Oil Pump: A: Removal

SERVICE PROCEDURE [W1A0] 2-4
1. Oil Pump
1. Oil Pump 7) Remove water pipe and hoses between oil

cooler and water pump. (AT vehicles only)
A: REMOVAL
1) Set the vehicle on the lift.
2) Disconnect battery ground cable.
S2M0112
8) Lower the vehicle.

9) Remove radiator. <Ref. to 2-5 [W3A0].>
G6M0095
3) Lift-up the vehicle.

4) Remove under cover.
5) Drain coolant. <Ref. to 2-5 [W1A0].>
S2M0033
10) Remove crankshaft position sensor.
B2M0015
6) Remove bolts which install water pipe of oil

cooler to oil pump. (AT vehicles only)
B2M1252
11) Remove camshaft position sensor. <Ref. to

2-7 [W10A0].>
S2M0027
B2M2317
5
2-4 [W1A0] SERVICE PROCEDURE
1. Oil Pump
12) Remove V-belts. <Ref. to 1-5 [G2A0].> 16) Remove timing belt guide. (MT vehicles only)
G2M0286 S2M0115
13) Remove rear side V-belt tensioner. 17) Remove crankshaft sprocket.
S2M0113 S2M0116
14) Remove crankshaft pulley using ST. 18) Remove bolts which install oil pump onto cyl-
ST 499977100 CRANKSHAFT PULLEY inder block.
WRENCH
S2M0117
S2M0114
19) Remove oil pump using flat bladed screw-
15) Remove water pump. <Ref. to 2-5 [W1A0].> driver.
CAUTION:
Be careful not to scratch mating surfaces of
cylinder block and oil pump.
S2M0022
S2M1819
6
SERVICE PROCEDURE [W1C2] 2-4
1. Oil Pump
B: DISASSEMBLY C: INSPECTION
Remove screws which secure oil pump cover and 1. TIP CLEARANCE
disassemble oil pump.
Measure the tip clearance of rotors. If the clear-
Inscribe alignment marks on inner and outer rotors
ance exceeds the limit, replace rotors as a
so that they can be replaced in their original posi-
matched set.
tions during reassembly.
Tip clearance:
CAUTION:
Standard
Before removing relief valve, loosen plug when
0.04 — 0.14 mm (0.0016 — 0.0055 in)
removing oil pump from cylinder block.
Limit
0.18 mm (0.0071 in)
S2M0736
2. CASE CLEARANCE
Measure the clearance between the outer rotor
and the cylinder block rotor housing. If the clear-
ance exceeds the limit, replace the rotor.
Case clearance:
Standard
S2M0121A
0.10 — 0.175 mm (0.0039 — 0.0069 in)
Limit
(A) Oil seal 0.20 mm (0.0079 in)
(B) Pump case
(C) Inner rotor
(D) Outer rotor
(E) Pump cover
(F) Relief valve
(G) Relief spring
(H) Plug
(I) Washer
S2M0737
7
2-4 [W1C3] SERVICE PROCEDURE
1. Oil Pump
3. SIDE CLEARANCE D: ASSEMBLY

Measure clearance between oil pump inner rotor 1) Install front oil seal using ST.
and pump cover. If the clearance exceeds the limit, ST 499587100 OIL SEAL INSTALLER
replace rotor or pump body.
CAUTION:
Side clearance: Use a new oil seal.
Standard
0.02 — 0.07 mm (0.0008 — 0.0028 in)
Limit
0.15 mm (0.0059 in)
S2M0235A
2) Install inner and outer rotors in their original

positions.
G2M0075 3) Install oil relief valve and relief spring.
4) Install oil pump cover.
4. OIL RELIEF VALVE Tightening torque:
T1: 5 — 6 N·m (0.5 — 0.6 kg-m, 3.6 — 4.3
Check the valve for fitting condition and damage,
ft-lb)
and the relief valve spring for damage and deterio-
T2: 40.7 — 47.5 N·m (4.15 — 4.84 kg-m,
ration. Replace the parts if defective.
30.0 — 35.0 ft-lb)
Relief valve spring:
Free length; 71.8 mm (2.827 in)
Installed length; 54.7 mm (2.154 in)
Load when installed; 77.08 N (7.86 kg,
17.33 lb)
5. OIL PUMP CASE
Check the oil pump case for worn shaft hole,
clogged oil passage, worn rotor chamber, cracks,
and other faults.
6. OIL SEAL
Check the oil seal lips for deformation, hardening,
wear, etc. and replace if defective.
S2M0121B
8
SERVICE PROCEDURE [W2A0] 2-4
2. Oil Pan and Oil Strainer
E: INSTALLATION 2. Oil Pan and Oil Strainer

Install in the reverse order of removal. A: REMOVAL
Observe the following:
1) Apply fluid packing to matching surfaces of oil 1) Set the vehicle on the lift.
pump. 2) Disconnect battery ground cable.
Fluid packing:
THREE BOND 1215 or equivalent
2) Replace O-ring (A) with a new one.
G6M0095
3) Remove air intake duct and air cleaner assem-

bly. <Ref. to 2-7 [W1A0].>
S2M0739B
3) Apply a coat of engine oil to the inside of the oil

seal.
H2M2929
4) Disconnect front oxygen (A/F) sensor connec-

tor.
S2M0118B
4) Be careful not to scratch oil seal when installing

oil pump on cylinder block.
5) Position the oil pump, aligning the notched area
with the crankshaft, and push the oil pump straight.
CAUTION:
Make sure the oil seal lip is not folded.
6) Install oil pump.
Tightening torque:
B2M3439
T: 6.4 N·m (0.65 kg-m, 4.7 ft-lb)
S2M0740B

Oil Pump: A: Removal

Uploaded by

Copyright:

Available Formats

Oil Pump: A: Removal

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Oil Pump: A: Removal

Uploaded by

Copyright:

Available Formats

SERVICE PROCEDURE [W1A0] 2-4

1. Oil Pump 7) Remove water pipe and hoses between oil

8) Lower the vehicle.

3) Lift-up the vehicle.

10) Remove crankshaft position sensor.

6) Remove bolts which install water pipe of oil

11) Remove camshaft position sensor. <Ref. to

3. SIDE CLEARANCE D: ASSEMBLY

2) Install inner and outer rotors in their original

E: INSTALLATION 2. Oil Pan and Oil Strainer

3) Remove air intake duct and air cleaner assem-

3) Apply a coat of engine oil to the inside of the oil

4) Disconnect front oxygen (A/F) sensor connec-

4) Be careful not to scratch oil seal when installing

You might also like