AOR AR-ONE Operating Manual

American Communication Systems
Discover the Power of Communications ™

TO ORDER – VISIT http://www.ameradio.com
AR-ONE
Ultra Wide Band
Communications Receiver
Operating manual v.2.1
AOR, LTD.
March 1, 2010
Table of contents
1 Introduction ------------------------------------------------------------------------------------------------ 4
1-1 Introduction ----------------------------------------------------------------------------------- 4
1-2 Taking care of your radio ------------------------------------------------------------------- 5
1-3 Attention while operating ------------------------------------------------------------------ 6
1-4 Accessories supplied ----------------------------------------------------------------------- 8
1-5 Controls and functions --------------------------------------------------------------------- 8
1-5-1Keypad --------------------------------------------------------------------------- 10
1-5-2 Summary of keys ------------------------------------------------------------- 10
1-6 Computer control ---------------------------------------------------------------------------- 12
1-7 IF output and Spectrum Display Unit (SDU5600) ----------------------------------- 12
2 Getting Started -------------------------------------------------------------------------------------------- 13

2-1 Making the AR-ONE ready for operation ---------------------------------------------- 13
2-1-1 LCD ------------------------------------------------------------------------------ 13
2-1-2 Connect the antenna -------------------------------------------------------- 13
2-1-3 Connect power ---------------------------------------------------------------- 13
2-2 Switching on for the first time ------------------------------------------------------------ 13
2-3 Squelch Circuit -------------------------------------------------------------------------------14
2-4 VFO selection -------------------------------------------------------------------------------- 15
2-4-1 Tuning frequency ------------------------------------------------------------- 15
2-4-1-1 Entering frequency using the numeric keypad --------- 15
2-4-1-2 Changing frequency using the main tuning dial -------- 16
2-4-1-3 Changing frequency using UP/DOWN arrow key ----- 16
2-5 Changing receive mode ------------------------------------------------------------------- 16
2-5-1 Auto mode selection --------------------------------------------------------- 17
2-5-2 Receive mode selection ---------------------------------------------------- 18
2-6 Changing tuning step size ---------------------------------------------------------------- 18
2-7 IF bandwidth ---------------------------------------------------------------------------------- 19
2-7-1 Manually selecting IF band width -----------------------------------------20
2-8 AGC (Automatic Gain Control) -----------------------------------------------------------20
2-9 ATT (Attenuator) ----------------------------------------------------------------------------- 21
2-10 RF Amplifier ---------------------------------------------------------------------------------22
2-11 Offset ----------------------------------------------------------------------------------------- 23
2-11-1 Using pre-programmed frequency offset data ----------------------- 23
2-11-2 Entering new frequency offset data ------------------------------------ 23
1
3 Memory channels and banks ----------------------------------------------------------------------- 24
3-1 Memory channel overview -------------------------------------------------------------- 24
3-2 Storing VFO frequency and data into memory ------------------------------------- 25
3-3 Memory read “M.RD” --------------------------------------------------------------------- 26
3-4 Deleting memory channels -------------------------------------------------------------- 27
4 SCAN – scanning memory channels -------------------------------------------------------------28

4-1 SCAN – outline introduction ------------------------------------------------------------ 28
4-2 Starting SCAN ------------------------------------------------------------------------------ 28
4-3 Selecting a SCAN bank ------------------------------------------------------------------ 29
4-4 Select SCAN -------------------------------------------------------------------------------- 29
4-4-1 Adding select scan channels in memory read ----------------------- 29
4-4-2 Starting/Stopping select scan ------------------------------------------ 29
5 Search mode --------------------------------------------------------------------------------------------- 30

5-1 Search type --------------------------------------------------------------------------------- 30
5-1-1 Program search overview ------------------------------------------------ 30
5-2 Starting Program search ----------------------------------------------------------------- 31
5-2-1 Reversing the direction of search --------------------------------------- 31
5-2-2 Forcing the search to resume -------------------------------------------- 32
5-2-3 Stopping the search -------------------------------------------------------- 32
5-3 Selection of search bank ---------------------------------------------------- 32
5-4 Programming a search bank ----------------------------------------------------------- 32
5-5 Deleting search banks ------------------------------------------------------------------- 36
5-6 Locking out unwanted active frequencies (PASS) -------------------------------- 37
5-6-1 Deleting pass channels --------------------------------------------------- 38
6 Configuration menu ----------------------------------------------------------------------------------- 39

6-1 Configure beep ---------------------------------------------------------------------------- 40
6-2 Configure lamp ---------------------------------------------------------------------------- 41
6-3 Configure dimmer ------------------------------------------------------------------------- 42
6-4 Configure contrast ------------------------------------------------------------------------ 42
6-5 Configure manual AGC ------------------------------------------------------------------ 42
6-6 Configure IF-GAIN (Intermediate Frequency gain) ------------------------------- 43
6-7 Configure RF-GAIN (Radio Frequency gain) --------------------------------------- 44
2
6-8 Configure Remote BPS (Baud Rate) ------------------------------------------------- 44
6-9 Configure RMT-ID (Remote ID) -------------------------------------------------------- 45
6-10 Configure DELAY (Scan delay and Search delay) ------------------------------- 45
6-11 Configure FREE (Scan free and Search free) -------------------------------------46
6-12 Configure SPEAKER -------------------------------------------------------------------- 46
6-12-1 Configure rear speaker --------------------------------------------------- 47
6-12-2 Configure front speaker -------------------------------------------------- 47
6-12-3 Configure headphones output ------------------------------------------ 47
6-13 Configure audio filters (HPF/LPF) ---------------------------------------------------- 48
6-13-1 Configure audio HPF (High Pass) ------------------------------------- 48
6-13-2 Configure audio LPF (Low Pass Filter) ------------------------------ 49
6-14 Configure Audio De-emphasis -------------------------------------------------------- 49
6-15 Configure PRIO-CH (Priority Channel) --------------------------------------------- 49
6-15-1 Engaging PRIO channel ------------------------------------------------- 50
6-16 Configure IF output frequency -------------------------------------------------------- 51
6-16-1 Selecting IF output frequency ------------------------------------------ 51
6-17 Configure reference signal source --------------------------------------------------- 51
7 Computer control --------------------------------------------------------------------------------------- 52

7-1 How to send an RS-232C command ------------------------------------------------- 52
7-2 Power on the AR-ONE ------------------------------------------------------------------- 52
7-3 Detailed RS-232C Command Listing of the AR-ONE ---------------------------- 53
8 Reset -------------------------------------------------------------------------------------------------------- 66
9 Specifications -------------------------------------------------------------------------------------------- 67
10 Optional Accessories -------------------------------------------------------------------------------- 70
11 Limited Warranty (USA only) ---------------------------------------------------------------------- 71
3
1 Introduction
1-1 Introduction
Thank you for purchasing the AR-ONE Ultra Wide Band Communications receiver.
The AR-ONE is designed using the very latest technology to ensure the highest levels of
performance and reliability. To get the best possible results from your AR-ONE, we
strongly recommend you to read this manual and familiarize yourself with the receiver.
Although carefully designed, this receiver (like all receivers) suffer from a degree of
internal noise known as spurious emissions. They are a product of the receiver’s
circuitry, and therefore, do not represent a fault. Apparent faults may be due to
accidental misoperation of the receiver. If you believe there is a problem, carefully read
all of the manual before deciding to contact your dealer for advice.
It is acknowledged that sections of this manual are repetitive, this is to enable the
manual to be used as a reference book (you don’t have to read it all from cover to cover
in one go).
Every effort has been made to make this manual correct and up to date. Due to
continuous development of the receiver, and by error or omission anomalies may be
found and this is acknowledged.
© This manual is protected by copyright AOR, LTD. 2009. No information contained in

this manual may be copied or transferred by any means without the prior written consent
of AOR, LTD. AOR and the AOR logo are trademarks of AOR, LTD. All other trademarks
and names are acknowledged.
4
Main features:
Super wide coverage: 10 KHz ~ 3.3 GHz (continuous)

1,000 memory channels
10 VFOs
Monitor AM, NFM, WFM, USB, LSB, CW, Data
Ultra-stable reference frequency oscillator
Two RS-232C ports plus control head port
Control up to 99 AR-ONE Units with one PC
Triple conversion superheterodyne front end
Antenna input level readout
Adjustable BFO
High intercept
IF signal output (10.7 MHz or 455KHz)
Excellent sensitivity
Detachable control head (optional kit required)
1-2 Taking care of your radio
There are no internal operator adjustments. In the unlikely event of servicing being
required, please contact your dealer for technical assistance.
Do not use or leave the receiver in direct sunlight (especially the LCD). It is best to avoid
locations where excessive heat, humidity, dust and vibration are expected. Always keep
the AR-ONE free from dust and moisture. Use a soft, dry cloth to gently wipe the set
clean, never use abrasive cleaners or organic solvents which may damage certain
parts. Treat the AR-ONE with care, avoid spillage or leakage of liquids into the receiver
and associated power supply. Special care should be taken to avoid liquid entering
around the controls, through the speaker grille or via the connection jacks.
The AR-ONE is designed for operation from a good quality regulated DC supply of 12 to
14 V, which should be capable of supplying 1.5 A. Never connect the AR-ONE
directly to the AC outlet.
The chassis of the receiver is at negative ground. Where provided (depending upon
world market location), the power supply is pre-wired and provides a nominal 12 V DC
output with suitable connectors being fitted as standard for the AC power input and
connection to the AR-ONE.
5
SAFETY NOTICE – Always disconnect the power supply from the AC outlet when
not in use. If used mobile, it should be noted that the AR-ONE has NOT been
manufactured or tested to meet any specific mobile safety requirements.
The AR-ONE has no internally user adjustable parts.
If using the AR-ONE in a base station situation, the best short wave reception is usually
achieved by the fitting of a separate external earth rod, however, consider the
implications carefully if your AC building supply uses a Protective Multiple Earth (PME)
system. If in doubt consult an expert electrician. Never earth to a gas pipe!
The AR-ONE has a single N type antenna connector for all frequencies. This is intended
for connection to a 50 Ω (unbalanced) coaxial fed antenna such as a discone, dipole,
unipole, Yagi, etc. When sighting the antenna, avoid power cables. Ensure that you do
not confuse the antenna and other IF output connectors as they are closely located.
1-3 Attention while operating

1. Certain key operations are acted upon when the key is RELEASED, not while it
is pressed. Allow time for the AR-ONE to register such actions before pressing
another key.
2. The key lock (LOCK) is intentionally made to be difficult to operate to prevent
accidental operation. To release key lock, the LOCK key has to be held for
more than one second, the key icon on the LCD confirms operation. The LOCK
is disabled during keying sequences (such as when entering frequencies).
3. If a key sequence is not completed, the microprocessor will automatically abort
most operations after about 90 seconds of keypad inactivity.
4. Currently displayed VFO data is saved at power down (to increase speed of
operation and to reduce write cycles). For this reason, if the AR-ONE is
powered down using the PWR/VOL control or external power is removed, the
last displayed frequency will be lost and the frequency used prior to this will be
displayed when next powered up.
Terminology – Search & Scan
If you have not used a wide band receiver before or are not familiar with the terminology
used, it is very important to understand the difference between SEARCH and SCAN modes.
SEARCH: The AR-ONE provides several operations where transmissions (active

frequencies) may be automatically located by sweeping the receiver over a wide
6
frequency range, either from the currently displayed frequency traveling upwards
(or downwards) in a specified tuning increment (step) or by sweeping
over-and-over between two specified frequency limits. This process is known as
SEARCHING, as the title implies, it can take a long time to find transmissions due
to their ‘often intermittent’ and brief nature. For this reason it is best to slice large
frequency ranges into smaller, more manageable pieces where they may be
intensively studied.
When examining large frequency bands, it is common to find that 90% of
frequencies are inactive and only a small number of the remaining constitute what
you really want. Searching still remains the best way to initially locate active and
interesting transmissions (in conjunction with a good frequency listing and band
plan).
SCAN: Once active transmission have been identified (either by searching or by

using a good frequency guide), it is more efficient to store the data into memories
which can be rapidly and automatically monitored in succession, stopping when
activity is encountered. This forms a much more efficient means of monitoring the
most wanted frequencies as you have targeted 100% what you most want to hear,
by contrast searching is very inefficient for day-to-day monitoring.
Note: It is very important that the squelch is advanced to cancel background

noise for the search & scan functions to operate. This is because the
AR-ONE believes that it has found an active frequency when the squelch
opens and “S” ‘squelch open’ icon is displayed to the left of the signal meter.
Advance the squelch control clockwise until the background noise is just
cancelled, this is known as the threshold position. If the squelch control is
advanced too far, weaker signals may be missed.
No noise and no “S” icon displayed (with squelch advanced clockwise

passed threshold) = squelch closed.
Signal received or ‘noise’ emanating from speaker (squelch fully

counterclockwise, below threshold) with “S” icon displayed = squelch open.
7
1-4 Accessories supplied
The following items are provided in the carton box:
1 AR-ONE receiver
1 DC power cable
1 Operating manual
1-5 Controls & functions

Controls are located on the front with most connectors on the rear of the AR-ONE, a brief
identification is given here:
Front Panel
1. Volume control plus isolate power On/Off

2. Squelch control
3. Phones jack (3.5 mm mono or stereo may be used)
4. Escape key
5. Key Lock key
6. Monitor key
7. Function keys
8. LCD (Liquid Crystal Display)
9. Main keyboard (ten keys plus decimal and enter)
10. Main tuning dial (frequency change and menu manipulation)
11. Arrow keys (frequency change and menu manipulation)
8
Rear Panel
12. Antenna connector (N type)

13. Standard signal (10 MHz) input connector
14. IF output connector
15. Main power switch
16. DC power input connector (design may vary depending on AR-ONE
generation)
17. Remote control connector (RS-232C) -- 1
18. Remote control connector (RS-232C) –2
19. External audio output connector (when used, the internal speaker is disabled)
20. Audio output connector (speaker output without disabling the internal speaker)
21. Signal output connector (0 – 4.5 V DC maximum)
RS-232C connection requirements:

The REMOTE RS-232C connectors (17 & 18 above) are designed for connection directly to
a RS-232C serial port of a PC. By daisy chaining the units, control of up to 99 AR-ONE
receivers is possible from one PC. No interface is required, just a standard RS-232C straight
cable. Connections for a PC are as follows:
AR-ONE DB-9 RS-232C cable DB-25 RS-232C cable
Pin # 2 Pin # 2 Pin # 3
Pin # 3 Pin # 3 Pin # 2
Pin # 5 Pin # 5 (Ground) Pin # 7 (Ground)
Pin # 7 Pin # 7 Pin # 4
Pin # 8 Pin # 8 Pin # 5
9
1-5-1 Keypad
Keypad conventions
Most keys have secondary functions, these are printed on the panel. However, due to
the restrictions of available space, not all functions can be shown.
Secondary functions of the AR-ONE are indicated with white characters above
each key. To access the secondary function, push the FUNC key, and then push the
respective key.
1-5-2 Summary of keys
ESC
Cancels entry from the keypad.
LOCK
This key is intentionally small to reduce the chances of accidental operation. Key lock is
useful when you do not wish an important frequency to be lost or the AR-ONE to be
incorrectly set to a different frequency.
MON
To force the squelch open so that you may manually intervene to ensure that no weak
signals are missed.
FUNC
Selects the secondary functions of keypad.
SCAN
Initiates SCAN.
MEMO
Push the [FUNC] key, and then push this key to go into memory read mode.
SRCH (SEARCH)
Initiates SEARCH.
VFO
VFO mode selection. There are 10 VFOs (VFO-A through VFO-J).
STEP
Push the [FUNC] key, and then push this key to enable frequency step selection.
MODE
Receive mode selection.
WIDTH
Push the [FUNC] key, and then push this key to select the IF band width menu.
10
ATT
RF Attenuator. Move the cursor to select the desired parameter. The AUTO selection will
work best for most of cases.
AGC
Automatic Gain Control. Move the cursor to select the desired AGC time constant. Usually,
FAST is used to receive CW, MEDIUM for AM and FM, and SLOW for SSB. When MANU is
selected, any desired parameter (between 0 – 255) can be selected for manual gain control.
dBm
Toggles the incoming signal strength unit between dBm, dBuV, or ordinary S units.
0~9,.
Numeric keys.
S. SET
Push the [FUNC] key, and then push this key to select the desired memory channels to scan
in the SELECT SCAN mode.
S.SCAN
Push the [FUNC] key, and then push this key to initiate SELECT SCAN.
DEL
Push the [FUNC] key, and then push this key to delete memory channels, a search bank or
pass frequency.
PRIO
Push the [FUNC] key, and then push this key to initiate PRIORITY CHANNEL RECEIVE.
RF AMP
Push the [FUNC] key, and then push this key to activate/deactivate the RF amplifier
(ON/OFF/AUTO).
S PROG
Push the [FUNC] key, and then push this key to set the search bank.
CONF
Push the [FUNC] key, and then push this key to access CONFIGURATION menu to alter
beep level setting, backlight function, etc.
SQL
Push the [FUNC] key, and then push this key to select either the noise squelch mode or
level squelch mode.
PASS
Push the [FUNC] key, and then push this key to set pass frequencies in search mode.
11
OFFSET
Push the [FUNC] key, and then push this key to activate/deactivate the frequency offset in
duplex mode.
AFC
Push the [FUNC] key, and then push this key to activate/deactivate the AFC (Automatic
Frequency Control) function.
ENT
To validate data entry.
M. in
In the manual receive mode or search mode, push the [FUNC] key, and then push this key
to enter the frequency into memory.
1-6 Computer control
Connect the AR-ONE to the serial port of a computer using an RS-232C serial cable
terminated in a 9-pin male connector. The RS-232C parameters may be defined using the
CONFIG menu. Baud rates (transfer speed) can be set to 9600, 19200 (default) or 38400
bps. Since there are two independent RS-232C ports with the AR-ONE, it is possible to set
an ‘address’ to facilitate connection of up to 99 AR-ONE receivers to a single PC.
The RS-232C parameters are as follows:

Baud Rate: 9600, 19200 (default) or 38400 bps
De-limiter: CR, LF
Data bit: 8 bit
Stop bit: 2 bit
Parity: None
X flow: None
Please refer to chapter 7 for further details.
1-7 IF output and Spectrum Display Unit (SDU5600 )

The rear panel has a 10.7 MHz IF output designed to drive the optional SDU5600 Spectrum
Display Unit. The SDU5600 provides an excellent tool for locating elusive transmissions with
a PEAK capability to ‘freeze’ the briefest of transmissions for later measurement of
frequency and level after the event.
(Note: The IF output frequency is selectable in the CONFIG menu, 10.7 MHz or 455 kHz).
12
2 Getting started
2-1 Making the AR-ONE ready for operation
2-1-1 LCD (Liquid Crystal Display)
All relevant operational information is provided via the LCD. The LCD contrast is adjustable.
2-1-2 Connect the antenna

For reception on all bands, connect the antenna to the N connector on the rear panel of
the AR-ONE. Refer to chapter 10 for an overview of the available AOR antennas depending
on your target frequency range.
2-1-3 Connect power
Connect power to the DC power jack on the rear panel of the AR-ONE. For optimal
performance use a regulated DC power supply (12 ~ 14 V with capacity 2A).
Do not connect to a 24 V system.
(DC power socket design may vary depending on AR-ONE generation)
2-2 Switching on for the first time

Set the squelch control to the ‘mid point’. Turn the power switch on the rear panel of the
AR-ONE. This is a main power switch. The green LED on the switch will illuminate. Then
rotate the PWR/VOL control to the ‘mid point’, as you start to rotate the PWR/VOL control, a
‘click’ will be heard as the power isolation switch contact switches on. Please be careful NOT
to switch on any receiver with an earphone connected, there may be an audible click when
the unit is switched on or the volume may be accidentally set too high.
13
The AR-ONE will take approximately 4 - 5 seconds before information appears on the
LCD. This is normal, while the AR-ONE microprocessor generates the ‘boot up data’
required to control the receiver.
2-3 Squelch Circuit

In normal use, NOISE SQUELCH is used. However, LEVEL SQUELCH can be selected for
search and scan operations. The LEVEL SQUELCH parameter causes the AR-ONE to
check the signal strength of active frequencies and to only stop when the signal strength is
above a preset level (which is programmable).
To select LEVEL SQUELCH, perform the following steps:
1. Push the FUNC key.

2. Push the “8” key.
14
3. On the bottom of the LCD, a bar will be displayed. Using the SQL control,
adjust the desired signal level.
4. Push the ENT key to confirm entry.
5. Squelch will open only when the input signal strength is above this set level.
6. To select NOISE SQUELCH, repeat above steps.
2-4 VFO selection

The AR-ONE has ten (10) VFOs being identified as “V-A” through “V-J” on the top left of the
LCD. The term VFO historically means ‘Variable Frequency Oscillator’ and today refers to
a tunable data store which contains frequency, step, step-adjust, attenuator etc. Pushing
the VFO key each time will select the one VFO out of 10. The AR-ONE has an AUTOMODE
setting, and therefore, in most cases a proper receive mode and frequency step are
automatically selected.
2-4-1 Tuning frequency

2-4-1-1 Entering a frequency using the numeric keypad
While in VFO mode, enter the required frequency using MHz format followed by the ENT
key.
Example of frequency entry of 80.8 MHz:
Push the [8] key. Push the [0] key. Push the [.] key. Push the [8] key. Push the
[ENT] key.
Example of frequency entry of 954 kHz (0.954 MHz)
Push the [.] key. Push the [9] key. Push the [5] key. Push the [4] key. Push the
[ENT] key.
Aborting frequency input

If for some reason you do not wish to complete the frequency data input, push the ESC key
before completing the input sequence with the ENT key.
15
2-4-1-2 Changing frequency using the main tuning dial
While in VFO mode, the active VFO frequency may be ‘tuned’ using the rotary main tuning
dial which is mounted on the right side of the front panel. You may rotate the dial ‘clockwise’
to increase frequency or turn ‘counterclockwise’ to decrease frequency.
2-4-1-3 Changing frequency using UP arrow key or DOWN arrow key

The UP arrow key and DOWN arrow key provide a convenient method of frequency change.
The speed at which the receiver steps up or down depends upon the STEP SIZE which is
default to AUTO. In AUTO the step size, receiver mode etc. is taken from the factory
pre-programmed band plan but may be overridden at any time.
Push the UP arrow key to tune the receiver upward in whichever step size is selected, use
the DOWN arrow key to tune the receiver downward in frequency.
2-5 Changing receive mode

Due to the necessities of signal bandwidth, channel occupancy and transmission efficiency,
different receive modes are used by various services. Specifications being not consistent
throughout the world, it is sometimes necessary to change receive mode in order to monitor
various transmissions.
For your convenience, receive mode and tuning step size have been pre-programmed into
the AR-ONE auto-mode band plan data at the factory to simplify operation of the receiver,
especially while you familiarize yourself with all functions. Should you wish, the defaults may
be manually overridden at anytime so that you may select an alternative receive mode and
tuning step on any frequency.
AM
Amplitude Modulation – Used by broadcast services throughout the world on long wave,
medium wave and shortwave. AM is also used by VHF airband, UHF military airband and
some PMR (Private Mobile Radio) and utility services.
FM
There are two common types of FM (Frequency Modulation), these are:
NFM – Narrow Band Frequency Modulation – this provides high quality communication for
relatively short distance operation. FM uses a greater frequency bandwidth than other
modes such as SSB, so is less efficient.
NFM is the most common mode used above 30 MHz with the exception of the airbands.
NFM is widely used on the VHF bands: VHF marine band, 2m amateur band, 70 cm
amateur band, PMR (Private Mobile Radio) and utilities.
16
In the absence of signal, the background white noise may appear quite loud. For ease of
listening, the squelch control should be rotated clockwise until he background noise just
disappears, this should be carried out while no signal is present. The point where the
background noise is cancelled is known as threshold point. Do not advance the squelch
control more than necessary or the receiver will appear to be desensitized and weaker
signals will be missed.
WFM – Wide Band Frequency Modulation – used by VHF and UHF broadcast stations as
excellent audio quality is available due to the relatively wide frequency bandwidth employed.
Used only for local services such as VHF band stereo (received as mono on the AR-ONE)
and UHF TV sound channels.
LSB – Lower Side Band – is form of SSB (Single Side Band). LSB tends not to be used
commercially but is extensively used by Radio Amateurs on frequencies below 10 MHz.
This assists the separation of Commercial and Amateur users on traditionally shared bands
and prevents them from speaking to each other.
SSB is a very efficient method of transmission as the unwanted second sideband and carrier
have been removed. This allows the full transmitter power to be employed in carrying
useful information within the wanted sideband. As a result, greater distances are possible on
SSB and a smaller frequency bandwidth is required than most other modes.
USB – Upper Side Band – The same comments apply as for LSB. By convention, Radio
Amateurs also use USB above 10 MHz.
CW - Continuous Wave – Often referred as Carrier Wave or Morse Code. Commonly used
on the shortwave bands by radio amateurs toward the lower end of each band allocation.
Some commercial use is still made by shipping etc although its use is being phased out due
to the introduction of automated stations.
2-5-1 Auto-mode selection

When auto-mode is in operation, receive mode and tuning step size are automatically
selected for you.
To activate auto-mode or reconfirm its selection while in VFO mode,
Push and hold the MODE key for more than 2 seconds.
The AUT icon appears on the top right portion of the LCD.
17
Note: Auto-mode is cancelled as soon as the receive mode, tuning step or other related data
is changed. Remember that auto-STEP and auto-MODE are linked, reselect AUTO-MODE
if either have been adjusted and you require the auto band plan selection.
2-5-2 Receive mode selection

Any receive mode may be selected at any frequency within the receiver’s frequency
coverage. To access the receive mode menu, push MODE. The following modes are
available: AUTO, WFM, NFM, USB, LSB, CW. Use the main tuning dial or arrow key to
make the selection. To accept the selection, push the ENT key.
2-6 Changing tuning STEP size

Each country’s government decides upon the specification for channel occupancy, step
(separation) and mode.
Not surprisingly the allocation of frequency bands are not the same all over the world and
channel separation (step) varies from band to band. As an example, the channel separation
(step) for the MW (medium wave) band in the U.S.A. is 10 kHz while in Europe and Japan
it is 9 kHz.
For the above reasons it is necessary to sometimes alter the STEP size according to local
band plan conventions. The pre-programming of step size may be manually over-ridden so
you may choose alternative settings at will.
Should you wish to change the default tuning step size, push the FUNC key and then push
the VFO key.
The third row of the LCD will display the current default size.
18
The bottom line of the LCD displays the icon “STEP SET” to indicate that the AR-ONE is
Waiting for you to change the step size.
Use the main tuning dial or arrow key to select the desired step size. To accept the displayed
tuning step size, push the ENT key.
The tuning step size can be programmed in 1 Hz increments (via the keypad) so unusual
step sizes are possible.
The acceptable step size range is less than 1 MHz in 1 Hz steps.
2-7 IF Bandwidth
The IF bandwidth determines how SELECTIVE the receiver will be when monitoring signals
off air. However, it is not simply a case of using the narrowest filter at all times, particular
modes require differing amounts of bandwidth in order to operate, otherwise the receive
system simply will not produce intelligible sound. Correct receive mode and IF bandwidth
must always be selected for optimum reception. If the bandwidth selection is too narrow,
distortion or signal break-up may occur. If the bandwidth selection is too wide, adjacent
interference may be encountered. For this reason, a selection of IF filter bandwidths are
fitted as standard.
Typical examples of receive mode and IF bandwidth are:
300 KHz -- VHF FM broadcast (220 KHz may be also be used – mono only).
200 KHz -- VHF FM broadcast (110 KHz may be also be used – mono only).
100 KHz or 30 KHz – Wireless mic, etc. (30 KHz for satellite FAX, too).
16 KHz – PMR, amateur band, etc. FM 6 KHz may also be used.
8.5 KHz or 6 KHz – VHF/UHF airband, shortwave, medium & long wave, PMR, etc.
3 KHz – Short wave amateur band, short wave utility such as oceanic airband etc.
0.5 KHz – Morse code used by radio amateurs and some marine traffic on shortwave.
19
An appropriate IF filter is automatically selected when auto mode is engaged. However any
combination of IF filter and receive mode is possible in manual mode. When you have
manually selected an IF filter bandwidth, auto mode will be disengaged, but the receive
mode, step size, etc will be retained until they are changed manually.
2-7-1 Manually selecting IF bandwidth

Push the FUNC key, and then push the MODE key.
Select a new bandwidth from the list of 300, 200, 100, 30, 16, 8.5, 6, 3, and 0.5 KHz by
rotating the main tuning dial or arrow key. To accept the new bandwidth selection, push the
ENT key.
2-8 AGC (Automatic Gain Control)

To change the AGC parameter setting, push the FUNC key and then push the ATT key.
Select a new AGC parameter from the list of MANU, FAST, MID, SLOW by rotating the
main tuning dial or arrow key. To accept the new AGC parameter, push the ENT key.
20
When MANU is selected, a desired parameter can be entered between 0 ~ 255 in the
Configuration Menu.
2-9 ATTENUATOR
Activating the attenuator reduces signals to the RF input stages of the AR-ONE to prevent
overloading, for example when the receiver is used in close proximity to strong
transmissions.
The AR-ONE has four settings for ATT (attenuator), 0 dB, 10dB, 20 dB, and AUTO.
To change the ATT parameter setting, push the ATT key.
Select a new ATT parameter from the list by rotating the main tuning dial or arrow key. To
accept the new ATT parameter, push the ENT key.
When ATT is set to OFF, the ‘t0’ icon will display on the top right of the LCD.
When ATT is set to 10 dB, the ‘t1’ icon will display on top right of the LCD.
When ATT is set to 20 dB, the ‘t2’ icon will display on top right of the LCD.
21
2-10 RF AMPLIFIER
The AR-ONE features a preamplifier. The LCD icon “a” is used to display the setting in use.
To change the RF Amplifier setting, push the FUNC key and then push the 5 key.
Select a new AMP parameter from the list of ON, OFF, AUTO by rotating the main tuning
dial or arrow key. To accept the new AMP parameter, push the ENT key.
22
2-11 OFFSET
This function enables the receive frequency to be quickly SHIFTED by a predetermined
value, this makes it easy to track duplex-transmissions or check repeater inputs/outputs.
The locations for frequency offset storage are numbered 00 to 47 with 00 acting as OFF, this
makes 47 locations available.
Frequency offset may be programmed into VFO, memory channel and search banks. It is
most convenient to set-up in VFO mode then save the data to specific memory channels
for quick recall at a later date. Frequency offset is primarily designed for memory channel
use, it may appear rather long winded to toggle on/off in VFO mode. However even when
programmed, frequency offset is in no way detrimental to normal operation.
The acceptable range of frequency offset is 0 MHz to 999.999 MHz, of course if the offset is
set to 0 MHz, the frequency will not change! Before the FREQUENCY OFFSET function can
be used, it first needs to be configured.
2-11-1 Using pre-programmed frequency offset data

To access the frequency offset set-up menu, push the FUNC key, and then push the .
(decimal) key.
The third line will display DUPLEX followed by the current offset channel number.
Use the main tuning dial or arrow keys to review the offset locations. The shift direction
can be changed by pushing the FUNC key. To accept the offset setting, push the ENT key.
2-11-2 Entering new frequency offset data

Assume that you are in VFO mode.
To access the frequency offset set-up menu, perform the following steps:
1. Push the FUNC key, and then push the . (decimal) key. The third line will display
23
DUPLEX followed by the current offset channel number.
Use the main tuning dial or arrow keys to review the offset locations.
2. Push down arrow key. The cursor will move down to the bottom line of the LCD.
3. Enter the desired offset in MHz format. The shift direction can be changed by pushing
the FUNC key.
4. To accept the offset setting, push the ENT key.
3 Memory channels & banks

It is convenient to store commonly used frequencies into a memory channel along with
mode etc, this saves having to key the data in over and over again. Memory read is very
straightforward and quick when compared to retyping all data.
3-1 Memory channel overview

Think of memory channels as pages in a notebook, each of which is numbered to identify it.
Data may be written to each new page (memory channel) and each page may be
overwritten with new data, they can be used over and over again. The AR-ONE has 1,000
memory channels and one priority channel.
Each memory channel may hold:

One receive frequency
Receive mode
Tuning step
Frequency offset
Attenuator setting
Text comment of up to 12 characters
The alphanumeric comment may be used to ease identification at a later date and to provide
text search function. The 1,000 memory channels are divided into 10 banks, each having
24
100 channels. The memory banks are identified by the first BANK number 0, 1, 2, 3, 4, 5, 6.
7, 8 and 9 and the individual channels are numbered from 00 to 99.
Examples are “000” for the first channel location in memory bank “0” and “099” for the last
memory channel in memory bank “0”.
“415” is the location: memory bank “4” channel “15”.
The data contents of memory and search banks are held in a EEPROM so that no backup
battery is required for memory retention.
The stored data may be quickly and easily recalled, changed or deleted using the memory
recall and delete functions.
Note: When the receiver is switched OFF, all VFO data will be automatically stored into
EEPROM memory storage.
3-2 Storing VFO frequencies & data into memory

The process to save a displayed VFO frequency to memory is as follows:
a) In VFO mode, select the required frequency, mode, attenuator etc.
b) Push the FUNC key, and then push the ENT key to go to the memory write screen.
c) Use the keypad, main tuning dial or arrow keys to select the desired memory location
(BANK and CHANNEL).
d) Add a text comment (optional) or delete an existing comment.
e) Push the ENT key to exit the menu and save the data to the specified memory
location.
Let’s assume that you are going to store the frequency of 123.500 MHz into memory bank
“3” location “25” (325) while in VFO mode with the text comment of “AIRBAND”.
If a mistake is made during programming, push the ESC key to abort entry and return to
VFO mode.
1) Start by selecting VFO mode then key in the frequency of 123.500 MHz, “mode and step
25
size” are set to the default auto mode.
Push the VFO key to set the AR-ONE into VFO mode.
Push the 1 key.
Push the 2 key.
Push the 3 key.
Push the . (decimal) key.
Push the 5 key.
Push the ENT key.
2) Then push the FUNC key, and then push the ENT key to enter “memory input” mode.
Using the main tuning dial or arrow keys, enter 325 to store the frequency into the
location (memory bank 3, channel number 25).
3) Push the down arrow key to add the text comment “AIRBAND”.
Use the main tuning dial to select the text and the arrow keys to move position of text
input. A maximum of 12 characters may be added to each memory channel, it is
recommended that a minimum of three be used for efficient use of the text search
function (a minimum of 2 characters are required for text search).
To erase a character press the S SET key, to erase an entire text comment, place the
cursor on the first character and push the FUNC key. Push the ENT key to complete.
3-3 Memory read “M.RD”

Once frequency and mode data has been stored into a memory location, its retrieval is quick
and simple. Let’s assume that you are going to retrieve the frequency of 123.500 MHz which
has been programmed into memory “325” during an earlier example in the preceding
section.
Push the FUNC key and push the SCAN key to go into memory read mode, the “M.RD”
icon appears on the top left of the LCD to confirm operation. The AR-ONE will monitor
26
whatever memory channel you enter.
The AR-ONE will display memory channel, mode, text comment (if one was used). The
memory channel last used (for memory write or recall) will initially be displayed. If the
desired memory channel is not immediately displayed, it may be recalled by keying in the
required three digit location.
To recall memory channel “325”, push either the right arrow key or left arrow key to select “3”
as the memory bank. Rotate the main tuning dial or push either the up arrow key or down
arrow key to select “25”.
3-4 Deleting memory channels

It is possible to over-write a memory channel with new data or delete the channel entirely.
Push the FUNC key, and then push the 3 key to enter the “MEM DELETE” menu.
27
Push either the right arrow key or left arrow key to select the desired memory bank.
Rotate the main tuning dial or push either the up arrow key or down arrow key to select
the desired memory channel to delete.
Push the ENT key to delete it or push ESC to abort.
4 SCAN – scanning memory channels

In the SCAN mode the contents stored in the memory channels are automatically recalled
and scanned very quickly for activity.
*** It is important that you do not confuse SCAN and SEARCH modes. ***
SEARCH mode (covered later in this manual) automatically TUNES THE RECEIVER
THROUGH ALL FREQUENCIES between two specified frequency limits looking for active
frequencies.
4-1 SCAN – outline introduction

During SCAN, the AR-ONE automatically recalls memory channels which contains data in
numeric order and monitors them looking for activity. When an ‘active’ memory channel is
located (when a signal is found and the squelch is open), the AR-ONE will temporarily stop
scanning.
4-2 Starting SCAN

Presuming that some memory channels are programmed with data, start the scan
process with one push of the SCAN key.
The icon “HYPER SCAN” is displayed on the LCD to indicate that the SCAN process has
been started, a bank number will be also be displayed representing the current bank.
Ensure that the squelch is set to threshold point so that background noise is
cancelled and the squelch closes (otherwise scan will not operate).
28
When SCAN has been selected, only the currently displayed memory bank WHICH
CONTAINS DATA will be SCANNED, receive mode and frequency are unimportant. Any
memory channels which contain no data (empty) will be ignored (skipped).
4-3 Selecting a scan bank

The memory bank identifier (such as “3”) will be displayed on the middle right of the LCD.
If more than one memory channel is programmed into the current memory bank, and when
an ‘active’ channel has been located (busy, so the squelch opens), the scan process will
temporarily pause on the active channel, the memory location (such as “115”) will be
displayed along with any accompanying text (displayed underneath the memory location).
To select another memory bank for scanning, use the right arrow key or left arrow key.
If no data is available, the next bank with valid data will be recalled (empty memory banks
are skipped).
To exit from SCAN mode, push the VFO key.
4-4 Select scan

Select scan enables you to ‘tag’ memory channels to make a temporary list up to 50
channels in the same memory bank for scanning in a separate list called the SELECT SCAN
LIST.
4-4-1 Adding select scan channels in memory read
In memory read mode, push the FUNC key, and then push the 1 key to toggle the select
scan tag on/off, the icon “SEL” confirms selection.
4-4-2 Starting / stopping select scan

To start select scan, you must first have at least two memory channels tagged for select
scan.
29
Push the FUNC key, and then push the 2 key to start select scan. The direction of scan can
be reversed using the main tuning dial knob.
To stop select scan, push the VFO key.
5 Search mode
In search mode, the AR-ONE is programmed to automatically tune between two specified
frequency limits looking for activity. Please refer to section 1-3 of this manual if you do not
fully understand the function of SEARCH.
5-1 Search type

The AR-ONE is equipped with PROGRAM SEARCH.
PROGRAM SEARCH = search between user preprogrammed limits
5-1-1 Program search overview
There are 40 program search banks (referred to simply as search banks), which can be
programmed with specific parameters:
30
LO (lower) start frequency
HI (upper) stop frequency
Receive mode (or set to AUTO MODE)
Step (if auto is not selected)
Text comment
The program search banks are identified by numbers (01 ~ 40). To help with identification,
each bank may be labeled with an alphanumeric text comment.
5-2 Staring program search

Presuming that data is already stored into a search bank …
Push the SRCH key to start the program search process.
The LCD icon “SRCH” will be displayed and as long as the squelch is closed, the search
process will start from the lower frequency limit and will progress toward the upper
frequency limit. When the program limit is reached, the search loops around and starts the
process again.
Note: If no search banks have been programmed, the search will not operate.
5-2-1 Reversing the direction of search

To reverse the direction of search, use the main tuning dial or the up/down arrow keys. This
is useful to enable you to search back over an interesting point of the search process.
31
5-2-2 Forcing the search to resume
If the AR-ONE stops on an unwanted busy frequency, rotate the main tuning dial knob or
use the up arrow key or down arrow key to force the search process to resume from the
current frequency displayed.
5-2-3 Stopping the search
While the search process is in progress (not stopped), push the VFO key (displaying the
data on screen before search was started).
5-3 Selection of search bank

There are 40 search banks. While searching, use the right arrow key or left arrow key to step
through search banks which contain data. If no data is programmed in the nominated search
bank, the next bank containing valid data will be used.
5-4 Programming a search bank

Each of the 40 search banks may be programmed with different frequency limits, receive
modes, etc.
Push the FUNC key, and then push the 6 key to access the “SRCH PROG” menu.
32
Use the main tuning dial, right arrow key, left arrow key or keypad to select the bank you
wish to program or overwrite (The down arrow key is used to move through the menu).
Push the down arrow key.
33
LO: Input the lower start frequency in MHz format (don’t push the ENT key).
HI: Input the higher end (stop) frequency in MHz format (don’t push the ENT key).
34
MODE SET: Use the right arrow key or left arrow key or main tuning dial to select receive
mode, the FUNC key is used as a short cut to “AUTO”.
Note: If the receive mode is set to “AUTO”, the receive mode, channel step will be
taken from the pre-programmed auto band plan data, for this reason the
detailing will not be required and skipped. The next menu will be TEXT INPUT.
STEP: Assuming that a receive mode other than “AUTO” was selected, you will be
presented with the “STEP SET” menu. Use the main tuning dial or the right arrow key or left
arrow key to select the required tuning step from the following:
0.001 (1 Hz), 0.010 (10 Hz), 0.500 (500 Hz), 1.000 kHz, 2.000 kHz, 5.000 kHz, 5.25 kHz,
9.000 kHz, 10.000 kHz, 12.5 kHz, 25.000 kHz, 50.000 kHz, 100.000 kHz.
Alternatively, a step size may be entered in kHz format via the keypad in multiples of 1Hz in
the range of 1Hz ~ 100.000 kHz (do not push enter).
Push the down arrow key to access the TEXT INPUT menu.
TXT (TEXT): The cursor will be positioned in the bottom of the LCD. If an unwanted text
comment exists, push the S SET key to delete the character highlighted. To delete the entire
comment, place the cursor on the first character and push the FUNC key. Add new text as
required.
35
To accept the data input, push the ENT key.
5-5 Deleting search banks

A delete menu is provided so that you can delete program search data (of course you may
simply overwrite the data, too) .
While in search mode, the DELETE menu is accessed as follows:
Push the FUNC key and then push the 3 key.
36
Using the main tuning dial, keypad, right arrow key or left arrow key, select the desired
search bank.
The “HI” and “LO” frequency limits will appear on the LCD along with any associated text
comment to aid the identification of the required search bank.
To delete the program search bank, push the ENT key.
5-6 Locking out unwanted active frequencies (PASS)

It is possible to lock out (PASS) unwanted frequencies while in program search mode.
This is useful to eliminate unwanted permanent transmissions. It is important to understand
37
the PASS function before taking action or transmissions may be missed.
While stopped on an unwanted frequency, push FUNC and then push the 9 key.
The search process will resume. It will appear that all frequencies are still searched,
however, locked out frequencies will be ‘passed over’, the search will not stop on locked out
frequencies.
5-6-1 Deleting pass channels

If you are currently in search mode, push the FUNC key and then push the 3 key.
This will access the MEMORY CHANNEL DELETE MENU.
38
If pass channels have already been tagged for the current search bank, the icon “PAS”
(PASS) will be displayed on the LCD.
Push the FUNC key to delete the pass frequency.
To exit from this menu, push the ENT key.
6 Configuration menu
The configuration menu is used to set fundamental operating parameters and other
variables which do not appear in any other menu heading.
BEEP Confirmation & error tone
LAMP LCD & keypad illumination
DIMM Backlit illumination dimmer
CONTRAST LCD contrast adjustment
OPENING MESSAGE Change the power-up message
AGC AGC (Automatic Gain Control) adjustment
IF-GAIN IF Gain control adjustment
RF-GAIN RF Gain control adjustment
39
BPS Communication data speed setting
RMT-ID RS-232C identification address setting
DELAY Scan/Search delay setting
FREE Scan/Search free setting
SPEAKER Speaker/headphones setting
HPF/LPF Audio Filter setting
DE-Emphasis De-emphasis setting
PRIO-CH Priority channel setting
Item Parameter Default

BEEP OFF/ 01 – 09 6
LAMP AUTO/ON/OFF ON
DIMM ON/OFF OFF
CONTRAST 00 – 32 12
OPENING MSG NORM/QUICK/USER NORM
MANUAL AGC 0 – 255 255
IF-GAIN 0 – 255 255
RF-GAIN 0 – 255 255
BPS 9600, 19200 or 38400 19200
RMT-ID 00 – 99 0
DELAY 00 – 99 0
FREE OFF/0.1 – 9.9 OFF
SPEAKER ON/OFF ON
(REAR)
(FRONT) ON/OFF ON
(PHONES) ON/OFF ON
HPF AUTO/50/200/300/400Hz AUTO
LPF AUTO/3K/4K/6K/12K AUTO
De-Emphasis μS/75μ
Auto/THRU/25μ μS/750μ
μS AUTO
6-1 Configure beep

The AR-ONE emits confirmation ‘beeps’ while the keypad is used. A ‘HIGH’ pitched beep
indicates correct operation while a ‘LOW’ pitched beep indicates that an error or unexpected
entry has taken place. The volume of the beep is independent of the main volume control
and can be separately defined. It is recommended that the beep function be enabled,
40
especially in the early days while gaining familiarity of the receiver.
To access the configuration menu, push the FUNC key and then push the 7 key.
The first item in the configuration menu is “BEEP”, the default is beep on with a volume
level of 06. Use the main tuning dial, the right arrow key or the left arrow key to change the
beep level between the range of OFF and 01 to 09 (09 being the loudest).
Push the ENT key to accept the data and return to a standard display.
Alternatively, push the ESC key to abort entry, or, push the down arrow key to move to the
next item on the configuration menu (LAMP).
6-2 Configure lamp

The AR-ONE is equipped with high intensity green LEDs to illuminate the LCD and keypad
when operating in areas of low level lighting.
The lamp may be configured in three ways:
AUTO: The lamp will automatically illuminate when the keypad or main tuning dial are
used. The lamp will remain illuminated for a further five second after the last key push and
then switch off. The lamp will also automatically illuminate while the squelch opens.
ON: This is default setting. The lamp will continuously illuminate the LCD and keypad.
OFF: The lamp remains permanently extinguished, this is useful when used in areas of
high light levels.
41
Push the down arrow key to move the cursor to the “LAMP” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to toggle the lamp
between AUTO, ON and OFF.
Push the ENT key to accept the data and return to a standard display. Alternatively, push the
ESC key to abort entry, or, push the down arrow key to move to the next item on the
configuration menu (DIMM).
6-3 Configure dimmer

A DIMM (dimmer) function is available to dim the intensity of the LEDs. This function is
useful when used in areas of high light levels.
The default setting of DIMM is “OFF”.
Push the down arrow key to move the cursor to the “DIMM” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to toggle the dimmer
between ON and OFF.
Push the ENT key to accept the data and return to a standard display.
Alternatively, push the ESC key to abort entry, or, push the down arrow key to move to the
next item on the configuration menu (CONTRAST).
6-4 Configure contrast

The AR-ONE is equipped with variable LCD contrast which is adjustable in 32 steps to
provide best visibility under different viewing angles, extremes of ambient light &
temperature (and between sets due to variation).
The default setting for contrast is 12. The display generally becomes too dark to read around
20 and too feint around 02. Best results are usually achieved within the range of 09 – 15.
Push the down arrow key to move the cursor to the “CONTRAST” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to vary the contrast level
to achieve best visibility.
configuration menu (OPENING MESSAGE).
6-5 Configure Manual AGC

The manual AGC function is to adjust the receiver’s AGC (Automatic Gain Control) when it
42
is set OFF.
The default setting for Manual AGC is 255, maximum gain control value. The value can be
adjusted according to the receiving condition.
Push the down arrow key to move the cursor to the “MANU AGC” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to vary the manual AGC
level for best reception.
configuration menu (IF-GAIN).
6-6 Configure IF-GAIN (Intermediate Frequency gain)

The IF gain control reduces the amplification in the receiver’s IF circuits and has the effect of
reducing the sensitivity of the receiver. Normally, this is performed by the AGC system, and
the control is left at maximum gain, but reducing the gain can be useful to limit noise when
listening to CW or SSB signals. The IF gain control must be used if the AGC is turned off.
The default setting for IF-GAIN is 255 (maximum gain control value).
Push the down arrow key to move the cursor to the “IF-GAIN” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to vary the IF-Gain
43
configuration menu (RF-GAIN).
6-7 Configure RF-GAIN (Radio Frequency gain)

The RF gain setting switches in the attenuator or preamplifier to suite the band conditions
and antenna in use.
The default setting for RF-GAIN is 255 (maximum gain control value). The value can be
adjusted according to the receiving conditions.
Push the down arrow key to move the cursor to the “RF-GAIN” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to vary the RF-Gain
configuration menu (BPS).
6-8 Configure Remote BPS (Baud rate)

The Remote BPS Set menu is used to configure the RS-232C computer control settings as it
is important that they exactly match those of an associated computer connection or another
AR-ONE (connected via a male 9-pin to male 9-pin straight cable).
Push the down arrow key to move the cursor to the “BPS SET” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to select the desired
RS-232C baud rate between 9600, 19200 or 38400 bps. The default setting is 19200 bps.
44
configuration menu (RMT-ID).
6-9 Configure RMT-ID (Remote ID)

When multiple units are connected via remote connectors, each AR-ONE must be assigned
a different ID (address). The value is adjustable between 00 ~ 99. The default value is 00.
Important notice: It is extremely important to set the RMT-ID to 00 for normal operation
of the RS-232C connection.
Push the down arrow key to move the cursor to the “RMT-ID” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to change the AR-ONE’s
RS-232C identification address.
configuration menu (DELAY).
6-10 Configure DELAY (Scan delay and Search delay)

This parameter affects the time the AR-ONE will remain on an active frequency in scan or
search mode once the received signal has disappeared and the squelch has closed. This
is particularly useful for customizing how long the receiver will wait for a reply before
resuming scan or search. For example, passing communications back and forth
between a control tower / aircraft may take a few seconds. The limits are OFF / HOLD
and 0.1 to 0.9 seconds in 0.1 second increments. The default is 2.0 seconds.
Push the down arrow key to move the cursor to the “DELAY” selection point.
45
delay parameters.
2.0s The AR-ONE will wait the specified time after the squelch closes before
resuming scan or search.
HOLD The AR-ONE will stop indefinitely when an active frequency is located,
this is very useful when you don’t want to miss that once-in-a-lifetime
transmission!
OFF The AR-ONE will resume scan or search instantaneously when the
squelch closes.
configuration menu (FREE).
6-11 Configure FREE (Scan free and Search free)

The scan free and search free parameter determines how long the AR-ONE will remain on
active frequency before resuming scan or search even though the frequency is still active.
This is useful if you wish to gain a snap shot of activity without the AR-ONE being tied to a
busy frequency for long periods of time (such as when monitoring active commercial
repeaters etc). Scan free and search free time saves you having to manually intervene to
force the scan or search process to resume and saves the need to lockout memory
channels or search frequencies using the PASS function. The limits are OFF and 0.1 to 9.9
seconds. The default setting is OFF.
Push the down arrow key to move the cursor to the “FREE” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to select the desired free
parameters.
configuration menu (SPEAKER).
6-12 Configure SPEAKER

The AR-ONE is equipped with 2 separate speakers, one in the main receiver unit and one in
the control head (Note: This function is available only when an optional separation kit is
used) and a phones jack. Each speaker / head phones output can be configured under this
menu.
46
6-12-1 Configure rear speaker
Push the down arrow key to move the cursor to the “REAR SP” selection point. This menu is
to configure the rear speaker. Use the main tuning dial, the right arrow key or the left arrow
key to select the desired rear speaker setting (ON or OFF).
configuration menu (FRONT SP).
6-12-2 Configure front speaker

(Note: This function is available only when an optional separation kit is used)
Push the down arrow key to move the cursor to the “FRONT SP” selection point. This menu
is to configure the front speaker. Use the main tuning dial, the right arrow key or the left
arrow key to select the desired rear speaker setting (ON or OFF).
configuration menu (PHONES).
6-12-3 Configure head phones output

Push the down arrow key to move the cursor to the “PHONES” selection point. This menu is
to configure the headphones output. Use the main tuning dial, the right arrow key or the left
arrow key to select the desired head phones output setting (ON or OFF).
configuration menu (Audio Filter).
47
6-13 Configure audio filters (HPF / LPF)
An audio HPF (High Pass Filter) and a LPF (Low Pass Filter) are available.
6-13-1 Configure audio HPF (high pass filter)
The audio high pass filter is useful for limiting the audio bass response (allowing higher
tones to pass) improving intelligibility in certain circumstances (such as low frequency
whistles on AM, SSB & CW).
There are four available pass frequencies: 50Hz, 200Hz, 300Hz, and 400Hz.
The higher the frequency the more limited the audio bandwidth. For highest fidelity for
listening, select 50Hz. The filter selection can be set to auto mode to select the proper filter
setting automatically.
The default is AUTO.
Push the down arrow key to move the cursor to “HPF” selection point.
This menu is to configure the high pass filter.

Use the main tuning dial, the right arrow key or the left arrow key to select the desired high
pass filter setting (AUTO / 50Hz / 200Hz / 300 Hz or 400Hz).
configuration menu (LPF).
48
6-13-2 Configure audio LPF (low pass filter)
The audio low pass filter is useful to cut off high tones (allowing low tones to pass) to
improve intelligibility of weak signals in close proximity to adjacent interference and to
remove hiss making listening for extended periods easier on the ears.
There are four available pass frequencies: 3KHz, 4KHz, 6KHz and 12KHz.
The lower the frequency the more limited the audio bandwidth. For highest fidelity for
listening, select 12.0KHz. The filter selection can be set to auto mode to select the proper
filter setting automatically. The default is AUTO.
Push the down arrow key to move the cursor to the “LPF” selection point.
This menu is to configure the low pass filter.
Use the main tuning dial, the right arrow key or the left arrow key to select the desired high
pass filter setting (AUTO / 3KHz / 4KHz / 6KHz or 12KHz).
configuration menu (De-Emphasis).
6-14 Configure Audio De-emphasis

This is really only applicable to FM mode and affects the sharpness of recovered audio.
The FM transmissions in different world areas have different defaults for de-emphasis.
For example, a value of 750 is selected in Europe, other settings may result in the recovered
audio sounding very muffled.
The available range is as follows: THRU, 25μS, 50μS, 75μS, and 750μS
The audio de-emphasis can be set to auto mode to select the proper setting automatically.
The default is AUTO.
Push the down arrow key to move the cursor to the “De-Emphasis” selection point.
This menu is to configure the audio de-emphasis.
de-emphasis setting (AUTO / THRU / 25uS / 50uS / 75uS or 750uS).
configuration menu (PRIO-CH).
6-15 Configure PRIO-CH (Priority Channel)

The priority function enables you to carry on scanning, searching or monitoring while the
49
AR-ONE checks a selected frequency for activity (taken from one of the 1,000 memory
channels periodically).
The priority checking is accomplished by momentarily tuning the receive circuit to the priority
frequency to see if it is active. If activity is found, the AR-ONE will remain on the active
frequency until the signal disappears. If no activity is detected, the receiver returns to the
VFO frequency, scan channel or search bank from where it originated.
The priority function has a large number of applications and is particularly useful for keeping
an eye on a distress frequency while scanning or searching another frequency band.
Note: Depending upon the frequency and mode stored as priority, an audible click may be
heard when the priority function is in operation. This is quite normal and is caused by the
internal switching of circuitry necessary to accomplish the frequency change (as two
frequencies cannot simultaneously be monitored).
6-15-1 Engaging Priority channel

Once engaged, the frequency is checked for activity periodically by the preset period that is
set by the configuration menu.
To engage the priority function, push the FUNC key and then push the 4 key.
Push the down arrow key to move the cursor to the “PRIO-CH” selection point.
This menu is to configure the priority channel.
priority channel. Push the downward key to select the time interval. Use the main tuning
dial, the right arrow key or the left arrow key to select the desired time interval for the priority
channel.
Push the ENT key to accept data and return to a standard display. Alternatively, push the
configuration menu (IF output).
50
6-16 Configure IF output frequency
The function enables you to tap the 2nd IF signal (10.7MHz) or the 3rd IF signal (455KHz)
from the BNC (marked as 10.7MHz) type connector on the rear panel. The 10.7MHz of the
2nd IF signal is to be used with the optional SDU5600 spectrum display unit for signal
analysis. The bandwidth at 10.7 MHz is +/- 5 MHz from the center frequency (10 MHz total).
6-16-1 Selecting IF output frequency

To select the IF frequency, push the FUNC key and then push the 7 key.
Push the down arrow key to move the cursor to the “IF out SEL” selection point.
Use the main tuning dial, the right arrow key or the left arrow key to select either 455kHz or
10.7 MHz.
Push the ENT key to validate. Alternatively, push the ESC key to abort entry. Or, push the
down arrow key to move to the next item on the configuration menu (Reference Signal).
6-17 Configure reference signal source

The function enables you to select the reference signal of the receiver. The AR-ONE has a
built-in stable reference oscillator, however, an external high stability 10 MHz reference
(such as off-air atomic coupled) can be accepted from the SMA connector (marked as 10
MHz IN) on the rear panel of the AR-ONE.
Push the down arrow key to move the cursor to the “REF SEL” selection point.
reference signal source (internal or external). The default is INT.
Push the ENT key to accept data and return to a standard display. Alternatively, push the
ESC key to abort entry.
51
7 Computer control
Connect the AR-ONE (any of the 2 serial sockets) to your computer’s serial port, using a
RS-232C cable terminated in a 9-pin plug.
The RS-232C parameters may be defined using the CONFIGURATION menu. Baud rates
(data transfer speed) may be set to 9600, 19200 or 38400 bps. 19200 bps is the factory
default. It is also possible to set an ‘address’ to facilitate connection of up to 99 AR-ONE
receivers to a single port for custom operation, the addresses may be set between the limits
of 01 to 99 with 00 representing single radio operation.
7-1 How to send an RS-232C command

Each command comprises of two upper case letters (header) along with operations as
required. All commands use ASCII code which MUST BE IN UPPER CASE (except for the
up arrow key, down arrow key, right arrow key, left arrow key and remote ID command (^A)
which are non-printable and use the control codes of ASCII). A terminal program such as
Windows Hyperterminal should be set as follows:
Baud rate 9600, 19200 or 38400 bps (this must match AR-ONE)
DATA BIT 8
STOP BIT 2
PARITY NONE
XFLOW NONE
Make sure that “local echo” is turned on. On Windows Hyperterminal you can access this
setting at: FILE > PROPERTIES > SETTINGS > ASCII SETUP. Check the box labeled
“Echo typed characters locally” and validate with OK.
7-2 Power on the AR-ONE

There are 2 switches to set ON:
-On the back of the receiver, labeled “MAIN”. The switch’s green LED should light.
-On the front panel’s “PWR/VOL” knob. Turn it slightly clockwise until you feel a click. The
receiver’s LCD and keys will light after about 4 seconds.
Now you can send any command from your PC’s Hyperterminal software.
All commands MUST BE IN UPPER CASE.
A multiple command entry is only valid where specified. Where a multiple command entry is
allowed, each command MUST be separated with a space “h20” (HEX DECIMAL). Each
command is completed and a [CR] or [CR][LF]. Although there is no local echo, either [CR]
52
or specified response should come back from the receiver after confirming the correct
command. If no response has been gained after a short while, the receiver has failed to
receive the command properly. Send a [CR] then re-send the command. Should problem
persist, check your connections and try reducing the RS-232C baud rate.
7-3 Detailed RS-232C command listing of the AR-ONE
X Power on x: any key to power on the AR-ONE (it takes 4 sec.)

QP Power off Power off
^Ann Remote ON Hex value 0x01
Accept a value nn in the range of 00-99 for remote
connection
EX Remote off Remote off
IDnn Remote ID To set: IDnn<CR>, nn: 00-99. To read:ID<CR>
RX MODE
Vx Select VFO To set: Vx<CR>, x:A – J (default :A)
MRmnn Memory mode m: 0 – 9 (memory bank), n: 00 – 99 (memory channel)
(default: 000)
MSm Memory scan mode m: 0 – 9 (memory bank), (default: 000)
SM Memory select mode
SSmm Search mode mm: 01 – 40 (search bank), (default: 01)
To read: RX <CR>
Response: Memory manual mode
MR MXmnn RFnnnnnnnnnn STnnnnnn Aun MDn BWn ATn AMn TMxxxxxxxx
Memory scan mode
MS MXmnn RFnnnnnnnnnn STnnnnnn Aun MDn BWn ATn Amn TMxxxxxxxx
Memory select mode
SM MXmnn RFnnnnnnnnnn STnnnnnn Aun MDn BWn Atn Amn TMxxxxxxxx
Search mode
SSmm RFnnnnnnnnnn STnnnnnn Aun MDn BWn Atn Amn TTxxxxxxxx
VFO mode
Vx RFnnnnnnnnnn STnnnnnn Aun MDn BWn Atn Amn (default: VFO-A)
53
FREQUENCY
RF RFnnnnnnnnnn (entry in Hz format) (VFO mode only)
RF RFnn.nn (entry in MHz format) (VFO mode only)
Vx Vx nnnnnnnnnn (entry in Hz format) x: A – J (VFO)
To read: RF <CR>
Response: RFnnnnnnnnnn (Hz)
STEP FREQUENCY
ST STnnnnnn (entry in Hz format) (not available in search mode)
ST STnn.nn (entry in kHz format) (not available in search mode)
ST STnn …nn (entry in kHz format) (not available in search mode)
To read: ST <CR>
Response: STnnnnnn (Hz)
AUTO MODE
AU AUn n: 0 Auto mode off
n: 1 Auto mode on
To read: AU <CR>
Response: AUn
OPERATION MODE
MD MDn (n: 0 - 6) Auto mode will be disabled by this command
n=0 FM (BW=16kHz,HPF=50Hz,LPF=3kHz,De-emphasis=750μS)
n=1 AM (BW=6kHz, HPF=50Hz, LPF=3kHz, De-emphasis=THRU)
n=2 CW (BW=0.5KHz, HPF=50Hz, LPF=3kHz, De-emphasis=THRU)
n=3 USB (BW=3kHz, HPF=50Hz, LPF=3kHz, De-emphasis=THRU)
n=4 LSB (BW=3kHz, HPF=50Hz, LPF=3kHz, De-emphasis=THRU)
n=5 WFM (BW=200kHz, HPF=50Hz, LPF=12kHz, De-emphasis=75μS)
n=6 NFM (BW=8.5kHz, HPF=50Hz, LPF=3kHz, De-emphasis=750μS)
To read: MD <CR>
Response: MDn
54
BANDWIDTH
BW BWn (n: 0 – 8) Auto mode will be disabled by this command
n=0 0.5kHz
n=1 3.0kHz
n=2 6.0kHz
n=3 8.5kHz
n=4 16kHz
n=5 30kHz
n=6 100kHz
n=7 200kHz
n=8 300kHz
To read: BW <CR>
Response: BWn
HPF (High Pass Filter)

HP HPn (n: 0 – 3 & F) Auto mode will be disabled by this command
n=0 50Hz
n=1 200Hz
n=2 300Hz
n=3 400Hz
n=F AUTO
To read: HP <CR>
Response: HPn
LPF (Low Pass Filter)

LP LPn (n: 0 – 3 & F) Auto mode will be disabled by this command
n=0 3KHz
n=1 4KHz
n=2 6KHz
n=3 12KHz
n=F AUTO
To read: LP <CR>
Response: LPn
55
AGC (Automatic Gain Control)
AC Acn (n: 0 – 2)
n=0 AGC - OFF
n=1 AGC - FAST
n=2 AGC - SLOW
n=3 AGC - MIDDLE
To read: AC <CR>
Response: ACn
DE-EMPHASIS
EN ENn (n: 0 – 5) Auto mode will be disabled by this command
n=0 25μS
n=1 50μS
n=2 75μS
n=3 750μS
n=4 THRU
n=5 AUTO
To read: EN <CR>
Response: ENn or Enmn (m=5, AUTO)
RF ATT (Attenuator)
AT ATn (n: 0 –3)
n=0 0dB
n=1 10dB
n=2 20dB
n=3 AUTO
To read: AT <CR>
Response: ATn
56
RF AMP (Amplifier)
AM AMn (n: 0 – 2)
n=0 RF AMP OFF
n=1 RF AMP ON
n=2 RF AMP AUTO
To read: AM <CR>
Response: AMn
BFO FREQ (Beat Frequency Oscillator Frequency)

BF BF +/-nnnn (nnnn: 0000 - +/- 3000Hz)
Available in CW, LSB, USB mode only
Default: CW +800Hz, USB +1500Hz, LSB -1500Hz
To read: BF <CR>
： BF +/-nnnn
Response：
N – SQ (Noise Squelch) THRESHOLD

RQ RQnnn (nnn: 000 – 255) Default: 000 (OFF)
To read: RQ <CR>
Response: RQ nnn
L – SQ (Level Squelch)
DB DBnnn (nnn: 000 – 255) Default: 000 (OFF)
To read: DB <CR>
Response: DB nnn
AF GAIN
AG Agnnn (nnn: 000 –255) Default: 255
Note: The volume control knob must be turned fully counterclockwise
To read: AG <CR>
Response: AG nnn
57
MANUAL GAIN (10.7 MHz AGC)
MG MGnnn (nnn: 000 – 255) Default: 255
Note: Available only when the AGC is set to OFF
To read: MG <CR>
Response: MG nnn
RF GAIN
RG RGnnn (nnn: 000 – 255) Default: 255
Note: The volume control knob must be turned fully
counterclockwise
To read: RG <CR>
Response: RG nnn
IF GAIN
IG IGnnn (nnn: 000 – 255) Default: 255
To read: IG <CR>
Response: IG nnn
SQUELCH SELECT
SQ SQn (n: 0 or 1) Default: 0 (noise squelch)
n=0 Noise Squelch mode
n=1 Level Squelch mode
To read: SQ <CR>
Response: SQn
SIGNAL LEVEL
LM To read: LM <CR>
Response NSQm LMnnn - When the noise squelch is selected
(nnn: 000 – 999)
LSQm LMnnn - When the level squelch is selected
(nnn: 000 – 999)
m: 1 When the squelch is closed

m: 0 When the squelch is opened
58
AUTO SIGNAL LEVEL
LC LCn
n:0 Auto Signal Level off
n:1 Auto Signal Level on
While n is set to 1, and the squelch opens, the signal level and frequency
information is sent to the PC
To read: LC <CR>
Response: LCn
SQm LMnnn RFnnnnnnnnnn
m: 0 Noise squelch mode
m: 1 Level squelch mode
nnn: signal level from 000 to 999
nnnnnnnnnn: frequency
AUTO BACKLIT
LA Lan (n: 0 - 2)
n: 0 LAMP OFF
n: 1 LAMP ON (Default)
n: 2 LAMP AUTO
(Will go off in 5 seconds after the squelch is closed)
To read: LA<CR>
Response: LAn
BACKLIT ON/OFF
BL BLn (n: 0 or 1) Available when LA is set to 2 (Auto).
n: 0 BACKLIT OFF
n: 1 BACKLIT ON (Default)
To read: BL<CR>
Response: BLn
59
BACKLIT DIMMER
LD LDn (n: 0 or 1)
n: 0 NORMAL (Default)
n: 1 DIMM
To read: LD<CR>
Response: LDn
LCD CONTRAST
LV LVnn (nn: 00 – 31) (Default: 12)
To read: LV<CR>
Response: LVnn
BEEP LEVEL
BV BVn (n: 0 – 9) (Default: 5)
To read: BV<CR>
Response: BVn
SPEAKER SELECT
SO SOn (n: 0 – 3) (Default: 3)
n: 0 FRONT OFF, REAR OFF

n: 1 REAR ON
n: 2 FRONT ON
n: 3 FRONT ON, REAR ON
To read: SO<CR>
Response: SOn
EXTERNAL SPEAKER
PO Pon (n: 0 or 1)
n: 0 OFF (Default)
n: 1 ON
To read: PO<CR>
Response: POn
60
DELAY TIME (SCAN DELAY AND SEARCH DELAY)
DD DDn.n (n.n: 0.0 – 9.9 second) Default: 2.0 sec.
nn: FF (hold)
To read: DD<CR>
Response: DDn.n or DDFF
FREE SCAN
SP SPn.n (n.n: 0.0 – 9.9 second)
n.n: 0.0 FREE SCAN OFF (Default)
n.n: 0.1 – 9.9 sec.
To read: SP<CR>
Response: SPn.n
SIGNAL METER DISPLAY

SF SFn (n: 0 – 2)
n: 0 ANALOG DISPLAY
n: 1 DIGITAL DISPLAY in dBμV (Default)
n: 2 DIGITAL DISPLAY in dBm
To read: SF<CR>
Response: SFn
DUPLEX MODE
OF Ofnnx (nn: 00 – 47) (00: OFF)
x: + or - (Offset direction)
To read: OF<CR>
Response: OF xnn
DUPLEX FREQUENCY
OL OLmm nnnnnnnn00 (mm: 01 - 19)
nnnn…n: Offset frequency (in 100Hz step, <1GHz)
To read: OL<CR>
Response: OLmm nnnnnnnnnn (10 digits)
61
SIGNAL LEVEL UNIT (in dBμV) – Read only
LU LU nnn (-nnn – nnn) dBμV
To read: LU<CR>
Response: LU nnn
SIGNAL LEVEL UNIT (in dBm) – Read only

LB LB nnn (-nnn – nnn) dBm
To read: LU<CR>
Response: LB nnn
SEARCH DATA SETTING – Write only

SE SEnn (nn: 01 – 40 ) Bank number
SLnnnnnnnnnn (Lower Frequency), SUnnnnnnnnnn (Upper Frequency), Aun,
STnnnnnn, MDn, BWn, ENn, ATn, AMn, ACn, TTxxxxxxxx (Enter text as needed)
Example: SE01, SL0124500000, SU0123900000, AU1, ST002500…

Note: Refer to individual command for details of each field.
SEARCH DATA LIST – Read only

SR SR Read search data of the current search bank
SRnn (nn: 01 – 40) Search data in search bank 1 - 40
SRn (n: 1 - 10) Search data in search bank 1- 10
SR% Search data in all search banks

SRn SLnnnnnnnnnn Sunnnnnnnnnn AUn MDn BWn ATn AMn TTxxxxxxxx
SRn --- (Blank)
PASS FREQUENCY – Write only

PW PW Register a current freq. to Pass freq.
PWnnnnnnnnnnnn Register the freq. to Pass freq.
62
PASS FREQUENCY LIST – Read only
PR PRnn (nn: 01 – 40) Bank number
PR00 nnnnnnnnnn
PR01 nnnnnnnnnn
PRmm (mm: 00 – 49) Last channel will be 49 or blank (- - -)
DELETE PASS FREQUENCY – Write only

PD PDmmnn (mm: 01 – 40) Bank number
(nn: 00 – 49) Pass channel
PDmm%% (mm: 01- 40) Bank number
Delete all pass frequencies on designated bank number
DELETE SEARCH DATA WITH PASS FREQUENCY – Write only

QS QSnn (nn: 01 – 40)
Delete search data and pass frequency on designated search bank
QS%%
Delete all search data and pass frequencies on all search banks
TRANSFER THE CURRENT SEARCH DATA TO VFO – Write only

SV SVn (n: 0 – 9)
n: 0 VFO – A
n: 1 VFO – B
n:9 VFO – J (Default)
MEMORY DATA SETTING – Write only

MX MX -- Write the current receiver data to the current bank and channel
MXmnn -- Write the current receiver data to the designated bank and channel
(m: 0 – 9) Bank number
(nn: 00 – 99) Memory channel
[Example]: MXmnn
RFnnnnnnnnnn (Frequency), Aun, STnnnnnn, MDn, BWn, ENn, ATn, AMn, ACn, Gan,
TMxxxxxxxx
63
MEMORY DATA LIST – Read only
MA MAn (n: 0 – 9) Bank number, memory data between CH00 to CH10.
MA Memory data for bank number higher than 10
[Example]: MXmnn MPn GAn RFnnnnnnnnnn AUn MDn BWn ATn AMn TMxxxxxxxx
SELECT MEMORY ON/OFF

GA GAn (n: 0 or 1) Memory select On/Off
n: 0 OFF
n: 1 ON
To read: GA<CR>
Response: GAn
SELECT MEMORY LIST – Read only

GR GRnn (nn: 00 – 99) Memory channel on the designated bank
GR%% All channels (100 channels maximum)
GRn (n: 0 – 9) List of 10 channels data
GR Next 10 channels data
[Example]: GRnn mxx … nn (nn: channel number, m: memory bank, xx: memory
channel)
DELETE MEMORY – Write only

MQn MQn (n:0 – 9) Bank number
MQ%% All banks
TRANSFER MEMORY DATA TO VFO – Write only

MV MVn (n: 0 – 9)
n: 0 VFO – A
n: 1 VFO – B
n: 8 VFO – I (Default)
n: 9 VFO – J
64
SCAN/SEARCH RE-START
SG SGn
n= 0 (default) no operation, scan does not automatically resume
n= 1 scan resumes after 2 seconds, or after the time set with the DD command.
To read: SG<CR>
Response: SGn
SELECT PRIORITY CHANNEL

PP PPmnn
m= 0-9 bank number
nn= 00-99 channel number
To read: PP<CR>
Response: PPmnn RFnnnnnnnnnn (NORMAL) or RF--- (BLANK)
AFC ON/OFF
AF AFn
n= 0 (default) AFC is off
n= 1 AFC is on (except for WFM mode)
To read: AF<CR>
Response: AFn
IF-OUT SELECTION
IF IFn
n= 0 (default) 10.7MHz
n= 1 455KHz
65
8 RESET
Should the AR-ONE appear to behave strangely, normal operation may be easily achieved
by resetting the microprocessor. Two scenarios may be encountered due to power
transients etc:
1. Symptom: LCD remains on, no control of the keypad.

Action: Remove any connection to external power and leave it for
approximately 30 seconds. Reconnect power and switch on again.
Normal operation should be restored but the last used frequency
will be lost, the AR-ONE will restore the last but one frequency to
display.
2. Symptom: The AR-ONE fails to power up.
Action: Try the suggestions given in (1) then hold the ESC key while
powering up the AR-ONE to ‘Soft reset’ the microprocessor.
Should AR-ONE still appear to behave strangely, try a ‘hard reset’ of the microprocessor, as
follows:
Remove the receiver’s top cover and push the reset button while the receiver is powered
ON (see picture below).
Put the receiver’s top cover back into place.
66
9 SPECIFICATIONS
Configuration: Triple conversion super heterodyne
Frequency coverage: 10 KHz ~ 3.3 GHz (no gap)
Receive mode: AM, NFM, WFM, USB, LSB, CW, DATA
Sensitivity: AM: – 10 dB S/N, NFM: – 12 dB SINAD, CW/SSB: – 10 dB S/N
10 ~ 40 kHz: CW 22.3 μV
40 ~ 100 kHz: AM – 4.5 μV, CW – 1.5 μV
100 kHz ~ 40 MHz: AM 2.5 μV, SSB/CW – 0.7 μV,
NFM – 0.89 μV
40 MHz ~ 1 GHz: AM – 0.89 μV, SSB/CW – 0.4 μV,
NFM – 0.5 μV, WMF – 1.5 μV
1GHz ~ 2.5 GHz: AM – 0.7 μV, SSB/CW – 0.32 μV, NFM –
0.4 μV, WFM – 1.5 μV
2.5 GHz ~ 3.3 GHz: AM – 0.9 μV, SSB/CW – 0.35 μV,
NFM – 0.5 μV, WFM – 1.5 μV
IF frequencies: 1st IF: 754 MHz / 265 MHz
2nd IF: 10.7 MHz
3rd IF: 455 KHz
Frequency steps: 1, 10, 50, 100, 500 Hz, 1, 2, 5, 6.25, 9, 10, 12.5, 25, 50, 100 KHz
(Non-standard: up to 1 MHz, 1Hz incremental)
Selectivity: BW - 6 dB -60 dB
0.5 KHz 0.5 KHz > < 2 KHz
3 KHz 3KHz > < 6 KHz
6 KHz 6 KHz> < 20 KHz
8.5 KHz 8.5 KHz > < 30 KHz
16 KHz 16 KHz > < 40 KHz
30 KHz 30 KHz > < 70 KHz
100 KHz 100 KHz > < 450 KHz
200 KHz 200 KHz > < 600 KHz
300 KHz 300 KHz > < 900 KHz
Spurious Sensitivity: 60 dB >
Adjacent Selectivity: 55 dB >
Dynamic Range: 90 dB >
Spurious emission: < - 57 dBm
rd
3 IP: + 2 dBm > (- 1 dBm > above 2.5 GHz)
Frequency stability: +/- 0.1 ppm ( -10 ~ 50℃)
67
THD: 20 dB> (< 10 %)
Audio Output: 2.0 W (at 8 ohms, THD < 10 %)
Power requirement: 13.5 V DC, < 2 A. (@ 1 W audio output)
Antenna impedance: 50 Ω
Antenna Connector: N type
IF output level: -20 dBm (10.7 MHz or 455 kHz)
Ext. freq. standard input: 10 MHz (0 dBm +/- 3 dB)
Control interface: RS-232C (9600, 19200 or 38400 bps). Default is 19200 bps.
Operating temperature: -10 ~ 50℃ (14 ~ 122°F)
Dimensions: 156(W)x58(H)x234(D)mm, 6.1”(W)x2.3”(H)9.2”(D) (Projections
excluded)
Weight: 1.9 kg (4.2 lb)
Filter bandwidth: 0.5, 3, 6, 8.5, 16, 30, 100, 200, 300 kHz (nominal)
Memory channels: 1000 (10 banks)
Scan/search rate: 25 steps/sec
68
IF-OUT SIGNAL LEVEL ACCURACY:
The on screen SIGNAL level values (dBuV or dBm), as well as the SIGNAL level values
streamed through the RS232C port to the PC, are only approximate.
For better accuracy in signal level values, connect a spectrum analyzer such as SDU5600 to
the receiver’s IF OUT port.
Make sure that both the AR-ONE and SDU5600 (or similar) are set to communicate at the
same RS232C port speed.
The signal level value accuracy through the AR-ONE’s “IF OUT” is as follows:
RF Input = -47dBm
BAND RX Freq.(MHz) 10.7M_out Range
1 0 - 1.7 0.9 -65 ～ -50
2 1.7 - 25 11.0 -65 ～ -50
3 25 - 60 42.0 -52 ～ -35
4 60 - 108 84.0 -52 ～ -33
5 108 - 142 125.0 -52 ～ -33
6 142 - 174 158.0 -52 ～ -33
7 174 - 224 199.0 -52 ～ -33
8 224 - 335 279.0 -52 ～ -33
9 335 - 480 407.0 -52 ～ -33
10 480 - 690 585.0 -52 ～ -33
11 690 - 1030 865.0 -52 ～ -33
12 1030 - 1696 1363.0 -52 ～ -33
13 1696 - 3300 2501.0 -52 ～ -33
If you wish to send these signal level values to the PC, it is advised to connect your PC to
the spectrum display’s RS232C port, not to the RS232C port of AR-ONE.
(Specifications are subject to change without notice or obligation.)
69
10 OPTIONAL ACCESSORIES
EXT-ONE Separation kit (includes a control head adapter and 16 feet
separation cable)
MM8600 Mobile mounting bracket (radio not included)
ANTENNAS
Note: DA753G is sold under the name DS3000A in the U.S
70
11 LIMITED WARRANTY (USA only)
AOR USA, Inc. (AOR) warrants the AR -ONE as described below:

AOR will repair or exchange equipment as a result of defects in parts or workmanship for a
period of one year from the date of original retail purchase from an authorized AOR dealer.
Exclusions
The following items are not covered by the AOR limited warranty:
1. Products that are damaged through accident, abuse, misuse, neglect, or user
modifications.
2. Problems that arise through failure to follow directions in the owner’s manual.
3. Exposure of the product to adverse or severe weather conditions, including
lightning, temperature extremes or water, including rainfall or immersion.
4. Exposure to toxic materials, biohazards, radioactive materials or other
contamination.
5. Repairs attempted by parties other than AOR or its authorized personnel.
6. Damage that results from improper installation, including improper voltage and/or
reversed polarity, or exposure of a receiver to signal levels exceeding
specifications.
7. Damage resulting through the use of accessories from manufacturers other than
AOR.
8. Equipment that has had serial numbers removed or altered in any way.
9. Damage that occurred as a result of shipment. Claims must be presented to the
carrier.
10. AOR is not responsible for any costs arising from installation or reinstallation of the
equipment, nor for any consequential (such as loss of use) damage claims.
Obtaining Warranty Service

1. You are responsible for shipping the product to AOR and any related costs.
2. Warranty claim must be accompanied by a legible copy of the original product
purchase receipt.
3. You must include a description of the problem(s) encountered with the
product.
4. You must include your name, a valid ground shipping address (including zip
code) and telephone contact information.
5. AOR will ship the repaired (or replaced) product by ground transport.
71
Limitations
Any and all implied warranties, including those pertaining to merchantability and utility for a
specific purpose are limited to the duration of this limited warranty.
AOR’s limits on warranty pertain only to the repair or, at its option, replacement of defective
products. AOR shall not be liable for any other damages, including consequential, incidental
or otherwise, arising from any defect.
Some states do not allow limitations on how long an implied warranty lasts and may not
allow the exclusion of incidental or consequential damages. As such, the above limitations
may not apply in every case. This warranty gives you specific legal rights and you may have
other rights that apply in your state.
If you have questions about this limited warranty, or the operation of your AOR product,
contact AOR at (310) 787-8615 during normal business hours (9 am ~ 5 pm Pacific Time
Zone), or write to AOR, 20655 S. Western Ave., Suite 112, Torrance, CA 90501. You may
also send a fax to AOR at (310) 787-8619. Additional information is available at the AOR
web site: www.aorusa.com
We suggest attaching your purchase receipt to this half of the warranty card and that you
keep this information in a secure location.
AOR Model Number __________________________
Serial Number ________________________________
Dealer Name _________________________________
Purchase Date ________________________________
72






      
                                       
                                       
                                       
                                       

                         
                                       
                                       
                                       
                                       
URL: www.aorusa.com
e-mail: [email protected]





Printed in Japan


AOR AR-ONE Operating Manual

Uploaded by

Copyright:

Available Formats

AOR AR-ONE Operating Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AOR AR-ONE Operating Manual

Uploaded by

Copyright:

Available Formats

American Communication Systems

Discover the Power of Communications ™

Operating manual v.2.1

2 Getting Started -------------------------------------------------------------------------------------------- 13

4 SCAN – scanning memory channels -------------------------------------------------------------28

5 Search mode --------------------------------------------------------------------------------------------- 30

6 Configuration menu ----------------------------------------------------------------------------------- 39

7 Computer control --------------------------------------------------------------------------------------- 52

10 Optional Accessories -------------------------------------------------------------------------------- 70

11 Limited Warranty (USA only) ---------------------------------------------------------------------- 71

© This manual is protected by copyright AOR, LTD. 2009. No information contained in

Super wide coverage: 10 KHz ~ 3.3 GHz (continuous)

1-2 Taking care of your radio

1-3 Attention while operating

Terminology – Search & Scan

SEARCH: The AR-ONE provides several operations where transmissions (active

SCAN: Once active transmission have been identified (either by searching or by

Note: It is very important that the squelch is advanced to cancel background

No noise and no “S” icon displayed (with squelch advanced clockwise

Signal received or ‘noise’ emanating from speaker (squelch fully

1-5 Controls & functions

1. Volume control plus isolate power On/Off

12. Antenna connector (N type)

RS-232C connection requirements:

1-5-2 Summary of keys

1-6 Computer control

The RS-232C parameters are as follows:

1-7 IF output and Spectrum Display Unit (SDU5600 )

2-1-2 Connect the antenna

(DC power socket design may vary depending on AR-ONE generation)

2-2 Switching on for the first time

2-3 Squelch Circuit

To select LEVEL SQUELCH, perform the following steps:

1. Push the FUNC key.

2-4 VFO selection

2-4-1 Tuning frequency

Aborting frequency input

2-4-1-3 Changing frequency using UP arrow key or DOWN arrow key

2-5 Changing receive mode

2-5-1 Auto-mode selection

2-5-2 Receive mode selection

2-6 Changing tuning STEP size

2-7-1 Manually selecting IF bandwidth

2-8 AGC (Automatic Gain Control)

2-11-1 Using pre-programmed frequency offset data

2-11-2 Entering new frequency offset data

3 Memory channels & banks

3-1 Memory channel overview

Each memory channel may hold:

3-2 Storing VFO frequencies & data into memory

3-3 Memory read “M.RD”

3-4 Deleting memory channels

4 SCAN – scanning memory channels

4-1 SCAN – outline introduction

4-2 Starting SCAN

4-3 Selecting a scan bank

4-4 Select scan

4-4-2 Starting / stopping select scan

To stop select scan, push the VFO key.