ≤ 35 V ― 15 400
Line regulation Reg·line 1 Tj = 25°C mV
26 V ≤ VIN ≤ 32 V ― 5 200
5 mA ≤ IOUT ≤ 1.0 A ― 12 400
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 200
23 V ≤ VIN ≤ 35 V,
Output voltage VOUT 1 Tj = 25°C 19.0 ― 21.0 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.6 8.0 mA
23 V ≤ VIN ≤ 35 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 135 ― μVrms
IOUT = 50 mA
f = 120 Hz, 24 V ≤ VIN ≤ 34 V,
Ripple rejection R.R. 3 50 66 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.4 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −3.0 ― mV/°C
coefficient of output voltage
TA7824SB
Electrical Characteristics
(Unless otherwise specified, VIN = 33 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 23.0 24.0 25.0 V
27 V ≤ VIN ≤ 38 V ― 18 480
Line regulation Reg·line 1 Tj = 25°C mV
30 V ≤ VIN ≤ 36 V ― 6 240
5 mA ≤ IOUT ≤ 1.0 A ― 12 480
Load regulation Reg·load 1 Tj = 25°C mV
250 mA ≤ IOUT ≤ 750 mA ― 4 240
27 V ≤ VIN ≤ 38 V,
Output voltage VOUT 1 Tj = 25°C 22.8 ― 25.2 V
5.0 mA ≤ IOUT ≤ 1.0 A
Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.6 8.0 mA
27 V ≤ VIN ≤ 38 V,
Quiescent current change ΔIB 1 ― ― 1.0 mA
IOUT = 5 mA, Tj = 25°C
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,
Output noise voltage VNO 2 ― 150 ― μVrms
IOUT = 50 mA
f = 120 Hz, 28 V ≤ VIN ≤ 38 V,
Ripple rejection R.R. 3 50 66 ― dB
IOUT = 50 mA, Tj = 25°C
Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V
Short circuit current limit ISC 1 Tj = 25°C ― 0.3 ― A
Average temperature
TCVO 1 IOUT = 5 mA ― −3.5 ― mV/°C
coefficient of output voltage
8 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
Test Circuit 1 / Standard Application Circuit
Test Circuit 2
VNO
Test Circuit 3
R.R.
9 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
Usage Precautions
(1) In regard to GND, be careful not to apply a negative voltage to the input/output terminal.
(2) If a surge voltage exceeding the absolute maximum rating is applied to the input terminal or if a
voltage in excess of the input terminal voltage is applied to the output terminal, the circuit may be
destroyed.
Particular care is necessary in the case of the latter.
Circuit destruction may also occur if the input terminal shorts to GND in a state of normal operation,
causing the output terminal voltage to exceed the input voltage (GND potential) and the electrical
charge of the chemical capacitor connected to the output terminal to flow into the input side.
Where these risks exist, take steps such as connecting zener and general silicon diodes to the circuit,
as shown in the figure below.
(3) When the input voltage is too high, the power dissipation of the three-terminal regulator, which is a
series regulator, increases, causing the junction temperature to rise. In such a case, it is
recommended to reduce the power dissipation, and hence the junction temperature, by inserting a
power-limiting resistor RSD in the input terminal.
Reducing VIN' below the lowest voltage necessary for the IC will cause ripple, deterioration in output
regulation and, in certain circumstances, parasitic oscillation.
To determine the resistance value of RSD, design with a margin, referring to the following equation.
(4) Be sure to connect a capacitor near the input terminal and output terminal between both terminals
and GND. The capacitances should be determined experimentally because they depend on PCB
patterns. In particular, adequate investigation should be made to ensure there is no problem even in
high or low temperatures
10 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
• Low voltage
Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product’s
protective functions will not operate properly and the Product may be permanently damaged.
• Overcurrent Protection
The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor
overcurrent of brief duration. When the overcurrent protective function in the Product activates,
immediately cease application of overcurrent to Product. Improper usage of Product, such as application of
current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit
not to operate properly and/or damage Product permanently even before the protection circuit starts to
operate.
11 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
12 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
13 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
14 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
Package Dimensions
SIP3-P-2.50A Unit: mm
15 2010-06-21
TA7805,057,06,07,08,09,10,12,15,18,20,24SB
16 2010-06-21