Scribd
Upload
114 views5 pages

SetupWizard-SettingUpDCS-930L - DCS-932LviaSetupWizardSoftware

This document provides a 7 step procedure for setting up a DCS-930L or DCS-932L IP camera using the D-Link Setup Wizard software: 1. Install and run the Setup Wizard software from the included CD 2. The software will display the camera's IP address and MAC address 3. Change the default admin username and password for security 4. Configure the camera's IP settings either via DHCP or static IP 5. For wireless, configure the SSID, channel, security settings to match the router 6. Restart the camera to save the network settings 7. Access the camera's web interface by entering its IP address in a browser

Uploaded by

Geekware Peru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
114 views5 pages

SetupWizard-SettingUpDCS-930L - DCS-932LviaSetupWizardSoftware

This document provides a 7 step procedure for setting up a DCS-930L or DCS-932L IP camera using the D-Link Setup Wizard software: 1. Install and run the Setup Wizard software from the included CD 2. The software will display the camera's IP address and MAC address 3. Change the default admin username and password for security 4. Configure the camera's IP settings either via DHCP or static IP 5. For wireless, configure the SSID, channel, security settings to match the router 6. Restart the camera to save the network settings 7. Access the camera's web interface by entering its IP address in a browser

Uploaded by

Geekware Peru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Technical Support Setup Procedure

Setup Wizard - Setting Up DCS-930L & DCS-932L WITH Setup Wizard Software

Step 1: Run the CD Set-Up that came with the DCS-930L/DCS-932L. Please install the Setup
Wizard.exe on your computer. After successful installation, go to Start>Programs>D-Link>D-Link
Setup Wizard, click to run the software.

Note: Please ensure you have connected your ip camera to the LAN port of your router.
Your PC is connected to the router via wired/wireless.

Step 2: Run the software. Your camera‟s IP Address will be displayed here along with its
corresponding MAC address. Click Wizard.
Step 3: You must change the Admin ID and password immediately to protect your camera against
unauthorized access. By default, the Admin ID and Password column are blank. To change the
Admin ID and password, check both Change Boxes and enter a new ID and password. Click Next.

Step 4: The default ip setting is DHCP, which means it will obtain the ip address assigned by your
router automatically. If you want to use Static IP, please enter the IP address, subnet mask,
default gateway and DNS settings for your camera. These settings must correspond with your
network settings for you to access the camera. Please check with your network administrator if you
are not sure of what these settings should be.
Step 5: For wireless connection setup, please configure the following:

Wireless: Enable

Connection Mode: Infrastructure

The Network Name (SSID), Wireless Channel, Security Mode, Authentication and Encryption
must correspond with the wireless network settings on your router. Click Next.

If you want to connect your camera via a network cable, please disable “Wireless”. Click Next.
Step 6: Click Back to modify your settings. Otherwise, click Restart to save your settings. Your setup
is now completed!

Step 7: Click Link button to launch the web browser and access to the WEB Interface of your camera.
You may access the WEB Interface directly by opening a web browser such as Internet Explorer,
Mozilla Firefox or Safari. On the address bar, type in the IP Address of the camera that you have
configured just now, in this example http://192.168.2.100, press Enter key on your keyboard.

Please enter the username and password that you have configured just now to login your camera.
Choose „ActiveX” or “Java”, it will prompt for you to install the plug-ins on your browser. After
installation completed, you may view the live video on your camera.

You might also like