ISO IEC 17025 Accreditation Cert+Scope-GCC Accreditation

Accreditation Procedures
GAC
10.15 Scope of Accreditation

ACCREDITED
Issue No: 1/ Issue Date: 09-12-2019
File Manager: Hamza Khan CALIBRATION
ISO/IEC 17025:2017
No. ACL 0014
Calibration Laboratory
Accreditation No. ACL 0014
is accredited by the GCC Accreditation Center (GAC) in accordance with the recognized International Standard ISO/IEC 17025:2017, “General
requirements for the competence of testing and calibration laboratories”
Arabian Calibration Dev. Rep. Co. LLC (ARABCAL)
Contact: Mr. Eby Joy

Address. Industrial Area 13, Near Rameez Hyper Market, Along E311 Tel: +971 6 5345747/+971 552210154
Road, Sharjah, UAE Fax: +971 6 5345727
PO Box: 24650 Email: [email protected]
Web Address: www.arabcal.com
Locations where calibration activities covered by the above Accreditation Standard are undertaken
1- Industrial Area 13, Near Rameez Hyper Market, Along E311 Road, Sharjah, UAE
For the following scope:
Scope:
Version: 1.4 Page 1 of 21

Date: 24th July 2019
Approved by: Atta Subhan
GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Scope details are as follows:
1. Calibration
1.25 Torque measuring devices
.02 Torque transducers
1.26 Testing machines
.01 Tension and universal machines in tension
.02 Compression and universal machines in compression
1.23 Force measuring devices
.05 Force gauges
1.20 Pressure and vacuum measuring devices
.01 Pressure gauges
.02 Vacuum gauges (bourdon tube)
1.03 Engineering metrology equipment
.01 Surface plates
.06 Bevel protractors
.13 Thread measuring accessories
.21 Micrometer heads
.22 External micrometers
.24 Depth micrometers
.25 Electronic indicators, dial gauges and test indicators
.26 Bore gauges
.27 Electronic and Vernier calipers
.28 Electronic and Vernier height and depth gauges
.29 Feeler gauges
GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
.31 Steel rules and measuring tapes
1.90 Acoustic measuring and calibration equipment

.02 Sound level meters
Calibration field 1: (Force)

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Method Type of Instrument or Permanent lab (P)

CMC Expressed as an Expanded
Measurand Measuring Range (standard/guide + internal Material
Uncertainty (k = 2) ** / Client-site (S) *
procedure)
0.5 Nm to 338.95 Nm 0.5%
> 338.95 Nm to 813.49
0.5% Torque
Torque Measuring Devices Nm BS 7882+ CI/06/TT1 P
Testers/Transducers
>813.49 Nm to 2711.63
0.5%
Nm
Force Measurement VDI/VDE 2624 part 2.1 + Push pull
50 N to 4 kN 0.2% P
(Compression/Tension) CI/04/FG1 Gauge/Force Gauge
Testing Machines 4 kN to 45 kN 0.4% Universal Testing S
(Compression/Tension) ISO 7500 + CI/09/TTM1
> 45 kN to 245 kN 0.5% Machine
Force Measuring 4 kN to 45 kN 0.4% CI/09/L1 Dynamometers S

Instruments(Dynamometers) > 45 kN to 245 kN 0.5%
Manufacturer
Cable Tensiometers 0.5 N to 1.5 kN 0.2% procedure+ Cable Tensiometers
CI/09/CTSM1 P
Calibration field 2: (Pressure)

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
0 to 1.2 bar 0.5 mbar DKD-R 6-1 + CI/02/PI2
Absolute pressure 0.7 mbar (Using Pressure P
> 1.2 bar to 3.2 bar Modules and station)
- 25 mbar to 25 mbar 0.02 mbar Indicators, P
-1 bar to 2 bar 0.30 mbar DKD-R 6-1 + CI/02/PI2 Transducers, P
(Using High Precision Transmitters,
> 2 bar to 20 bar 9 mbar Controllers, Pressure switches P
Gauge pressure -Pneumatic
> 20 bar to 210 bar 25 mbar Modules, portable P
controllers)
-1 bar to 2.5 bar 1 mbar P/S
Upto 200 bar 30 mbar P/S
1 bar to 60 bar 0.03% DKD-R 6-1 + CI/01/PI2 Indicators, P
(Using Dead weight Transducers,
Gauge Pressure -Hydraulic
> 60 bar to 1200 bar 0.04% Tester) Transmitters,
switches
Gauge Pressure -Hydraulic DKD-R 6-1 + CI/01/PI2 Indicators, P/S
0.1 bar (Using Pressure Transducers,
1 bar to 700 bar Modules, portable Transmitters,
controllers, Reference switches
Indicators)

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Calibration field 2: (Dimensional)

procedure)
0 mm to 300 mm 20 μm
Calipers (All Types) LC: 0.01 Vernier, Dial, Digital
>300 mm to 600 mm 30 μm ISO 13385-1 + CI/05/V3 P
mm calipers
>600 mm to 1000 mm 40 μm
0 to 100 mm 2 μm
Outside Micro-meter LC:
>100 mm to 200 mm 2.5 μm
0.001 mm
>200 mm to 300 mm 3.3 μm Analogue, Digital
ISO 3611 + CI/05/O2 P
> 300 mm to 400 mm 10 μm micrometer
LC: 0.01 mm > 400 mm to 600 mm 10 μm
> 600 mm to 1000 mm 20 μm
Dial Indicators (Type A, Type
BS 907, ANSI B89.1.10M Plunger, Lever type
B, Type C) 0 to100 mm 3 µm P
and BS 2795 + CI/05/D6 Dial Indicators
LC:0.001mm
Micro-meter heads Analogue, Digital
0 to 50 mm 1.7 µm IS 9843 + CI/05/MH1 P
LC:0.001 mm micrometer heads
Digital/Dial Thickness gauge
0 to 50 mm 3 µm CI/09/CTG1 Thickness Gauge P
LC: 0.001 mm
Ultrasonic thickness gauge Ultrasonic thickness
0 to 300 mm 4.0 μm
L.C : 0.01 mm CI/09/CTG1 gauge P
LC: 0. 1 mm 0 to 300 mm 10 μm

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Calibration field 2: (Dimensional)(Continuation)

procedure)
Depth Micro-meter BS 6468 + CI/05/DMM1 Analogue, Digital Depth
0 to 300 mm 7 μm
LC:0.001 mm micrometer P
LC:0.01 mm 0 to 300 mm 10 μm
Depth Gauge/Caliper
0 to 400 mm 10 μm BS 6365 + CI/05/DV1 Depth Gauge/Caliper P
LC:0.01mm
Electronic/Dial/Vernier- 0 to 600 mm 4 μm
Height Gauge Electronic/Dial/Vernier-
LC:0.0001mm 0 to 1000 mm 7 μm IS 2921 + CI/05/HG1 P
Height Gauge
LC:0.001 mm 0 to 600 mm 6 µm
LC:0.01 mm 0 to 1000 mm 10 µm
0 to 300 mm 3.5 µm
Setting Rods CI/05/O2 Setting Rods P
>300 mm to 600 mm 5 µm
Feeler Gauge set 0.025 mm to 2 mm 2.0 µm BS 957 + CI/01/FGE1 Feeler Gauge P
0-500 μm, 0-1500 μm, 2.0 μm DeFelsko Guideline+ Coating thickness gauge
Coating thickness gauge P
0-5 mm, 0-30 mm CI/09/CTG1
DeFelsko Guideline+
Test Foils 0 μm to 2000 μm 2.0 μm Test Foils P
CI/09/CTG1

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
Dial Indicator calibrator 1.0 μm
0 to 25 mm
LC:0.0002 mm Dial Indicator
P/S
CI/05/D6 calibrator
>25 mm to 50 mm 1.9 μm
Cylindrical Measuring Pin / EURAMET cg-06 + Pin Gauge (Go-No Go

0.4 mm to 15 mm 1.5 µm P
Thread Measuring Wire Pin CI/05/PG1 Gauge)
0.5 mm Ø 100 mm 1.8 µm
Above Ø 100 mm to 200 EURAMET cg-06 + Plug Gauge
Plain / Setting Plug Gauges 2.8 µm CI/05/PG1 P
mm
Above Ø 200 mm to 300
3.2 µm
mm
Radius Gauge 0.6 mm to 25 mm 7.0 µm IS 5273 + CI/05/RADG-1 Radius Gauge P
Bevel Protractor
0, 30, 45, 90° 2.0 minutes of arc IS 4239 + CI/05/BPR1 Bevel Protractor P
LC: 0.01°
160mm x 100mm to Granite surface
Surface plate 6 µm BS 817 + CI/05/CST1 P
1600mm x 1000mm plate/cast iron plate

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
0.032 mm to 5.00 mm
6.3 μm IS 460-1 &2 +
(Wiremesh)
Test Sieve P
5.00 mm to 50 mm CI/05/TS1
Test Sieve 13 μm
(Wiremesh)
1 mm to 125 mm
41 μm
(Perforated)
Tape / Scale Calibrators Manufacturer Tape / Scale
Upto 1000 mm 20 µm P/O
L.C.: 0.001 mm procedure+ CI/05/M1 Calibrators
Magnification error:
0.80%
10X to 100X
Linear Measurement Optical
Optical Comparator X-Axis :140 mm, 2 mm JIS B 7184 + CI/01/OC1 Comparator/Profile P/O
Y axis : 80 mm Projectors
Angle measurement: 2 minutes of arc
1 to 360°
Measuring Tape 0 m to 5 m 2 mm Measuring Tape/Pie
IS 1269 + CI/05/M1 P
LC: 1 mm > 5 m to 30 m 5 mm Tape
Steel Rule LC 0.5 mm 0 m to 1 m 20 µm IS 1269 + CI/05/M1 Steel Rule P

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
0 to 25 mm 1.8 µm
25 mm to 50 mm 2.0 µm
>50 mm to 75 mm 2.5 µm
>75 mm to 100 mm 2.8 µm
Inside micro-meter Inside micro-meter
>100 mm to 150 mm 3.0 µm BS 959 + CI/05/IM2 P
L.C.: 0.01 mm (Stick/Tubular)
>150 mm to 300 mm 5.0 µm
>300 mm to 400 mm 6.8 µm
>400 mm to 600 mm 9 µm
>600 mm to 1000 mm 16 µm
Inside Micro-meter (Caliper
Inside Micro-meter
type) 0 to 250 mm 5 µm BS 959 + CI/05/IM2 P
(Caliper type)
LC: 001 mm
Three point micro-meter Three Point
0 to 250 mm 5.0 µm CI/05/IM2 P
LC: 001 mm Micrometer

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
Bore Gauge (Transmission Upto 2 mm 2.4 μm JIS B 7515 + Telescopic Gauge,
error only)Span Dia. Upto P
CI/05/BG1 Bore Gauge
400 mm LC 0.001 mm
1 mm to 100 mm 1 μm
ANSI B89.1.6 + Ring Gauge
Cylindrical Setting Standard P
CI/05/RG1
>100 mm to 250 mm 2.5 μm
Calibration field 3: (Acoustics)

procedure)
Sound Level-Generation 94 dB & 114 dB 0.32 dB BS 7580-1 + CI/05/SLM1 Sound Level Meters P/S

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Calibration field 4: (Electrical)

procedure)
Oscilloscope
2 mV to 50 V 0.3%
(50Ω and 1MΩ) Amplitude CI/01/OSE1 Based on Multiproduct
P/S
Time Base 2 ns to 5 s 0.5% EURAMET cg-7 Calibrator
Bandwidth 50 kHz to 1 GHz 4.5%
DC Power 33 mV to 1000 V CI/01/M1 Based on
EURAMET cg-15 Multiproduct
0.33 mA to 2.999 A 10.9 μW to 2.9 kW 0.04% P/S
Calibrator
3 A to 20 A 99 mW to 20 kW 0.12%
AC Power @ UPF 33 mV to 1000 V (45 Hz to 65 Hz)
3.3 mA to 8.999 mA 0.11 mW to 2.97 mW 0.20%
2.97 mW to 8.99 W 0.23%
9 mA to 32.99 mA 0.29 mW to 11 mW 0.17%
11 mW to 32.99 W 0.17% Multiproduct
CI/01/M1 P/S
Calibrator
33 mA to 89.99mA 1.1 mW to 29.7 mW 0.20%
29.7 mW to 89.9 W 0.24%
90 mA to 329.99 mA 2.97 mW to 109.9 mW 0.13%
109.9 mW to 329.99 W 0.17%

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Calibration field 4: (Electrical)(Continuation)
Method Permanent lab (P)

Measurand Measuring Range (standard/guide + internal Type of Instrument or / Client-site (S) *
Uncertainty (k = 2) ** Material
procedure)
0.33 A to 0.8999 A 10.9 mW to 297 mW 0.18%
297 mW to 899.9 W 0.21%
0.9 A to 2.1999 A 2.97 mW to 725 mW 0.18%
725 mW to 2.1 kW 0.18% CI/01/M1 Multiproduct P/S
2.2 A to 4.4999 A 72.6 mW to 1.485 W 0.20% Calibrator
1.485 W to 4.4 kW 0.22%
4.5 A to 20 A 148.5 mW to 6.6 W 0.17%
6.6 W to 20 kW 0.19%
Phase angle Voltage to current
0-90° 10 Hz to 65 Hz 0.2°
65 Hz to 500 Hz 0.4° Multiproduct
CI/01/M1 P/S
0.5 kHz to 1kHz 0.8° Calibrator
>90° to 360° 50 Hz 0.4°

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

CMC Expressed as an Expanded Type of Instrument or
Measurand Measuring Range (standard/guide + internal Material / Client-site (S) *
Uncertainty (k = 2) **
procedure)
40 - 65 Hz; 30 - 500 V
PF= 1 to 0.5 0.07%
(Lead and Lag) CI/01/EM1 Based on Energy Meter
Active & Reactive Energy Current: 1 mA to 12 A Standard-Emsyst P/S
EN50470
40 - 65 Hz; 30 - 500 V
PF= 1 to 0.5 0.08%
(Lead and Lag)
Current: 10 mA to 120 A
Generation - Resistance 10 µΩ 1.5%
50 µΩ 1.2%
200 µΩ 0.07%
Standard
500 µΩ 0.06%
CI/01/M1 Based on Resistance(s)
1 mΩ 0.06% EURAMET cg-15 P/S
Multiproduct
2 mΩ 0.08%
Calibrator
5 mΩ 0.06%
50 mΩ 0.06%
100 mΩ 0.02%

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
200 mΩ 0.04%
500 mΩ 0.02%
1Ω 0.02%
>1 Ω - 10 Ω 0.006%
Multiproduct
>10 Ω - 100 Ω 0.005% Calibrator
CI/01/M1 Based on
>100 Ω - 1MΩ 0.004% Standard P/S
Generation - Resistance EURAMET cg-15
>1 MΩ - 3.3 MΩ 0.007% Resistance(s)
>3.3 MΩ - 11 MΩ 0.02%
>11 MΩ - 33 MΩ 0.03%
>33 MΩ - 110 MΩ 0.06%
>110 MΩ - 330 MΩ 0.3%
>330 MΩ - 1 GΩ 1.7%

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
Generation – Capacitance 100 pF – 1 nF 4.7% to 1.5% Standard Capacitance

CI/01/M1 P/S
1 nF - 10 µF 1.2% to 1.5% Box
Generation - Capacitance 0.19 nF to 0.3999 nF 6.7%

0.4 nF to 1.0999 nF 3.9%
1.1 to 3.2999 nF 2.5%
3.3 to 10.9999 nF 0.5%
11 to 32.9999 nF 0.9%
CI/01/M1 Multiproduct P/S
33 to 109.999 nF 0.5% Calibrator
110 to 329.999 nF 0.5%
0.33 to 1.09999 μF 0.5%
1.1 to 3.29999 μF 0.5%
3.3 to 10.9999 μF 0.5%
11 to 32.9999 μF 0.7%

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
Generation - Capacitance 33 to 109.999 μF 0.7%
110 to 329.999 μF 0.7%
0.33 mF to 1.09999 mF 0.9%
CI/01/M1 Multiproduct P/S
1.1 to 3.29999 mF 0.7% Calibrator
3.3 to 10.9999 mF 0.7%
11 to 32.9999 mF 1.0%
33 to 110 mF 1.4%
Multiproduct
Calibrator
Generation - Inductance 1 mH to 10 H 1% CI/01/M1 P/S
Standard Capacitance
Box
Measurement-Resistance 1 mΩ to 100 MΩ 300 nΩ - 230 ppm Master LCR Meter
CI/01/EC1
Measurement-Capacitance 1 pF to 1 F 20 ppm - 90 ppm P/S
Measurement- Inductance 10 nH to 100 kH 0.10%

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
Safety Testers
Earth Bond Resistance 36 mΩ to 1 Ω 5 mΩ to 11 mΩ
5Ω 29 mΩ Electrical Test
CI/01/SA1 Based on
equipment Calibrator P
10 Ω 58 mΩ Transmille 3200 Manual
100 Ω 580 mΩ
1000 Ω 5.8 Ω
100 mA 9 mA Electrical Test
Earth bond current @ 0.1Ώ CI/01/SA1 Based on
equipment Calibrator P
load @ 50 Hz 4 A - 25 A 0.5 A Transmille 3200 Manual
2.2 mA 40 μA Electrical Test
PAT Leakage current @ 240 CI/01/SA1 Based on
4.7 mA 80 μA equipment Calibrator P
V Transmille 3200 Manual
7.7 mA 140 μA
Electrical Test
CI/01/SA1 Based on
Load for PAT @ UAE Mains 0.13 kVA 6% equipment Calibrator P
Transmille 3200 Manual
0.2 Ω - 2 Ω 30 mΩ Electrical Test
CI/01/SA1 Based on equipment Calibrator
Continuity Resistance 2 Ω - 10 Ω 40 mΩ - 58 mΩ P
10 Ω - 20 Ω 58 mΩ - 90 mΩ

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014

procedure)
100 Ω 0.32 Ω Electrical Test

CI/01/SA1 Based on equipment Calibrator
Continuity Resistance P
1 kΩ 3Ω Transmille 3200 Manual
0.51 Ω 43 mΩ
1Ω 44 mΩ Electrical Test
CI/01/SA1 Based on
Loop impedance 5Ω 56 mΩ equipment Calibrator P
10 Ω 80 mΩ
99 Ω 590 mΩ
994 Ω 5.8 Ω
Calibration field 5: (Time & Frequency)

procedure)
Time & Frequency
CI/05/SW1 Based on Signal Generator,

Time Interval 5 s to 86400 s 0.3 s universal Frequency P/S
NIST 960-12
counter

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
Calibration field 5: (Time & Frequency)(Continuation)

procedure)
Multi Product
CI/01/TCM1 Based on Calibrator, Frequency
P/S
Rotational Speed-Generation 30 rpm to 200000 rpm 0.02% SANAS TR-45-02 Generator
CI/05/CFG1 Based on
30 rpm to 60000 rpm 1 rpm Master Tachometer P/S
Rotational Speed-Measure SANAS TR-45-02
*: Put only ‘P’, ‘S’ or ‘P and S’

**Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can
achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or
nearly ideal measuring equipment. CMC’s represent expanded uncertainties expressed at approximately the 95 % level of confidence,
usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may
be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific
calibration.
Note: the text in blue indicates the new scope OR update in the Edition of a method in this issue of the scope of accreditation.
Log of Suspended Scopes:

GAC

ACCREDITED
ISO/IEC 17025:2017
No. ACL 0014
CMC Expressed as an Method Type of Instrument Permanent lab (P) Date Date
Measurand Measuring Range Expanded (standard/guide + or Material Suspended Reinstated
/ Client-site (S) *
Uncertainty (k = 2) ** internal procedure)
Log of Withdrawn Scopes:

CMC Expressed as an Method Type of Instrument or Permanent lab (P) Date
Measurand Measuring Range Expanded Uncertainty (standard/guide + internal Material Withdrawn
/ Client-site (S) *
(k = 2) ** procedure)
END
This conformity assessment body (CAB) is recorded as issuing GAC accredited certificates to organizations in the countries listed below. This list is current
at the time of issue of this schedule.
United Arab Emirates Bahrain Saudi Arabia Oman Qatar Kuwait Yemen


ISO IEC 17025 Accreditation Cert+Scope-GCC Accreditation

Uploaded by

Copyright:

Available Formats

ISO IEC 17025 Accreditation Cert+Scope-GCC Accreditation

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ISO IEC 17025 Accreditation Cert+Scope-GCC Accreditation

Uploaded by

Copyright:

Available Formats

What is the scope of accreditation for?

What is the scope of accreditation for?

What calibration fields are covered?

What calibration fields are covered?

Accreditation Procedures

10.15 Scope of Accreditation

Arabian Calibration Dev. Rep. Co. LLC (ARABCAL)

Contact: Mr. Eby Joy

For the following scope:

Version: 1.4 Page 1 of 21

10.15 Scope of Accreditation

Scope details are as follows:

10.15 Scope of Accreditation

.31 Steel rules and measuring tapes

1.90 Acoustic measuring and calibration equipment

Calibration field 1: (Force)

Version: 1.4 Page 3 of 21

10.15 Scope of Accreditation

Method Type of Instrument or Permanent lab (P)

Force Measuring 4 kN to 45 kN 0.4% CI/09/L1 Dynamometers S

Calibration field 2: (Pressure)

Version: 1.4 Page 4 of 21

10.15 Scope of Accreditation

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 5 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)

Version: 1.4 Page 6 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)(Continuation)

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 7 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)(Continuation)

Method Type of Instrument or Permanent lab (P)

Cylindrical Measuring Pin / EURAMET cg-06 + Pin Gauge (Go-No Go

Version: 1.4 Page 8 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)(Continuation)

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 9 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)(Continuation)

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 10 of 21

10.15 Scope of Accreditation

Calibration field 2: (Dimensional)(Continuation)

Method Type of Instrument or Permanent lab (P)

Calibration field 3: (Acoustics)

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 11 of 21

10.15 Scope of Accreditation

Calibration field 4: (Electrical)

Method Type of Instrument or Permanent lab (P)

Version: 1.4 Page 12 of 21

10.15 Scope of Accreditation

Calibration field 4: (Electrical)(Continuation)

Method Permanent lab (P)

>90° to 360° 50 Hz 0.4°

Version: 1.4 Page 13 of 21