Scribd
Upload
584 views6 pages

What Is Inrush Current and How To Limit It

Inrush current is a brief, high surge of current that occurs when an electrical device is turned on. It is caused by components like transformers and motors that contain coils or inductors. Inrush current can be many times higher than the device's normal operating current and can damage components or trip circuit breakers. Various techniques can be used to limit inrush current, such as thermistors, soft starters, and voltage regulators. Proper measurement of inrush current requires using a clamp meter designed to measure brief current surges.

Uploaded by

Joseph B Delos Reyes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
584 views6 pages

What Is Inrush Current and How To Limit It

Inrush current is a brief, high surge of current that occurs when an electrical device is turned on. It is caused by components like transformers and motors that contain coils or inductors. Inrush current can be many times higher than the device's normal operating current and can damage components or trip circuit breakers. Various techniques can be used to limit inrush current, such as thermistors, soft starters, and voltage regulators. Proper measurement of inrush current requires using a clamp meter designed to measure brief current surges.

Uploaded by

Joseph B Delos Reyes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

What is Inrush Current and How to Limit

it?
power

ByPankaj Khatri Jan 23, 2019 0

What is Inrush Current and how to limit it

Inrush current is the maximum current drawn by an electrical circuit at the time it’s
turned ON. It appears for the few cycles of input waveform. The value of the inrush
current is much higher than the steady-state current of the circuit and this high current
can damage the device or trigger the circuit breaker. Inrush Current generally appears
in all the devices where magnetic core is present like transformers, industrial motors
etc. Inrush current is also known as Input surge current or Switch-On surge current.

Why Inrush Current Appears?

There are number of factors behind the cause of the inrush current. Like some devices
or systems which consists decoupling capacitor or smooth capacitor, draws a large
amount of current at start to charge them. Below given diagram will give you an idea
about the difference between an inrush, peak and steady state current of a circuit:
Peak Current: It’s the maximum value of current attained by a waveform either in
positive or negative region.

Steady-State Current: It is defined as the current at each time interval remain constant
in a circuit. A steady state current is achieved when di/dt = 0, which means the current
remain unchanged with respect to time. 

Inrush Current Characteristics:

 Occur instantaneously when device is turned on


 Appears for a short time of span
 Higher than the rated value of the circuit or device

Some examples where Inrush Current occurs:

 Incandescent Lamp
 Induction Motor Starting
 Transformer
 Turning ON SMPS based power supplies

Inrush Current in Transformer

Transformer inrush current is defined as the maximum instantaneous current drawn


by the transformer when the secondary side is unloaded or in open circuit condition.
This inrush current harms the magnetic property of the core and cause an unwanted
switching of transformer’s circuit breaker.

The magnitude of the inrush current is depending upon the point of AC wave at which
the transformer is starting. If transformer (at no load) turns on when the AC voltage is at
its peak then no inrush current will occur at the starting, and if transformer (at no load)
turns on when the AC voltage is passing through zero then the value of inrush current
will be very high and it also exceeds the saturation current, as you can see in the below
image:
Inrush Current in Motors

Like transformer induction motor do not have continuous magnetic path. Reluctance of
the induction motor is high due to the air gap between the rotor and the stator.
Therefore, due to this high reluctance induction motor requires high magnetizing current
to produce the rotating magnetic field at starting. The diagram below shows the full
voltage starting characteristics of the motor.
As you can see in the diagram, starting current and starting torque both are very high at
the beginning. This high starting current which is also called as inrush current, can
damage the electrical system and the initial high torque can affect the mechanical
system of the motor. If we reduce the initial voltage value by 50%, then it can result in
75% reduction of the motor torque. So, to overcome these problems soft start power
supply circuits (mainly called as soft starters) are used.

Should we care about Inrush Current and How to limit it?

Yes, we should always care about the inrush current in induction motors, transformers
and in the electronic circuits which consists inductors, capacitors or core. As previously
mentioned, inrush current is the maximum peak current, experienced in the system and
it can be twice or ten times of the normal rated current. This unwanted current spike can
damage the device like in transformer, inrush current can cause tripping of the circuit
breaker, every time it turns ON. Adjust the breaker tolerance may help us, but the
components should withstand the peak value at in-rush.

While in electronic circuit some components have specification to withstand with the
high value of inrush current for a short time span. But some components gets very hot
or get damaged if the value of in-rush is very high. So it’s better to use a inrush current
protection circuit while designing an electronic circuit or PCB.
For the protection from inrush current you can use an active or passive device.
Choosing the type of protection depends upon the frequency of the inrush current,
performance, cost, and reliability.

Like you can use a NTC thermistor (Negative Temperature Coefficient) which is a
passive device works as an electrical resistor whose resistance is very high at low-
temperature value. The NTC thermistor connects in the series with the power supply
input line. It exhibits high value of resistance at ambient temperature. So, when we turn
on the device the high resistance limits the inrush current to flow into the system. As the
current flow continuously the temperature of the thermistor rises which reduces the
resistance significantly. Hence, the thermistor stabilizes the inrush current and allows
the steady current to flow into the circuit. The NTC thermistor is widely used for the
current limiting purpose due to its simple design and low cost. It also have some
drawbacks like you cannot rely on thermistor in the extreme weather conditions.

Active devices are costlier and also increase the size of the system or circuit. It
consists of sensitive components that switch high incoming current. Some of the active
devices are Soft Starters, voltage regulators, and DC/DC converters.

These protections are used to protect the electrical as well as a mechanical system by
limiting the instantaneous inrush current. The below-mentioned graph show the inrush
current value with the protection circuit and without the protection circuit. We can clearly
see how effective an inrush current protection is.

How to measure Inrush Current?


You all have seen the bicycle cart, to get it moving the rider needs to apply a vigorous
force. And, once the wheel starts moving the required force get reduced. So, this initial
force is equivalent to the inrush current. Similarly, in motors, once the rotor starts
moving the motor starts reaching the steady state where it does not require high current
to run.

There are number of clamp meters (multimeter) available which offers inrush current
measurement. Like you can use Fluke 376 FC True-RMS Clamp meter to measure the
inrush current. Sometimes the inrush current shows a value which is higher than the
rating of the circuit breaker, but still, the breaker does not trip. The reason behind this is,
the circuit breaker works on a time v/s current curve, like you are using a 10 amps
circuit breaker, so the inrush current which is more than 10 amps should flow through
the circuit breaker more than the rated time of it.

Follow the below mentioned steps to measure the inrush current:

 Tested device should be turned off initially


 Rotate the dial and set to the Hz-Ã sign
 Place the live wire into the jaw or use probe connected with the clamp meter
 Press the inrush current button in the clamp meter, as shown in the above image
 Turn the device ON, you will get the inrush current value on the meter’s display

You might also like