GRP Infrastructure

Water & Sewage Pipes

and Fittings
Preface

2-3 History 24 GRP Pipe Chemical Table

4-5 GRP Pipe Advantages 25 Installation Procedures
6-7 GRP Pipe Properties 26 Standart Drain
8-9 GRP Pipe Diameter and Weight Table 27 - 28 Genarating Drain Filling
10 - 11 GRP Coupling and Properties 29 Above Pipe Compress
12 - 13 GRP Coupling 30 - 31 Installation of Couplings with Elastomer Gasket
14 - 15 Performance Standards 32 GRP Pipe and Fittings
16 - 17 Performance Test and Standards 33 Equal Tee Fittings
18 Controls 34 - 36 Unequal Tee Fittings
19 Quality Control 37 Elbows
20 Performance Tests and Quality Control 38 Flanges
21 Rigidity Classification and Pressure Class 39 Reductions
22 - 23 Engineering Service and Velocity of Wave 40 WYE (Angled Tee)
Propagation
41 - 45 Certificates and Documents
Prestigious company with its Potable Water,
Waste Water, Drainage, Natural Gas,
Telecommunication pipes and fittings
Esen Plastik, with its continuous investments,
presents products ranges above 2000 types to
global market.
 2/3

Esen Plastik A.S. has been established by 1976 to manufacture

plastic pipes and fittings.

Esen Plastik A.S. continues its production and all other activities in
its 130,000 m² facilities in İzmir Atatürk Organized Industrial Zone
and Adana Hacı Sabancı Organized Industrial Zone

Esen Plastik A.S. continues to be a pioneer in the market by adding

advanced production technologies and market demands to its
existing product range. By investing on developing production
technologies; Esen Plastik A.S. serves with 200,000 tons of capacity
in production plants, generates 600 employees, with its engineers and
employees. Esen Plastik A.S. has employed 20,000 people in Turkey.

GRP Pipes for Infrastructure

HDPE Corrugated Sewage Pipes and Fittings,
PE 100 Water Network Pipes
PE 32 Water Network Pipes
PE 80 Natural Gas Pipes
HDPE Telecommunication Data Pipes
HDPE Microduct Fiberoptic Casing Tubes
PVC Potable Water Pipe
PVC Drainage Pipe

45001:2018
Objective
Esen Plastik A.S. with its factories in İzmir and Adana, aims to become a
leader in the infrastructure sector in the domestic and international
markets and has taken part in very important & remarkable projects and
adopted the main duty of increasing the trust in Turkish goods and its
contribution to the economy of our country.

Esen Plastik A.S. continues its investments with the aim of promoting the
product and service quality it offers to its customers, providing faster and
dynamic service, making production in different regions of our country
close to the market and creating employment for the people of our
country.
 Esen Plastik
GRP Pipe and Fittings
4/5

Esen Plastik GRP Pipes are manufactured from 200 mm to 4000

mm diameter in accordance with international standards. Esen GRP
pressurized and unpressurized pipes are used in drinking water,
irrigation water and sewage systems.

Esen Plastik GRP Pipes are highly resistant to chemicals. Resistance

to chemicals varies according to the type of resin used in the pipe.
ESEN GRP Pipes are designed specially according to transported
chemical and the fluid temperature.

GRP PIPE
ADVANTAGES

Esen Plastik GRP Pipes are produced by using composite material

technology using glass fiber, polyester resin and silica sand which
have superior properties in terms of performance, quality and
economy compared to conventional materials.

High corrosion resistance

Lightweight and elastic structure
Superior hydraulic properties
Long service life
Eco-friendly product
High strength structure
Low operating and maintenance costs
Fast and easy installation
Compatibility with ground movements
Economic transportation cost

GRP PIPE
USAGE AREAS

Transmission and distribution lines of irrigation projects

Transmission lines and networks of drinking water plants
Waste water transmission, treatment plant and sea discharge lines
Rain water line
Power plant connection lines
Industrial lines
Road crossing
Renewal of existing pipe lines by pushing

45001:2018
Resistant and
Long Life
Esen Plastik GRP Pipes are manufactured according to AWWA,
ASTM, ISO, EN, BS and TSE standards.

It is used to determine the long-term performance values of the products;

Long Term Tensile Corrosion Test (ASTM3681)

Circular Deviation Strength Test in Wet Conditions (ISO10471)
Long-Term Specific Circle Stiffness (ISO 10468)
It successfully meets stringent tests such as the Long Term Damage Pressure Test
(ASTM 2992). These tests contain the required physical parameters corresponding to a
service life of 50 years.
 Esen Plastik
GRP Pipe and Fittings
6/7

GRP PIPE
PROPERTIES
min. max.
Diameters 200 mm 4000 mm

Stiffness Class ( SN) 500 N/m 2 10.000 N/m 2

Pressure  Class ( PN ) 1 PN 40 PN

* Other classes is available upon request

CHEMICAL
RESISTANCE GUIDE

Esen Plastik GRP Pipes are highly resistant to chemicals. Resist-

ance to chemicals varies according to the type of resin used in the
pipe. ESEN GRP Pipes are specially designed according to the
chemicals to be transported. Please inform Esen Plastik about the
chemical you will carry. Esen Plastik Project Design Team will be
proud to help you.

MIDDLE SURFACE
Resin
OUTER SURFACE Silica Sand
Outer layer Glass Fiber
Resin
Glass Fiber
INNER STRUCTURAL LAYER
Resin
OUTHER Glass Fiber
STRUCTURAL LAYER
Resin INNER SURFACE
Glass Fiber Inner Layer
Resin
Glass Fiber

STANDART RIGIDITY CLASSES STANDARD PRESSURE RANGE

Different SN classes can be produced according to your project. Pipes are manufactured between PN 1 and
The pipes are manufactured in three standard hardness. PN 32 pressure classes.

SN 2500 SN 5000 SN 10000 PN 1 PN 32

 GRP PIPE MINIMUM WALL THICKNESSES (mm)

SN 2500 SN 5000

GRP GRP GRP

Pipe Pipe OD Pipe OD
PN 6 PN 10 PN 16 PN 20 PN 25 PN 32 PN 6 PN 10 PN 16
Nominal Diameter min. max.
(mm) (mm) (mm)

200 206 208 2,50 2,50 2,45 2,45 2,49 2,91 2,98 2,98 2,90
300 309 311 3,30 3,30 3,28 3,25 3,25 3,83 4,02 3,94 3,90
350 359,8 362 3,76 3,74 3,66 3,63 3,64 4,30 4,62 4,62 4,45
400 410,6 413 4,20 4,19 4,08 4,06 4,02 4,75 5,24 5,21 4,97
450 461,4 464 4,71 4,60 4,46 4,43 4,42 5,22 5,88 5,74 5,45
500 512,2 515 5,21 5,03 4,87 4,82 4,82 5,70 6,53 6,28 5,96
600 614 617 6,26 5,89 5,69 5,62 5,64 6,62 7,90 7,41 7,01
700 715,8 719 7,26 6,70 6,46 6,42 6,41 7,54 9,18 8,48 7,98
800 817,6 821 4,98 7,55 7,27 7,21 7,17 8,51 10,47 9,50 9,00
900 921,4 925 9,10 8,37 8,04 7,96 7,98 9,43 11,70 10,68 10,02
1000 1023,4 1028 9,99 9,22 8,85 8,75 8,74 9,55 12,90 11,74 10,88
1100 1125,4 1130 10,88 9,98 9,62 9,54 9,50 11,28 14,02 12,81 12,06
1200 1226,4 1231 11,80 10,82 10,42 10,29 10,27 12,20 15,20 13,86 13,02
1300 1328,9 1333,5 12,87 11,71 11,29 12,72 12,72 13,17 16,50 14,99 14,14
1400 1431,2 1436 13,72 12,45 11,93 11,91 11,88 14,09 17,70 16,12 15,17
1500 1533,2 1538 14,65 13,39 12,82 12,70 12,65 15,01 18,90 17,14 16,09
1600 1635,2 1640 15,57 14,24 13,63 13,50 13,41 15,94 20,09 18,25 17,02
1700 1737,2 1742 16,50 14,99 14,35 14,29 14,18 16,86 21,29 19,25 19,62
1800 1839 1844 17,44 15,84 15,16 14,99 14,94 17,86 22,49 20,38 18,66
1900 1941 1946 18,37 16,70 15,98 15,78 15,78 18,78 23,69 21,50 20,15
2000 2043 2048 19,28 17,46 16,78 16,48 16,55 19,71 24,89 22,51 21,17
2100 2145 2150 20,20 18,21 17,41 17,28 17,31 20,63 26,09 23,50 22,18
2200 2246,8 2252 21,10 19,15 18,31 18,06 18,08 21,55 27,12 24,62 23,10
2300 2347,6 2353 22,01 19,90 19,13 18,86 18,84 22,48 28,31 25,74 24,11
2400 2449,6 2455 22,93 20,75 19,84 19,74 19,60 23,40 29,50 26,86 25,13
2500 2552,6 2558 23,86 21,61 20,66 20,43 20,37 24,32 30,72 27,88 26,15
2600 2654,4 2660 24,78 22,46 21,46 21,22 21,22 25,25 31,92 28,87 27,17
2700 2754,2 2760 25,69 23,20 22,18 22,01 21,98 31,92 28,87 29,98 28,18
2800 2857,2 2863 26,61 23,95 22,99 22,71 21,14 27,09 34,30 31,06 29,20
2900 2959,2 2965 29,31 26,41 25,34 25,07 24,23 29,82 37,80 34,24 32,11
3000 3062 3068 32,01 28,87 27,69 27,43 27,31 32,55 41,30 37,41 35,03
3100 3163,9 3170 32,94 29,76 28,49 28,27 28,12 33,61 42,61 38,59 36,11
3200 3265,8 3272 33,88 30,65 29,28 29,11 28,94 34,66 43,92 39,77 37,19
3300 3367,7 3374 34,91 31,59 30,18 29,96 29,79 35,70 45,27 41,02 38,33
3400 3469,6 3476 35,95 32,54 31,09 30,82 30,64 36,74 46,62 42,26 39,47
3500 3571,6 3578 36,98 33,50 32,00 31,67 31,52 42,31 47,97 43,45 40,62
3600 3673,4 3680 38,02 34,46 32,91 32,53 32,40 47,88 49,32 44,64 41,77
3700 3745,3 3782 34,74 31,34 30,00 29,64 29,58 35,46 44,98 40,69 38,07
3800 3877,2 3884 40,09 36,22 34,60 34,36 34,16 40,95 52,01 46,99 44,06
3900 3979,1 3986 41,13 37,17 35,51 35,22 35,01 41,99 53,36 48,25 45,20
4000 4081 4088 42,17 38,13 36,42 36,08 35,86 43,03 54,71 49,51 46,34
The tables are provided for informational purposes
 GRP PIPE MINIMUM WALL THICKNESSES (mm)
WEIGHT
SN 5000 SN SN
10000
2500

PN 20 PN 25 PN 32 PN 6 PN 10 PN 16 PN 20 PN 25 PN 32 MIN. MAX.
(kg/mt) (kg/mt)

2,88 2,86 2,91 3,60 4,40 3,49 3,45 3,39 2,49 2,82 5,43
3,87 3,86 4,96 4,96 4,96 4,82 4,74 4,68 4,63 5,66 11,30
4,41 4,37 4,35 5,75 5,75 5,46 5,36 5,31 5,26 7,46 15,38
4,90 4,86 4,84 6,57 6,55 6,12 6,00 6,02 5,88 9,58 20,13
5,39 5,37 5,32 7,40 7,30 6,78 6,64 6,54 6,50 11,83 25,63
5,88 5,86 5,80 8,24 8,02 7,41 7,26 7,17 7,10 14,39 31,78
6,90 6,85 6,82 9,99 9,45 8,74 8,54 8,42 8,36 20,26 46,50
7,88 7,80 7,80 11,64 10,90 10,05 9,82 9,67 9,59 27,07 65,43
8,90 8,80 8,79 13,30 12,29 11,36 11,06 10,92 10,78 34,78 83,47
9,89 9,82 9,78 13,29 13,75 12,68 12,36 12,18 12,08 43,69 104,98
10,86 10,79 10,73 16,44 15,20 13,99 13,63 13,42 13,27 54,14 128,84
11,83 11,77 11,71 17,91 16,60 15,26 14,91 14,67 14,50 64,06 154,57
12,85 12,74 12,66 19,45 17,96 16,54 16,14 15,82 15,74 75,58 183,08
13,88 13,80 13,73 21,10 19,48 17,91 17,52 17,18 17,02 88,88 215,50
14,76 14,73 14,67 22,65 20,98 19,22 18,75 18,42 18,26 159,19 249,30
15,82 15,74 15,70 24,20 22,38 20,54 19,90 19,67 19,50 182,28 285,57
16,94 16,67 16,65 25,75 23,76 21,83 21,31 20,92 20,74 206,87 324,30
17,87 16,89 17,59 27,31 25,26 23,14 22,54 22,18 21,89 225,10 365,49
18,84 18,62 18,54 28,86 26,65 24,45 23,67 23,41 23,12 260,83 409,13
19,82 19,54 19,57 30,42 28,03 25,66 25,01 24,58 24,36 289,02 455,25
20,78 20,56 20,51 31,97 29,53 26,96 26,34 25,82 25,60 204,05 503,83
21,76 21,58 21,46 33,52 30,93 28,27 27,46 27,07 26,83 224,74 554,86
22,74 22,50 22,39 34,91 32,31 29,48 28,79 28,32 27,98 246,29 605,60
23,62 23,52 23,31 36,45 33,76 30,87 30,11 29,56 29,22 268,58 660,85
24,68 24,44 24,32 38,00 35,06 32,19 31,35 30,82 30,46 291,77 719,12
25,75 25,38 26,13 39,57 36,58 33,50 32,58 32,05 31,70 316,05 780,60
26,73 26,47 26,36 41,12 37,72 34,86 33,91 33,22 32,93 342,55 843,71
27,69 27,40 27,18 42,64 39,34 35,99 35,14 34,46 34,16 368,36 908,00
28,67 28,42 28,23 44,21 40,84 37,30 36,37 35,71 35,32 399,86 976,81
31,51 31,29 31,05 47,38 44,96 41,11 40,09 39,35 38,92 426,32 1046,97
34,34 34,16 33,88 50,54 49,08 44,92 43,80 42,99 42,52 452,77 1117,12
35,51 35,24 34,96 53,60 50,67 46,34 45,16 44,36 43,85 481,61 1193,04
36,67 36,31 36,05 56,66 52,25 47,75 46,51 45,72 45,19 510,46 1268,96
37,72 37,35 37,15 58,41 53,86 49,23 47,93 47,09 46,61 542,49 1350,34
38,78 38,39 38,25 60,16 55,46 50,70 49,36 48,46 48,03 574,52 1431,72
39,91 39,50 39,35 61,90 57,06 52,16 50,77 49,90 49,39 609,06 1518,02
41,04 40,61 40,46 63,65 58,66 53,63 52,19 51,34 50,75 643,61 1604,31
37,42 37,14 36,90 57,27 53,49 48,91 47,73 46,78 46,32 679,63 1692,74
43,31 42,75 42,65 67,14 61,87 56,57 55,04 54,05 53,47 720,82 1786,71
44,37 43,90 43,72 68,89 63,47 57,98 56,46 55,43 54,90 756,50 1882,82
45,42 45,05 44,79 70,63 65,07 59,38 57,88 56,81 56,32 792,18 1978,93
The tables are provided for informational purposes
ESEN PLASTİK
GRP COUPLING PROPERTIES
Esen Plastik GRP pipe couplings use EPDM seals
which are not deformed. Resistant to chemicals.
Precise sealing with excellent dimension tolerances.
 Esen Plastik
GRP Coupling Properties
10 / 11

Glass reinforced plastic pipes are attached with pressure and

non-pressurized lines and with coupling connection system which
provides precise sealing. Couplings are produced using the same
raw materials and the same process technique as Standard GRP
pipes. Connection sleeves produced from GRP pipes are processed
in sleeve manufacturing machine and slots are opened according to
EPDM REKA seal and stopper tolerances. Esen Plastik EPDM seals
provide double sided sealing with its special structure.

Nominal Outer Coupling Weight Nominal Outer Coupling Weight

Diameter Diameter Diameter Diameter
Lenght MİN. Lenght MİN.
DN MAX. DN MAX.
(mm) (mm) (mm) (kg/mt) (mm) (mm) (mm) (kg/mt)

200 257,4 270 5,17 2000 2154,9 330 91,61

300 358,8 270 9,28 2100 2259,9 330 97,83
350 413,1 270 11,34 2200 2365,0 330 104,21
400 465,1 270 12,84 2300 2469,0 330 110,23
450 518,8 270 14,93 2400 2574,1 330 116,91
500 572,2 270 17,06 2500 2680,2 330 138,70
600 676,3 330 24,79 2600 2785,2 360 159,88
700 780,3 330 28,73 2700 2888,2 360 168,52
800 886,4 330 34,20 2800 2994,3 360 176,83
900 992,5 330 38,40 2900 3099,9 360 183,07
1000 1097,5 330 42,57 3000 3205,5 360 189,30
1100 1202,6 330 47,84 3100 3310,6 360 198,33
1200 1306,6 330 50,11 3200 3415,8 360 207,36
1300 1418,8 330 53,37 3300 3521,1 360 224,04
1400 1524,5 330 58,53 3400 3626,4 380 240,72
1500 1629,6 330 63,54 3500 3731,8 380 252,01
1600 1734,6 330 69,00 3600 3837,1 400 276,74
1700 1839,7 330 74,62 3700 3942,4 400 289,11
1800 1944,7 330 80,02 3800 4047,8 400 301,74
1900 2049,8 330 85,94 3900 4153,1 400 314,74
4000 4258,5 400 327,75

Datas have been arranged as 6 BAR for informational purposes

Esen Plastik has a right to change the technical details acc. to projects.
Esen Plastik
GRP Coupling

Esen Plastik GRP couplings are produced using the same

raw materials and same production technique as GRP
Pipes. The sealing grooves of the produced couplings are
opened with full dimension tolerances in fully automatic
machines and the elastomeric EPDM REKA seals are
installed to ensure precise sealing.

Esen Plastik GRP sleeves allow perfect angular deviations

in the laying stage with excellent dimension and working
tolerance range. These angular deviations are as follow.

Pressure (PN) Bar

Nominal Pipe
Diameter (mm) Nominal Angular Deflection (Degree)
1-16 20 25 32
DN≤ 500 3 2,5 2 1,5
500<DN≤900 2 1,5 1,3 1
900<DN≤1800 1 0,8 0,5 0,5
DN<1800 0,5 NA NA NA

Nom. Offset (mm) Nom. Radius

Nominal Nominal of Curvature (m)
Pipe Angular
Diameter Deflection Pipe Lenght Pipe Lenght
(mm) (Degree)
3(m) 6(m) 12(m) 3(m) 6(m) 12(m)
DN≤ 500 3 157 314 628 57 115 229
500<DN≤900 2 106 208 419 86 172 344
900<DN≤1800 1 52 105 209 172 344 688
DN<1800 0,5 26 52 105 344 688 1376

Esen Plastik Elastomeric EPDM REKA seals provide safer

installation simplicity compared to others and provide absolute
water tightness even at high pressures

Pipe

Offset

Coupling Radius of
Curvature
Angular
Deflection
 Esen Plastik
GRP Coupling
12 / 13

Compared to other couplings manufactured with different machines

and different production techniques, Esen Plastik GRP Couplings
provide easier and safer installation in all weather conditions and all
kinds of ground conditions. Compared to other systems, Esen Plastik
GRP Couplings have the same flexural properties as the pipes.

The cross section of the Esen Plastik GRP Coupling is as shown in the
picture above before pressure is applied to the pipeline.

You can see the cross section of the Esen Plastik GRP Coupling and
the state of the pipeline after the pressure is applied in the picture
above.

Elastomeric Epdm Reka Seals; with excellent dimension tolerance, the

sealing ring is pressed against the sleeve wall.

The stopper part located between the two seals prevents the ends of
the two pipes from hitting each other during damage.

45001:2018
Performance
Standards
Standards developed by ASTM, AWWA and ISO;
This includes a range of glass fiber reinforced pipe
applications, including water, domestic wastewater, and
chemical transport. The common point of all these standards
is that they are all performance-based. In other words, the
performance tests required for GRP Pipe are determined in
these standards.
 Performance
Standards
14 / 15

Standard Concept Standard Concept

AWWA C950 Potable Water Pipe EN14364 Drainage and Waste Water Pipe
AWWA M45 GRP Design Guide ASTM D3262 Unpressurized Waste Water Pipe
ISO 10639 Potable Water Pipe ASTM D3517 Potable Water Pipe
ISO10467 Drainage and Waste Water Pipe ASTM D3754 Pressurized Waste Water Pipe
EN 1796 Potable Water Pipe BS 5480 Potable or Waste Water Pipe

ASTM:

Nowadays there are different ASTM Product Standards used for

various glass fiber reinforced pipe applications. Hydrostatic pressure
test (ASTM D4161) is applied to flexible connection pipes with diameters
from 200 mm to 3700 mm to simulate the operating condition.
These standards include many quality control and qualification tests.
Esen Plastik GRP Pipe has the capacity to meet the requirements of
all these ASTM standards.

AWWA:

AWWA C950 is one of the most comprehensive product standards

for glass fiber reinforced pipes. This standard includes comprehensive
requirements for quality control and prototype proficiency testing for
pipes and fittings to be used in pressurized waterline applications.
Esen Plastik GRP Pipe is designed to meet the performance require-
ments of this standard. A new AWWA M-45 booklet contains several
sections that include the design of GRP pipes laid underground and
above ground.

EN: ISO:

This product standard applies to GRP This product standard applies to GRP pipes used in water and
pipes used in water and wastewater wastewater transportation applications between 50 mm and 4000
transportation applications with mm in diameter. It covers pipes of 5 stiffness (SN630 - SN1250
diameters from 100mm to 4000mm. -SN2500-SN5000 and SN10000) for proficiency tests and all product
tests for pipes and sleeves and operating pressures from 1 bar to 32
Esen Plastik GRP pipe has been bar. Esen Plastik GRP Pipe is designed to meet the requirements of
designed to meet the requirements of this standard.
this standard.

45001:2018
Performance
Tests

The minimum performance requirements of the pipe

proof of suitability by sampling;

The minimum performance requirements for all

standards GRP pipes are both short and long term

Connection
Ring Deflection
Long Term Pressure Strength
Corrosion Resistance Capacity

Esen Plastik performs the tests of “TS EN 1796, TS

EN 14364, ASTM D3517, ASTM D3262, ASTM D3754,
AWWA C950, DIN16869, ISO 10467 and ISO 10639”
Standards in ISO 17025 Accredited Laboratory to
meet the requirements.
Performance
Tests
16 / 17

RAW MATERIALS :

The raw materials are supplied with certifications conforming to the

quality criteria set by Esen Plastik. In addition, all raw materials are
subjected to sample tests prior to production. With these tests, it is
determined that the raw materials are in compliance with the relevant
standards and the criteria of Esen Plastik GRP laboratory.

GLASS FIBER :

Direct Winding Roving; The cylindrical package is supplied in coils such

that the yarn structures are not damaged.

Cropable Wick; unidirectional continuous fibers. Reinforced glass fibers;

The adhesive is held together by means of resin. Fibers of different
thicknesses, weights and widths are available. Thanks to the tulle
structures on the surface, layers with high resin content are formed.

RESIN :

The polyester resins are dissolved in styrene monomer. Thus, the

cross-linking of the resin to the final thermoset structure is achieved.
Organic peroxide catalyst is used to cure the polyester resin

SILICA SAND :

Silica Sand is used to increase pipe rigidity and the pipe is located
around the neutral axis, the sand used generally has a high silica
content.
Controls

The circumferential and axial load carrying capacities

of the produced pipes are proved by routine tests. In
addition, the pipe structure and composition are
checked and approved by tests

Controls during manufacturing process;

Visual Inspection
Barcol Hardness
Wall Thickness Measurement
Pipe Length Measurement
Outer Diameter Measurement
Hydrostatic Leak Test

Inspections by taking samples;

Pipe Stiffness
Structural damage deflection test
without any damage
Strapping Tensile Strength
Axial Tensile Strength
 Performance Tests
and Quality Control
18 / 19

QUALITY CONTROL

Esen Plastik GRP Pipe production technology includes detailed

quality control program. The compliance of the production and tests
of pipes and fittings with international standards and Turkish standards
is ensured with this program.

QUALITY CONTROL TESTS

Raw materials are tested before production. Tests include the

compliance of raw materials and manufactured products (pipe,
coupling, fittings) with standards. These tests ensure that the pipe
materials used comply with the specified standards.

In Esen Plastik A.S. certification works in accordance with ISO

9001 standards that are provided with the total quality approach
implemented with the mutual participation of all employees.

Measured Qualifications Limits of Change

Wall thickness of pipes %10 of the specified thickness of a single point

Visual Inspection Standard
Pipe Length ± 60 mm
Pipe Diameter EN 1796, EN 14364, ISO 10467, AWWA C950 relevant outer
diameter series conforms with (Seri – 1) table

Pipe Stiffness Min. 33 Barcol

Pipe Rigidity ASTM D-2412, EN 1228, ISO 7685 Standard
Pipe Axial Tensile Strength EN 1393, ISO 8513 Standard
Pipe Circle Tensile Strenght EN 1394, ISO 8521 Standard
Layer Adhesion ASTM Standart D-2584 Standard

Classification of pipes according to working pressure is done according to C 950 Standard project
criteria in AWWA and project characteristics in M45

45001:2018
 PERFORMANCE TESTS
and QUALITY CONTROL

Controlling Process Frequency

RAW MATERIALS

Polyester resin Each lot

Sand Each lot
Chop / Hoop ( Glass Fiber Products ) Each lot
Seal / Stopper Stiffness Each lot
Seal / Stopper Dimension Each lot

Visual Control, Pipe ends Each lot

VISUAL CONTROL

Visual Control, Inner and outer surface Each lot

Visual Control, Coupling inner and outer surface, coupling conduit Each Coupling
Visual Control, Fittings Each Fitting
Visual Control, Marking ( Pipe coupling, fittings ) Each Pipe, Coupling, Fittings
Visual Control – Coupling Installation Each connection with Coupling
DIMENSIONAL CONTROL

Pipe/Coupling Inner Diameters Control By the beginning of production

Pipe Wall Thickness Control Each Pipe
Pipe Outer Diameter Each Pipe
Pipe DOS, Chamfering and Calibration Control Each Pipe
Pipe Length Each Pipe
Fittings Dimensional Control Each Fittings
(Length, DOS, Angle, Chamfering and Calibration)

Rigidity Test Once a day or in each 50 pcs pipe

TECHNICAL PARAMETERS

Crack Control in Inner Surface - Test A Once a day or in each 50 pcs pipe
Delamination Control - Test B Once a day or in each 50 pcs pipe
Surface Stiffness Each Pipe
Axial Tensile Strength Once a day or in each 50 pcs pipe
Ring Tensile Strength Once a day or in each 50 pcs pipe
Pipe Leakage Test Each pipe
Composite Test Once a day or in each 50 pcs pipe
Impact Resistance Test In each Shift
Water Absorbtion Test Once a day or in each 50 pcs pipe

Long Term Tensile Corrosion Test Type Test

LONG TERM

Deviation from Circularity Strength Test in Wet Consitions Type Test

Long Term Specific Ring Stiffness
TESTS

Type Test
Long Term Impact Pressure Test Type Test
 Performance
Standards
20 / 21

RIGIDITY CLASSIFICATION

Nominal rigidity values in ISO and AWWA C950 standards;

ISO AWWA

SN 1250 9 psi
SN 2500 18 psi
SN 5000 36 psi
SN 10000 72 psi

Long Term Rigidity : ISO No requirements for long-term stiffness

have been specified in ISO and AWWA

PRESSURE CLASSES

In ISO, pressure classes (PN) are made by accepting them in the bar
unit to be applied. Nominal pressure classes:1, (2,5) ,(4), 6, (9) ,10,
(12), (15), 16, (18), (20), 25, 32

In AWWA C950, the GRP rated pressures are classified as follows.

Psi 50, 100, 150, 200, 250

DEFLECTION RATIOS:

ISO and AWWA C950 have the same initial deflection requirements.
The same classification system is valid in standard.

Class Level A Level B Class Level A Level B

SN 500 24,4 40,8 SN 2500 14,3 23,9

SN 625 22,7 37,8 SN 4000 12,2 20,4
SN 1000 19,4 32,4 SN 5000 11,3 18,9
SN 1250 18,0 30,0 SN 8000 9,7 16,2
SN 2000 15,4 25,7 SN 10000 9,0 15,0
Our Expert
Engineering Staff
Esen Plastik A.S. Provides engineering support to
its customers before and after procurement in
order to use the product and technology accu-
rately and efficiently.
 Engineering
Services
22 / 23

SURGE WAVE CELERITY Esen Plastik with its expert engineers, supports its customers by
considering the highest benefit in all stages of the projects.

SN 2500
Engineering services provided by Esen Plastik:
DN 300 400 450 800 ≥900
PN 6 m/s 430 390 380 360 350
PN 10 m/s 430 420 420 410 400
Hydraulic calculations
PN 16 m/s 520 510 510 500 490
Concrete fixing mass calculations
PN 20 m/s 570 550 550 540 530 Connections with different materials
PN 25 m/s 580 570 570 560 550 Stress analysis of pipelines
Technical and isometry drawings
Field engineering services
SN 5000 Supervisor service
DN 300 400 450 800 ≥900
PN 6 m/s 440 420 390 370 370
PN 10 m/s 450 440 440 430 420
PN 16 m/s 510 490 500 480 480
PN 20 m/s 550 530 530 520 510
PN 25 m/s 580 570 570 560 550

SN 10000
DN 300 400 450 800 ≥900 COMPOSITE MATERIAL
PN 6 m/s 490 470 460 440 430 TECHNOLOGY
PN 10 m/s 470 450 440 420 410
PN 16 m/s 510 500 510 490 480
PN 20 m/s 560 560 550 540 530
Composite Material is the new material that is formed by combining
two or more number of materials , the best properties or combining
PN 25 m/s 570 570 570 560 560 them to create a new feature.

All data are prepared for information purposes With the developing technology and industrialization, the need for
according to 12m pipe. Clear information will materials has enabled the exploration and development of new
vary depending on the pipe laying conditions. composite materials.

Please contact Esen Plastik for clear data. Esen Plastik GRP pipes are composite materials and have all the
superior features of this technology.

45001:2018
 GRP PIPE
Chemical Table
Esen Plastik GRP Pipes are specially designed according to the chemicals to be transported.
Kimyasal
The table below is for informational purposes

Standard Special Standard Special

Chemical GRP Pipe GRP Pipe Chemical GRP Pipe GRP Pipe

Bleached Hydrosulphite Copper Sulphate

Acrylic Acid Barium Hydroxide
Aluminum Oxide Barium Carbonate
Aluminum Chloride Barium Chloride
Aluminum Fluoride Barium Sulfate
Aluminum Hydroxide Benzoic Acid
Aluminum Nitrate Beer
Aluminum Potassium Sulfate Zinc Chlorate
Ammonia Gas Distilled Water
Ammonium Carbonate Sea Water
Amonyum Bisulfat Diesel Fuel
Ammonium Bicarbonate Natural Gas
Ammonium Chloride Ethyl Alcohol
Ammonium Citric Acid Ethylene Glycol
Ammonium Fluoride Ferro Chloride
Ammonium Hydroxide Nitrate Ferro
Ammonium Nitrate Ferro Sulphate
Ammonium Persulfate Phthalic Acid
Ammonium Phosphate Flobonic Acid
Ammonium Sulfate Fluosilic Acid
Analin Sulfat Formic Acid
Acetic Acid Phosphoric Acid
Acidic Chloride Phosphorium Pentoxide
Acid Ferric Nitrate Kerosene
Acid Ferric Sulfat Glycerine
Copper Fluoride Gluconic Acid
Copper Chloride Glucose
Copper Nitrate Crude Oil, Sour
Copper Cyanide Crude Oil, Sweet
Pipe Laying
Procedure
24 / 25

The appropriate installation procedure for GRP Pipe

varies depending on the rigidity of the pipe, the depth
of the trench, the width, the natural soil properties, the
additional loads on the pipeline and the filling material.
In order to support the pipe in a healthy way, the natural
ground should be firmly wrapped around the pipe area
filler. The following pipe installation procedures are
provided to assist in the proper laying of the pipe.
Standard
Trench

It shows the typical trench section dimensions. The dimension

“A” should always be wide enough to ensure that sufficient
filling material can be placed and compacted in the pipe
basin. Dimension“A” should also be wide enough to allow the
clamping equipment to operate in a manner that does not
damage the pipe. Typical ’’ A ’’ size, except for very small
diameters, the minimum is 0.4 DN. For larger diameters, a
smaller value for “A” may be appropriate, depending on the
natural substrate, filler material and compression technique.

For example, in the 1st, 2nd and 3rd groups of natural soils,
the trench can be kept narrower by using SC1 and SC2 fillers
which do not require much compression.

NOTE: If soft, loose, unstable or expanding natural ground is

found on the bottom of the trench, it may be necessary to
increase the thickness of the bearing pad to provide regular
and unchanged support along the pipe.

Trench Width

Pipe Pipe
Basin Zone
 Pipe Trench
Filling
26 / 27

The pipes may float due to heavy rainfall or may be exposed to

thermal expansion, which may result from high temperature
differences between day and night. In order to avoid such noncon-
formities, it is recommended that each pipe, which has been
completed, be filled to the surface level.

If pieces of the pipe is assembled but the filling process will pass;
first, the joints in the middle of each pipe should be filled to the top
to prevent movement. Correct selection and tightening of the pipe
area filler are crucial for controlling vertical deflection and for pipe
performance.

Correct bedding support

Wrong bedding support

Filling
Material Definition of Filling Materials
Group

Crushed stone containing less than 15% sand, maximum

SC1 25% amount of material

SC2 Less than 12% fine grain containing clean coarse materials

Clean coarse materials containing 12% or more fine grains Sandy or

SC3 fine grains containing less than 70% fine grains

SC4 Fine-grained materials containing more than 70% fine-grained piecess

45001:2018
Pipe Trench
Filling

It should be ensured that the filling material does not

contain trash and foreign materials which may damage the
pipe and cause the lateral support to decrease. Located in
the basin region between the bottom of the pipe and the
bearing. The filling and compression of the material must
be carried out before the remaining filling material is
placed. The amount of energy consumed in the compression
method should be checked as well as the thickness of the
compacted fill layer. The appropriate filling process is generally
carried out in layers between 100 mm and 300 mm thickness
depending on the filling material and the compression method.

Gravel or crushed stone is used as filling material, When these

materials are relatively easy to compress. The thickness of the
filler layer is 300 mm. Since thinner materials require more
compression energy, the thickness of the filler layer should be
limited. In order to support the pipe well, it should be ensured
that each filling layer is well compacted.

CORRECT WRONG

Providing appropriate Inappropriate basin

basin support. support.
 On-Pipe
Compression
28 / 29

When it reaches the top of the pipe, it should not exceed 1.5% of
the pipe diameter. This initial amount of ovalization will depend
on the amount of energy required to achieve the desired relative
degree of compression. High amounts of energy required for
SC3 and SC4 fillers can cause this ovalization limit to be
exceeded. In this case, can be considered the use of pipes or
other filling materials of higher rigidity.

Hand Hand
Operated Operated
Filler Type Impact Vibratory Suggestions
Compactor Plate Compactor

Type SC1 Tip SC1 Two-time transition provides a good compression.

Type SC2 Tip SC2 2-4 transitions depending on desired density and height.
The number of transition and layer height depends on the
desired density.
Type SC3 100 - 200 mm Optimal or close moisture content.
Check compression.

It may require high compression energy. Check that if

Type SC4 100 - 150 mm the moisture content is ideal. Make sure that the
compression is done correctly.

With the Type 1 mounting version, the pipe area up to 300

mm in height must be tightened. In areas that will be
Permissible initial Vertical Deflection subject to traffic load, the trench filler is compacted to the
vertical deflection values ( of Diameter %) natural ground to minimize road surface settlements. It
Large Diameter (DN 300)
provides the thickness of the soil cover on the pipe required
Beginning 3 for the operation of various compaction equipment on the
Small Diameter (DN 250)
pipe. Care should be taken not to apply high compression
2 energy to the top of the pipe, which may cause deformity of
Beginning
the pipe circularity. At the same time, the material in this
section should not be left loose and should be reached to
TRAFFIC LOADS the desired density.

Depth of
Loads Type
Strength Strength
(Kn) (Ibs)
Embedment WATER - HAMMER IMPACT :
(m)

AASHTO H20 ( C ) 72 16000 1

The impact of the water-hammer is a change in the flow
BS 153 HA ( C ) 90 20000 1,5
rate of pipe systems caused by the sudden decrease or
ATV LKW 12 ( C ) 40 9000 1 increase of the system pressure. These changes are
ATV SLW 30 ( C ) 50 11000 1 caused by sudden opening and closing of the valves,
sudden stopping of the pumps in the event of a power
ATV SLW 60 ( C ) 100 22000 1,5
failure or sudden operation during commissioning. The
Cooper E80 Demiryolu 3 water-hammer pressure in the GRP pipes and steel and
ductile pipes are is 49.9% . The water-hammer impact
Minimum pipe area filling floor module is
pressure in GRP pipes is approximately 39.9% of the rated
taken as 6.9 Mpa
pressure. The water-hammer stroke is calculated by the
following formula.

∆H= (W*∆V)/g
∆H : Change in pressure (m) w: Surge wave celerity (m/sn)
∆V : Change in fluid velocity (m/sn) g: Gravitational acceleration (m/sn²)
Double Sided
Elastomer Sealed
Coupling Mounting
Double Sided
Elastomer Sealed
Coupling Mounting
30 / 31

A - REKA COUPLING

The following steps (1-5) must be followed when fitting the

Reka couplings.

Step 1 Foundation and Bearing

The bearing should be dug in such a way that at each point of the
coupling, the head rests on the coupling to prevent it from hanging
and to ensure continuous support of the pipe. After the jointing
process is completed, the filling and bearing of the coupling area
should be made properly.

Step 2 Cleaning the Coupling

The grooves of the double-sided couplings and the Epdm Reka seal
to be placed in the couplings should be thoroughly cleaned until
they are clear of dirt and oil.

Step 3 Installing the Seals

The elastomer seal is placed in the groove of the coupling such that
the protrusions of the Epdm Reka seal are facing out of the groove.
Do not apply lubricant into the groove or on the seal during gasket
installation. However, the seal duct can be moistened with water for
easy installation of the seals.

Step 4 Apply Lubricant to Elastomer Seal

Then apply a thin layer of lubricant to Epdm Reka Seal. The amount
of lubricant that should be used in each coupling must be kept
constant.

Step 5 Cleaning the Pipe Opening and Applying Lubricant

The pipe opening that will pass into the coupling must be
cleaned from sand, dust, dirt and oil. Check the sealing surface
of the pipe opening for any damage. Apply a thin layer of
lubricant to the area of the pipe up to the Pieces marked with a
black strip. Make sure that the coupling and the pipe opening
remain clean after the lubricant has been applied. A plastic
sheet of approximately 1 m² or a clean cloth to be placed under the
jointing area has been found to be an effective way of ensuring that
the pipe ends and seals remain clean.
 Esen GRP Pipe
and Fittings

REDUCER FLANGE

A L=2.5 x (DL-DS) B

DN

DS DL
t
H
LL

F
A L=2.5 x (DL-DS) B
Smooth Flange

DS DL

ELBOW
LL

R
TEE PIECES
α
L
L

C PIECES - WYE (Angled Tee)

L

DL

B
Ds
 D D

H H
Equal TEE Pieces
D D

GRP FITTINGS
32 / 33
B B

L L

D PN ( 1 - 6 ) PN 10 PN 16
(mm) L (max.) mm H (max.)mm L (max.)mm H (max.)mm L (max.)mm H (max.)mm
300 1000,4 450,4 1000,4 450,4 1200,4 550,4
350 1200,4 530,4 1200,4 530,4 1400,4 630,4
400 1300,4 610,4 1300,4 610,4 1500,4 690,4
450 1400,4 660,4 1400,4 660,4 1600,4 740,4
500 1500,4 720,4 1500,4 720,4 1700,4 820,4
600 1700,4 790,4 1700,4 790,4 1800,4 870,4
700 1900,4 870,4 1900,4 870,4 2100,4 990,4
800 2100,4 970,4 2100,4 970,4 2400,4 1120,4
900 2200,4 1050,4 2200,4 1050,4 2600,4 1250,4
1000 2400,4 1150,4 2400,4 1150,4 2800,4 1350,4
1100 2600,4 1220,4 2600,4 1220,4 3000,4 1450,4
1200 2800,4 1320,4 2800,4 1320,4 3200,4 1550,4
1300 2900,4 1400,4 2900,4 1400,4 3500,4 1680,4
1400 3100,4 1480,4 3100,4 1480,4 3700,4 1780,4
1500 3300,4 1590,4 3300,4 1590,4 3900,4 1890,4
1600 3400,4 1660,4 3400,4 1660,4 4100,4 2010,4
1700 3600,4 1740,4 3600,4 1740,4 4300,4 2110,4
1800 3700,4 1810,4 3700,4 1810,4 4500,4 2210,4
1900 3900,4 1890,4 3900,4 1890,4 4800,4 2340,4
2000 4000,4 1970,4 4000,4 1970,4 5000,4 2470,4
2100 4200,4 2040,4 4200,4 2040,4 5200,4 2540,4
2200 4300,4 2120,4 4300,4 2120,4 5300,4 2620,4
2300 4500,4 2190,4 4500,4 2190,4 5600,4 2740,4
2400 4600,4 2270,4 4600,4 2270,4 5700,4 2790,4
2500 4800,4 2370,4 4800,4 2370,4 5900,4 2900,4
2600 5000,4 2450,4 5000,4 2450,4 6100,4 3000,4
2700 5100,4 2520,4 5100,4 2520,4 6200,4 3070,4
2800 5300,4 2600,4 5300,4 2600,4 6400,4 3150,4
2900 5400,4 2680,4 5400,4 2680,4 6600,4 3250,4
3000 5600,4 2750,4 5600,4 2750,4 6700,4 3300,4
3100 5700,4 2830,4 5700,4 2830,4 6900,4 3400,4
3200 5900,4 2900,4 5900,4 2900,4 7100,4 3500,4
3300 6100,4 3010,4 6100,4 3010,4 − −
3400 6300,4 3130,4 6300,4 3130,4 − −
3500 6500,4 3230,4 6500,4 3230,4 − −
3600 6600,4 3280,4 6600,4 3280,4 − −
3700 6800,4 3380,4 6800,4 3380,4 − −
3800 7000,4 3460,4 7000,4 3460,4 − −
3900 7100,4 3540,4 7100,4 3540,4 − −
4000 7300,4 3610,4 7300,4 3610,4 − −
Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
 d d

Unequal
H H
TEE Pieces D D

GRP FITTINGS B B

L max L max

D d PN ( 1 - 6 ) PN 10 PN 16
(mm) (mm) L (max.)mm H (max.)mm L (max.)mm H (max.)mm L (max.)mm H (max.)mm
150 800,4 400,4 800,4 400,4 800,4 430,4
300 200 900,4 430,4 900,4 430,4 1000,4 480,4
250 900,4 430,4 900,4 430,4 1000,4 480,4
150 800,4 430,4 800,4 430,4 800,4 450,4
350 200 900,4 450,4 900,4 450,4 1000,4 500,4
250 900,4 450,4 900,4 450,4 1000,4 500,4
150 800,4 460,4 800,4 460,4 800,4 490,4
400 200 900,4 490,4 900,4 490,4 1000,4 540,4
250 900,4 490,4 900,4 490,4 1000,4 540,4
150 800,4 480,4 800,4 480,4 800,4 510,4
450 200 900,4 510,4 900,4 510,4 1000,4 590,4
250 900,4 510,4 900,4 510,4 1100,4 590,4
150 800,4 510,4 800,4 510,4 800,4 540,4
500 200 900,4 540,4 900,4 540,4 1000,4 620,4
250 1000,4 570,4 1000,4 570,4 1100,4 640,4
300 1000,4 620,4 1000,4 620,4 1200,4 720,4
600 400 1300,4 720,4 1300,4 720,4 1500,4 790,4
450 1400,4 740,4 1400,4 740,4 1600,4 820,4
200 900,4 660,4 900,4 660,4 1000,4 690,4
700 400 1400,4 790,4 1400,4 790,4 1600,4 890,4
600 1800,4 870,4 1800,4 870,4 2000,4 970,4
200 900,4 710,4 900,4 710,4 1000,4 760,4
800 400 1500,4 870,4 1500,4 870,4 1700,4 990,4
600 1800,4 940,4 1800,4 940,4 2100,4 1070,4
300 1300,4 870,4 1300,4 870,4 1500,4 1000,4
900 500 1700,4 1000,4 1700,4 1000,4 2000,4 1120,4
800 2100,4 1050,4 2100,4 1050,4 2400,4 1200,4
300 1300,4 950,4 1300,4 950,4 1600,4 1100,4
1000 500 1800,4 1070,4 1800,4 1070,4 2100,4 1220,4
800 2200,4 1120,4 2200,4 1120,4 2500,4 1300,4
500 1700,4 1150,4 1700,4 1150,4 2000,4 1300,4
1100 800 2100,4 1200,4 2100,4 1200,4 2500,4 1370,4
1000 2400,4 1220,4 2400,4 1220,4 2800,4 1420,4
500 1800,4 1220,4 1800,4 1220,4 2100,4 1370,4
1200 800 2200,4 1270,4 2200,4 1270,4 2500,4 1450,4
1000 2400,4 1300,4 2400,4 1300,4 2800,4 1300,4

Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
 d d

H H Unequal
D D
TEE Pieces
GRP FITTINGS
B B 34 / 35
L max L max

D d PN ( 1 - 6 ) PN 10 PN 16
(mm) (mm) L (max.)mm H (max.)mm L (max.)mm H (max.)mm L (max.)mm H (max.)mm
500 1800,4 1300,4 1800,4 1300,4 2200,4 1480,4
1300 800 2200,4 1350,4 2200,4 1350,4 2600,4 1550,4
1000 2500,4 1380,4 2500,4 1380,4 2900,4 1600,4
500 1800,4 1360,4 1800,4 1360,4 2200,4 1560,4
1400 800 2200,4 1410,4 2200,4 1410,4 2700,4 1630,4
1000 2500,4 1430,4 2500,4 1430,4 3000,4 1680,4
500 1900,4 1440,4 1900,4 1440,4 2300,4 1640,4
1500 800 2300,4 1490,4 2300,4 1490,4 2700,4 1710,4
1000 2600,4 1510,4 2600,4 1510,4 3000,4 1760,4
500 1900,4 1510,4 1900,4 1510,4 2400,4 1740,4
1600 800 2300,4 1560,4 2300,4 1560,4 2800,4 1810,4
1000 2600,4 1590,4 2600,4 1590,4 3100,4 1860,4
500 1900,4 1560,4 1900,4 1560,4 2400,4 1810,4
1700 800 2300,4 1610,4 2300,4 1610,4 2900,4 1890,4
1000 2600,4 1640,4 2600,4 1640,4 3200,4 1940,4
500 2000,4 1640,4 2000,4 1640,4 2500,4 1890,4
1800 800 2400,4 1690,4 2400,4 1690,4 2900,4 1960,4
1000 2600,4 1710,4 2600,4 1710,4 3200,4 2010,4
500 2000,4 1690,4 2000,4 1690,4 2500,4 1960,4
1900 800 2400,4 1740,4 2400,4 1740,4 3000,4 2040,4
1000 2600,4 1760,4 2600,4 1760,4 3300,4 2090,4
500 2000,4 1770,4 2000,4 1770,4 2600,4 2040,4
2000 800 2400,4 1820,4 2400,4 1820,4 3000,4 2120,4
1000 2700,4 1840,4 2700,4 1840,4 3300,4 2170,4
800 2400,4 1870,4 2400,4 1870,4 3000,4 2170,4
2100 1000 2700,4 1890,4 2700,4 1890,4 3300,4 2220,4
1200 3000,4 1920,4 3000,4 1920,4 3600,4 2270,4
800 2500,4 1940,4 2500,4 1940,4 3000,4 2220,4
2200 1000 2700,4 1970,4 2700,4 1970,4 3300,4 2270,4
1200 3000,4 1990,4 3000,4 1990,4 3600,4 2320,4
800 2500,4 1990,4 2500,4 1990,4 3100,4 2320,4
2300 1000 2700,4 2020,4 2700,4 2020,4 3400,4 2370,4
1200 3000,4 2040,4 3000,4 2040,4 3700,4 2420,4
1200 3000,4 2120,4 3000,4 2120,4 3700,4 2470,4
2400 1600 3500,4 2170,4 3500,4 2170,4 4300,4 2570,4
2000 4000,4 2220,4 4000,4 2220,4 5000,4 2720,4
1200 3000,4 2200,4 3000,4 2200,4 3800,4 2550,4
2500 1600 3600,4 2250,4 3600,4 2250,4 4400,4 2650,4
2000 4100,4 2300,4 4100,4 2300,4 5100,4 2800,4
1200 3000,4 2270,4 3000,4 2270,4 3900,4 2650,4
2600 1600 3600,4 2320,4 3600,4 2320,4 4500,4 2750,4
2000 4100,4 2370,4 4100,4 2370,4 5200,4 2900,4

Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
 d d

Unequal
TEE Pieces
H H

D D

GRP FITTINGS B

L max
B

L max

D d PN ( 1 - 6 ) PN 10 PN 16
(mm) (mm) L (max.)mm H (max.)mm L (max.)mm H (max.)mm L (max.)mm H (max.)mm
1000 3000,4 2300,4 3000,4 2300,4 3600,4 2650,4
2700 1600 3600,4 2370,4 3600,4 2370,4 4500,4 2800,4
2000 4100,4 2420,4 4100,4 2420,4 5200,4 2950,4
1000 2900,4 2370,4 2900,4 2370,4 3600,4 2700,4
2800 1600 3700,4 2450,4 3700,4 2450,4 4500,4 2850,4
2000 4200,4 2500,4 4200,4 2500,4 5200,4 3000,4
1000 3000,4 2430,4 3000,4 2430,4 3700,4 2800,4
2900 1600 3700,4 2500,4 3700,4 2500,4 4600,4 2950,4
2000 4200,4 2550,4 4200,4 2550,4 5300,4 3100,4
1000 3000,4 2500,4 3000,4 2500,4 3700,4 2850,4
3000 1600 3700,4 2580,4 3700,4 2580,4 4600,4 3000,4
2000 4200,4 2630,4 4200,4 2630,4 5300,4 3150,4
1000 3000,4 2550,4 3000,4 2550,4 3700,4 2900,4
3100 1600 3700,4 2630,4 3700,4 2630,4 4600,4 3050,4
2000 4200,4 2680,4 4200,4 2680,4 5300,4 3200,4
1000 3000,4 2630,4 3000,4 2630,4 3800,4 3000,4
3200 1600 3800,4 2700,4 3800,4 2700,4 4700,4 3150,4
2000 4300,4 2750,4 4300,4 2750,4 5400,4 3300,4
1000 3000,4 2680,4 3000,4 2680,4 − −
3300 1600 3800,4 2760,4 3800,4 2760,4 − −
2000 4300,4 2810,4 4300,4 2810,4 − −
1600 3000,4 2830,4 3000,4 2830,4 − −
3400 2400 4800,4 2930,4 4800,4 2930,4 − −
3000 5600,4 3010,4 5600,4 3010,4 − −
1600 3000,4 2880,4 3000,4 2880,4 − −
3500 2400 4800,4 2980,4 4800,4 2980,4 − −
3000 5600,4 3060,4 5600,4 3060,4 − −
1600 3000,4 2960,4 3000,4 2960,4 − −
3600 2400 4900,4 3060,4 4900,4 3060,4 − −
3000 5600,4 3130,4 5600,4 3130,4 − −
1600 3000,4 3010,4 3000,4 3010,4 − −
3700 2400 4900,4 3110,4 4900,4 3110,4 − −
3000 5600,4 3180,4 5600,4 3180,4 − −
1600 3000,4 3090,4 3000,4 3090,4 − −
3800 2400 4900,4 3190,4 4900,4 3190,4 − −
3000 5700,4 3260,4 5700,4 3260,4 − −
1600 3000,4 3140,4 3000,4 3140,4 − −
3900 2400 4900,4 3240,4 4900,4 3240,4 − −
3000 5700,4 3310,4 5700,4 3310,4 − −
1600 3000,4 3210,4 3000,4 3210,4 − −
4000 2400 5000,4 3310,4 5000,4 3310,4 − −
3000 5700,4 3390,4 5700,4 3390,4 − −

Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
 R

α
L
R
L
Elbows
L

GRP FITTINGS
36 / 37

11.25 22.5 30 45 60 90
DN R L L L L L L
300 450,4 285,4 320,4 320,4 410,4 460,4 660,4
350 450,4 285,4 320,4 320,4 410,4 460,4 660,4
400 525,4 285,4 310,4 310,4 435,4 510,4 710,4
450 600,4 335,4 360,4 360,4 485,4 560,4 810,4
500 675,4 335,4 385,4 385,4 535,4 635,4 960,4
600 750,4 335,4 385,4 385,4 535,4 635,4 960,4
700 900,4 335,4 410,4 410,4 610,4 710,4 1175,4
800 1050,4 410,4 435,4 435,4 660,4 785,4 1200,4
900 1170,4 410,4 460,4 460,4 710,4 860,4 1450,4
1000 1200,4 410,4 485,4 485,4 735,4 885,4 1500,4
1100 1270,4 435,4 510,4 510,4 760,4 935,4 1550,4
1200 1320,4 485,4 535,4 535,4 810,4 1100,4 1650,4
1300 1370,4 485,4 535,4 535,4 835,4 1125,4 1700,4
1400 1420,4 510,4 560,4 560,4 885,4 1175,4 1750,4
1500 1470,4 510,4 585,4 585,4 900,4 1200,4 1800,4
1600 1570,4 560,4 660,4 660,4 1125,4 1350,4 2000,4
1700 1670,4 610,4 685,4 685,4 1200,4 1400,4 2100,4
1800 1770,4 685,4 785,4 785,4 1300,4 1500,4 2300,4
1900 1870,4 685,4 785,4 785,4 1300,4 1600,4 2400,4
2000 1970,4 710,4 810,4 810,4 1400,4 1600,4 2500,4
2100 2070,4 710,4 820,4 820,4 1400,4 1600,4 2500,4
2200 2170,4 785,4 885,4 885,4 1500,4 1700,4 2700,4
2300 2270,4 785,4 885,4 885,4 1600,4 1700,4 2800,4
2400 2370,4 810,4 910,4 910,4 1700,4 1800,4 2900,4
2500 2470,4 810,4 910,4 910,4 1800,4 1800,4 2900,4
2600 2600,4 1100,4 1200,4 1200,4 1800,4 2000,4 3100,4
2700 2700,4 1000,4 1200,4 1200,4 1800,4 2100,4 3100,4
2800 2800,4 1100,4 1200,4 1200,4 1900,4 2200,4 3300,4
2900 2900,4 1100,4 1200,4 1200,4 1900,4 2100,4 3300,4
3000 3000,4 1200,4 1200,4 1200,4 2000,4 2200,4 3500,4
3100 3100,4 1200,4 1300,4 1300,4 2000,4 2200,4 3500,4
3200 3200,4 1300,4 1300,4 1300,4 2100,4 2300,4 3700,4
3300 3300,4 1300,4 1300,4 1300,4 2100,4 2300,4 3700,4
3400 3400,4 1300,4 1400,4 1400,4 2200,4 2400,4 3900,4
3500 3500,4 1300,4 1400,4 1400,4 2200,4 2400,4 3900,4
3600 3600,4 1400,4 1500,4 1500,4 2300,4 2500,4 4100,4
3700 3700,4 1400,4 1500,4 1500,4 2300,4 2600,4 4100,4
3800 3800,4 1500,4 1500,4 1500,4 2400,4 2600,4 4300,4
3900 3900,4 1500,4 1500,4 1500,4 2400,4 2600,4 4300,4
4000 4000,4 1500,4 1500,4 1500,4 2500,4 2700,4 4500,4

Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
 DN

t
H
Flanges

GRP FITTINGS F

Smooth Flange

Nominal PN 0 -16 (bar)

Dia (DN) mm F (mm) T (mm) H (mm)
300 40,4 20,4 700
350 45,4 23,4 700
400 45,4 23,4 700
450 50,4 25,4 700
500 50,4 25,4 700
600 60,4 30,4 1000
700 65,4 33,4 1000
800 70,4 35,4 1000
900 75,4 38,4 1000
1000 80,4 40,4 1000
1100 90,4 45,4 1000
1200 95,4 48,4 1000
1300 100,4 50,4 1000
1400 105,4 53,4 1000
1500 105,4 53,4 1000
1600 110,4 55,4 1000
1700 115,4 58,4 1000
1800 120,4 60,4 1000
1900 125,4 63,4 1000
2000 130,4 65,4 1000
2100 135,4 68,4 1300
2200 140,4 70,4 1300
2300 145,4 73,4 1300
2400 150,4 75,4 1300
2500 160,4 78,4 1300
2600 165,4 81,4 1300
2700 170,4 83,4 1300
2800 175,4 86,4 1300
2900 180,4 88,4 1300
3000 185,4 91,4 1500
3100 190,4 94,4 1500
3200 195,4 97,4 1500
3300 200,4 100,4 1500
3400 205,4 103,4 1500
3500 210,4 106,4 1500
3600 215,4 108,4 1500
3700 220,5 111,4 1500
3800 225,5 114,4 1500
3900 230,5 117,4 1500
4000 235,5 120,4 1500

Fitting length and diameters can be changed according to project specifications.

 A L=2.5 x (DL-DS) B A L=2.5 x (DL-DS) B

DS DL DS DL Reducers

GRP FITTINGS
38 / 39
LL
LL

DL DS A=B L LL DL DS A=B L LL
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)

300 200,4 400,4 250,4 1050,4 2100 1900,4 600,4 500,4 1700,4
300 250,4 400,4 125,4 925,4 2100 2000,4 600,4 250,4 1450,4
350 250,4 400,4 250,4 1050,4 2200 2000,4 600,4 500,4 1700,4
350 300,4 400,4 125,4 925,4 2200 2100,4 600,4 250,4 1450,4
400 300,4 400,4 250,4 1050,4 2300 2100,4 600,4 500,4 1700,4
400 350,4 400,4 125,4 925,4 2300 2200,4 600,4 250,4 1450,4
450 350,4 400,4 250,4 1050,4 2400 2200,4 600,4 500,4 1700,4
450 400,4 400,4 125,4 925,4 2400 2300,4 600,4 250,4 1450,4
500 350,4 400,4 375,4 1175,4 2500 2300,4 750,4 500,4 2000,4
500 400,4 400,4 250,4 1050,4 2500 2400,4 750,4 250,4 1750,4
600 400,4 400,4 500,4 1300,4 2600 2400,4 750,4 500,4 2000,4
600 500,4 400,4 250,4 1050,4 2600 2500,4 750,4 250,4 1750,4
700 500,4 400,4 500,4 1300,4 2700 2500,4 750,4 500,4 2000,4
700 600,4 400,4 250,4 1050,4 2700 2600,4 750,4 250,4 1750,4
800 600,4 400,4 500,4 1300,4 2800 2600,4 750,4 500,4 2000,4
800 700,4 400,4 250,4 1050,4 2800 2700,4 750,4 250,4 1750,4
900 700,4 400,4 500,4 1300,4 2900 2700,4 750,4 500,4 2000,4
900 800,4 400,4 250,4 1050,4 2900 2800,4 750,4 250,4 1750,4
1000 800,4 400,4 500,4 1300,4 3000 2800,4 750,4 500,4 2000,4
1000 900,4 400,4 250,4 1050,4 3000 2900,4 900,4 250,4 1750,4
1100 900,4 400,4 500,4 1300,4 3100 2900,4 900,4 500,4 2300,4
1100 1000,4 400,4 250,4 1050,4 3100 3000,4 900,4 250,4 2050,4
1200 1000,4 500,4 500,4 1500,4 3200 3000,4 900,4 500,4 2300,4
1200 1100,4 500,4 250,4 1250,4 3200 3100,4 900,4 250,4 2050,4
1300 1100,4 500,4 500,4 1500,4 3300 3100,4 900,4 500,4 2300,4
1300 1200,4 500,4 250,4 1250,4 3300 3200,4 900,4 250,4 2050,4
1400 1200,4 500,4 500,4 1500,4 3400 3200,4 900,4 500,4 2300,4
1400 1300,4 500,4 250,4 1250,4 3400 3300,4 900,4 250,4 2050,4
1500 1300,4 500,4 500,4 1500,4 3500 3300,4 1050,4 500,4 2600,4
1500 1400,4 500,4 250,4 1250,4 3500 3400,4 1050,4 250,4 2350,4
1600 1500,4 600,4 250,4 1450,4 3600 3400,4 1050,4 500,4 2600,4
1600 1400,4 600,4 500,4 1700,4 3600 3500,4 1050,4 250,4 2350,4
1700 1500,4 600,4 500,4 1700,4 3700 3500,4 1050,4 500,4 2600,4
1700 1600,4 600,4 250,4 1450,4 3700 3600,4 1050,4 250,4 2350,4
1800 1400,4 600,4 1000,4 2200,4 3700 3600,4 1050,4 500,4 2600,4
1800 1600,4 600,4 500,4 1700,4 3800 3700,4 1050,4 250,4 2350,4
1900 1700,4 600,4 500,4 1700,4 3900 3700,4 1100,4 500,4 2700,4
1900 1800,4 600,4 250,4 1450,4 3900 3800,4 1100,4 250,4 2450,4
2000 1600,4 600,4 1000,4 2200,4 4000 3800,4 1100,4 500,4 2700,4
2000 1800,4 600,4 500,4 1700,4 4000 3900,4 1100,4 250,4 2450,4

Fitting length and diameters can be changed according to project specifications.

 L

WYE (Angled Tee ) DL

GRP FITTINGS

B
Ds

Nominal Nominal Nominal Nominal

Dia DL Dia DS B A L Dia DL Dia DS B A L
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)

300 200 600,4 624,4 1100,4 900 700 1100,4 978,4 1500,4
300 300 700,4 695,4 1200,4 900 800 1200,4 1049,4 1550,4
350 250 650,4 660,4 1200,4 900 900 1300,4 1119,4 1600,4
350 300 700,4 695,4 1200,4 1000 800 1200,4 1049,4 1550,4
350 350 750,4 730,4 1200,4 1000 900 1300,4 1119,4 1600,4
400 300 700,4 695,4 1200,4 1000 1000 1400,4 1190,4 1700,4
400 350 750,4 730,4 1200,4 1200 1000 1400,4 1190,4 1700,4
400 400 800,4 766,4 1200,4 1200 1100 1500,4 1261,4 1750,4
450 350 750,4 730,4 1250,4 1200 1200 1600,4 1331,4 1800,4
450 400 800,4 766,4 1250,4 1400 1200 1600,4 1331,4 1850,4
450 450 850,4 801,4 1300,4 1400 1300 1700,4 1402,4 1900,4
500 300 700,4 695,4 1200,4 1400 1400 1800,4 1473,4 1900,4
500 400 800,4 766,4 1250,4 1600 1200 1600,4 1331,4 1850,4
500 500 900,4 836,4 1300,4 1600 1400 1800,4 1473,4 2000,4
600 400 800,4 766,4 1250,4 1600 1600 2000,4 1614,4 2100,4
600 500 900,4 836,4 1350,4 1800 1400 1800,4 1473,4 2000,4
600 600 1000,4 904,4 1400,4 1800 1600 2000,4 1614,4 2100,4
700 500 900,4 836,4 1350,4 1800 1800 2200,4 1756,4 2200,4
700 600 1000,4 907,4 1400,4 2000 1600 2000,4 1614,4 2100,4
700 700 1100,4 978,4 1500,4 2000 1800 2200,4 1756,4 2200,4
800 600 1000,4 907,4 1400,4 2000 2000 2400,4 1897,4 2300,4
800 700 1100,4 978,4 1500,4 2400 1800 2200,4 1756,4 2200,4
800 800 1200,4 1049,4 1550,4 2400 2000 2400,4 1897,4 2400,4
2400 2400 2800,4 2180,4 2600,4

Fitting lengths and diameters may vary according to project pipe length, Pn and project specifications.
Certificates and
Our documents
40 / 41
Certificates and
Our documents
Certificates and
Our documents
42 / 43
Certificates and
Our documents
Certificates and
Our documents
44 / 45
Certificates and
Our documents
 www.esenplastik.com.tr

45001:2018
Izmir Plant:
İzmir Atatürk Organized Industrial Zone
10006 Sk. No:71 B.Çiğli - İzmir / TÜRKİYE
Tel: 0232 376 70 11 Fax: 0232 376 70 10

[email protected]
www.esenplastik.com.tr