Approval

TO :
DATE : Oct, 11. 2011

SAMSUNG TFT-LCD

MODEL NO : LTN156AT24-W

NOTE : Extension code [ -W ]

→ LTN156AT24-W**
Surface type [ Glare ]

Any modification of Spec is not allowed without SEC’s permission

APPROVED BY :

PREPARED BY : Jina Kim

Application Engineer Group

SAMSUNG ELECTRONICS CO., LTD.
Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 1 / 33

 Approval
CONTENTS

Revision History -------------------( 3 )

General Description -------------------( 4 )

1. Absolute Maximum Ratings -------------------( 5 )

1.1 Absolute Ratings of environment
1.2 Electrical Absolute Ratings

2. Optical Characteristics -------------------( 7 )

3. Electrical Characteristics - - - - - - - - - - - - - - - - - - - ( 10 )
3.1 TFT LCD Module
3.2 Backlight Unit
3.3 LED Driver

4. Block Diagram - - - - - - - - - - - - - - - - - - - ( 13 )
4.1 TFT LCD Module
4.2 Back-Light Unit

5. Input Terminal Pin Assignment - - - - - - - - - - - - - - - - - - - ( 14 )

5.1 Input Signal & Power
5.2 LVDS Interface
5.3 Timing Diagrams of LVDS For Transmitting
5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color.
5.5 Pixel format

6. Interface Timing - - - - - - - - - - - - - - - - - - - ( 21 )
6.1 Timing Parameters
6.2 Timing Diagrams of interface Signal
6.3 Power ON/OFF Sequence

7. Outline Dimension - - - - - - - - - - - - - - - - - - - ( 23)

8. Packing -- - - - - - - - - - - - - - - - - - ( 25 )

9. Markings & Others -- - - - - - - - - - - - - - - - - - ( 26 )

10. General Precautions - - - - - - - - - - - - - - - - - - - ( 28 )

11. EDID - - - - - - - - - - - - - - - - - - - ( 31 )

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 2 / 33

 REVISION HISTORY Approval

Date Revision No. Page Summary

Oct, 11, 2011 A00 The Approval specification of LTN156AT24-W was issued first.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 3 / 33

 Approval
GENERAL DESCRIPTION
DESCRIPTION
LTN156AT24-P is a color active matrix TFT (Thin Film Transistor) liquid crystal display
(LCD) that uses amorphous silicon TFT as switching devices. This model is composed of a
TFT LCD panel, a driver circuit and a backlight system. The resolution of a 15.6" contains
1366 x 768 pixels and can display up to 262,144 colors. 6 O'clock direction is the Optimum
viewing angle.

FEATURES
• Thin and light weight
• High contrast ratio, high aperture structure
• 1366 x 768 pixels resolution (16:9)
• Fast Response Time
• Low power consumption
• LED BLU Structure
• DE (Data enable) only mode
• 3.3V LVDS Interface
• On board EDID chip
• Pb-free product

APPLICATIONS
• Notebook PC
• If the usage of this product is not for PC application, but for others, please contact SEC

GENERAL INFORMATION

Item Specification Unit Note

Display area 344.232 (H) x 193.536 (V) (15.6”diagonal) mm

Driver element a-Si TFT active matrix

Display colors 262,144

Number of pixel 1366 x 768 pixel 16 : 9

Pixel arrangement RGB vertical stripe

Pixel pitch 0.252 (H) x 0.252 (V) (TYP.) mm

Display Mode Normally white

Surface treatment Haze 0, Hardness 3H Glare

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 4 / 33

 Approval
Mechanical Information
Item Min. Typ. Max. Unit Note
Horizontal (H) 358.8 359.3 359.8 mm
Module
Vertical (V) 209.0 209.5 210 mm
size
Depth (D) - - 5.5 mm (1)
Weight - - 450 g

Note (1) Measurement condition of outline dimension

. Equipment : Vernier Calipers
. Push Force : 500g f (minimum)

1. ABSOLUTE MAXIMUM RATINGS

1.1 ENVIRONMENTAL ABSOLUTE RATINGS

Item Symbol Min. Max. Unit Note

Storage temperate TSTG -20 60 C (1)
Operating temperate
TOPR 0 50 C (1)
(Temperature of glass surface)
Shock ( non-operating ) Snop - 240 G (2),(4)
Vibration (non-operating) Vnop - 2.41 G (3),(4)

Note (1) Temperature and relative humidity range are shown in the figure below.
95 % RH Max. (40 C  Ta)
Maximum wet - bulb temperature at 39 OC or less. (Ta  40 C ) No condensation

Relative Humidity ( %RH)

100 90
( 40,90 )

80

60
Operating Range
( 50,50.4 )
40
( 60,27.7 )
20

5
Storage Range
0
-40 -20 0 20 40 60 80

Temperature (OC)
(2) 2ms, half sine wave, one time for X, Y,  Z.
(3) 5 - 500 Hz, random vibration, 30min for X, Y, Z.
(4) At testing Vibration and Shock, the fixture in holding the Module to be tested have to be
hard and rigid enough so that the Module would not be twisted or bent by the fixture.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 5 / 33

 Approval
1.2 ELECTRICAL ABSOLUTE RATINGS

(1) TFT LCD MODULE

VDD =3.3V, VSS = GND = 0V

Item Symbol Min. Max. Unit Note

Power Supply Voltage VDD VDD – 0.3 VDD + 0.3 V (1)

Logic Input Voltage Vin VDD – 0.3 VDD + 0.3 V (1)

Note (1) Within Ta (25  2 C )

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 6 / 33

 Approval
2. OPTICAL CHARACTERISTICS

The following items are measured under stable conditions. The optical characteristics
should be measured in a dark room or equivalent state with the methods shown in Note (5).
Measuring equipment : TOPCON SR-3

* Ta = 25  2 C, VDD=3.3V, fv= 60Hz, fDCLK = 78.05 MHz

Conditio
Item Symbol Min. Typ. Max Unit Note
n

Contrast Ratio (1), (2),

CR 300 400 -
(5 Points) (5)

Response Time at Ta
TRT - 16 - msec (1), (3)
( Rising + Falling )

Average Luminance IL=115mA

YL,AVE 190 220 - cd/m2
of White (5 Points) (1), (4)
Normal
RX Viewing 0.615
Red Angle
RY =0 0.355
=0
GX 0.335
Green
Color GY 0.610
TYP TYP
Chromaticity -
BX -0.03 0.150 +0.03
( CIE )
Blue
BY 0.100

WX 0.313
White
WY 0.329

L 40 45 -
Hor.
Viewing R 40 45 - Degrees (1), (5)
CR  10
Angle H 15 15 - SR-3
Ver.
L 30 30 -

Color Gamut - 60 - %

13 Points
L - - 1.7 - (6)
White Variation

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 7 / 33

 Note 1) Definition of Viewing Angle : Viewing angle range(10  C/R) Approval
Normal Line
 = 0o,  = 0o

L
R
H 12 O’clock
L
 L =90o x y direction
 H = 90o

6 O’clock y' x'

direction
R =90o
 L= 90o

Note 2) Definition of Contrast Ratio (CR) : Ratio of gray max (Gmax) ,gray min (Gmin)
at 5 points (33, 55, 77, 37, 73)

CR(33) + CR(55) + CR(77) + CR(37) + CR(73)

CR =
5

Points : 33, 55, 77, 37, 73 at the figure of Note (6).

Note 3) Definition of Response time :

Display data White(TFT OFF) Black(TFT ON) White(TFT OFF)

TR TF
100%
90%
Optical
Response
10%
0%
Time
Note 4) Definition of Average Luminance of White : measure the luminance of white at 5 points.

(30%) (50%) (70%)

VIEW AREA

Average Luminance of White ( YL,AVE ) 33 37

(30%)
55
YL33 + YL55 + YL77 + YL37 + YL73 (50%)
YL,AVE = 73 77
5 (70%)

: test point
Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 8 / 33

 Approval
Note 5) After stabilizing and leaving the panel alone at a given temperature for 30 min , the measurement
should be executed. Measurement should be executed in a stable, windless, and dark room.
30 min after lighting the backlight. This should be measured in the center of screen.
LED current : 115.0mA
Environment condition : Ta = 25  2 C

Photo-detector
( TOPCON SR-3 )

Field = 2
50 cm

TFT-LCD module LCD panel

Center of the screen

[ Optical characteristics measurement setup ]

Note 6) Definition of 13 points white variation ( L ), [ 1 ~ 13 ]

Maximum luminance of 13 points
L =
Minimum luminance of 13 points

10mm 10mm
25% 50% 75%
10mm
13 12 11

10 9 25%

8 7 6 50% : test point

5 4 75%

3 2 1
10mm

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 9 / 33

3. ELECTRICAL CHARACTERISTICS Approval
3.1 TFT LCD MODULE
Ta= 25  2C

Item Symbol Min. Typ. Max. Unit Note

Voltage of Power Supply VDD 3.0 3.3 3.6 V

Differential Input High VIH - - +100 mV VCM = +1.2V

Voltage for LVDS
Receiver Threshold Low VIL -100 - - mV

Vsync Frequency fv - 60 - Hz

Main Frequency fDCLK - 78.05 - MHz

Rush Current IRUSH - - 1.5 A (4)

White - 240 - mA (2),(3)*a

Current of Power IDD
Mosaic - 240 264 mA (2),(3)*b
Supply
V. Stripe - 400 450 mA (2),(3)*c

Note (1) Display data pins and timing signal pins should be connected.( GND = 0V )
(2) fV = 60Hz, fDCLK = 78.05 MHZ, VDD = 3.3V , DC Current.
(3) Power dissipation pattern

*a) White Pattern *b) Mosaic Pattern

VIEW AREA

Display Brightest Gray Level

Display Darkest Gray Level

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 10 / 33

 Approval
*c) 1dot Vertical stripe pattern

RG B R G B R G B R G

RG B R G B R G B R G

RG B R G B R G B R G

RG B R G B R G B R G

4) Rush current measurement condition

3.3V M1
2SK1059
VDD ( LCD INPUT)
FUSE
R1 C1
47K 1uF

R2
CONTROL SIGNAL M2
(HIGH to LOW) 2SK1399
1K

12V
R3 C2

C3 47K
10000pF
1uF

VDD rising time is 470us

3.3V
0.9VDD

0.1VDD
GND
470us

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 11 / 33

 Approval

3.2 BACK-LIGHT UNIT Ta= 25  2 C

Item Symbol Min. Typ. Max. Unit Note

LED Forward Current IF - 115 - mA
LED Forward Voltage VF 6.2 6.6 7.2 V

LED Array Voltage VP - 26.4 - V VF X 4 LEDs

Power Consumption P - - 3.9 W

Operating Life Time Hr 10,000 - - Hour (1)

Note (1) When the brightness becomes 50% or lower than the original.

3.3 LED Driver

- LED Driver Manufacturer : Richtek (RT8510GQW) Ta= 25  2 C

Item Symbol Min. Typ. Max. Unit Note

Input Voltage Vin 6 12 24 V

PWM Freq. :
10 - 100 %
1kHz~10KHz
Burst Ratio D
PWM Freq. :
5 - 100 %
0.2KHz~1KHz

External PWM Vin=6~24V,

Dimming Control FBLIM 0.2 - 100 KHZ BLIM=PWM
Frequency (BLIM) 0V~3.3V

Output Power Pout - - 3.9 W @ 220nit

Note - Test Equipment : Fluke 45

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 12 / 33

 Approval
4. BLOCK DIAGRAM
4.1 TFT LCD Module

I2 C bus EDID
EEPROM
LVDS
m-LVDS signal
Input Connector LVDS Input/LCDS Output
(40P) Timing Controller
Source
Driver
IC 15.6” HD
DC-DC (m-LVDS)
TFT-LCD Panel
Converter
Gamma
VCOM
Generator
Generator

Video Signal
Control Signal
VCOM
Gamma
DVDD SOURCE PCB
AVDD TFT on Glass
Von/Voff

4.2 LED connection and placement

1 2 3 4
Channel 1

LED #1 #2 #3 #4
LED Wiring LED Placement

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 13 / 33

 Approval
5. INPUT TERMINAL PIN ASSIGNMENT
5.1. Input Signal & Power (LVDS, Connector : I-PEX 20455-040E-12)

PIN # Symbol Description

1 NC NOT CONNECT
2 VDD Power (Vdd = 3.3V)
3 VDD Power (Vdd = 3.3V)
4 VCC EDID VCC_EDID
5 WPN WPN
6 SCL CLOCK FOR EDID

7 SDA DATA FOR EDID

8 O_RXIN0- LVDS Oth Signal Negative(Odd)

9 O_RXIN0+ LVDS Oth Signal Positive(Odd)
10 GND Ground
11 O_RXIN1- LVDS 1st Signal Negative(Odd)
12 O_RXIN1+ LVDS 1st Signal Positive(Odd)
13 GND Ground
14 O_RXIN2- LVDS 2nd Signal Negative(Odd)
15 O_RXIN2+ LVDS 2nd Signal Positive(Odd)
16 GND Ground
17 O_RXCLKIN- LVDS Clock Signal Negative(Odd)
18 O_RXCLKIN+ LVDS Clock Signal Positive(Odd)

19~25 NC No connection
26~30 NC No connection
31 GND Ground
32 GND Ground
33 GND Ground
34 NC NOT CONNECT
35 PWM PWM
36 BLEN BL ENABLE
37 NC NOT CONNECT
38 VBL B/L VCC 6V~24V
39 VBL B/L VCC 6V~24V
40 VBL B/L VCC 6V~24V

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 14 / 33

 Approval
5.2 LVDS Interface : Transmitter DS90CF363 or Compatible

Pin No. Name RGB Signal Pin No. Name RGB Signal

51 TxIN0 R0 14 TxIN14 G5

52 TxIN1 R1 15 TxIN15 B0

54 TxIN2 R2 19 TxIN18 B1

55 TxIN3 R3 20 TxIN19 B2

56 TxIN4 R4 22 TxIN20 B3

3 TxIN6 R5 23 TxIN21 B4

4 TxIN7 G0 24 TxIN22 B5

6 TxIN8 G1 27 TxIN24 Hsync

7 TxIN9 G2 28 TxIN25 Vsync

11 TxIN12 G3 30 TxIN26 DE

12 TxIN13 G4 31 TxCLKIN Clock

LVDS INTERFACE

Graphics controller DS90CF383 I-PEX 20455-040E Integrated IC

18-bit RED0 51 48
RED1 52 TxOUT0- 8 RxIN0-
RED2 54 47 100 
RED3 55 TxOUT0+ 9 RxIN0+
RED4 56
RED5 3 46
GREEN0 4 TxOUT1- 11 RxIN1-
GREEN1 6 100
45
GREEN2 7 TxOUT1+ 12 RxIN1+
GREEN3 11
GREEN4 12
42
GREEN5 14 TxOUT2- 14 RxIN2-
BLUE0 15 100 
41
BLUE1 19 TxOUT2+ 15 RxIN2+
BLUE2 20
BLUE3 22 40
BLUE4 23 TxCLKOUT- 17 RxCLKIN-
BLUE5 24 100 
39
Hsync 27 TxCLKOUT+ 18 RxCLKIN+
Vsync 28
Enable 30
CLOCK 31
Note : The LCD Module uses a 100ohm resistor between positive and negative lines of each
receiver input.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 15 / 33

 Approval
5.2 LVDS Interface
5.2.1 LVDS DC Input

ITEM SYMBOL MIN. TYP. MAX. UNIT NOTE

LVDS Differential Voltage |VID| 100 350 600 mV
Input Common Mode
VCM 0.4 1.2 1.8 V
Voltage

5.2.2 LVDS AC Input

ITEM SYMBOL MIN. TYP. MAX. UNIT NOTE

LVDS input clock frequency FCLK_LVD 20 90 MHz

S
90MHz > FCLK_LVDS ≥
RIN -400 0 400 ps (1),(2)
65MHz
skew TRSRM
margin 65MHz > FCLK_LVDS ≥
-600 0 600 ps (1),(2)
20MHz

Modulating frequency of LVDS

FCLK_MOD 300 KHz (3)
input clock during SSCG
Maximum deviation of LVDS input FCLK_D
- - ±3 % (3)
clock during SSCG EV

Note (1) : LVDS Receiver Skew (Strobe) Margin

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 16 / 33

 Approval

Note (2) : Ideal Strove Positions for LVDS Input

Note (3) : SSC ( Spread Spectrum Clock)

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 17 / 33

 Approval
5.3 Timing Diagrams of LVDS For Transmission

LVDS Receiver : Integrated T-CON

T
TxCLK OUT
RxCLK IN

T/7

Rx IN2 RxOUT20 RxOUT19 RxOUT18 RxOUT17 RxOUT16 RxOUT15 RxOUT14

DE Vsync Hsync B5 B4 B3 B2

Rx IN1 RxOUT13 RxOUT12 RxOUT11 RxOUT10 RxOUT9 RxOUT8 RxOUT7

B1 B0 G5 G4 G3 G2 G1

RxIN0 RxOUT6 RxOUT5 RxOUT4 RxOUT3 RxOUT2 RxOUT1 RxOUT0

G0 R5 R4 R3 R2 R1 R0

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 18 / 33

 Approval
5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color
Data Signal Gray
Color Display Red Green Blue Scale
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 45 B5 Level

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 -
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 -
Basic Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 -
Colors Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 -
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 -
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 -
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0
Dark 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1

Gray  0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
Scale : : : : : : : : : : : : : : : : : : :
R3R60
Of : : : : : : : : : : : : : : : : : : :
Red  1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R61
Light 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R62
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R63
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0
Dark 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 G1

Gray  0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 G2
Scale : : : : : : : : : : : : : : : : : : :
G3G60
Of : : : : : : : : : : : : : : : : : : :
Green  0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 G61
Light 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 G62
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 G63
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0
Dark 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 B1

Gray  0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 B2
Scale : : : : : : : : : : : : : : : : : : :
B3B60
Of : : : : : : : : : : : : : : : : : : :
Blue  0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 B61
Light 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 B62
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 B63
Note 1) Definition of gray :
Rn: Red gray, Gn: Green gray, Bn: Blue gray (n=gray level)
Note 2)Input signal: 0 =Low level voltage, 1=High level voltage
Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 19 / 33

 Approval
5.5 Pixel Format in the display

Pixel 1 Pixel 1366

Line 1 R G B R G B R G B R G B

LTN156AT24-P**

Line 768 R G B R G B R G B R G B

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 20 / 33

6. INTERFACE TIMING
Approval

6.1 Timing Parameters

Signal Item Symbol Min. Typ. Max. Unit Note

Frame Frequency Cycle TV 773 790 810 lines -

Vertical Active Display

TVD - 768 - Lines -
Display Term Period

One Line
Cycle TH 1426 1526 1726 Clocks -
Scanning Time

Horizontal Active Display

THD - 1366 - Clocks -
Display Term Period

6.2 Timing diagrams of interface signal

TV

TVD

DE

TH

DCLK
TC
THD

DE

DATA Valid display data ( 1366 clocks)

SIGNALS

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 21 / 33

 6.3 Power ON/OFF Sequence Approval
: To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
should be as the diagram below.

0.9 VDD 0.9 VDD

0.1 VDD 0.1 VDD

Power Supply VDD
0V
T1 T7 T4

T2 T3

VALID
Signals
0V
T8 T9

T10 T11

0.9 Vin 0.9 Vin

LED Power (Vin) 0.1 Vin 0.1 Vin

0V T12 T13

PWM
0V T14 T15

B/L Enable
0V T5 T6

Timing (ms) Remarks

0.5＜T1≤10 VDD rising time from 10% to 90%

0＜T2 ≤50 Delay from VDD to valid data at power ON

0＜T3 ≤50 Delay from valid data OFF to VDD OFF at power Off

500 ≤T4 VDD OFF time for Windows restart

200 ≤T5 Delay from valid data to B/L enable at power ON

200 ≤T6 Delay from valid data off to B/L disable at power Off

0＜T7 ≤10 VDD falling time from 90% to 10%

10＜T8 Delay from valid data on to LED driver Vin rising time 10%

10＜T9 Delay from LED driver Vin falling time 10% to valid data Off

0.5＜T10≤10 LED Vin rising time from 10% to 90%

0.5＜T11≤10 LED Vin falling time from 90% to 10%

10＜T12 Delay from LED driver Vin rising time 90% to PWM ON

10＜T13 Delay from PWM Off to LED driver Vin falling time 10%

10＜T14 Delay from PWM ON to B/L Enable ON

10＜T15 Delay from B/L Enable Off to PWM Off

Note : Backlight may flash if interface signal remains floating state at invalid period.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 22 / 33

7. MECHANICAL OUTLINE DIMENSION
Approval

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 23 / 33

 Approval

I-PEX 20455-040E-02

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 24 / 33

 8. PACKING Approval
1. CARTON(Internal Package)

(1) Packing Form

Corrugated Cardboard box and Corrupad form as shock absorber

(2) Packing Method

Note (1) Total : Approx. 13Kg

(2) Acceptance number of piling : 22 sets
(3) Carton size : 283(W)×401(D)×263(H)

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 25 / 33

 (3)Packing Material
Approval
No Part name Quantity

1 Static electric protective sack 22

Packing case (Inner box)

2 1 set
included shock absorber

3 Pictorial marking 2 pcs

4 Carton 1 set

9. MARKINGS & OTHERS

A nameplate bearing followed by is affixed to a shipped product at the
specified location on each product.

(1)Parts number : LTN156AT24

(2)Revision code : 3 letters
(3)Lot number : X X X X XXX XX X W**
SEC Revision Code
Panel number
Cell ID
Lot ID
Month
Year
Product Code
Line

(5) Nameplate Indication ( Following example is only for reference )

LTN156AT24 40 mm
1114
XXXXXXXXXX W**
MADE IN CHINA

80 mm
Parts name : LTN156AT24
Lot number : XXXXXXXXXX
Inspected work week : 1114(2011 year, 14th week)
Product revision Code : W**

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 26 / 33

 Approval
(6) Packing small box attach

DEVICE : LTN156AT24
TYPE : W**
QUANTITY : 22 PCS

XXXXXXXXX

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 27 / 33

10. GENERAL PRECAUTIONS Approval

1. Handling

(a) When the module is assembled, It should be attached to the system firmly
using every mounting holes. Be careful not to twist and bend the modules.

(b) Refrain from strong mechanical shock and / or any force to the module. In addition to
damage, this may cause improper operation or damage to the module and LED back-light.

(c) Note that polarizers are very fragile and could be easily damaged. Do not press or scratch
the surface harder than a HB pencil lead.

(d) Wipe off water droplets or oil immediately. If you leave the droplets for a long time,
Staining and discoloration may occur.

(e) If the surface of the polarizer is dirty, clean it using some absorbent cotton or soft cloth.

(f) The desirable cleaners are water, IPA (Isoprophyl Alcohol) or Hexane.
Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl
chloride. It might permanent damage to the polarizer due to chemical reaction.

(g) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or
mouth . In case of contact with hands, legs or clothes, it must be washed away thoroughly
with soap.

(h) Protect the module from static , it may cause damage to the C-MOS Gate Array IC.

(i) Use fingerstalls with soft gloves in order to keep display clean during the incoming
inspection and assembly process.

(j) Do not disassemble the module.

(k) Do not pull or fold the lamp wire.

(l) Do not adjust the variable resistor which is located on the back side.

(m) Protection film for polarizer on the module shall be slowly peeled off just before use so
that the electrostatic charge can be minimized.

(n) Pins of I/F connector shall not be touched directly with bare hands.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 28 / 33

2. STORAGE Approval

ITEM Unit Min. Max.

Storage Temperature (℃) 5 40
Storage Humidity (%rH) 35 75
Storage life 12 months

-The storage room should provide good ventilation and temperature

control.
- Products should not be placed on the floor, but on the Pallet away
from a wall.
- Prevent products from direct sunlight, moisture nor water; Be
cautious of a build up of condensation.
Storage Condition - Avoid other hazardous environment while storing goods.
- If products delivered or kept in conditions of over the storage
period of 3 months, the recommended temperature or humidity
range.
we recommend you leave the at a temperature of 20℃ and a
humidity of 50% for 24 hours.

3. OPERATION

(a) Do not connect, disconnect the module in the “ Power On” condition.

(b) Power supply should always be turned on/off by following item 6.3
“ Power on/off sequence “.

(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference shall be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.

(d) The standard limited warranty is only applicable when the module is used for general
notebook applications. If used for purposes other than as specified, SEC is not to be
held reliable for the defective operations. It is strongly recommended to contact SEC
to find out fitness for a particular purpose.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 29 / 33

 Approval
4. OTHERS
(a) Ultra-violet ray filter is necessary for outdoor operation.

(b) Avoid condensation of water. It may result in improper operation or disconnection

of electrode.

(c) Do not exceed the absolute maximum rating value. ( the supply voltage variation, input
voltage variation, variation in part contents and environmental temperature, so on)
Otherwise the module may be damaged.

(d) If the module displays the same pattern continuously for a long period of time,it can be
the situation when the image “sticks” to the screen.

(e) This module has its circuitry PCB’s on the rear side and should be handled carefully in
order not to be stressed.

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 30 / 33

11. EDID Approval

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 31 / 33

 Approval

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 32 / 33

 Approval

Samsung Secret

Doc.No. LTN156AT24-W Rev.No 04-A00-G-111011 Page 33 / 33