OCR (A) Physics A-level

Module 4 - Electrons, Waves and Photons

Definitions and Concepts

www.pmt.education
 Definitions and Concepts for OCR (A) Physics A-level

Module 4 - Electrons, Waves and Photons

4.1: Charge and Current

Conductors: ​A material that allows the flow of electrical charge. Good conductors
have a larger amount of free charge carriers to carry a current.

Conservation of Charge: ​The total charge in a system cannot change.

Conventional Current: ​The flow from positive to negative, used to describe the
direction of current in a circuit.

Coulomb: ​The unit of charge.

Electric Current: ​The rate of flow of charge in a circuit.

Electrolytes: ​Substances that contain ions that when dissolved in a solution, act
as charge carriers and allow current to flow.

Electron Flow: ​The opposite direction to conventional current flow. Electrons flow
from negative to positive.

Elementary Charge: ​The smallest possible charge, equal to the charge of an

electron.

Insulators: ​A material that has no free charge carriers and so doesn’t allow the
flow of electrical charge.

Kirchhoff's First Law: ​A consequence of the conservation of charge. The total

current entering a junction must equal the total current leaving it.

Mean Drift Velocity: ​The average velocity of an electron passing through an

object. It is proportional to the current, and inversely proportional to the number of
charge carriers and the cross-sectional area of the object.

Quantisation of Charge: ​The idea that charge can only exist in discrete packets
of multiples of the elementary charge.

Semiconductors: ​A material that has the ability to change its number of charge
carriers, and so its ability to conduct electricity. Light dependent resistors and
thermistors are both examples.

www.pmt.education
4.2: Energy, Power and Resistance

Diode: ​A component that allows current through in one direction only. In the
correct direction, diodes have a threshold voltage (typically 0.6 V) above which
current can flow.

Electromotive Force: ​The energy supplied by a source per unit charge passing
through the source, measured in volts.

Filament Lamp: ​A bulb consisting of a metal filament, that heats up and glows to
produce light. As the filament increases in temperature, its resistance increases
since the metal ions vibrate more and make it harder for the charge carriers to
pass through.

I-V Characteristics: ​Plots of current against voltage, that show how different
components behave.

Kilowatt-Hour: ​A unit of electrical energy. It is usually used to measure domestic

power consumption.

Light-Dependent Resistor: ​A light sensitive semiconductor whose resistance

increases when light intensity decreases.

Negative Temperature Coefficient Thermistor:

Ohm: ​The unit of resistance.

Ohmic Conductor: ​A conductor for which the current flow is directly proportional
to the potential difference across it, when under constant physical conditions.

Ohm’s Law: ​The current and potential difference through an ohmic conductor
held under constant physical conditions are directly proportional, with the constant
of proportionality being resistance.

Potential Difference: ​The difference in electrical potential between two points in a

circuit. It is also the work done per coulomb to move a charge from the lower
potential point to the higher potential point. It is measured in Volts.

Power: ​The rate of energy transfer in a circuit. It can be calculated as the product
of the current and the potential difference between two points. It is measured in
Watts.

Resistance: ​A measure of how difficult it is for current to flow through a material.

www.pmt.education
Resistivity: ​A measure of how difficult it is for charge to travel through a material.
It is proportional to the object’s resistance and cross-sectional area, and inversely
proportional to the object’s length. It is measured in Ohm metres.

Resistor: ​A device that has a fixed resistance and follows Ohm’s law.

Volt: ​The unit of potential difference.

4.3: Electrical Circuits

Conservation of Energy: ​Energy cannot be created or destroyed - it can only be

transferred into different forms.

Internal Resistance: ​The resistance to the flow of charge within a source. Internal
resistance results in energy being dissipated within the source.

Kirchhoff's Second Law: ​A consequence of the conservation of energy. The sum

of the voltages in any closed loop must equal zero.

Lost Volts: ​The difference between a source’s emf and the terminal voltage. It is
equal to the potential difference across the source’s internal resistance.

Parallel Circuit: ​Components are said to be connected in parallel when they are
connected across each other (separate loops).

Potential Divider: ​A method of splitting a potential difference, by connecting two

resistors in series. The total potential difference is split in the ratio of their
resistances.

Resistors in Parallel: ​The potential difference across resistors connected in

parallel is identical for each resistor. The current is split between the resistors. The
total resistance is equal to the inverse of the sum of the inverses of the
resistances of the resistors.

Resistors in Series: ​The current through resistors connected in series is identical

for each resistor. The potential difference is split in the ratio of their resistances.
The total resistance is equal to the sum of the resistances of the resistors.

Sensor Circuits: ​A circuit that reacts to external conditions. They commonly

involve a semiconductor connected in a potential divider arrangement.

Series Circuit: ​Components are said to be connected in series when they are
connected end to end (in one loop).

www.pmt.education
Terminal PD: ​The potential difference across the terminals of a power source. It is
equal to the source’s emf minus any voltage drop over the source’s internal
resistance.

4.4: Waves

Amplitude: ​A wave’s maximum displacement from its equilibrium position.

Antinodes: ​A position of maximum displacement in a stationary wave.

Coherence: ​Waves with the same frequency and constant phase difference.

Constructive Interference: ​The type of interference that occurs when two waves
meet in phase. The wave amplitudes are superposed.

Critical Angle: ​The angle of incidence that results in an angle of refraction of

exactly 90​o .​ It is when the refracted ray travels along the boundary line.

Destructive Interference: ​The type of interference that occurs when the two
waves are in antiphase. When one wave is at a peak and one is at a trough their
addition results in a minimum point.

Diffraction: ​The spreading of waves as they pass through a gap of a similar

magnitude to their wavelength.

Displacement: ​The distance that a point on a wave is from its equilibrium

position.

Electromagnetic Spectrum: ​The spectrum of electromagnetic waves, consisting

of Gamma Rays, X-Rays, Ultraviolet, Visible Light, Infrared, Microwaves and
Radiowaves.

Electromagnetic Waves: ​Waves that consist of perpendicular electric and

magnetic oscillations. All electromagnetic waves travel at the speed of light in a
vacuum.

Frequency: ​The number of waves that pass a point in a unit time period. It is the
inverse of the time period.

Fundamental Mode of Vibration: ​The oscillation of a wave at its natural

frequency.

Intensity: ​The power transferred per unit area. It is proportional to the square of a
wave’s amplitude.

www.pmt.education
Interference: ​The superposition of the amplitudes of waves when they meet.

Longitudinal Waves: ​A wave with oscillations that are parallel to the direction of
energy propagation. Sound waves are an example of a longitudinal wave. They
cannot travel through a vacuum.

Nodes: ​A position of minimum displacement in a stationary wave.

Oscilloscope: ​A device used to display and analyse waveforms.

Path Difference: ​A measure of how far ahead a wave is compared to another

wave, usually expressed in terms of the wavelength.

Period: ​The time taken for a wave to complete one full cycle.

Phase Difference: ​The difference in phase between two points on a wave. It is

usually expressed in radians.

Polarisation: ​The restriction of a wave so that it can only oscillate in a single

plane. This can only occur for transverse waves.

Progressive Waves: ​Waves that transfer energy from one point to another
without a transfer of matter.

Reflection: ​The bouncing of a wave at a boundary. The angle of incidence will

equal to the angle of reflection.

Refraction: ​The changing of speed of a wave as it passes into a new medium. If it

passes into an optically denser medium, it will slow down.

Refractive Index: ​A material property that is equal to the ratio between the speed
of light in a vacuum, and the speed of light in a given material.

Stationary Wave: ​A wave that stores, but does not transfer, energy.

Superposition: ​When two waves meet at the same point in space their
displacements combine and the total displacement at that point becomes the sum
of the individual displacements at that point.

Total Internal Reflection: ​An effect that occurs in optical fibres, where full
reflection occurs at the inside boundary of the fibre, meaning no radiation passes
out. The angle of incidence must be greater than the critical angle for this to occur.

Transverse Waves: ​A wave with oscillations that are perpendicular to the

direction of energy propagation. Electromagnetic waves are examples of
transverse waves.

www.pmt.education
Wave Speed: ​The product of a wave’s frequency and wavelength.

Wavelength: ​The distance between two identical positions on two adjacent

waves. It is commonly measured from peak to peak or trough to trough.

Young Double-Slit Experiment: ​An experiment that demonstrates the diffraction

of light by passing monochromatic light across two narrow slits and observing the
resulting pattern of bright and dark fringes.

www.pmt.education