8/4/2019 AISC Steel Connection Design http://asp.civilbay.

com/connect Moment Connection OMF MC-2

Result Summary - Overall Moment Connection - Beam to Column Code=AISC 360-16 LRFD

Result Summary - Overall geometries & weld limitations = PASS limit states max ratio = 1.37 FAIL

Right Beam to Column geometries & weld limitations = PASS limit states max ratio = 1.37 FAIL

Sketch Moment Connection - Beam to Column Code=AISC 360-16 LRFD

1/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

2/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Beam Flange Force Calc

Beam Flange Force - Right Side Beam

Beam section d b = 17.900 [in] t fb = 0.525 [in]

Flange force moment arm d m = d b - t fb = 17.375 [in]

User input load axial P bR = 0.0 [kips] moment M R = 50.00 [kip-ft]

Beam flange force - top P f-TR = P bR / 2 + M R / d m = 34.5 [kips]

Beam flange force - bottom P f-BR = P bR / 2 - M R / d m = -34.5 [kips]

Panel Zone Shear Force Calc

Column story shear V s = from user input = 0.0 [kips]

Panel zone shear force V p = P f-TR - P f-TL - V s = 34.5 [kips]

Seismic Moment and Beam Flange Force Calc

Seismic OMF Force Calc - Right Side Beam

Refer to AISC 341-16 E1.6b (b), OMF connection design should be based on the maximum moment that
can be transferred to the connection by the system, including the effects of material overstrength and AISC 341-16 E1.6b (b)
strain hardening.
The flexural strength that can be transferred is based on the smaller of the expected flexural strength of
the beam or column, including a 1.1 factor for strain hardening, or the flexural strength resulting from
panel zone shear.

Beam Expected Flexural Strength

Beam sect W18X40 d b = 17.900 [in] Z bx = 78.40 [in 3]

F by = 50.0 [ksi] R by = 1.1

Beam expected flexural strength M be = 1.1 R by F by Z bx = 395.27 [kip-ft]

Column Expected Flexural Strength

Column sect W12X35 Z cx = 51.20 [in 3] F cy = 50.0 [ksi]

R cy = 1.1

Column expected flexural strength M ce = 1.1 R cy F cy Z cx = 258.13 [kip-ft]

Flexural Strength by Panel Zone Shear

Depth of beam db = db = 17.900 [in]

Column sect W12X35 d c = 12.500 [in] b cf = 6.560 [in]

t cw = 0.300 [in] t cf = 0.520 [in]

F cy = 50.0 [ksi] R cy = 1.1

Column sect W12X35 A c = 10.300 [in 2] F cy = 50.0 [ksi]

Column axial yield strength P y = F cy A c = 515.0 [kips] AISC 15 th J10.6 (b)

LRFD-ASD force adjustment factor α = for LRFD = 1.0 AISC 15 th J10.6 (b)

Column axial compression P r = from user input = 15.4 [kips]

when αP r ≤ 0.75 P y , use Eq J10-11 AISC 15 th Eq J10-11

2
3 b cf t cf
th
Column panel zone capacity V pz = 0.6(1.1)R cy F cy d c t cw (1 + ) = 146.9 [kips] AISC 15 Eq J10-11
d b d c t cw

Column panel zone capacity-LRFD V ue = V pz / α s = 1.0 = 146.9 [kips]

Beam sect W18X40 d b = 17.900 [in] t bf = 0.525 [in]

Flexural strength by panel zone

M ue = V ue ( d b - t bf ) = 212.72 [kip-ft]
shear

Min expected flexural strength M ne = min( M be , M ce , M ue ) = 212.72 [kip-ft]

3/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Calculate Story Shear

Assume column inflection point is at the mid height of story above and below beam

Column story height above/below

h t = 0.0 [in] h b = 204.0 [in]
beam

M ne
Story shear V uc = = 12.5 [kips]
hb

Flexural strength after considering

M u = ( V ue + V uc ) ( d b - t bf ) = 230.84 [kip-ft]
story shear

Calculate Shear Load

Beam clear span L cf = from user input = 347 [in]

Shear from max expected flexural
V ne = 2 M u / L cf = 15.9 [kips]
strength
Shear from load combination
V = from user input = 23.5 [kips]
including amplified seismic load

Max shear used in design V u = max( V ne , V ) = 23.5 [kips]

Calculate Flange Force

Beam sect W18X40 d b = 17.900 [in] t bf = 0.525 [in]

Moment arm between flanges d m = d b - t bf = 17.375 [in]

Flange force F fu = M u / d m = 159.4 [kips]

Right Beam to Column MC Connection Code=AISC 360-16 LRFD

Result Summary geometries & weld limitations = PASS limit states max ratio = 1.37 FAIL

Geometry Restriction Checks PASS

Min Bolt Edge Distance - Column Flange

Bolt diameter db = = 0.750 [in]

th
Min edge distance allowed L e-min = = 1.000 [in] AISC 15 Table J3.4

Min edge distance in Column Flange Le = = 1.280 [in]

≥ L e-min OK

Min Bolt Spacing - End Plate

Bolt diameter db = = 0.750 [in]

Min bolt spacing allowed L s-min = 2.667 d b = 2.000 [in] AISC 15 th J3.3

Min Bolt spacing in End Plate Ls = = 3.000 [in]

≥ L s-min OK

Min Bolt Edge Distance - End Plate

Bolt diameter db = = 0.750 [in]

Min edge distance allowed L e-min = = 1.000 [in] AISC 15 th Table J3.4

Min edge distance in End Plate Le = = 1.250 [in]

≥ L e-min OK

Max Bolt Edge Distance - End Plate

Connecting plate thickness tp = = 0.625 [in]

Max edge distance allowed L e-max = min ( 12t , 6" ) = 6.000 [in] AISC 15 th J3.5

Max edge distance in End Plate Le = = 1.500 [in]

≤ L e-max OK

4/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Beam Flange Fillet Weld Limitation PASS

Min Fillet Weld Size

Thinner part joined thickness t= = 0.525 [in]

Min fillet weld size allowed w min = = 0.250 [in] AISC 15 th Table J2.4

Fillet weld size provided w= = 0.438 [in]

≥ w min OK

Min Fillet Weld Length

Fillet weld size provided w= = 0.438 [in]

th
Min fillet weld length allowed L min = 4 x w = 1.750 [in] AISC 15 J2.2b

Min fillet weld length L = 0.5 b fb - k 1b = 2.197 [in]

≥ L min OK

Beam Web Fillet Weld Limitation PASS

Min Fillet Weld Size

Thinner part joined thickness t= = 0.315 [in]

Min fillet weld size allowed w min = = 0.188 [in] AISC 15 th Table J2.4

Fillet weld size provided w= = 0.250 [in]

≥ w min OK

Min Fillet Weld Length

Fillet weld size provided w= = 0.250 [in]

Min fillet weld length allowed L min = 4 x w = 1.000 [in] AISC 15 th J2.2b

Min fillet weld length L = 0.5 d b - k b = 7.762 [in]

≥ L min OK

Min Beam Web to End Plate Fillet Weld Size

Beam web to end-plate fillet weld in the tension-bolt region to develop the yield strength of the beam web AISC DG4 Page 9 Item 7

Shear resistance factor-LRFD φ v = 0.90 AISC 15 th G1

Fillet weld shear strength φ R n-w = = 1.392 [kip/in] AISC 15 th Eq 8-2a

Fillet weld strength φ R n-w x 1.5 x 2 to account for 90° load angle when it's in tension and double fillet
Min double fillet weld size to match
D min = φ v F yb t wb / ( φ R n-w x 1.5 x 2 ) = 3.394 [1/16 "]
beam web yield strength
Fillet weld size provided D= = 4.000 [1/16 "]

≥ D min OK

Verify AISC DG4 Bolt No Prying Assumption AISC DG4 Is Used

Bolt Moment Strength (No Prying)

bolt grade = A325-N F t = 90.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Bolt norminal tensile strength Pt = Ft Ab = 39.8 [kips] AISC 15 th Eq J3-1

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

Bolt moment strength (no prying) M nb = 2 P t ( h 1 + h 2 + h 3 + h 4 ) = 460.56 [kip-ft] AISC DG4 Table 3.3
th
Bolt resistance factor-LRFD φ = 0.75 AISC 15 Eq J3-1

φ M nb = = 345.42 [kip-ft]

End Plate Bending Strength

5/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

End plate width b plate = 7.000 [in] thickness t p = 0.625 [in]

Beam flange width b fb = 6.020 [in]

Effective end plate width b p = min ( b plate , b fb + 1" ) = 7.000 [in] AISC DG4 Page 9 item 5

End plate yield strength F yp = 36.0 [ksi]

See AISC DG4 Table 3.3 for all formulas to derive the following parameters AISC DG4 Table 3.3

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

g = 4.000 [in] d e = 1.250 [in]

p fi = 2.000 [in] p fo = 2.000 [in]

p b = 3.000 [in]

s = 2.646 [in] Y p = 231.83 [in]

Flexure resistance factor-LRFD φ b = 0.90 AISC 15 th F1 (1)

End plate bending strength φ b M pl = φ b F yp t 2p Yp = 244.50 [kip-ft] AISC DG4 Table 3.1

Max Moment in Demand

Moment by bolt strength-no prying φ b M nb = from above calc = 345.42 [kip-ft]

Moment by user input M r = from user input = 50.00 [kip-ft]

Moment in demand φ M np = min ( φ b M nb , M r ) = 50.00 [kip-ft]

Check Thick End Plate Condition

Check thick end plate condition φ b M pl >= 1.11 X φ M np AISC DG4 Eq 3.33

ratio = 0.23 thick plate

Column Flange Bending Strength

See AISC DG4 Table 3.5 for all formulas to derive the following parameters AISC DG4 Table 3.5

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

*** Stiffened Column Flange Case ***

Column section b fc = 6.560 [in] t fc = 0.520 [in]

F yc = 50.0 [ksi] bolt gage g = 4.000 [in]

s = 2.561 [in] c = 4.525 [in]

Stiffener plate thickness t s = 0.500 [in]

p si = 2.013 [in] p so = 2.013 [in]

p b = 3.000 [in] d e = 1.250 [in]

Y c = 239.0 [in]

Flexure resistance factor-LRFD φ b = 0.90 AISC 15 th F1 (1)

Column flange bending strength φ b M cf = φ b F yc t 2fc Y c = 242.33 [kip-ft] AISC DG4 Table 3.5

Check Thick Column Flange Condition

Check thick column flange condition φ b M cf >= 1.11 X φ M np AISC DG4 Eq 3.35

ratio = 0.23 thick plate

The thick end plate and column flange conditions are met. AISG DG4 is used and
AISC DG4 Eq 3.33 & 3.35
no bolt prying is considered

6/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Bolt Moment Strength (No Prying) ratio = 34.5 / 238.6 = 0.14 PASS

bolt grade = A325-N F t = 90.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Bolt norminal tensile strength Pt = Ft Ab = 39.8 [kips] AISC 15 th Eq J3-1

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force required in tension P uf_t = P u / 2 - M u / d m = 34.5 [kips]

Flange force resistance by bolt Fn = 2 Pt ( h1 + h2 + h3 + h4 ) / dm = 318.1 [kips] AISC DG4 Eq 3.8

th
Bolt resistance factor-LRFD φ = 0.75 AISC 15 Eq J3-1

φ Fn = = 238.6 [kips] AISC DG4 Eq 3.7

ratio = 0.14 > P uf_t OK

Bolt Shear Strength ratio = 12.3 / 143.1 = 0.09 PASS

th
Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 Table J3.2
2
bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in ]

Number of bolt carried shear n s = 8.0 shear plane m = 1

Bolt group eccentricity coefficient C ec = = 1.000

Required shear strength Vu = = 12.3 [kips]

th
Bolt shear strength R n = F nv A b n s m C ec = 190.9 [kips] AISC 15 Eq J3-1
th
Bolt resistance factor-LRFD φ = 0.75 AISC 15 Eq J3-1

φ Rn = = 143.1 [kips]

ratio = 0.09 > Vu OK

7/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Bolt Bearing/TearOut Strength on End Plate ratio = 12.3 / 143.1 = 0.09 PASS

Single Bolt Shear Strength

Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Single bolt shear strength R n-bolt = F nv A b = 23.9 [kips] AISC 15 th Eq J3-1

Bolt Bearing/TearOut Strength on Plate

3 13 th
Bolt hole diameter bolt dia d b = ⁄ 4 [in] bolt hole dia d h = ⁄ 16 [in] AISC 15 Table J3.3

Bolt spacing & edge distance spacing L s = 3.000 [in] edge distance L e = 1.250 [in]

Plate tensile strength F u = 58.0 [ksi]

Plate thickness t = 0.625 [in]

Interior Bolt

Bolt hole edge clear distance Lc = Ls - dh = 2.188 [in]

Bolt tear out/bearing strength R n-t&b-in = 1.2 L c t F u ≤ 2.4 d b t F u AISC 15 th Eq J3-6a

= 95.2 ≤ 65.3 = 65.3 [kips]

Bolt strength at interior R n-in = min ( R n-t&b-in , R n-bolt ) = 23.9 [kips]

Edge Bolt

Bolt hole edge clear distance Lc = Le - dh / 2 = 0.844 [in]

Bolt tear out/bearing strength R n-t&b-ed = 1.2 L c t F u ≤ 2.4 d b t F u AISC 15 th Eq J3-6a

= 36.7 ≤ 65.3 = 36.7 [kips]

Bolt strength at edge R n-ed = min ( R n-t&b-ed , R n-bolt ) = 23.9 [kips]

Number of bolt interior n in = 6 edge n ed = 2

Bolt bearing strength for all bolts R n = n in R n-in + n ed R n-ed = 190.9 [kips]

Required shear strength Vu = = 12.3 [kips]

Bolt resistance factor-LRFD φ = 0.75 AISC 15 th J3-10

φ Rn = = 143.1 [kips]

ratio = 0.09 > Vu OK

8/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Bolt Bearing/TearOut Strength on Column Flange ratio = 12.3 / 143.1 = 0.09 PASS

Single Bolt Shear Strength

Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Single bolt shear strength R n-bolt = F nv A b = 23.9 [kips] AISC 15 th Eq J3-1

Bolt Bearing/TearOut Strength on Plate

3 13 th
Bolt hole diameter bolt dia d b = ⁄ 4 [in] bolt hole dia d h = ⁄ 16 [in] AISC 15 Table J3.3

Bolt spacing spacing L s = 3.000 [in]

Plate tensile strength F u = 65.0 [ksi]

Plate thickness t = 0.520 [in]

Interior Bolt

Bolt hole edge clear distance Lc = Ls - dh = 2.188 [in]

Bolt tear out/bearing strength R n-t&b-in = 1.2 L c t F u ≤ 2.4 d b t m F u AISC 15 th Eq J3-6a

= 88.7 ≤ 60.8 = 60.8 [kips]

Bolt strength at interior R n-in = min ( R n-t&b-in , R n-bolt ) = 23.9 [kips]

Number of bolt interior n in = 8

Bolt bearing strength for all bolts R n = n in R n-in = 190.9 [kips]

Required shear strength Vu = = 12.3 [kips]

Bolt resistance factor-LRFD φ = 0.75 AISC 15 th J3-10

φ Rn = = 143.1 [kips]

ratio = 0.09 > Vu OK

End Plate Flexural Yielding ratio = 34.5 / 168.9 = 0.20 PASS

End Plate Bending Strength

End plate width b plate = 7.000 [in] thickness t p = 0.625 [in]

Beam flange width b fb = 6.020 [in]

Effective end plate width b p = min ( b plate , b fb + 1" ) = 7.000 [in] AISC DG4 Page 9 item 5

End plate yield strength F yp = 36.0 [ksi]

See AISC DG4 Table 3.3 for all formulas to derive the following parameters AISC DG4 Table 3.3

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

g = 4.000 [in] d e = 1.250 [in]

p fi = 2.000 [in] p fo = 2.000 [in]

p b = 3.000 [in]

s = 2.646 [in] Y p = 231.83 [in]

th
Flexure resistance factor-LRFD φ b = 0.90 AISC 15 F1 (1)

End plate bending strength φ b M pl = φ b F yp t 2p Yp = 244.50 [kip-ft] AISC DG4 Table 3.1

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force required in tension P uf_t = P u / 2 - M u / d m = 34.5 [kips]

Flange force provided by end plate

φ R pl = φ M pl / d m = 168.9 [kips] AISC DG4 Eq 3.10
bending

ratio = 0.20 > P uf_t OK

9/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

End Plate Stiffener Geometry Limitations PASS

Beam web thick t wb = 0.315 [in] Stiff thick t s = 0.438 [in]

Beam yield strength F yb = 50.0 [ksi] Stiff yield F ys = 36.0 [ksi]

Min Stiffener Plate Thickness

Min stiffener plate thickness t smin = t wb F yb / F ys = 0.438 [in] AISC DG4 Eq 3.15

Stiffener plate thickness ts = = 0.438 [in]

≥ t smin OK

Min Stiff Thick to Avoid Local Buckiling

Stiffener plate height h st = 6.250 [in] E = 29000 [ksi]

Stiffener plate strength F ys = 36.0 [ksi]

Min stiffener plate thickness t smin = 1.79 h st √ F ys / E = 0.394 [in] AISC DG4 Eq 3.16

Stiffener plate thickness ts = = 0.438 [in]

≥ t smin OK

Beam Flange Weld Strength ratio = 34.5 / 133.3 = 0.26 PASS

Flange force required in tension P uf_t = P u / 2 - M u / d m = 34.5 [kips]

Fillet weld length - double fillet L = [b fb + ( b fb - 2k 1b )] /2 as dbl fillet = 5.207 [in]

Fillet Weld Strength Check

Fillet weld leg size w = 7⁄ 16 [in] load angle θ = 90.0 [°]

Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 th Table 8-3

Number of weld line n=2 for double fillet

Load angle coefficient C 2 = ( 1 + 0.5 sin 1.5 θ ) = 1.50 AISC 15 th Page 8-9

Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 38.973 [kip/in] AISC 15 th Eq 8-1

Base metal - beam flange thickness t = 0.525 [in] tensile F u = 65.0 [ksi]
th
Base metal - beam flange is in tension, tensile rupture as per AISC 15 Eq J4-2 is checked AISC 15 th J2.4

Base metal tensile rupture R n-b = F u t = 34.125 [kip/in] AISC 15 th Eq J4-2

Double fillet linear shear strength R n = min ( R n-w , R n-b ) = 34.125 [kip/in] AISC 15 th Eq 9-2

Resistance factor-LRFD φ = 0.75 AISC 15 th Eq 8-1

φ Rn = = 25.594 [kip/in]

Shear resistance required P uf_t = = 34.5 [kips]

Fillet weld length - double fillet L= = 5.207 [in]

Shear resistance provided φ Fn = φ Rn x L = 133.3 [kips]

ratio = 0.26 > P uf_t OK

10/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Beam Web Weld Strength ratio = 12.3 / 71.5 = 0.17 PASS

Beam Web Effective Weld Length Calc

Beam section d b = 17.900 [in] t fb = 0.525 [in]

k b = 1.188 [in]

Bolt diameter d bolt = 0.750 [in] bolt inner pitch p fi = 2.000 [in]

Effective weld length case 1 L 1 = 0.5 d b - k b = 7.762 [in] AISC DG4 Page 38

Effective weld length case 2 L 2 = d b - 2t fb - p fi - 2 d bolt = 13.350 [in] AISC DG4 Page 38

Fillet weld length - double fillet L = min( L 1 , L 2 ) = 7.762 [in]

Fillet Weld Strength Check

1
Fillet weld leg size w = ⁄4 [in] load angle θ = 0.0 [°]
th
Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 Table 8-3

Number of weld line n=2 for double fillet

1.5 th
Load angle coefficient C 2 = ( 1 + 0.5 sin θ) = 1.00 AISC 15 Page 8-9
th
Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 14.847 [kip/in] AISC 15 Eq 8-1

Base metal - beam web thickness t = 0.315 [in] tensile F u = 65.0 [ksi]
th
Base metal - beam web is in shear, shear rupture as per AISC 15 Eq J4-4 is checked AISC 15 th J2.4

Base metal shear rupture R n-b = 0.6 F u t = 12.285 [kip/in] AISC 15 th Eq J4-4

Double fillet linear shear strength R n = min ( R n-w , R n-b ) = 12.285 [kip/in] AISC 15 th Eq 9-2

Resistance factor-LRFD φ = 0.75 AISC 15 th Eq 8-1

φ Rn = = 9.214 [kip/in]

Shear resistance required Vu = = 12.3 [kips]

Fillet weld length - double fillet L= = 7.762 [in]

Shear resistance provided φ Fn = φ Rn x L = 71.5 [kips]

ratio = 0.17 > Vu OK

11/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Column Flexural Yielding ratio = 34.5 / 167.4 = 0.21 PASS

Column Flange Bending Strength

See AISC DG4 Table 3.5 for all formulas to derive the following parameters AISC DG4 Table 3.5

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

*** Stiffened Column Flange Case ***

Column section b fc = 6.560 [in] t fc = 0.520 [in]

F yc = 50.0 [ksi] bolt gage g = 4.000 [in]

s = 2.561 [in] c = 4.525 [in]

Stiffener plate thickness t s = 0.500 [in]

p si = 2.013 [in] p so = 2.013 [in]

p b = 3.000 [in] d e = 1.250 [in]

Y c = 239.0 [in]

Flexure resistance factor-LRFD φ b = 0.90 AISC 15 th F1 (1)

Column flange bending strength φ b M cf = φ b F yc t 2fc Y c = 242.33 [kip-ft] AISC DG4 Table 3.5

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force required in tension P uf_t = P u / 2 - M u / d m = 34.5 [kips]

Flange force provided by column

φ R cf = φ M cf / d m = 167.4 [kips] AISC DG4 Eq 3.21
flange bending

ratio = 0.21 > P uf_t OK

Column Web Yielding ratio = 34.5 / 113.6 = 0.30 PASS

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force in demand P uf = max ( P uf_t , P uf_c ) = 34.5 [kips] AISC DG13 Eq 4.2-1

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

Column yield strength F yc = 50.0 [ksi]

Distance from to top of column to
d end = 13.000 [in]
top of beam flange
Top column reduction factor C t = 1.0 AISC DG4 Eq 3.24

Beam flange fillet weld size w = 0.438 [in] beam flange t fb = 0.525 [in]

Length of bearing N = t fb + 2 w = 1.400 [in] AISC DG4 Eq 3.24

End plate thickness t p = 0.625 [in]

Column web yielding strength R n = C t ( 6 k c + N + 2 t p ) F yc t wc = 113.6 [kips] AISC DG4 Eq 3.24

Resistance factor-LRFD φ = 1.00 AISC 15 th J10.2

φ Rn = = 113.6 [kips]

ratio = 0.30 > P uf OK

12/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Column Web Buckling ratio = 34.5 / 64.7 = 0.53 PASS

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force required in
P uf_c = P u / 2 - M u / d m = 34.5 [kips]
compression

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

h = dc - 2 kc = 10.860 [in]

Column yield strength F yc = 50.0 [ksi] E c = 29000 [ksi]

Distance from top of beam flange to

d end-flg = 13.000 [in] beam flange t fb = 0.525 [in]
top of column

Distance from center of flange force

d end-F = d end-flg + 0.5 t fb = 13.263 [in]
to top of column
d end-F ≥ d c /2 , R n has no reduction AISC 15 th J10.5

Top column reduction factor C t = 1.0 AISC 15 th J10.5

Column web buckling strength Rn =

C t 24 t 3wc √ E c F yc = 71.9 [kips] AISC 15 th Eq J10-8
h

Resistance factor-LRFD φ = 0.90 AISC 15 th J10.5

φ Rn = = 64.7 [kips]

ratio = 0.53 > P uf_c OK

Column Web Crippling ratio = 34.5 / 109.5 = 0.32 PASS

Flange force moment arm d m = d b - t fb = 17.375 [in]

Flange force required in
P uf_c = P u / 2 - M u / d m = 34.5 [kips]
compression

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

Column yield strength F yc = 50.0 [ksi] E c = 29000 [ksi]

Beam flange fillet weld size w = 0.438 [in] beam flange t fb = 0.525 [in]

End plate thickness t p = 0.625 [in]

Length of bearing l b = t fb + 2 w + 2 t p = 2.650 [in]

Distance from top of column to top

d end-flg = = 13.000 [in]
of beam flange
Distance from top of column to
d end-F = d end-flg + 0.5 t fb = 13.263 [in]
center of flange force

d end-F ≥ d c /2 , use Eq J10-4 AISC 15 th Eq J10-4

lb t wc
2
Column web crippling strength R n = 0.8 t wc [1+3 ( ) 1.5]x = 146.0 [kips] AISC 15 th Eq J10-4
dc t fc

E c F yc t fc 0.5
( )
t wc
Resistance factor-LRFD φ = 0.75 AISC 15 th J10.3

φ Rn = = 109.5 [kips]

ratio = 0.32 > P uf_c OK

13/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Column Panel Zone Shear ratio = 34.5 / 109.3 = 0.32 PASS

Panel zone shear force V p = P f-TR - P f-TL - V s = 34.5 [kips]

Column W12X35 d c = 12.500 [in] b cf = 6.560 [in]

t cf = 0.520 [in] t cw = 0.300 [in]

A c = 10.300 [in 2] F cy = 50.0 [ksi]

Beam W18X40 d b = 17.900 [in] t bf = 0.525 [in]

Beam flange thickness t bf = = 0.525 [in]

Moment arm between flanges d m = d - t bf = 17.900 [in]

Column axial compression P r = from user input = 15.4 [kips]

Column axial yield strength P y = F cy A c = 515.0 [kips] AISC 15 th J10.6 (b)

LRFD-ASD force adjustment factor α = for LRFD = 1.0 AISC 341-16 D1.2a (b)

when αP r ≤ 0.75 P y , use Eq J10-11 AISC 15 th Eq J10-11

3 b cf t 2cf
Column web panel zone capacity R n = 0.6 F cy d c t cw (1 + ) = 121.4 [kips] AISC 15 th Eq J10-11
d m d c t cw

Resistance factor-LRFD φ = 0.90 AISC 15 th J10.6

φ Rn = = 109.3 [kips]

ratio = 0.32 > Vp OK

14/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Material & Geometry Limitations PASS

Check Max Beam Yield Stress

Condition : beam max material F y ≤ F y_max = 55 ksi AISC 341-16 A3.1

Beam yield strength F yb = 50.0 [ksi]

≤ F y_max OK

Check Max Column Yield Stress

Condition : column max material F y ≤ F y_max = 55 ksi AISC 341-16 A3.1

Column yield strength F yc = 50.0 [ksi]

≤ F y_max OK

Check Max Gage

Condition : max bolt gage is limited to beam b f AISC 358-16 6.9.1

Beam flange width b f = 6.020 [in] gage = 4.000 [in]

≤ bf OK

Check Min Pitch

Condition : min bolt pitch distance p ≥ d b +0.50 in AISC 358-16 6.9.2

Bolt pitch p fi = 2.000 [in] p fo = 2.000 [in]

Bolt dia d b = 0.750 [in]

Min bolt pitch distance allowed p min = d b +0.50 in = 1.250 [in]

Min bolt pitch distance p = min( p fi , p fo ) = 2.000 [in]

≥ p min OK

Check Min Inner Bolt Pitch P b

Condition : min inner bolt pitch p b ≥ 8/3 x bolt dia AISC 358-16 6.9.2

Bolt dia d b = 0.750 [in]

Min inner bolt pitch allowed p bmin = 8/3 x d b = 2.000 [in]

Inner bolt pitch pb = = 3.000 [in]

≥ p bmin OK

Seismic Bolt Limitation PASS

Check Bolt Grade Material

Condition : Bolt grade must be A325 or A490

Bolt grade = A325-N

OK AISC 358-16 4.1

Check Bolt Hole Type

Condition : Bolt hole type shall be STD or SSLT

Bolt hole type = PL1=STD PL2=STD

OK AISC 341-16 D2.2 (3)

Seismic End Plate Width Limitation PASS

Check End Plate Width

Condition : end palte width b p ≥ beam flange width b f

Beam flange width bf = = 6.020 [in]

End plate width bp = = 7.000 [in]

≥ bf OK AISC 358-16 6.9.3

15/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Column Beam Moment Ratio N/A

The column beam moment ratio requirement applys to SMF connection only. AISC 341-16 E3.4a
It's OMF connection, so the column beam moment ratio check is not required.

Seismic Check Thick Plate to Meet AISC 358-10 6.10 Assumption PASS

The seismic design of extended end plate moment connection is based on the Design Procedure stated in
AISC 358-10 6.10
Refer to AISC 358-10 6.10 commentary on page 9.2-139. The Design Procedure is very similar to that in
AISC Design Guide 4 (Murray and Sumner, 2003) except that different resistance factors are used. AISC 358-16 6.10
AISC Design Guide 4 is based on the thick plate assumption and the bolt has no prying action.
For this reason the thick plate assumption is checked here and it will flag FAIL if the thick plate condition
is not met. If FAIL user can increase the end plate thickness to get this check pass.

Bolt Moment Strength (No Prying)

th
bolt grade = A325-N F t = 90.0 [ksi] AISC 15 Table J3.2
2
bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in ]
th
Bolt norminal tensile strength Pt = Ft Ab = 39.8 [kips] AISC 15 Eq J3-1

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

Bolt moment strength (no prying) M nb = 2 P t ( h 1 + h 2 + h 3 + h 4 ) = 460.56 [kip-ft] AISC DG4 Table 3.3

Bolt resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φ n M nb = = 414.51 [kip-ft]

End Plate Bending Strength

End plate width b plate = 7.000 [in] thickness t p = 0.625 [in]

Beam flange width b fb = 6.020 [in]

Effective end plate width b p = min ( b plate , b fb + 1" ) = 7.000 [in] AISC DG4 Page 9 item 5

End plate yield strength F yp = 36.0 [ksi]

See AISC DG4 Table 3.3 for all formulas to derive the following parameters AISC DG4 Table 3.3

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

g = 4.000 [in] d e = 1.250 [in]

p fi = 2.000 [in] p fo = 2.000 [in]

p b = 3.000 [in]

s = 2.646 [in] Y p = 231.83 [in]

Flexure resistance factor-LRFD φ d = 1.00 AISC 358-16 2.4.1

End plate bending strength φ d M pl = φ d F yp t 2p Yp = 271.67 [kip-ft] AISC DG4 Table 3.1

Max Moment in Demand

Moment by bolt strength-no prying φ d M nb = from above calc = 414.51 [kip-ft]

Moment by user input M r = from user input = 50.00 [kip-ft]

Moment in demand φ M np = min ( φ d M nb , M r ) = 50.00 [kip-ft]

Check Thick End Plate Condition

Check thick end plate condition φ d M pl >= 1.11 X φ M np AISC DG4 Eq 3.33

ratio = 0.20 thick plate

Column Flange Bending Strength

16/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2
g g g

See AISC DG4 Table 3.5 for all formulas to derive the following parameters AISC DG4 Table 3.5

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

*** Stiffened Column Flange Case ***

Column section b fc = 6.560 [in] t fc = 0.520 [in]

F yc = 50.0 [ksi] bolt gage g = 4.000 [in]

s = 2.561 [in] c = 4.525 [in]

Stiffener plate thickness t s = 0.500 [in]

p si = 2.013 [in] p so = 2.013 [in]

p b = 3.000 [in] d e = 1.250 [in]

Y c = 239.0 [in]

Flexure resistance factor-LRFD φ d = 1.00 AISC 358-16 2.4.1

Column flange bending strength φ d M cf = φ d F yc t 2fc Yc = 269.25 [kip-ft] AISC DG4 Table 3.5

Check Thick Column Flange Condition

Check thick column flange condition φ d M cf >= 1.11 X φ M np AISC DG4 Eq 3.35

ratio = 0.21 thick plate

The thick end plate and column flange conditions are met. AISG DG4 is used and
AISC DG4 Eq 3.33 & 3.35
no bolt prying is considered

Seismic Bolt Moment Strength (No Prying) ratio = 159.4 / 286.3 = 0.56 PASS

bolt grade = A325-N F t = 90.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Bolt norminal tensile strength Pt = Ft Ab = 39.8 [kips] AISC 15 th Eq J3-1

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

Flange force moment arm d m = d b - t fb = 17.375 [in]

Seismic flange force P uf_t = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Flange force resistance by bolt Fn = 2 Pt ( h1 + h2 + h3 + h4 ) / dm = 318.1 [kips] AISC DG4 Eq 3.8

Bolt resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φn Fn = = 286.3 [kips] AISC DG4 Eq 3.7

ratio = 0.56 > P uf_t OK

17/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Bolt Shear Strength ratio = 23.5 / 171.8 = 0.14 PASS

Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Number of bolt carried shear n s = 8.0 shear plane m = 1

Bolt group eccentricity coefficient C ec = = 1.000

Required shear strength V u = see Seismic Moment and Beam = 23.5 [kips]
Flange Force Calc

Bolt shear strength R n = F nv A b n s m C ec = 190.9 [kips] AISC 15 th Eq J3-1

Bolt resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φn Rn = = 171.8 [kips]

ratio = 0.14 > Vu OK

Seismic Bolt Bearing/TearOut Strength on End Plate ratio = 23.5 / 171.8 = 0.14 PASS

Single Bolt Shear Strength

Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Single bolt shear strength R n-bolt = F nv A b = 23.9 [kips] AISC 15 th Eq J3-1

Bolt Bearing/TearOut Strength on Plate

3 13 th
Bolt hole diameter bolt dia d b = ⁄ 4 [in] bolt hole dia d h = ⁄ 16 [in] AISC 15 Table J3.3

Bolt spacing & edge distance spacing L s = 3.000 [in] edge distance L e = 1.250 [in]

Plate tensile strength F u = 58.0 [ksi]

Plate thickness t = 0.625 [in]

Interior Bolt

Bolt hole edge clear distance Lc = Ls - dh = 2.188 [in]

Bolt tear out/bearing strength R n-t&b-in = 1.2 L c t F u ≤ 2.4 d b t F u AISC 15 th Eq J3-6a

= 95.2 ≤ 65.3 = 65.3 [kips]

Bolt strength at interior R n-in = min ( R n-t&b-in , R n-bolt ) = 23.9 [kips]

Edge Bolt

Bolt hole edge clear distance Lc = Le - dh / 2 = 0.844 [in]

Bolt tear out/bearing strength R n-t&b-ed = 1.2 L c t F u ≤ 2.4 d b t F u AISC 15 th Eq J3-6a

= 36.7 ≤ 65.3 = 36.7 [kips]

Bolt strength at edge R n-ed = min ( R n-t&b-ed , R n-bolt ) = 23.9 [kips]

Number of bolt interior n in = 6 edge n ed = 2

Bolt bearing strength for all bolts R n = n in R n-in + n ed R n-ed = 190.9 [kips]

Required shear strength V u = see Seismic Moment and Beam = 23.5 [kips]
Flange Force Calc

Bolt resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φn Rn = = 171.8 [kips]

ratio = 0.14 > Vu OK

18/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Bolt Bearing/TearOut Strength on Column Flange ratio = 23.5 / 171.8 = 0.14 PASS

Single Bolt Shear Strength

Bolt shear stress bolt grade = A325-N F nv = 54.0 [ksi] AISC 15 th Table J3.2

bolt dia d b = 0.750 [in] bolt area A b = 0.442 [in 2]

Single bolt shear strength R n-bolt = F nv A b = 23.9 [kips] AISC 15 th Eq J3-1

Bolt Bearing/TearOut Strength on Plate

3 13 th
Bolt hole diameter bolt dia d b = ⁄ 4 [in] bolt hole dia d h = ⁄ 16 [in] AISC 15 Table J3.3

Bolt spacing spacing L s = 3.000 [in]

Plate tensile strength F u = 65.0 [ksi]

Plate thickness t = 0.520 [in]

Interior Bolt

Bolt hole edge clear distance Lc = Ls - dh = 2.188 [in]

Bolt tear out/bearing strength R n-t&b-in = 1.2 L c t F u ≤ 2.4 d b t m F u AISC 15 th Eq J3-6a

= 88.7 ≤ 60.8 = 60.8 [kips]

Bolt strength at interior R n-in = min ( R n-t&b-in , R n-bolt ) = 23.9 [kips]

Number of bolt interior n in = 8

Bolt bearing strength for all bolts R n = n in R n-in = 190.9 [kips]

Required shear strength V u = see Seismic Moment and Beam = 23.5 [kips]
Flange Force Calc

Bolt resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φn Rn = = 171.8 [kips]

ratio = 0.14 > Vu OK

Seismic End Plate Shear ratio = 79.7 / 94.5 = 0.84 PASS

Seismic flange force 0.5F fu = see Seismic Moment and Beam = 79.7 [kips]
Flange Force Calc

End plate width b p = 7.000 [in] thickness t p = 0.625 [in]

F yp = 36.0 [ksi] F up = 58.0 [ksi]

Check End Plate Shear Yielding AISC 358-16 Eq 6.10-7

Plate shear yield strength R ny = 0.6 F yp b p t p = 94.5 [kips] AISC 358-16 Eq 6.10-7

Resistance factor-LRFD φ d = 1.00 AISC 358-16 2.4.1

φ d R ny = = 94.5 [kips]

ratio = 0.84 > 0.5F fu OK

Check End Plate Shear Rupture AISC 358-16 Eq 6.10-8

Bolt hole diameter bolt dia d b = 3⁄ 4 [in] bolt hole dia d h = 7⁄ 8 [in] AISC 15 th B4.3b

Number of bolt n=2

Plate net area in shear A nv = ( b p - n d h ) t p = 3.281 [in 2]

Plate shear rupture strength R nr = 0.6 F up A nv = 114.2 [kips] AISC 358-16 Eq 6.10-8

Resistance factor-LRFD φ n = 0.90 AISC 358-16 2.4.1

φ n R nr = = 102.8 [kips]

ratio = 0.78 > 0.5F fu OK

19/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic End Plate Flexural Yielding ratio = 159.4 / 187.6 = 0.85 PASS

End Plate Bending Strength

End plate width b plate = 7.000 [in] thickness t p = 0.625 [in]

Beam flange width b fb = 6.020 [in]

Effective end plate width b p = min ( b plate , b fb + 1" ) = 7.000 [in] AISC DG4 Page 9 item 5

End plate yield strength F yp = 36.0 [ksi]

See AISC DG4 Table 3.3 for all formulas to derive the following parameters AISC DG4 Table 3.3

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

g = 4.000 [in] d e = 1.250 [in]

p fi = 2.000 [in] p fo = 2.000 [in]

p b = 3.000 [in]

s = 2.646 [in] Y p = 231.83 [in]

Flexure resistance factor-LRFD φ d = 1.00 AISC 358-16 2.4.1

End plate bending strength φ d M pl = φ d F yp t 2p Y p = 271.67 [kip-ft] AISC DG4 Table 3.1

Seismic flange force P uf_t = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Flange force provided by end plate

φ R pl = φ M pl / d m = 187.6 [kips] AISC DG4 Eq 3.10
bending

ratio = 0.85 > P uf_t OK

Seismic End Plate Stiffener Geometry Limitations PASS

Beam web thick t wb = 0.315 [in] Stiff thick t s = 0.438 [in]

Beam yield strength F yb = 50.0 [ksi] Stiff yield F ys = 36.0 [ksi]

Min Stiffener Plate Thickness

Min stiffener plate thickness t smin = t wb F yb / F ys = 0.438 [in] AISC DG4 Eq 3.15

Stiffener plate thickness ts = = 0.438 [in]

≥ t smin OK

Min Stiff Thick to Avoid Local Buckiling

Stiffener plate height h st = 6.250 [in] E = 29000 [ksi]

Stiffener plate strength F ys = 36.0 [ksi]

Min stiffener plate thickness t smin = 1.79 h st √ F ys / E = 0.394 [in] AISC DG4 Eq 3.16

Stiffener plate thickness ts = = 0.438 [in]

≥ t smin OK

20/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Beam Flange Weld Strength ratio = 159.4 / 152.2 = 1.05 FAIL

Flange force required in tension P uf_t = P u / 2 - M u / d m = 159.4 [kips]

Fillet weld length - double fillet L = [b fb + ( b fb - 2k 1b )] /2 as dbl fillet = 5.207 [in]

Fillet Weld Strength Check

Fillet weld leg size w = 7⁄ 16 [in] load angle θ = 90.0 [°]

Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 th Table 8-3

Number of weld line n=2 for double fillet

Load angle coefficient C 2 = ( 1 + 0.5 sin 1.5 θ ) = 1.50 AISC 15 th Page 8-9

Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 38.973 [kip/in] AISC 15 th Eq 8-1

Base metal - beam flange thickness t = 0.525 [in] tensile F u = 65.0 [ksi]
th th
Base metal - beam flange is in tension, tensile rupture as per AISC 15 Eq J4-2 is checked AISC 15 J2.4
th
Base metal tensile rupture R n-b = F u t = 34.125 [kip/in] AISC 15 Eq J4-2

For seismic nonductile limit state, weld strength use φ = 0.75 , base metal rupture use φ n = 0.9
AISC 358-16 2.4.1
Increase base metal rupture strength due to higher φ value when compare to weld strength

0.90
th
Double fillet linear shear strength R n = min ( R n-w , R n-b x ) = 38.973 [kip/in] AISC 15 Eq 9-2
0.75

Resistance factor-LRFD φ = 0.75 AISC 15 th Eq 8-1

φ Rn = = 29.230 [kip/in]

Shear resistance required P uf_t = = 159.4 [kips]

Fillet weld length - double fillet L= = 5.207 [in]

Shear resistance provided φ Fn = φ Rn x L = 152.2 [kips]

ratio = 1.05 < P uf_t NG

21/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Beam Web Weld Strength ratio = 23.5 / 85.8 = 0.27 PASS

Beam Web Effective Weld Length Calc

Beam section d b = 17.900 [in] t fb = 0.525 [in]

k b = 1.188 [in]

Bolt diameter d bolt = 0.750 [in] bolt inner pitch p fi = 2.000 [in]

Effective weld length case 1 L 1 = 0.5 d b - k b = 7.762 [in] AISC DG4 Page 38

Effective weld length case 2 L 2 = d b - 2t fb - p fi - 2 d bolt = 13.350 [in] AISC DG4 Page 38

Fillet weld length - double fillet L = min( L 1 , L 2 ) = 7.762 [in]

Fillet Weld Strength Check

1
Fillet weld leg size w = ⁄4 [in] load angle θ = 0.0 [°]
th
Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 Table 8-3

Number of weld line n=2 for double fillet

1.5 th
Load angle coefficient C 2 = ( 1 + 0.5 sin θ) = 1.00 AISC 15 Page 8-9
th
Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 14.847 [kip/in] AISC 15 Eq 8-1

Base metal - beam web thickness t = 0.315 [in] tensile F u = 65.0 [ksi]
th
Base metal - beam web is in shear, shear rupture as per AISC 15 Eq J4-4 is checked AISC 15 th J2.4

Base metal shear rupture R n-b = 0.6 F u t = 12.285 [kip/in] AISC 15 th Eq J4-4

For seismic nonductile limit state, weld strength use φ = 0.75 , base metal rupture use φ n = 0.9
AISC 358-16 2.4.1
Increase base metal rupture strength due to higher φ value when compare to weld strength

0.90
Double fillet linear shear strength R n = min ( R n-w , R n-b x ) = 14.742 [kip/in] AISC 15 th Eq 9-2
0.75

th
Resistance factor-LRFD φ = 0.75 AISC 15 Eq 8-1

φ Rn = = 11.057 [kip/in]

Shear resistance required Vu = = 23.5 [kips]

Fillet weld length - double fillet L= = 7.762 [in]

Shear resistance provided φ Fn = φ Rn x L = 85.8 [kips]

ratio = 0.27 > Vu OK

22/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Column Flexural Yielding ratio = 159.4 / 186.0 = 0.86 PASS

Column Flange Bending Strength

See AISC DG4 Table 3.5 for all formulas to derive the following parameters AISC DG4 Table 3.5

Tension bolt moment arm h 1 = 22.638 [in] h 2 = 19.638 [in]

h 3 = 15.113 [in] h 4 = 12.113 [in]

*** Stiffened Column Flange Case ***

Column section b fc = 6.560 [in] t fc = 0.520 [in]

F yc = 50.0 [ksi] bolt gage g = 4.000 [in]

s = 2.561 [in] c = 4.525 [in]

Stiffener plate thickness t s = 0.500 [in]

p si = 2.013 [in] p so = 2.013 [in]

p b = 3.000 [in] d e = 1.250 [in]

Y c = 239.0 [in]

Flexure resistance factor-LRFD φ d = 1.00 AISC 358-16 2.4.1

Column flange bending strength φ d M cf = φ d F yc t 2fc Y c = 269.25 [kip-ft] AISC DG4 Table 3.5

Seismic flange force P uf_t = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Flange force provided by column

φ R cf = φ M cf / d m = 186.0 [kips] AISC DG4 Eq 3.21
flange bending

ratio = 0.86 > P uf_t OK

Seismic Column Web Yielding 159.4 / 113.6 N/A

Flange force moment arm d m = d b - t fb = 17.375 [in]

Seismic flange force P uf_c = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

Column yield strength F yc = 50.0 [ksi]

Distance from to top of column to
d end = 13.000 [in]
top of beam flange
Top column reduction factor C t = 1.0 AISC DG4 Eq 3.24

Beam flange fillet weld size w = 0.438 [in] beam flange t fb = 0.525 [in]

Length of bearing N = t fb + 2 w = 1.400 [in] AISC DG4 Eq 3.24

End plate thickness t p = 0.625 [in]

Column web yielding strength R n = C t ( 6 k c + N + 2 t p ) F yc t wc = 113.6 [kips] AISC DG4 Eq 3.24

Resistance factor-LRFD φ = 1.00 AISC 341-16 E3.6e (1)

φ Rn = = 113.6 [kips]
Unbalanced force to be resisted by
R s = P uf - φ R n = 45.9 [kips]
transverse stiffeners

23/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Column Web Buckling 159.4 / 71.9 N/A

Flange force moment arm d m = d b - t fb = 17.375 [in]

Seismic flange force P uf_c = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

h = dc - 2 kc = 10.860 [in]

Column yield strength F yc = 50.0 [ksi] E c = 29000 [ksi]

Distance from top of beam flange to

d end-flg = 13.000 [in] beam flange t fb = 0.525 [in]
top of column

Distance from center of flange force

d end-F = d end-flg + 0.5 t fb = 13.263 [in]
to top of column
d end-F ≥ d c /2 , R n has no reduction AISC 15 th J10.5

Top column reduction factor C t = 1.0 AISC 15 th J10.5

Column web buckling strength Rn =

C t 24 t 3wc √ E c F yc = 71.9 [kips] AISC 15 th Eq J10-8
h

Resistance factor-LRFD φ = 1.00 AISC 341-16 E3.6e (1)

φ Rn = = 71.9 [kips]
Unbalanced force to be resisted by
R s = P uf_c - φ R n = 87.6 [kips]
transverse stiffeners

Seismic Column Web Crippling 159.4 / 146.0 N/A

Flange force moment arm d m = d b - t fb = 17.375 [in]

Seismic flange force P uf_c = see Seismic Moment and Beam = 159.4 [kips]
Flange Force Calc

Column section d c = 12.500 [in] t fc = 0.520 [in]

t wc = 0.300 [in] k c = 0.820 [in]

Column yield strength F yc = 50.0 [ksi] E c = 29000 [ksi]

Beam flange fillet weld size w = 0.438 [in] beam flange t fb = 0.525 [in]

End plate thickness t p = 0.625 [in]

Length of bearing l b = t fb + 2 w + 2 t p = 2.650 [in]

Distance from top of column to top

d end-flg = = 13.000 [in]
of beam flange
Distance from top of column to
d end-F = d end-flg + 0.5 t fb = 13.263 [in]
center of flange force

d end-F ≥ d c /2 , use Eq J10-4 AISC 15 th Eq J10-4

lb t wc
2
Column web crippling strength R n = 0.8 t wc [1+3 ( ) 1.5]x = 146.0 [kips] AISC 15 th Eq J10-4
dc t fc

E c F yc t fc 0.5
( )
t wc
Resistance factor-LRFD φ = 1.00 AISC 341-16 E3.6e (1)

φ Rn = = 146.0 [kips]
Unbalanced force to be resisted by
R s = P uf_c - φ R n = 13.5 [kips]
transverse stiffeners

24/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Column Panel Zone Shear N/A

For OMF connection, there is no additional panel zone check requirements for amplified seismic load. AISC 341-16 E1.6b

Panel zone shear strength should be checked in accordance with Section J10.6 of the Specification.
The required shear strength of the panel zone should be based on the beam end moments computed from
the load combinations stipulated by the applicable building code, not including the amplified seismic load.

Seismic Stiffener Geometry Restriction PASS

Stiffener plate width b s = 3.130 [in] depth d s = 11.460 [in]

Stiffener plate thickness t s = 0.500 [in]

Column flange thickness t fc = 0.520 [in] column depth d c = 12.500 [in]

Beam flange thickness t fb = 0.525 [in]

Min Stiffener Plate Thickness

Min stiffener plate thickness t smin = max ( t fb / 2 , b s / 16 ) = 0.263 [in] AISC 15 th J10.8 (2)

Stiffener plate thickness ts = = 0.500 [in]

≥ t smin OK

Min Stiffener Plate Depth

Min stiffener plate depth d smin = ( d c - 2 t fc ) / 2 = 5.730 [in] AISC 15 th J10.8 (3)

Stiffener plate depth ds = = 11.460 [in]

≥ d smin OK

Seismic Stiffener Yield at Column Flange ratio = 87.6 / 77.1 = 1.14 FAIL

Stiffener plate width b s = 3.130 [in] thickness t s = 0.500 [in]

th
Stiffener plate corner clip clip = = 0.750 [in] AISC 15 Page 8-18

Stiffener plate yield strength Fy = = 36.0 [ksi]

2
Stiffener plate cross sect area A st = ( b s - clip ) t s = 1.190 [in ]

Trans stiffener strength required Rs = = 87.6 [kips]

th
Trans stiffener strength provided R n = F y x 2 x A st = 85.7 [kips] AISC 15 Eq J4-1
th
Bolt resistance factor-LRFD φ = 0.90 AISC 15 Eq J4-1

φ Rn = = 77.1 [kips]

ratio = 1.14 < Rs NG

Seismic Stiffener Shear at Column Web ratio = 87.6 / 215.1 = 0.41 PASS

Stiffener plate depth d s = 11.460 [in] thickness t s = 0.500 [in]

th
Stiffener plate corner clip clip = = 0.750 [in] AISC 15 Page 8-18

Stiffener plate yield strength Fy = = 36.0 [ksi]

2
Stiffener plate cross sect area A gv = ( d s - 2 x clip ) t s = 4.980 [in ]

Trans stiffener strength required Rs = = 87.6 [kips]

th
Trans stiffener strength provided R n = 2 x 0.6 x F y x A gv = 215.1 [kips] AISC 15 Eq J4-3
th
Resistance factor-LRFD φ = 1.00 AISC 15 Eq J4-3

φ Rn = = 215.1 [kips]

ratio = 0.41 > Rs OK

25/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Stiffener Compression ratio = 87.6 / 64.0 = 1.37 FAIL

Column section d = 12.500 [in] t f = 0.520 [in]

Stiffener plate depth ds = d - 2 tf = 11.460 [in]

Stiffener plate width b s = 3.130 [in] thickness t s = 0.500 [in]

Stiffener plate corner clip clip = = 0.750 [in] AISC 15 th Page 8-18

Stiffener plate yield strength F y = 36.0 [ksi] E = 29000 [ksi]

Stiffener plate cross sect area A st = ( b s - clip ) t s = 1.190 [in 2]

Stiffener plate unbraced length L = ds = d - 2 tf = 11.460 [in]

Plate radius of gyration r = ts / √ 12 = 0.144 [in]

Stiffener plate slenderness KL/r = 0.75 x L / r = 59.55

2
π E
Elastic buckling stress Fe = = 80.72 [ksi] AISC 15 th Eq E3-4
( KL/r ) 2

KL E
when ≤ 4.71 ( ) 0.5 = 133.68 AISC 15
th
E3
r Fy
( Fy / Fe )
Critical stress F cr = 0.658 Fy = 29.87 [ksi] AISC 15 th Eq E3-2

Trans stiffener strength required Rs = = 87.6 [kips]

th
Trans stiffener strength provided R n = 2 x F cr x A st = 71.1 [kips] AISC 15 Eq E3-1
th
Bolt resistance factor-LRFD φ = 0.90 AISC 15 E1

φ Rn = = 64.0 [kips]

ratio = 1.37 < Rs NG

Seismic Stiffener to Column Flange Fillet Weld Limitation PASS

Min Fillet Weld Size

Thinner part joined thickness t= = 0.500 [in]

th
Min fillet weld size allowed w min = = 0.188 [in] AISC 15 Table J2.4

Fillet weld size provided w= = 0.250 [in]

≥ w min OK

Min Fillet Weld Length

Fillet weld size provided w= = 0.250 [in]

Min fillet weld length allowed L min = 4 x w = 1.000 [in] AISC 15 th J2.2b

Min fillet weld length L = b s - clip = 2.380 [in]

≥ L min OK

Min Stiffener to Column Flange Fillet Weld Size

Stiffener plate to column flange fillet weld to develop the yield strength of the stiffener plate AISC DG13 Eq 4.3-6

Shear resistance factor-LRFD φ v = 0.90 AISC 15 th G1

Fillet weld shear strength φ R n-w = = 1.392 [kip/in] AISC 15 th Eq 8-2a

Fillet weld strength φ R n-w x 1.5 x 2 to account for 90° load angle when it's in tension and double fillet

Stiffener plate thickness t s = 0.500 [in] F y = 36.0 [ksi]

Min double fillet weld size to match
D min = φ v F y t s / ( φ R n-w x 1.5 x 2 ) = 3.879 [1/16 "]
stiffener plate yield strength
Fillet weld size provided D= = 4.000 [1/16 "]

≥ D min OK

26/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Stiffener to Column Web Fillet Weld Limitation PASS

Min Fillet Weld Size

Thinner part joined thickness t= = 0.300 [in]

Min fillet weld size allowed w min = = 0.188 [in] AISC 15 th Table J2.4

Fillet weld size provided w= = 0.250 [in]

≥ w min OK

Min Fillet Weld Length

Fillet weld size provided w= = 0.250 [in]

th
Min fillet weld length allowed L min = 4 x w = 1.000 [in] AISC 15 J2.2b

Min fillet weld length L = d c - 2 x t fc - 2 x clip = 9.960 [in]

≥ L min OK

Seismic Stiffener Weld Strength at Column Flange ratio = 87.6 / 79.5 = 1.10 FAIL

Stiffener to Column Flange Weld Length Calc

Stiffener plate width & clip b s = 3.130 [in] clip = 0.750 [in]
Stiffener to column flange weld
L = ( b s - clip ) x 2 stiffener = 4.760 [in]
length - double fillet

Trans stiffener strength required Rs = = 87.6 [kips]

Fillet Weld Strength Check

Fillet weld leg size w = 1⁄ 4 [in] load angle θ = 90.0 [°]

Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 th Table 8-3

Number of weld line n=2 for double fillet

Load angle coefficient C 2 = ( 1 + 0.5 sin 1.5 θ ) = 1.50 AISC 15 th Page 8-9

Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 22.271 [kip/in] AISC 15 th Eq 8-1

Base metal - stiffener plate thickness t = 0.500 [in] tensile F u = 58.0 [ksi]

Base metal - stiffener plate is in tension, tensile rupture as per AISC 15 th Eq J4-2 is checked AISC 15 th J2.4

Base metal tensile rupture R n-b = F u t = 29.000 [kip/in] AISC 15 th Eq J4-2

For seismic nonductile limit state, weld strength use φ = 0.75 , base metal rupture use φ n = 0.9
AISC 358-16 2.4.1
Increase base metal rupture strength due to higher φ value when compare to weld strength

0.90
Double fillet linear shear strength R n = min ( R n-w , R n-b x ) = 22.271 [kip/in] AISC 15 th Eq 9-2
0.75

Resistance factor-LRFD φ = 0.75 AISC 15 th Eq 8-1

φ Rn = = 16.703 [kip/in]

Shear resistance required Rs = = 87.6 [kips]

Fillet weld length - double fillet L= = 4.760 [in]

Shear resistance provided φ Fn = φ Rn x L = 79.5 [kips]

ratio = 1.10 < Rs NG

27/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

Seismic Stiffener Weld Strength at Column Web ratio = 87.6 / 221.8 = 0.39 PASS

Stiffener to Column Web Weld Length Calc

Column section d c = 12.500 [in] t fc = 0.520 [in]

Stiffener plate corner clip clip = 0.750 [in]

Stiffener to column web weld length

L = (d c - 2 x t fc - 2 x clip) x 2 stiffener = 19.920 [in]
- double fillet

Trans stiffener strength required Rs = = 87.6 [kips]

Fillet Weld Strength Check

1
Fillet weld leg size w = ⁄4 [in] load angle θ = 0.0 [°]
th
Electrode strength F EXX = 70.0 [ksi] strength coeff C 1 = 1.00 AISC 15 Table 8-3

Number of weld line n=2 for double fillet

1.5 th
Load angle coefficient C 2 = ( 1 + 0.5 sin θ) = 1.00 AISC 15 Page 8-9
th
Fillet weld shear strength R n-w = 0.6 (C 1 x 70 ksi) 0.707 w n C 2 = 14.847 [kip/in] AISC 15 Eq 8-1

Base metal - stiffener plate thickness t = 0.500 [in] tensile F u = 58.0 [ksi]
th
Base metal - stiffener plate is in shear, shear rupture as per AISC 15 Eq J4-4 is checked AISC 15 th J2.4

Base metal shear rupture R n-b = 0.6 F u t = 17.400 [kip/in] AISC 15 th Eq J4-4

For seismic nonductile limit state, weld strength use φ = 0.75 , base metal rupture use φ n = 0.9
AISC 358-16 2.4.1
Increase base metal rupture strength due to higher φ value when compare to weld strength

0.90
Double fillet linear shear strength R n = min ( R n-w , R n-b x ) = 14.847 [kip/in] AISC 15 th Eq 9-2
0.75

th
Resistance factor-LRFD φ = 0.75 AISC 15 Eq 8-1

φ Rn = = 11.135 [kip/in]

Shear resistance required Rs = = 87.6 [kips]

Fillet weld length - double fillet L= = 19.920 [in]

Shear resistance provided φ Fn = φ Rn x L = 221.8 [kips]

ratio = 0.39 > Rs OK

28/29
8/4/2019 AISC Steel Connection Design http://asp.civilbay.com/connect Moment Connection OMF MC-2

29/29