Scribd Logo
Upload

Welcome to Scribd!

  • 66 views

    USART

    Uploaded by

    aesyop
    This document provides a configuration report for a USART project using an STM32F407 MCU. It details the pinout, clock tree, IPs including USART3 configured for asynchronous communication at 115200 baud, and NVIC configuration. Power consumption and software project settings are also specified.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    USART

    Uploaded by

    aesyop
    66 views9 pages
    This document provides a configuration report for a USART project using an STM32F407 MCU. It details the pinout, clock tree, IPs including USART3 configured for asynchronous communication at 115200 baud, and NVIC configuration. Power consumption and software project settings are also specified.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a configuration report for a USART project using an STM32F407 MCU. It details the pinout, clock tree, IPs including USART3 configured for asynchronous communication at 115200 baud, and NVIC configuration. Power consumption and software project settings are also specified.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    66 views9 pages

    USART

    Uploaded by

    aesyop
    This document provides a configuration report for a USART project using an STM32F407 MCU. It details the pinout, clock tree, IPs including USART3 configured for asynchronous communication at 115200 baud, and NVIC configuration. Power consumption and software project settings are also specified.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 9

    USART Project

    Configuration Report

    1. Description

    1.1. Project

    Project Name USART


    Board Name USART
    Generated with: STM32CubeMX 4.19.0
    Date 02/10/2017

    1.2. MCU

    MCU Series STM32F4


    MCU Line STM32F407/417
    MCU name STM32F407VETx
    MCU Package LQFP100
    MCU Pin number 100

    Page 1
    USART Project
    Configuration Report

    2. Pinout Configuration

    Page 2
    USART Project
    Configuration Report

    3. Pins Configuration

    Pin Number Pin Name Pin Type Alternate Label


    LQFP100 (function after Function(s)
    reset)
    6 VBAT Power
    10 VSS Power
    11 VDD Power
    14 NRST Reset
    19 VDD Power
    20 VSSA Power
    21 VREF+ Power
    22 VDDA Power
    27 VSS Power
    28 VDD Power
    49 VCAP_1 Power
    50 VDD Power
    73 VCAP_2 Power
    74 VSS Power
    75 VDD Power
    78 PC10 I/O USART3_TX
    79 PC11 I/O USART3_RX
    94 BOOT0 Boot
    99 VSS Power
    100 VDD Power

    Page 3
    USART Project
    Configuration Report

    4. Clock Tree Configuration

    Page 4
    USART Project
    Configuration Report

    5. IPs and Middleware Configuration

    5.1. SYS
    Timebase Source: SysTick

    5.2. USART3
    Mode: Asynchronous

    5.2.1. Parameter Settings:

    Basic Parameters:
    Baud Rate 115200
    Word Length 8 Bits (including Parity)
    Parity None
    Stop Bits 1

    Advanced Parameters:
    Data Direction Receive and Transmit
    Over Sampling 16 Samples

    * User modified value

    Page 5
    USART Project
    Configuration Report

    6. System Configuration

    6.1. GPIO configuration

    IP Pin Signal GPIO mode GPIO pull/up pull Max User Label
    down Speed
    USART3 PC10 USART3_TX Alternate Function Push Pull Pull-up Very High
    *
    PC11 USART3_RX Alternate Function Push Pull Pull-up Very High
    *

    6.2. DMA configuration

    nothing configured in DMA service

    Page 6
    USART Project
    Configuration Report

    6.3. NVIC configuration

    Interrupt Table Enable Preenmption Priority SubPriority


    Non maskable interrupt true 0 0
    Hard fault interrupt true 0 0
    Memory management fault true 0 0
    Pre-fetch fault, memory access fault true 0 0
    Undefined instruction or illegal state true 0 0
    System service call via SWI instruction true 0 0
    Debug monitor true 0 0
    Pendable request for system service true 0 0
    System tick timer true 0 0
    PVD interrupt through EXTI line 16 unused
    Flash global interrupt unused
    RCC global interrupt unused
    USART3 global interrupt unused
    FPU global interrupt unused

    * User modified value

    Page 7
    USART Project
    Configuration Report

    7. Power Consumption Calculator report

    7.1. Microcontroller Selection

    Series STM32F4
    Line STM32F407/417
    MCU STM32F407VETx
    Datasheet 022152_Rev7

    7.2. Parameter Selection

    Temperature 25
    Vdd 3.3

    Page 8
    USART Project
    Configuration Report

    8. Software Project

    8.1. Project Settings

    Name Value
    Project Name USART
    Project Folder D:\Open407V-D-Demo-HAL\5.UART\1.USART_Printf\USART
    Toolchain / IDE MDK-ARM V5
    Firmware Package Name and Version STM32Cube FW_F4 V1.14.0

    8.2. Code Generation Settings

    Name Value
    STM32Cube Firmware Library Package Copy all used libraries into the project folder
    Generate peripheral initialization as a pair of '.c/.h' files Yes
    Backup previously generated files when re-generating No
    Delete previously generated files when not re-generated Yes
    Set all free pins as analog (to optimize the power No
    consumption)

    Page 9

    You might also like