Scribd
Upload
3K views4 pages

DTC C1249/49 Open in Stop Light Switch Circuit: Description

The document describes a diagnostic trouble code (DTC) related to an open circuit in the stop light switch of a vehicle stability control system. It provides the DTC number, detection conditions, possible trouble areas, inspection procedures to diagnose the issue which include checking fuse integrity, relay resistance, switch resistance, and wire harness connections. The recommended repair is to replace the ABS and traction control actuator assembly if the issue persists after inspections.

Uploaded by

Amil AnAm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views4 pages

DTC C1249/49 Open in Stop Light Switch Circuit: Description

The document describes a diagnostic trouble code (DTC) related to an open circuit in the stop light switch of a vehicle stability control system. It provides the DTC number, detection conditions, possible trouble areas, inspection procedures to diagnose the issue which include checking fuse integrity, relay resistance, switch resistance, and wire harness connections. The recommended repair is to replace the ABS and traction control actuator assembly if the issue persists after inspections.

Uploaded by

Amil AnAm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

BC–110 BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM

DTC C1249/49 Open in Stop Light Switch Circuit


DESCRIPTION
The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light
switch. The skid control ECU incorporates an open circuit detection circuit. This DTC is set under either of
the following conditions:
• An open is detected in the stop light signal input line when the stop light switch is off.
• An open is detected in the stop light circuit lead to the ground when the stop light switch is off.
DTC No. DTC Detection Condition Trouble Area
C1249/49 When either condition below is met: • ECU-IG1 fuse
1. When IG1 terminal voltage 9.5 to 17.2 V, open • STOP fuse
circuit of stop light switch continues for 0.3 seconds • BRK relay
more. • Stop light switch
2. w/ 16-inch disc: • Stop light switch circuit
With brake pedal load sensing switch ON, master • ABS and TRACTION actuator
pressure 2 MPa or more, vehicle deceleration 0.2 G
or more (calculated based on vehicle speed), stop
switch OFF condition continues for 2 seconds or
more.

WIRING DIAGRAM
BC
Skid Control ECU
ECU-IG1
to IG1 Relay

STP2
BRK

Stop Light Switch STP0

STP1

to Rear Combination Light (LH)

to Rear Combination Light (RH)


STOP
to High Mount Stop Light

ALT

C135995E01
BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM BC–111

INSPECTION PROCEDURE

1 READ VALUE OF INTELLIGENT TESTER (STOP LIGHT SWITCH)

(a) Check the DATA LIST for proper functioning of the stop
light switch.
Skid control ECU
Item (Display) Measurement Item / Range Normal Conditions Diagnostic Note
(Display)
STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed -
OFF: Brake pedal released

OK:
ON (brake pedal is depressed) appears on the
screen.
NG Go to step 3

OK

2 CHECK WIRE HARNESS (STP VOLTAGE)


BC
(a) Disconnect the A19 ECU connector.
Wire Harness Side (b) Measure the voltage of the wire harness side connector.
Standard voltage
Tester Connection Switch Condition Specified Condition
A19 A19-21 (STP2) - Body Brake pedal depressed 8 to 14 V
ground
A19-21 (STP2) - Body Brake pedal released Below 4.0 V
ground

NG Go to step 6

STP2

C121700E42

OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

3 INSPECT FUSE (STOP, ECU-IG1)

(a) Remove the STOP fuse and ECU-IG1 fuse from the
instrument panel junction block.
(b) Measure the resistance of the fuse.
Standard resistance:
Below 1 Ω
NG REPLACE FUSE
BC–112 BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM

OK

4 INSPECT STOP LIGHT CONTROL RELAY (Marking: BRK)

(a) Remove the stop light control relay from the engine room
1 4 2 No. 1 relay block.
4 (b) Measure the resistance of the relay.

3 5 Tester Connection Specified Condition


5
3-4 Below 1 Ω
1 2 3-5 10 kΩ or higher
3
3-4 10 kΩ or higher
(when battery voltage is applied to
A087121E01 terminals 1 and 2)
3-5 Below 1 Ω
(when battery voltage is applied to
terminals 1 and 2)

NG REPLACE STOP LIGHT CONTROL RELAY

OK
BC
5 INSPECT STOP LIGHT SWITCH ASSEMBLY

(a) Disconnect the stop light switch connector.


(b) Measure the resistance of the switch.
Standard resistance
Tester Connection Switch Condition Specified Condition
Pin 1-2 Pin not pushed Below 1 Ω
1-2 Pin pushed 10 kΩ or higher
3-4 Pin not pushed 10 kΩ or higher
3-4 Pin pushed Below 1 Ω
Not Pushed Pushed
NG REPLACE STOP LIGHT SWITCH ASSEMBLY
2 1

4 3
C108891E01

OK
BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM BC–113

6 CHECK WIRE HARNESS (SKID CONTROL ECU - STOP LIGHT SWITCH)

(a) Disconnect the A19 ECU connector.


Wire Harness Side (b) Disconnect the A3 switch connector.
(c) Measure the resistance of the wire harness side
Skid Control ECU
connectors.
A19 Standard resistance
Tester Connection Specified Condition
A19-21 (STP2) - A3-1 Below 1 Ω

NG REPAIR OR REPLACE HARNESS AND


CONNECTOR
STP2

Stop Light Switch Assembly

A3  
 
BC
C121702E05

OK

7 RECONFIRM DTC

(a) Clear the DTC (see page BC-47).


(b) Check if the same DTC is output (see page BC-47).
Result
Result Proceed to
DTC is output A
DTC is not output B

B END

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

You might also like