0% found this document useful (0 votes)
88 views6 pages

Cucmconfig Interface

Cucmconfig Interface

Uploaded by

Ra Yuth
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
88 views6 pages

Cucmconfig Interface

Cucmconfig Interface

Uploaded by

Ra Yuth
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Configuring Cisco Unified Communications

Manager for the


NovaTec TransNova S3 Voice Gateway

This document describes how to configure Cisco Unified Communications Manager systems to use the
NovaTec TransNova® S3 SIP Voice Gateway (S3).
NovaTec publishes complete technical information for this voice gateway on its website and in the online
help for its TransNova configuration and TraceInfo Client software. This document emphasizes
configuration that you must do within Cisco Unified Communications Manager Administration.
Calls between ISDN endpoints on the same S3 get routed through the Cisco Unified Communications
Manager, so call detail records (CDRs) can get collected.The configuration steps that are shown in this
document ensure that all calls transit the Cisco Unified Communications Manager.

Contents
This document contains the following topics:
• Configuring Call Signaling and Routing
• Configuring the Data Codec
• Downloading the S3 Configuration
• Updating the S3 Firmware

Configuring Call Signaling and Routing


This section describes procedure that you must perform with Cisco Unified Communications Manager
Administration and with the TransNova configuration software.
Perform the following procedure with Cisco Unified Communications Manager Administration.

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

© 2009 Cisco Systems, Inc. All rights reserved.


Configuring Call Signaling and Routing

Note Even though the S3 is a gateway, you configure it in Cisco Unified Communications Manager
Administration as a phone.

Task Important Notes


Step 1 Choose User Management > End User. The Find and List End Users window displays.
Step 2 Click Add New. The End User Configuration window displays.
Step 3 Enter values for User ID and Last name. Enter values only for these fields.
This user will be used for digest authentication.
Step 4 When you complete the end user information, save
your changes and add the end user by clicking
Save.
Step 5 Choose Device > Phone. The Find and List Phones window displays.
Step 6 Click the Add New button. The Add a New Phone window displays.
Step 7 From the Phone Type drop-down list box, select The Phone Configuration window displays.
“Transnova S3” and click Next.
Step 8 Enter the values that are described at the right. Enter the S3 MAC Address.
Choose defaults for all other required values in
From the Phone Button Template drop-down list
this window. Then, click Save
box, select “Standard S3”.
From the Device Security Profile drop-down list
box, select “Transnova S3 - Standard SIP
Non-Secure Profile”.
From the SIP Profile drop-down list box, select
“Standard SIP Profile”.
From the Digest User drop-down list box, select
the end user that you created in Step 3.
If your systems requires it, check the Media
Termination Point Required check box.
After you click Save, the Phone Configuration
window refreshes and adds the Association
Information field.
Step 9 From the Association Information field, click the The Directory Number Configuration window
link “Line [1] - Add a new DN”. displays.
Step 10 From the Directory Number Configuration
window, assign data as described in the section
“Directory Number Configuration Settings” of the
Cisco Unified Communications Manager
Administration Guide.
Step 11 Repeat Step 9 and Step 10 to add DNs to Lines 2,
3, and 4.

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway
2 OL-19734-01
Configuring the Data Codec

Perform the following procedure with the TransNova configuration software. For more information,
refer to the TransNova configuration software online help.

Procedure

Step 1 Configure the interface type.


Step 2 Configure the IP address, gateway name, and so on.
Step 3 Add a SIP trunk Group and assign interfaces.
Step 4 Create incoming and outgoing Dialing Plans.
Step 5 Create a trunk group for the SIP interface.
Step 6 Allocate each of the subscriber DNs to an ISDN interface.
Step 7 Configure the general SIP settings.
Step 8 Configure SIP User Mapping and Local Mapping.
Step 9 Optionally, configure NTP.

Configuring the Data Codec


This section describes procedure that you must perform with Cisco Unified Communications Manager
Administration and with the TransNova configuration software.
Perform the following procedure with Cisco Unified Communications Manager Administration.

Task Important Notes


Step 1 Choose Device > Device Settings > SIP Profile. The Find and List SIP Profiles window displays.
Step 2 Click the Add New button. The SIP Profile Configuration window displays.
Step 3 In the Name field, enter a name for the profile.
Step 4 From the Early Offer for G.Clear Calls drop-down Choose from the following types:
list box, select the applicable CODEC.
• CLEARMODE
• CCD
• G.nX64
• X-CCD (preferred)
Step 5 Click Save. The SIP Profile Configuration window refreshes
and indicates “Add successful”.
Step 6 Choose Device > Phone. The Find and List Phones window displays.
Step 7 Use the navigation tools in the Find and List
Phones window to find the S3 that you added in
Configuring Call Signaling and Routing.

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway
OL-19734-01 3
Downloading the S3 Configuration

Task Important Notes


Step 8 From the list of records that display, click the link The window displays data for the item that you
for the record that you want to view. choose.
Step 9 From the SIP Profile drop-down list box, select the
applicable SIP profile. Then, click Save.

Perform the following procedure with the TransNova configuration software. For more information,
refer to the TransNova configuration software online help.

Procedure

Step 1 Go to “TIP/SIP/SIP codec mapping” and ensure that the desired Data CODEC has Payload type 125 and
that no other CODEC has the same type. If the CODEC is not in the list, create a new CODEC.
Step 2 When you edit or create a data CODEC, set the payload type to 125 and the Bearer capability to 8890.
Step 3 If all CODECs are to be included in the initial installation, set the order in which they appear in the SDP
by selecting a CODEC and moving it up or down the list.
Step 4 Ensure that the required data CODEC is specified for each entry in the NIP/SIP/Mapping lists/User
Mapping table.

Downloading the S3 Configuration


Perform the following procedure with the TransNova configuration software. For more information,
refer to the TransNova configuration software online help.

Procedure

Step 1 Obtain the S3’s configuration database file (*.mdb file).


Step 2 Under “Extras / Network options”, set the IP address of the unit to which you want to download.
Step 3 Use “Configuration data / Process” or press the computer F7 key to prepare the configuration data.
Step 4 Select “Configuration data / Transmit to target system” or press the computer F5 key to begin the
download.

Updating the S3 Firmware


Perform the following procedure with the TransNova TraceInfo Client software. For more information,
refer to the TransNova TraceInfo Client software online help.

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway
4 OL-19734-01
Updating the S3 Firmware

Procedure

Step 1 Start the TraceInfo Client.


Step 2 Select “Settings” and configure the IP address of the S3. Leave the port set to 800. Click OK. Then, click
the Connect button. Then, click the Connect button. By default, the username is “TECHNIK”. Leave the
Password, System ID, System-Name and Dialling no. fields blank, and Network set to TCP/IP.
Step 3 Select the “Diagnosis” tab.
Step 4 Click the Firmware button and select the required firmware file. Then, click the Open button.
Step 5 At the prompt “Do you really want to upload new firmware to the target system?”, click the Yes button.
The data transmission then begins.

Note The downloaded software is not active until after you power-cycle the S3.

CCDE, CCSI, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Stackpower,
Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work,
Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA,
CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,
Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step,
Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream,
Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX,
PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient,
TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other
countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0903R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any
examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.
Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2009 Cisco Systems, Inc. All rights reserved.

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway
OL-19734-01 5
Updating the S3 Firmware

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway
6 OL-19734-01

You might also like