Design of Synchronous Machines

Design of Synchronous
Machines
DR. PRIYANKA PALIWAL
ELECTRICAL ENGINEERING DEPARTMENT, MANIT, BHOPAL
Classification
Salient Pole Cylindrical Rotor
(Turbo Alternator)
Driven by water wheels or diesel engines Driven by steam turbines and gas turbines
Operate at low speeds Operate at high speeds
large number of poles is required to produce desired frequency Since speed is high, it has cylindrical structure with
slots
Salient pole has projecting poles and field coils mounted

Maximum speed of Turbo alternators is 3000 rpms with
on the poles
two poles at 50 Hz
Design Framework
Synchronous machines are designed to obtain the following information’s.
(i) Main dimensions of the stator frame.
(ii) Complete details of the stator windings.
(iii) Design details of the rotor and rotor winding.
(iv) Performance details of the machine.
To proceed with the design and arrive at the design information the design engineer needs the
following information.
(i) Specifications of the synchronous machine.
(ii) Information regarding the choice of design parameters
Specifications of the synchronous machine:
Important specifications required to initiate the design procedure are as follows:

➢Rated output of the machine in kVA or MVA,
➢Rated voltage of the machine in kV, Speed,
➢frequency, type of the machine generator or motor,
➢Type of rotor salient pole or non salient pole,
➢connection of stator winding,
➢limit of temperature,
➢details of prime mover.
Main Dimensions:
Internal diameter and gross length of the stator forms the main dimensions of the machine.
In order to obtain the main dimensions it is required to develop the relation between the output
and the main dimensions of the machine. This relation is known as the output equation.
Where, Bav= Specific Magnetic Loading

q= Specific Electric Loading
Kw=Winding space factor= 0.955 for infinitely distributed full pitched winding
Factors affecting Choice of Specific Magnetic Loading
Bav
Iron Loss: A high value of flux density in the air gap leads to higher value of flux in the
iron parts of the machine which results in increased iron losses and reduced efficiency.
Voltage: When the machine is designed for higher voltage space occupied by the
insulation becomes more thus making the teeth smaller and hence higher flux density
in teeth and core.
Transient short circuit current: A high value of gap density results in decrease in
leakage reactance and hence increased value of armature current under short circuit
conditions.
Contd….
Stability: The maximum power output of a machine under steady state condition is indirectly proportional
to synchronous reactance. If higher value of flux density is used it leads to smaller number of turns per
phase in armature winding. This results in reduced value of leakage reactance and hence increased value
of power and hence increased steady state stability.
Parallel operation: The satisfactory parallel operation of synchronous generators depends on the
synchronizing power. Higher the synchronizing power higher will be the ability of the machine to operate
in synchronism.
Factors affecting Choice of Specific Electric
Loading q
Copper loss: Higher the value of q larger will be the number of armature of conductors which
results in higher copper loss. This will result in higher temperature rise and reduction in
efficiency.
Voltage: A higher value of q can be used for low voltage machines since the space required for
the insulation will be smaller.
Synchronous reactance: High value of q leads to higher value of leakage reactance and armature
reaction and hence higher value of synchronous reactance. Such machines will have poor
voltage regulation, lower value of current under short circuit condition and low value of steady
state stability limit and small value of synchronizing power.
Separation of D and L
➢Inner diameter and gross length of the stator can be calculated from from the output equation.
➢ To separate suitable relations are assumed between D and L depending upon the type of the generator.
For Salient Pole Machines
In case of salient pole machines either round or rectangular pole construction is employed. In these
types of machines the diameter of the machine will be quite larger than the axial length.
Round Poles: The ratio of pole arc to pole pitch may be assumed varying between 0.6 to 0.7 and pole arc
may be taken as approximately equal to axial length of the stator core. Hence Axial length of the core/
pole pitch = L/ p = 0.6 to 0.7
Rectangular poles: The ratio of axial length to pole pitch may be assumed varying between 0.8 to 3 and a
suitable value may be assumed based on the design specifications
Cylindrical Rotor
Thus, using above equations D and L can be calculated for Cylindrical Rotor/ Turbo Alternator
Effect of Short Circuit Ratio
1. Voltage regulation
2. Stability
3. Parallel operation
4. Short circuit Current
5. Cost and size of the machine
For salient pole machines SCR value varies from 0.9 to 1.3
For turbo alternators SCR value varies from 0.7 to 1.1
Length of the air gap
Length of the air gap is a very important parameter as it greatly affects the performance of the machine. Air
gap in synchronous machine affects the value of SCR and hence it influences many other parameters. Hence,
choice of air gap length is very critical in case of synchronous machines.
Advantages of Large Air gap:
(i) Stability: Higher value of stability limit
(ii) Regulation: Smaller value of inherent regulation
(iii) Synchronizing power: Higher value of synchronizing power
(iv) Cooling: Better cooling
(v) Noise: Reduction in noise
(vi) Magnetic pull: Smaller value of unbalanced magnetic pull
Contd….
Disadvantages of Large Air gap:
(i) Field MMF: Larger value of field MMF is required
(ii) Size: Larger diameter and hence larger size
(iii) Magnetic leakage: Increased magnetic leakage
(iv) Weight of copper: Higher weight of copper in the field winding
(v) Cost: Increase overall cost.
Step:1 Design of Stator Winding: No. of Slots
The number of slots are to be properly selected because the number of slots affect the cost and
performance of the machine. There are no rules for selecting the number of slots. But looking into
the advantages and disadvantages of higher number of slots, suitable number of slots per pole per
phase is selected. However the following points are to be considered for the selection of number of
slots.
Advantages of Large no. of slots:
(i) Reduced leakage reactance
(ii) Better cooling
(iii) Decreased tooth ripples
Design of Stator Winding: No. of Slots
Disadvantages of Large no. of slots:
(i) Higher cost
(ii) Teeth becomes mechanically weak
(iii) Higher flux density in teeth
For optimum design:
Slot pitch must be with in the following limitations
(i) Low voltage machines 3.5 cm
(ii) Medium voltage machines up to 6kV 5.5 cm
(iii) High voltage machines up to 15 kV 7.5 cm
Considering all the above points number of slots per pole phase for salient pole machines may be
taken as 3 to 4 and for turbo alternators it may be selected as much higher of the order of 7 to 9
slots per pole per phase
Step:2 Design of Stator Winding: No. of Turns/Phase
Turns per phase can be calculated from emf equation of the alternator.
Induced emf Eph = 4.44 f TphKw
Hence turns per phase Tph = Eph / 4.44 f Kw
Eph = induced emf per phase
Zph = no of conductors/phase in stator
Tph = no of turns/phase
kw = winding factor may assumed as 0.955
Step:3 Design of Stator Winding: Conductor Cross section
➢Area of cross section of stator conductors can be estimated from the stator current per phase
and suitably assumed value of current density for the stator windings.
➢Sectional area of conductor= Stator current/ Current density
➢Stator current can be calculated as:
Usual value of current density for stator windings is 3 to 5 amps/mm2.

Design of Synchronous Machines

Uploaded by

Copyright:

Available Formats

Design of Synchronous Machines

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design of Synchronous Machines

Uploaded by

Copyright:

Available Formats

What are the different types of synchronous machines classified based on their rotor structure?

What are the main specifications required for designing a synchronous machine?

Design of Synchronous

Operate at low speeds Operate at high speeds

Salient pole has projecting poles and field coils mounted

Important specifications required to initiate the design procedure are as follows:

Where, Bav= Specific Magnetic Loading

Usual value of current density for stator windings is 3 to 5 amps/mm2.

You might also like