Scribd Logo
Upload

Welcome to Scribd!

  • 42 views

    EMCP Electronic Control (AC Transformer Box) - Replace: Pantalla Anterior

    Uploaded by

    Gustavo Pereira
    testes e ajustes 03

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    EMCP Electronic Control (AC Transformer Box) - Replace: Pantalla Anterior

    Uploaded by

    Gustavo Pereira
    42 views3 pages
    testes e ajustes 03

    Original Title

    TESTES E AJUSTES 03

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    testes e ajustes 03

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    42 views3 pages

    EMCP Electronic Control (AC Transformer Box) - Replace: Pantalla Anterior

    Uploaded by

    Gustavo Pereira
    testes e ajustes 03

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    3412C Generator Set 81Z14501-UP(SEBP2576 - 66) - Documentación Página 1 de 3

    Pantalla anterior

    Bienvenido: p230vle

    Producto:  GEN SET ENGINE 
    Modelo:  3412 GEN SET ENGINE 81Z20699 
    Configuración: 3412C Generator Set 81Z14501-UP 

    Pruebas y Ajustes
    Electronic Modular Control Panel II (EMCP II) For MUI Engines
    Número de medio -SENR5809-05 Fecha de publicación -01/10/2001 Fecha de actualización -30/01/2002

    i00946745

    EMCP Electronic Control (AC Transformer Box) - Replace


    SMCS - 1409-510

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 10/09/2018
    3412C Generator Set 81Z14501-UP(SEBP2576 - 66) - Documentación Página 2 de 3

    Illustration 1 g00483140

    AC Transformer Box (ATB)

    The ATB is located on the subpanel within the control panel.

    Replacement Procedure

    1. Shut down the engine. Remove the positive lead wire from the battery.

    2. Make sure that all wires at the terminal strip of the ATB are marked with the respective
    termination point. During reassembly, these wires must be reattached to the correct
    terminal. Remove all external wires from the terminal strip.

    3. Disconnect the ATB connector from the harness connector.

    4. Remove all mounting nuts and mounting screws that fasten the ATB to the subpanel.
    Remove the ATB.

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 10/09/2018
    3412C Generator Set 81Z14501-UP(SEBP2576 - 66) - Documentación Página 3 de 3

    5. Place the new ATB in the subpanel. Install the mounting nuts and mounting screws. Tighten
    the mounting nuts and mounting screws.

    6. Reconnect the harness connector to the ATB. Reconnect all the wires to the terminal strip
    that were removed. Reconnect the positive lead wire to the battery. If necessary, see the
    "Generator Set Wiring Diagram" in Testing And Adjusting, "Schematics and Wiring
    Diagrams".

    7. Program the bar code (calibration value) for the voltmeter/ammeter into the GSC. See
    Systems Operation, "Voltmeter/Ammeter Programming OP8".

    8. If the genset is operating in parallel with another genset and the voltmeter values match,
    then reprogram the AC offset. See Systems Operation, "AC Offset Adjustment OP10".

    Copyright 1993 - 2018 Caterpillar Inc. Mon Sep 10 16:57:49 UTC-0300 2018 
    Todos los derechos reservados. p230vle 
    Red privada para licenciados del SIS.

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 10/09/2018

    You might also like