Version 1.

1 , March 2001

Application Note
AN-TDA16888-0-010323

TDA 16888: Multioutput Single Transistor

Forward Converter 150W / 100kHz

Author: Michael Herfurth

Published by Infineon Technologies AG

http://www.infineon.com

Power Management & Supply

N e v e r s t o p t h i n k i n g
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

150W Output: 5V/18A; 12V/4A; -12V/1A; Standby: 5V/100mA

Operating Frequency: 100kHz

Contents:

1.Circuit description................................................................... 3
2. Circuit diagram....................................................................... 6
3. Test results............................................................................. 7
4. Bill of materials...................................................................... 8
5. Control PCB layout................................................................ 11
6. Power PCB layout.................................................................. 12
7. Transformer design............................................................... 13
8. Smoothing choke design...................................................... 14
9. Boost inductor design........................................................... 15
10. RFI choke design................................................................. 16
11. Picture of testboard............................................................. 17

2 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Circuit description
Multioutput single transistor forward converter with boost PFC preconverter

The power supply for a PC using up to 150 W of power must, for example, provide the following
voltages: 5V/18A; 12V/4A; -12V/0.7A; -5V/0,3A; and Standby 5V/0.1A. If any of the mains systems
in use around the world may be used as a power source, then an input voltage range of 90V to 270V
AC is required, taking into account the relevant tolerances.

The application circuit using the TDA 16888 is able to cover universal input voltage range mentioned
above (if required). In this circuit a boost converter (Q1, L2, D5, C3) works as an active harmonic filter
to provide power factor correction, intermediate circuit voltage stabilization and to supply the primary
and secondary side control logic in normal and standby operation. In addition, the bridging time for
dips in the mains voltage is not dependent on the mains voltage level. How the IC works in a typical
application circuit is described below.

Start up

When the mains voltage is switched on, the smoothing capacitor C3 is charged by a current pulse, the
current being limited by the winding resistances of the chokes and NTC resistor R36. Start-up
capacitor C11A is charged by a low current (<1mA) through resistors R2 and R43. Once the switch-on
threshold (14V) is reached at pin 19, the TDA 16888 changes from the passive to the active state. In
the passive state the IC draws a maximum current of 100µA while monitoring the switching thresholds
and actively maintaining the driver outputs at the L-level. In the active state the chip first checks
whether the intermediate circuit voltage at pin 19 lies between 20% and 120% of its nominal value
(e.g. between 80V and 480V for a nominal value of 400V). If this is the case, the chip concludes that
monitoring for the intermediate circuit voltage is connected (FMEA) and there is no risk to operation
from an overvoltage.

If the intermediate circuit voltage is found to be satisfactory, and no excess current is detected at pin
6, then the PFC converter starts working at half the rated frequency to cut the IC current consumption.
During this process the TDA 16888 is initially powered from the start-up capacitor C11A until the boost
converter starts to supply it, or, should the IC switch-off threshold (11V) be reached first, it switches
into the passive state and a new start-up attempt is initiated. As soon as the intermediate circuit
voltage has reached 80% of its nominal value, the PWM also starts running, with both converter
sections now operating at the rated frequency. A soft-start procedure is used for the PMW converter,
the rise time being set using C14 at pin 13.

If the voltage at pin 13 is less than 0.4V, the chip interprets this condition as standby mode, and shuts
off the PWM section. In standby mode the PFC converter again works at half the rated frequency to
reduce current consumption.

While the MOSFET Q1is switching, a modulated AC voltage appears at the secondary windings of
choke L2. The voltage across the main winding of choke L2 varies during rated operation from 400V
when Q1 is cut off and the AC input voltage passes through zero, to 400V when Q1 is conducting and
the maximum input voltage is at its peak value. The lowest voltage across the main winding (±200V)
arises when the input voltage is exactly half as large as the intermediate circuit voltage. This is why
the standby and IC supply voltages are derived from bridge rectification of the auxiliary windings on
L2, in order to use both the cut-off and conduction phase of the inductance. The voltage regulators IC5
and Q3/D11 are required because of the variation by a factor of 2 in the dc voltage obtained.

When the PFC converter is run up, the intermediate circuit voltage overshoots. Under low load it takes
a considerable time to return to its nominal level, because of the slow discharge of the smoothing
capacitor C3. During this period the voltage regulator would cut off the MOSFET Q1(up to more than
100ms), which would prevent the control logic being supplied from the boost converter choke. This is
why the TDA 16888 has a further control loop, using input pin 20, in addition to the two control loops
for the intermediate circuit voltage and the input current. A second output path from the boost
converter (D6, C4, R2) is taken via potential divider R1, R27 to detect whether Q1 is operating.

3 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz
This works by the voltage at C4 being set using voltage divider R1, R27 to the nominal value of the
intermediate circuit voltage, or a few percent below. The short time constant of the second output path
from the boost converter (C4≈10nF, R2≈500kΩ) means that any drop in the voltage at C4 is rapidly
detected, and the MOSFET Q1 switched on via the PFC current regulator. If necessary this is done
with such short pulses that the voltage at the main output from the boost converter does not rise, even
with no load at all. The limited controllability of the boost converter during no-load conditions means
that the power available at the standby output is limited. For example 5V/100mA is provided with a
quite good efficiency.

Normal operation

The oscillator frequency is set by just one external resistor R24. The ramp voltages for the oscillator
and the pulse width modulation (PWM) of the PFC section are generated across integrated capacitors.
The duty cycle of the PFC section varies from 0 to over 90%, and for the PWM section from 0 to 50%
maximum. During one switching period, the PFC MOSFET Q1 switches on first. The PWM MOSFET
Q2 switches on half a period later. For greater reliability, flip-flops are used to control this timing
sequence. The oscillator therefore runs at twice the rate of the external operating frequency. By
integrating the capacitors, external circuitry is not required, and so the current consumption is reduced
because of the smaller capacitances.

The waveform of the rectified, unsmoothed mains voltage is detected across resistors R4A, R4B, and
applied to the first input of an integrated multiplier. The output voltage from the PFC voltage control
amplifier is taken to at the second input to the multiplier. The current at the output of the multiplier, pin
4, is a reference value having the waveform of the rectified mains voltage and an amplitude controlled
by the voltage regulator. The PFC current regulator controls the rectified mains current such that the
voltage drop across shunt R6 assumes exactly the same value as the voltage drop across R5
produced by the output current from the multiplier. The output current from the PFC current regulator
(pin 3) sets up the duty cycle for the MOSFET Q1 by comparison with an internally generated ramp
voltage.

The intermediate circuit voltage is regulated by the PFC voltage regulator (pin 17, pin 18) at a level
that is greater than or equal to the peak value of the maximum input voltage (270V⋅√2= 382V). An
intermediate circuit voltage of 380V is often chosen, because one must expect a maximum voltage of
this magnitude even without a PFC converter. A 450V type smoothing capacitor (C3) is used,
however, to ensure that even under transient conditions, the voltage remains below the permitted
capacitor voltage. In this case it is worth increasing the intermediate circuit voltage to 410V, and to
design the onset threshold for overvoltage limiting to be 430V (R11, R12 to give 5.5V at pin 19). The
intermediate circuit voltage still remains below 450V during transient conditions, and the benefit lies in
the 40% higher hold time, which can be bridged if the mains drops out.

The PWM converter is designed to work as a single-ended forward converter. The turn-on time is
determined by the oscillator, as soon as the voltage at the soft start input pin 13 and the control input
pin 14 exceeds 0.4V. After the soft start phase, the voltage at control input pin 14 together with the
ramp voltage at pin 15 controls the turn-off time. An improved current ramp control technique (current
mode control) is used here, where the ramp voltage has an amplitude 5 times higher than those
traditionally used. The current in the Q2 source path is also measured across shunt resistor R15, and
detected at pin 11. At a voltage of 1V at pin 11, the integrated overcurrent comparator switches off
MOSFET Q2. The signal at pin 11 is also amplified by a factor of 5 by a linear amplifier, and taken via
an internal 10k resistor to pin 15. A base ramp voltage with an amplitude of 1.5V is produced across
capacitor C13 connected to this pin, even when there is no transistor current (slope compensation).
This voltage can rise to over 6V when the maximum current flows through Q2. This allows pulse width
modulation at higher signal levels, enabling stable operation right up to no-load conditions.

The transformer Tr1 in the forward converter works at the pre-regulated intermediate circuit voltage.
This means that a higher transformer ratio can be selected, reducing the current load for the
MOSFET. Furthermore, a larger duty cycle can be set during normal operation because there is a
smaller variation range for the input voltage. The magnetization energy can be fed back into the
smoothing capacitor using a demagnetization winding and demagnetization diode D7.

4 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz
In forward converters with universal input voltage range this is not possible without pre-regulation, or
causes significant losses in the required demagnetization network. In our application circuit,
overvoltage peaks across MOSFET Q2 and diode D7 are efficiently limited using diodes D22 and D27
and network C31, R40. On the secondary side there is one rectifying and one freewheeling diode (D8,
D9; D20, D21) for each output voltage. A damping network (e.g. R41, C29; R42, C30) is connected in
parallel with every diode, to attenuate commutation-induced overvoltage spikes and transients.
Another RC element (R47, C34) damps the voltage decay in intermittent dc flow, to avoid irregular
premagnetization of the smoothing choke. The output voltages are taken via separate windings on a
common smoothing choke L3 to convert the switched voltages into a flow of current. The smoothing
capacitors (e.g. C15, C28) reduce the ripple on the output voltage and serve as a storage device when
the load changes rapidly. For high output currents it is advisable to divide up the smoothing
capacitance with small inductances (L5, L6), to compensate for the equivalent series resistance (ESR)
of the capacitors.

The output voltage with the highest stability specification is controlled directly by regulating amplifier
IC2 and optocoupler IC3. The other output voltages are stabilized indirectly by the choice of winding
ratio for transformer Tr1 and choke L3 according to the ratio of the output voltages. An extra
comparator IC6 and optocoupler IC4 monitor the standby output voltage. When the standby switch is
closed, the PWM converter is only started once the PFC converter has produced at least 90% of the
nominal voltage at the standby output. Standby operation can be initiated by opening the switch.
Transistor Q4 with low-pass filter at its base, prevents noise spikes and leakage currents from the
optocoupler from discharging the soft-start capacitor during normal operation.

Protective features

When a short circuit occurs on the output side, the primary current is limited by measuring the drop
across shunt R15. In applications with several output voltages, this only works as a short-term
protective measure, because the output rectifier, for example, cannot withstand the overload. Extra
protection can be provided by monitoring the output voltages for a minimum value, with a delayed
switch into standby mode.

To deal with overshoots in the intermediate circuit voltage, a switch-off threshold can be set as
required (e.g. 5% above the nominal value) using potential divider R11, R12. If this is exceeded than
the PFC converter cuts off the power to the intermediate circuit.

When transient mains surges occur which charge the smoothing capacitor C3 to 10% above the PFC
switch-off threshold, the PWM MOSFEET Q2 is also cut-off to protect the power supply unit. If the
mains voltage rises still further, then varistor R30 can limit it. Using these protective devices, the
application circuit can withstand transient mains surges of 600V and more.

Figure 1:
A 150W PC power supply
design with power factor
correction using TDA 16888
fits inside a typical PC
power supply silver box.

5 of 20 AN-TDA16888-0-010323
V1.1
 5V
R31 D16...D19 0,1A

R36A IC5 C20 -5V/0,3A

IC6
Fuse L1 C25 D1...D4 L2 R62 C19 D24
-12V
L4 C1 VBUS = 410V L3 + 0,7A
90V- D23 C38 C38A
270V AC RFI C24 + R48
D5
R30 R40
Tr.1 D20
D6 12V
C26 C3A C31 R44 R46 4A
R36 AUX1 R43 + +
C33 R45 C36 C37
D22 C32 C35
D21
C4
SIPMOS C3 D8 L3 L6
C2 600V 5V
R1 = R4A Q1 R10 D27
= R2 R6 R42 R47 + + 18A
D7
C15 C28
R29 C29 R41 C30
R14 R16 R15 D9 C34
R7 R12
R3 R4B R5 R8 R9 R11 = = C6
L3 L5
C10 SIPMOS
D12...D15 C41 1000V

6 of 20
R13
C9A C8 C7 C5
IC3
Q3 6 1 4 5 3 8 7 19 17 18
D10 R39
Current- Over- - Q2
+ PWM
limitation - voltage + R22 R20
R28 Current EA = R17 C16 C17
+ OFF =
Voltage EA R32 STANDBY
C18 STANDBY EA
D11 Startup R21
UVLO VREF Soft-

-
+ OSC start PWM
C21 IC2
= R18 R19
9 12 2 20 16 15 13 14 10 11
IC4
IC1
Forward Converter 150W / 100kHz

R33 C27 R37

R26

R25 R35 IC6

R27 C23 R24 C13 C14 Q4 C22A
+ R23 C39 C42
C11 C12 C22
TDA 16888: Multioutput Single Transistor

C11A R38
= means R34 R35A
two resistors in series

AN-TDA16888-0-010323
V1.1
Circuit Diagram of single transistor multioutput forward converter with PFC
 V in I in P in PF THD V BUS V out1 I out1 V out2 I out2 V out3 I out3 V out4 I out4 VStby IStby P out Efficiency
V AC A rms W % % V DC V DC A V DC A V DC A V DC A V A W %
90 2,45 220,0 99,8 4,6 380,00 5,00 18,10 12,60 4,00 -12,70 0,70 -5,00 0,30 5,00 0,10 151,8 69,0
90 1,62 146,0 99,9 3,5 380,00 5,00 18,00 13,10 1,00 -13,40 0,10 -5,00 0,00 5,00 0,10 104,9 71,9
90 0,60 54,0 99,8 2,8 380,00 5,00 5,00 12,20 1,00 -12,30 0,10 -5,00 0,00 5,00 0,10 38,9 72,1
90 4,8 380,00 5,00 0,00 12,10 0,00 -11,90 0,00 -5,00 0,00 5,00 0,10 0,5
90 2,7 380,00 0,00 0,00 0,00 0,00 5,00 0,10 0,5

120 1,70 205,0 99,9 3,4 380,00 5,00 18,10 12,60 4,00 -12,70 0,70 -5,00 0,30 5,00 0,10 151,8 74,0
120 1,17 140,0 99,9 2,8 380,00 5,00 18,00 13,10 1,00 -13,40 0,10 -5,00 0,00 5,00 0,10 104,9 75,0
120 0,44 53,0 99,4 6,0 380,00 5,00 5,00 12,20 1,00 -12,30 0,10 -5,00 0,00 5,00 0,10 38,9 73,5
120 4,7 380,00 5,00 0,00 12,10 0,00 -11,90 0,00 -5,00 0,00 5,00 0,10 0,5
120 2,7 380,00 0,00 0,00 0,00 0,00 5,00 0,10 0,5

180 1,10 198,0 99,7 3,6 380,00 5,00 18,10 12,60 4,00 -12,70 0,70 -5,00 0,00 5,00 0,10 150,3 75,9
180 0,76 136,0 99,5 1,5 380,00 5,00 18,00 13,10 1,00 -13,40 0,10 -5,00 0,00 5,00 0,10 104,9 77,2

7 of 20
180 0,29 51,0 97,0 12,5 380,00 5,00 5,00 12,20 1,00 -12,30 0,10 -5,00 0,00 5,00 0,10 38,9 76,3
180 4,5 380,00 5,00 0,00 12,10 0,00 -11,90 0,00 -5,00 0,00 5,00 0,10 0,5
180 2,6 380,00 0,00 0,00 0,00 0,00 5,00 0,10 0,5

230 0,85 196,0 99,4 4,0 380,00 5,00 18,10 12,60 4,00 -12,70 0,70 -5,00 0,00 5,00 0,10 150,3 76,7
230 0,59 135,0 98,9 4,5 380,00 5,00 18,00 13,10 1,00 -13,40 0,10 -5,00 0,00 5,00 0,10 104,9 77,7
230 0,24 51,0 94,0 14,0 380,00 5,00 5,00 12,20 1,00 -12,30 0,10 -5,00 0,00 5,00 0,10 38,9 76,3
230 4,6 380,00 5,00 0,00 12,10 0,00 -11,90 0,00 -5,00 0,00 5,00 0,10 0,5
Forward Converter 150W / 100kHz

230 2,5 380,00 0,00 0,00 0,00 0,00 5,00 0,10 0,5

270 0,73 196,0 98,9 4,4 380,00 5,00 18,10 12,60 4,00 -12,70 0,70 -5,00 0,00 5,00 0,10 150,3 76,7
270 0,51 134,0 98,3 5,1 380,00 5,00 18,00 13,10 1,00 -13,40 0,10 -5,00 0,00 5,00 0,10 104,9 78,3
TDA 16888: Multioutput Single Transistor

270 0,21 51,0 90,4 16,0 380,00 5,00 5,00 12,20 1,00 -12,30 0,10 -5,00 0,00 5,00 0,10 38,9 76,3
270 4,4 380,00 5,00 0,00 12,10 0,00 -11,90 0,00 -5,00 0,00 5,00 0,10 0,5
270 2,5 380,00 0,00 0,00 0,00 0,00 0,5

AN-TDA16888-0-010323
V1.1
Test Results of single transistor multioutput forward converter with PFC
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Bill of Materials
Component Value Order-Nr. Manufacturer

IC 1 * TDA 16888 Q67000-A9284 Infineon

IC 2 TL 431 C TI
IC 3 CNY 17 F-3 Q62703-N50 Infineon
IC 4 CNY 17-3 Q62703-N88 Infineon
IC 5 TLE 4264 G Q67006-A-9139 Infineon
IC 6 TL 431 C TI

Q1 BUZ 91 (600V/ 0,8 Ω) Q67078-S1342-A2 Infineon

Q2 BUZ 51 (1000V/ 4Ω) Q67078-S1344-A2 Infineon
Q3 BSS 129 (240V/ 20Ω, Depletion) Q67000-S116 Infineon
Q4 * BC 338 (30V/ 800mA, NPN) Q62702-C314 Infineon

D 1...D 4 GR B250 C5000/3300

D5 STTA506D (600V; 5A; 20ns) ST
D6 MUR 160 (600V; 1A; 75ns) Motorola
D7 BYT 11-1000 (1000V; 1A; 100ns) ST
D 8, D 9 MBR 2535 CTL (Schottky 35V; 2x 12,5A) Motorola
D 10 1N4148
D 11 BZX 83 C13
D 12...D 15 UF 4003 (100V; 1A; 50ns) GI
D 16...D 19 UF 4003 (100V; 1A; 50ns) GI
D 20, D 21 BYV 32-100 (100V; 2x 10A; 25ns) Eupec, Philips
D 22 BYT 11-1000 (1000V; 1A; 100ns) ST
D 23, D 24 MUR 120 (200V; 1A; 50ns) Motorola
D 27 BYT 11-1000 (1000V; 1A; 100ns) ST
L1 2x 6,8mH/ 2A B82724-J2202-N1 EPCOS
L2 1mH E36/11; N27; GAP 2mm B66389-G1000-X127 EPCOS
100turns, 0,6mm ∅
AUX 1: 8turns 0,33mm ∅
AUX 2: 5turns 0,33mm ∅

L3 8µH (W3) E36/11, N27, GAP 2mm B66389-G1000-X127 EPCOS

W3: 9turns 2x 2x0,9mm ∅
W1: 21turns 0,7mm ∅
W2: 21turns 0,3mm ∅
L4 500µH EF25, N27, GAP 2mm B66317-G1000-X127 EPCOS
90turns, 0,45mm ∅
L5 1µH 9turns 2mm ∅ airchoke
L6 1µH 10turns 1,2mm ∅ airchoke
Fuse 2,5A MT

Component Value Order-Nr. Manufacturer

T1 E36/11, N27, without GAP B66389-G-X127 EPCOS

Primary: 68 turns 0,40mm ∅
Demagn.: 68 turns 0,22mm ∅
Sec.1: 3 turns 4x 0,8mm ∅
Sec.2: 7 turns 2x 0,8mm ∅
Sec.3: 7 turns 0,4mm ∅

8 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Component Value Order-Nr. Manufacturer

C1 0,33µF 275V AC, X2 B81133-D1334-M EPCOS

C2 not assembled
C3 150µF/ 450V Elko B43501-J5157-M EPCOS
C 3A 0,15µF/ 630V MKP B32652-A6154-K EPCOS
C4 10nF/ 1000V MKP B32652-A103-K EPCOS
C5 * 47nF/63V MKT B32529-C473-K EPCOS
C6 * 100nF/63V MKT B32529-C104-K EPCOS
C7 * 1nF/63V MKT B32529-C102-K EPCOS
C8 * 10nF/63V MKT B32529-C103-K EPCOS
C9 * not assembled
C 9A * 6,8nF/63V MKT B32529-C682-K EPCOS
C 10 * 10pF/100V CG B37979-G1100-J51 EPCOS
C 11 * 0,47µF/63V MKT B32529-C474-K EPCOS
C 11A * 100µF/25V Elko B41283-C5107-T90 EPCOS
C 11B * 47nF/50V X7R B37981-F5473-K51 EPCOS
C 12 * 0,15µF/63V MKT B32529-C154-K EPCOS
C 13 * 100pF/50V CG B37979-G5101-J51 EPCOS
C 14 * 100nF/63V MKT B32529-C104-K EPCOS
C 15 2200µF/10V Elko B41822-A3228-M EPCOS
C 16 68nF/63V MKT B32529-C683-K EPCOS
C 17 2,2nF/63V MKT B32529-C222-K EPCOS
C 18 100µF/63V Elko B41822-A8107-M EPCOS
C 19 470µF/35V Elko B41822-A7477-M EPCOS
C 20 100µF/25V Elko B41822-A1107-M EPCOS
C 21 * 220pF/50V CG B37979-G5221-J51 EPCOS
C 22 * 4,7nF/63V MKT B32529-C472-K EPCOS
C 22A * 10nF MKT B32529-C103-K EPCOS
C 23 * not assembled
C 24 0,33µF 275V AC, X2 B81133-D1334-M EPCOS
C 25, C 26 3,3nF 250V AC, Y2, lead spacing 15mm B81121-C-B142 EPCOS
C 25, C 26 3,3nF 250V AC, Y2, lead spacing 10mm B81122-C1332-M EPCOS
C 27 4,7nF/63V MKT B32529-C472-K EPCOS
C 28 2200µF/10V Elko B41822-A3228-M EPCOS
C 29 1nF/63V MKT B32529-C102-K EPCOS
C 30 1nF/63V MKT B32529-C102-K EPCOS
C 31 1nF/630V Position R 40
C 32 2,2nF/63V MKT B32529-C222-K EPCOS
C 33 2,2nF/63V MKT B32529-C222-K EPCOS

C 34 insert wire bridge

C 35 insert wire bridge
C 36 1000µF/16V B41822-A4108-M EPCOS
C 37 1000µF/16V B41822-A4108-M EPCOS
C 38 470µF/16V B41822-A4477-M EPCOS
C 39 3,3nF 250V AC, Y1 B81123-C1332-M EPCOS
C 41 * 220pF/50V CG B37979-G5221-J51 EPCOS
C 40 not assembled
C 42 insert wire bridge
C 1,5nF/630V assembled between Heatsink of
Q2 and BUS Voltage
* = located on control board

9 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz
Component Value Order-Nr. Manufacturer
R1 * 3825K 2x 1,91M metal
R2 220K
R 2A 220K
R3 * 22K
R 4A * 390K metal
R 4B * 390K metal
R5 * 2,2K
R6 0,22 1 + 2x 0,56 parallel
R7 * 2,2K
R8 * 7,5K
R9 3,3
R 10 18K
R 11 * 51K metal
R 12 * 3825K 2x 1,91M metal
R 13 * 3825K 2x 1,91M metal
R 14 * 51K metal
R 15 0,50 2x 1 parallel
R 16 * 390K
R 17 18K
R 18 3,3
R 19 5,1K metal
R 20 5,1K metal
R 21 10K
R 22 680
R 23 * 33K
R 24 * 51 K metal
R 25 * 10K
R 26 * 68K
R 27 * 51K metal
R 28 4,7K
R 29 1
R 30 SIOV-S14K250G5 Q69x4603 EPCOS
R 31 insert wire bridge
R 32 * 1,1K
R 33 470
R 34 * 56K
R 35 * 1,1K
R 35A * 680
R 36A 56 4W
R 37 3,9K metal
R 38 5,1K metal
R 39 1K1
R 40 220K 2W
R 41 33
R 42 33
R 43 not assembled
R 43 A 330K 2W between VBUS and VCC
R 44 56
R 45 56
R 46 470
R 47 100
R 48 470
R 49 not assembled
• = located on control board
Warning: Heatsink of D5 is connected to 380V BUS Voltage !

10 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Printed Circuit Board of control circuit

11 of 20 AN-TDA16888-0-010323
V1.1
TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Printed Circuit Board of power circuit

12 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Single ended feed forward Transformer

150W / 100kHz; Output voltage: 5V/18A; 12V/4A; -12V/1A
Core E36/18/11; N27; without gap; ALMIN = 2330nH; coil former vertical

Pin 5
34 turns 0,22 mm Ø MAG Pin 1
Pin 7
34 turns 0,40 mm Ø PRIM Pin 2
Pin 13
7 turns 0,4mm Ø SEC Pin 16
Pin 14
7 turns 2 x 0,8mm Ø SEC Pin 15
Pin 9+10
3 turns 4 x 0,8mm Ø SEC Pin 11+12
Pin 2
34 turns 0,40 mm Ø PRIM Pin 5
Pin 1
34 turns 0,22 mm Ø MAG Pin 4

center

means one layer Makrofol

Primary winding 68 turns 0,40 mm ∅ transformer wire

Demagnetization 68 turns 0,22 mm ∅ transformer wire
Secondary winding1 3 turns 4 x 0,8 mm ∅ transformer wire
Secondary winding2 7 turns 2 x 0,8 mm ∅ transformer wire
Secondary winding3 7 turns 0,4 mm ∅ transformer wire
Top
5
11, 12
Pin 1 • • Pin 16
4 M P
1 A RI 15 Pin 2 • • Pin 15
G 16
2 S S S • • Pin 14
2 E E E
C C Pin 4 • • Pin 13
C 13
1 M P Pin 5 • • Pin 12
5 A RI 14
G • • Pin 11
7 9, 10 Pin 7 • • Pin 10
Pin 8 • • Pin 9

13 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Smoothing Choke of single ended forward converter

Core E36/18/11; N27; total gap = 2mm; AL = 100nH; coil former horizontal;
L = 8µH; @5V output

Pin 6 21 turns 0,3mm Ø w3 Pin 13

Pin 7 21 turns 0,7mm Ø w2 Pin 10

Pin 3 9 turns 2x 0,95mm Ø w1 Pin 14

Pin 2 9 turns 2x 0,95mm Ø w1 Pin 15

center

Winding 1: 9 turns 2 x 2 x 0,95 mm ∅ transformer wire

Winding 2: 21 turns 0,7 mm ∅ transformer wire
Winding 2: 21 turns 0,3 mm ∅ transformer wire

Top

Pin 8• • Pin 9
Pin 7• • Pin 10
Pin 6• • Pin 11
Pin 5• • Pin 12
Pin 4• • Pin 13
Pin 3• • Pin 14
Pin 2• • Pin 15
Pin 1• • Pin 16

14 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

Boost converter choke for PFC

Core E36/18/11; N27; total gap = 2mm; AL = 100 nH;

L = 1 mH; IPEAK = 3,5 A; coil former vertical

Pin 11
W1: 25 turns 30x 0,1 mm Ø

W1: 25 turns 30x 0,1 mm Ø Pin 14

Pin 1
W3: 5 turns 0,30 mm Ø Pin 2
Pin 7
W2: 8 turns 0,30 mm Ø Pin 5
Pin 14
W1: 25 turns 30x 0,1 mm Ø

W1: 25 turns 30x 0,1 mm Ø Pin 13

center

1 layer Top

Pin 1 • • Pin 16
Pin 2 • • Pin 15
W1 : 100 turns 30 x 0,1stranded wire w/ silk
• • Pin 14
W2 : 8 turns 0,30 transformer wire
W3 : 5 turns 0,30 transformer wire Pin 4 • • Pin 13
Pin 5 • • Pin 12
• • Pin 11
Pin 7 • • Pin 10
Pin 8 • • Pin 9

15 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

RFI Choke L= 470µH, IPEAK= 3,5A

Core E 25/13/7 (EF25), N27, total gap= 2mm, AL=54 nH,

coil former vertical

22,5 turns 0,55 mm Ø Pin 4

22 turns 0,55 mm Ø

22 turns 0,55 mm Ø

22 turns 0,55 mm Ø Pin 9

means one layer of Makrofol

88,5 turns transformer wire 0,55 mm Ø

Top
Pin 1 • • Pin 10
• •
• •
• •
Pin 5 • • Pin 6

16 of 20 AN-TDA16888-0-010323
V1.1
TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

17 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

References:

[1] nnn

Revision History
Application Note AN-TDA16888-0-010323
Actual Release: V1.1 Date:2001-03-23 Previous Release: V0.1
Page of Page of Subjects changed since last release
actual prev.
Release Release

18 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz

For questions on technology, delivery and prices please contact the Infineon
Technologies Offices in Germany or the Infineon Technologies Companies and
Representatives worldwide: see the address list on the last page or our webpage at

http://www.infineon.com

CoolMOS and CoolSET are trademarks of Infineon Technologies AG.

Edition 2000-03--03
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München
© Infineon Technologies AG 2000.
All Rights Reserved.

Attention please!
The information herein is given to describe certain components and shall not be considered as warranted characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts
stated herein.
Infineon Technologies is an approved CECC manufacturer.

Information
For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in
Germany or our Infineon Technologies Representatives worldwide (see address list).

Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your
nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon
Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the
safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support
and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be
endangered.

19 of 20 AN-TDA16888-0-010323
V1.1
 TDA 16888: Multioutput Single Transistor
Forward Converter 150W / 100kHz
Infineon Technologies AG sales offices worldwide –
partly represented by Siemens AG
A F J RC
Siemens AG Österreich Infineon Technologies France, Siemens Components K.K. Infineon Technologies
Erdberger Lände 26 39/47,Bd.Ornano Talanawa Park Tower 12F &17F Asia Pacific Pte.Ltd.
A-1031 Wien F-93527 Saint-Denis CEDEX2 3-20-14,Higashi-Gotanda, Taiwan Branch
T (+43)1-17 07-3 56 11 T (+33)1-49 22 31 00 Shinagawa-ku 10F,No.136 Nan King East Road
Fax (+43)1-17 07-5 59 73 Fax (+33)1-49 22 28 01 Tokyo Section 23,Taipei
AUS FIN T (+81)3-54 49 64 11 T (+8 86)2-27 73 66 06
Siemens Ltd. Siemens Components Fax (+81)3 -54 49 64 01 Fax (+8 86)2-27 71 20 76
885 Mountain Highway Scandinavia MAL SGP
Bayswater,Victoria 3153 P.O .Bo x 6 0 Infineon Technologies AG Infineon Technologies Asia
T (+61)3-97 21 21 11 FIN-02601 Espoo (Helsinki) Sdn Bhd Pacific,Pte.Ltd.
Fax (+61)3-97 21 72 75 T (+3 58)10-5 11 51 51 Bayan Lepas Free Industrial Zone1 168 Kallang Way
B Fax (+3 58)10-5 11 24 95 11900 Penang Singapore 349 253
Siemens Electronic Components Email: T (+60)4 -6 44 99 75 T (+65)8 40 06 10
Benelux [email protected] Fax (+60)4 -6 41 48 72 Fax (+65)7 42 62 39
Charleroisesteenweg 116/ GB N USA
Chaussée de Charleroi 116 Infineon Technologies Siemens Components Infineon Technologies Corporation
B-1060 Brussel/Bruxelles Siemens House Scandinavia 1730 North First Street
T (+32)2-5 36 69 05 Oldbury Østre Aker vei 24 San Jose,CA 95112
Fax (+32)2-5 36 28 57 GB-Bracknell,Berkshire Postboks 10,Veitvet T (+1)4 08-5 01 60 00
Email:[email protected] RG12 8FZ N-0518 Oslo Fax (+1)4 08-5 01 24 24
BR T (+44)13 44-39 66 18 T (+47)22-63 30 00 Siemens Components,Inc.
Siemens Ltda. Fax (+44)13 44-39 66 32 Fax (+47)22-68 49 13 Optoelectronics Division
Semiconductores H Email: 19000 Homestead Road
Avenida Mutinga,3800-Pirituba Simacomp Kft. [email protected] Cupertino,CA 95014
05110-901 São Paulo-SP Lajos u.103 NL T (+1)4 08-2 57 79 10
T (+55)11-39 08 25 64 H-1036 Budapest Siemens Electronic Components Fax (+1)4 08-7 25 34 39
Fax (+55)11-39 08 27 28 T (+36)1-4 57 16 90 Benelux Siemens Components,Inc.
CDN Fax (+36)1-4 57 16 92 Postbus 16068 Special Products Division
Infineon Technologies Corporation HK NL-2500 BB Den Haag 186 Wood Avenue South
320 March Road,Suite 604 Infineon Technologies T (+31)70-3 33 20 65 Iselin,NJ 08830-2770
Canada,Ontario K2K 2E2 Hong Kong Ltd. Fax (+31)70-3 33 28 15 T (+1)7 32-9 06 43 00
T (+1)6 13-5 91 63 86 Suite 302,Level 3, Email:[email protected] Fax (+1)7 32-6 32 28 30
Fax (+1)6 13-5 91 63 89 Festival Walk, NZ VRC
CH 80 Tat Chee Avenue, Siemens Auckland Infineon Technologies
Siemens Schweiz AG Yam Yat Tsuen, 300 Great South Road Hong Kong Ltd.
Bauelemente Kowloon Tong Greenland Beijing Office
Freilagerstrasse 40 Hong Kong Auckland Room 2106,Building A
CH-8047 Zürich T (+8 52)28 32 05 00 T (+64)9-5 20 30 33 Vantone New World Plaza
T (+41)1-4 953065 Fax (+8 52)28 27 97 62 Fax (+64)9-5 20 15 56 No.2 Fu Cheng Men Wai Da Jie
Fax (+41)1-4 955050 I P
D
Jie
Siemens S..A. Siemens S.A. 100037 Beijing
Infineon Technologies AG Semiconductor Sales an Componentes Electronicos
Völklinger Str.2 T (+86)10 -68 57 90 -06,-07
Via Piero e Alberto Pirelli,10 R.Irmaos Siemens,1
D-40219 Düsseldorf Fax (+86)10 -68 57 90 08
I-20126 Milano Alfragide
T (+49)2 11-3 99 29 30 Infineon Technologies
T (+39)02-66 76 -1 P-2720-093 Amadora
Fax (+49)2 11-3 99 14 81 Hong Kong Ltd.
Fax (+39)02-66 76 43 95 T (+351)1-4 17 85 90
Infineon Technologies AG IND
Chengdu Office
Fax (+351)1-4 17 80 83
Werner-von-Siemens-Platz 1 Siemens Ltd. PK
Room14J1,Jinyang Mansion
D-30880 Laatzen (Hannover) Components Division Siemens Pakistan Engineering 58 Tidu Street
T (+49)5 11-8 77 22 22 No.84 Keonics Electronic City Co.Ltd. Chengdu,
Fax (+49)5 11-8 77 15 20 Hosur Road PO Box 1129,Islamabad 44000 Sichuan Province 610 016
Infineon Technologies AG Bangalore 561 229 23 West Jinnah Ave T (+86)28-6 61 54 46 /79 51
Von-der-Tann-Straße 30 T (+91)80-8 52 11 22 Islamabad Fax (+86)28 -6 61 01 59
D-90439 Nürnberg Fax (+91)80-8 52 11 80 T (+92)51-21 22 00 Infineon Technologies
T (+49)9 11-6 54 76 99 Siemens Ltd. Fax (+92)51-21 16 10 Hong Kong Ltd.
Fax (+49)9 11-6 54 76 24 CMP Div,5th Floor PL Shanghai Office
Infineon Technologies AG 4A Ring Road,IP Estate Siemens SP.z.o.o. Room1101,Lucky Target Square
Weissacher Straße 11 New Delhi 110 002 ul.Zupnicza 11 No.500 Chengdu Road North
D-70499 Stuttgart T (+91)11-3 31 99 12 PL-03-821 Warszawa Shanghai 200003
T (+49)7 11-1 37 33 14 Fax (+91)11-3 31 96 04 T (+48)22-8 70 91 50 T (+86)21-63 6126 18 /19
Fax (+49)7 11-1 37 24 48 Siemens Ltd. Fax (+48)22-8 70 91 59 Fax (+86)21-63 61 11 67
D CMP Div,4th Floor ROK Infineon Technologies
Infineon Technologies AG Siemens Ltd. Hong Kong Ltd.
130,Pandurang Budhkar Marg,
Halbleiter Distribution Asia Tower,10th Floor Shenzhen Office
Worli
Richard-Strauss-Straße 76 726 Yeoksam-dong,Kang-nam Ku Room 1502,Block A
Mumbai 400 018
D-81679 München CPO Box 3001 Tian An International Building
T (+91)22-4 96 21 99
T (+49)89-92 21 40 86 Seoul 135-080 Renim South Road
Fax (+91)22-4 96 22 01
Fax (+49)89-92 21 20 71 IRL T (+82)2-5 27 77 00 Shenzhen 518 005
DK Siemens Ltd. Fax (+82)2-5 27 77 79 T (+86)7 55 -2 28 91 04
Siemens A/S RUS
Electronic Components Division Fax (+86)7 55-2 28 02 17
Borupvang 3 INTECH electronics ZA
8,Raglan Road
DK-2750 Ballerup ul.Smolnaya,24/1203 Siemens Ltd.
IRL-Dublin 4
T (+45)44 77-44 77 RUS-125 445 Moskva Components Division
T (+3 53)1-2 16 23 42
Fax (+45)44 77-40 17 T (+7)0 95 -4 51 97 37 P.O.B.3438
Fax (+3 53)1-2 16 23 49
E IL Fax (+7)0 95 -4 51 86 08 Halfway House 1685
Siemens S.A. S T (+27)11-6 52 -27 02
Nisko Ltd.
Dpto.Componentes Siemens Components Scandinavia Fax (+27)11-6 52 20 42
2A,Habarzel St.
Ronda de Europa,5 Österögatan 1,Box 46
P.O.Box 58151
E-28760 Tres Cantos-Madrid S-164 93 Kista
61580 Tel Aviv –Isreal
T (+34)91-5 14 71 51 T (+46)8-7 03 35 00
T (+9 72)3 -7 65 73 00
Fax (+34)91-5 14 70 13 Fax (+46)8-7 03 35 01
Fax (+9 72)3 -7 65 73 33
Email:
[email protected]

20 of 20 AN-TDA16888-0-010323
V1.1