KALASALINGAM ACADEMY OF RESEARCH AND EDUCATI
(Deemed to be University)
Anand Nagar, Krishnankoil – 626 126.
OFFICE OF THE CONTROLLER OF EXAMINATIONS
ICE18R5004 - Computer Aided Design of Instrumentation Systems
Online Assessment -MCQ - Question Bank Report
Questions in Unit-3
Topic: Parallel port - parallel port as output port
The basic difference between a parallel and a serial communication channel is the number of electrical c
77020 _____________ layer to convey bits.
Options - Correct answer: 2
(1) transport
(2) physical
(3) datalink
(4) None of the above
77470 Parallel ports are capable of detecting interrupt signals from a peripheral, LPT1 uses _______________
Options - Correct answer: 4
(1) IQR5
(2) IQR4
(3) IQR2
(4) IQR7
77536 ECPs can use_____________________ memory access for data transfers at the parallel port.
Options - Correct answer: 2
(1) indirect
(2) direct
(3) both
(4) None of the above
78005 SCSI (small computer system interface) is a parallel interface that allows up to ___________devices to
cable
Options - Correct answer: 2
(1) 4
(2) 7
(3) 5
(4) 6
78058 SCSI interfaces are fast, and the cable can be as long as____________ meters.
Options - Correct answer: 4
(1) 1
(2) 2
(3) 4
(4) 6
79956 ECR mode 001 descriptions for the FDC37C665/66 chip is
Options - Correct answer: 2
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
79964 ECR mode 010 descriptions for the FDC37C665/66 chip is
Options - Correct answer: 3
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
79979 ECR mode 011 descriptions for the FDC37C665/66 chip is
Options - Correct answer: 4
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
80008 ECR mode 100 description for the FDC37C665/66 chip is
Options - Correct answer: 1
(1) EPP mode
(2) Reserved
(3) Test mode
(4) Configuration mode
80019 ECR mode 101 description for the FDC37C665/66 chip is
Options - Correct answer: 2
(1) SPP mode
(2) Reserved
(3) Test mode
(4) Configuration mode
80027 ECR mode 110 description for the FDC37C665/66 chip is
Options - Correct answer: 3
(1) EPP mode
(2) Reserved
(3) Test mode
(4) Configuration mode
80032 ECR mode 111 description for the FDC37C665/66 chip is
Options - Correct answer: 4
(1) EPP mode
(2) Reserved
(3) Test mode
(4) Configuration mode
80867 IEEE 1284’s ________________________enables devices to talk back and forth to decide the best mod
Options - Correct answer: 1
(1) negotiation phase
(2) test phase
(3) read phase
(4) write phase
Topic: Parallel Port (PP) Interfacing Techniques
80792 ____________ defines a way that all ports can use to transfer data in the reverse direction, from the per
Options - Correct answer: 2
(1) Compatibility mode
(2) Nibble mode
(3) Register mode
(4) None of the above
80804 _________________ is similar to the data-transfer protocol used by the BIOS in the original PC.
Options - Correct answer: 1
(1) Compatibility mode
(2) Byte mode
(3) Nibble mode
(4) None of the above
80819 _____________________ defines a way to transfer data in the reverse direction, from the peripheral
to the host, when the data lines are bidirectional.
Options - Correct answer: 1
(1) Byte mode
(2) EPP mode
(3) ECP mode
(4) Nibble mode
65036 How many pins are in a parallel port?
Options - Correct answer: 1
(1) 25
(2) 9
(3) 24
(4) 12
65241 A____________port is an interface allowing a personal computer (PC) to transmit or receive data down
peripheral device such as a printer.
Options - Correct answer: 3
(1) Serial
(2) USB
(3) parallel
(4) Not mention
77505 Parallel ports are capable of detecting interrupt signals from a peripheral, the LPT2 uses ____________
Options - Correct answer: 4
(1) IRQ7
(2) IRQ1
(3) IRQ3
(4) IRQ5
77092 ____________________creates interference between the parallel lines
Options - Correct answer: 3
(1) noise
(2) Sound
(3) Crosstalk
(4) None of the above
77435 In the parallel port, IRQ stand for
Options - Correct answer: 3
(1) interrupt-request logic
(2) interrupt-return level
(3) interrupt-request level
(4) interrupt-request logic
80729 Parallel-port standard has the designation______________________
Options - Correct answer: 1
(1) IEEE Std 1284
(2) IEEE Std 1284a
(3) IEEE Std 1284b
(4) IEEE Std 1284c
80758 The_______________ is responsible for detecting nStrobe in parallel port interface
Options - Correct answer: 1
(1) peripheral
(2) pc
(3) both
(4) none of the above
76704 In the D25 parallel port has, how many numbers of data signal lines?
Options - Correct answer: 4
(1) 4
(2) 8
(3) 5
(4) 8
76712 In the D25 parallel port has, how many numbers of output control signal line?
Options - Correct answer: 3
(1) 5
(2) 6
(3) 4
(4) 3
76720 In the D25 parallel port has, how many numbers of input control signal line?
Options - Correct answer: 1
(1) 5
(2) 4
(3) 3
(4) 2
76729 In the D25 parallel port has, how many numbers of ground signal line?
Options - Correct answer: 4
(1) 4
(2) 5
(3) 8
(4) 9
76738 In the D25 parallel port has, how many numbers of control signal lines?
Options - Correct answer: 4
(1) 4
(2) 6
(3) 7
(4) 8
76791 In the parallel port, EPP stands for
Options - Correct answer: 2
(1) Enhanc Parallel Port
(2) Enhanced Parallel Port
(3) Enhanced Capability Port
(4) None of the above
76813 In the parallel port, ECP stands for
Options - Correct answer: 1
(1) Enhanced Capability Port
(2) Enhanced Capacity Port
(3) Enhanced Counter Port
(4) None of the above
76836 In the parallel port, SPP stands for
Options - Correct answer: 1
(1) Standard Parallel Port
(2) Standard Paaused Port
(3) Serial Parallel Port
(4) None of the above
76865 The Standard Parallel Port belongs to which type?
Options - Correct answer: 3
(1) Type 3
(2) Type 2
(3) Type 1
(4) None of the above
76894 Parallel Port DMA belongs to which type no.?
Options - Correct answer: 3
(1) Type 1
(2) Type 2
(3) Type 3
(4) None of the above
76914 The DMA type 3 parallel port used by only
Options - Correct answer: 1
(1) IBM
(2) HCL
(3) AUSU
(4) None of the above
76948 The unidirectional type of parallel port has _________bit
Options - Correct answer: 4
(1) 8
(2) 16
(3) 1
(4) 4
76957 The bidirectional type of parallel port has _________bit
Options - Correct answer: 4
(1) 1
(2) 2
(3) 4
(4) 8
76992 In data transmission, parallel communication is a method of conveying multiple ___________digits (bit
Options - Correct answer: 2
(1) decimal
(2) binary
(3) hexadecimal
(4) None of the above
Topic: Parallel port as input port and its programming
80462 Data port addresses for the LPT1:PC ports of the centronics printer adapter is___________
Options - Correct answer: 1
(1) 3BChx
(2) 378h
(3) 278h
(4) None of the above
80473 Data port addresses for the LPT2:PC ports of the centronics printer adapter is___________
Options - Correct answer: 2
(1) 3BChx
(2) 378h
(3) 278h
(4) None of the above
80482 Data port addresses for the LPT3:AT ports of the centronics printer adapter is___________
Options - Correct answer: 3
(1) 3BChx
(2) 378h
(3) 278h
(4) None of the above
80492 Status port addresses for the LPT1:PC ports of the centronics printer adapter is___________
Options - Correct answer: 1
(1) 3BDh
(2) 379h
(3) 279h
(4) None of the above
80500 Status port addresses for the LPT2:PC ports of the centronics printer adapter is___________
Options - Correct answer: 2
(1) 3BDh
(2) 379h
(3) 279h
(4) None of the above
80505 Status port addresses for the LPT3:AT ports of the centronics printer adapter is___________
Options - Correct answer: 3
(1) 3BDh
(2) 379h
(3) 279h
(4) None of the above
80511 Control port addresses for the LPT1:PC ports of the centronics printer adapter is___________
Options - Correct answer: 1
(1) 3BEh
(2) 37Ah
(3) 27Ah
(4) None of the above
80518 Control port addresses for the LPT2:PC ports of the centronics printer adapter is___________
Options - Correct answer: 2
(1) 3BEh
(2) 37Ah
(3) 27Ah
(4) None of the above
80529 Control port addresses for the LPT3:AT ports of the centronics printer adapter is___________
Options - Correct answer: 3
(1) 3BEh
(2) 37Ah
(3) 27Ah
(4) None of the above
78244 The standard parallel port uses three ___________-bit port registers in the PC.
Options - Correct answer: 4
(1) 4
(2) 2
(3) 1
(4) 8
77579 parallel port supports ECP transfers, assign it __________
Options - Correct answer: 3
(1) IRQ level
(2) DMA channel
(3) both
(4) None of the above
77769 The ECP’s internal modes enable the port to emulate an __________
Options - Correct answer: 3
(1) EPP
(2) PS/2
(3) SPP
(4) None of the above
77983 The parallel interface SCSI stands for
Options - Correct answer: 4
(1) serial computer system interface
(2) small computer serial interface
(3) small connector system interface
(4) small computer system interface
80108 ECR mode 000 descriptions for the PC87332 chip is
Options - Correct answer: 1
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
80134 ECR mode 011 descriptions for the PC87332 chip is
Options - Correct answer: 4
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
80168 ECR mode 110 description for the PC87332 chip is
Options - Correct answer: 3
(1) ECP mode
(2) Reserved
(3) FIFO test mode
(4) Configuration mode
80177 ECR mode 101 description for the PC87332 chip is
Options - Correct answer: 2
(1) ECP mode
(2) Reserved
(3) FIFO test mode
(4) Configuration mode
80187 ECR mode 100 description for the PC87332 chip is
Options - Correct answer: 2
(1) ECP mode
(2) Reserved
(3) FIFO test mode
(4) Configuration mode
79949 ECR mode 000 descriptions for the FDC37C665/66 chip is
Options - Correct answer: 1
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
Topic: Programming of Parallel port
80157 ECR mode 111 description for the PC87332 chip is
Options - Correct answer: 4
(1) ECP mode
(2) Reserved
(3) FIFO test mode
(4) Configuration mode
80116 ECR mode 001 descriptions for the PC87332 chip is
Options - Correct answer: 2
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
80128 ECR mode 010 descriptions for the PC87332 chip is
Options - Correct answer: 3
(1) SPP mode
(2) PS/2 parallel port mode
(3) Parallel port data FIFO mode
(4) ECP mode
77628 SPP is also called
Options - Correct answer: 1
(1) AT-type
(2) simple bi-direction mode
(3) Ps/2 type
(4) None of the above
78044 SCSI interfaces are fast, and the cable can be as long as ___________ feet
Options - Correct answer: 2
(1) 190
(2) 19
(3) 1.9
(4) .19
78086 The GPIB stands for
Options - Correct answer: 3
(1) general-purpose interconnect bus
(2) general-purpose interlink bus
(3) general-purpose interface bus
(4) None of the above
78109 IEEE-488 parallel interface that enables up to _____________devices
Options - Correct answer: 3
(1) 5
(2) 10
(3) 15
(4) 20
78125 IEEE-488 parallel interface that enables up to 15 devices to communicate at speeds of up to _________
Options - Correct answer: 1
(1) 1
(2) 10
(3) 100
(4) 1000
78888 EPP BIOS calls_________________________ is used to test for the presence of an EPP port.
Options - Correct answer: 1
(1) Installation Check
(2) Address Read
(3) Address write
(4) None of the above
78896 EPP BIOS calls _________________________ is used to set the operating mode of the EPP port.
Options - Correct answer: 1
(1) Set Mode
(2) Get mode
(3) EPP Reset
(4) None of the above
78899 EPP BIOS calls _________________________ is used to query the current operating mode of the EPP
Options - Correct answer: 1
(1) Get Mode
(2) Set mode
(3) EPP reset
(4) None of the above
78928 EPP BIOS calls _________________________ is used to reset the peripheral connected to the EPP por
Options - Correct answer: 1
(1) EPP Reset
(2) Address read
(3) Address Write
(4) None of the above
78939 EPP BIOS calls _________________________ is used to perform an address read I/O cycle.
Options - Correct answer: 1
(1) Address Read
(2) Set mode
(3) Get mode
(4) None of the above
78955 EPP BIOS calls _________________________ is used to perform an address write I/O cycle.
Options - Correct answer: 1
(1) Address Write
(2) Set mode
(3) Get mode
(4) None of the above
78971 EPP BIOS calls _________________________ is used to output a single byte via the EPP data port.
Options - Correct answer: 1
(1) Write Byte
(2) Installation Check
(3) set mode
(4) None of the above
78980 EPP BIOS calls _________________________ is used to output a block of user-specified data from a d
port data from a defined buffer via the EPP data port.
Options - Correct answer: 1
(1) Write Block
(2) Installation Check
(3) Interrupt Control
(4) None of the above
78988 EPP BIOS calls _________________________ is used to read a single byte via the EPP data port.
Options - Correct answer: 1
(1) Read Byte
(2) Installation Check
(3) Interrupt Control
(4) None of the above
78993 EPP BIOS calls_________________________ is used to input a stream of bytes into a user-defined buf
Options - Correct answer: 1
(1) Read Block
(2) Installation Check
(3) Set mode
(4) None of the above
78999 EPP BIOS calls _________________________ is used to allow an EPP device driver to install an interr
Options - Correct answer: 1
(1) Device Interrupt
(2) Installation Check
(3) Set mode
(4) None of the above
Questions in Unit-4
Topic: Programming of Serial Port
What is the maximum connected distance in ft by using RS-232 (TIA-232) data cable?
60688
Options - Correct answer: 1
(1) 100
(2) 50
(3) 25
(4) 12
60693 What is the maximum connected distance in ft by using RS-485 (TIA-485) data cable?
Options - Correct answer: 1
(1) 4000
(2) 1000
(3) 1024
(4) 512
60699 What is the maximum connected distance in ft by using Ethernet data cable?
Options - Correct answer: 1
(1) 1600
(2) 160
(3) 16
(4) 1.6
60707 What is the maximum connected distance in ft by using IEEE-1394b data cable?
Options - Correct answer: 1
(1) 300
(2) 30
(3) 3
(4) 0.3
60710 What is the maximum connected distance in ft by using FireWire 800 data cable?
Options - Correct answer: 1
(1) 300
(2) 30
(3) 3
(4) .3
60713 What is the maximum connected distance in ft by using I2C data cable?
Options - Correct answer: 1
(1) 18
(2) 180
(3) 1800
(4) 1.8
60717 What is the maximum connected distance in ft by using Microwire data cable?
Options - Correct answer: 1
(1) 10
(2) 100
(3) 1000
(4) 1
60722 What is the maximum connected distance in ft by using MIDI data cable?
Options - Correct answer: 1
(1) 50
(2) 500
(3) 5
(4) 0.5
60729 What is the maximum connected distance in ft by using SPI data cable?
Options - Correct answer: 1
(1) 10
(2) 1
(3) 100
(4) 1000
60737 What is the maximum connected distance in ft by using USB data cable?
Options - Correct answer: 1
(1) 16
(2) 32
(3) 64
(4) 128
60817 What is the maximum connected distance in m by using RS-232 (TIA-232) data cable?
Options - Correct answer: 1
(1) 30
(2) 60
(3) 120
(4) 150
60821 What is the maximum connected distance in m by using RS-485 (TIA-485) data cable?
Options - Correct answer: 3
(1) 126
(2) 512
(3) 1200
(4) 12
60827 What is the maximum connected distance in m by using Ethernet data cable?
Options - Correct answer: 4
(1) 240
(2) 60
(3) 120
(4) 480
60833 What is the maximum connected distance in m by using IEEE-1394b data cable?
Options - Correct answer: 4
(1) 10
(2) 20
(3) 40
(4) 90
60838 What is the maximum connected distance in m by using FireWire 800 data cable?
Options - Correct answer: 4
(1) 1
(2) 10
(3) 126
(4) 90
60842 What is the maximum connected distance in m by using I2C data cable?
Options - Correct answer: 4
(1) 1.2
(2) 3.6
(3) 2.4
(4) 5.40
60845 What is the maximum connected distance in m by using Microwire data cable?
Options - Correct answer: 2
(1) 1
(2) 3
(3) 2
(4) 5
60855 What is the maximum connected distance in m by using MIDI data cable?
Options - Correct answer: 3
(1) 152
(2) 153
(3) 15
(4) 1.5
60861 What is the maximum connected distance in m by using SPI data cable?
Options - Correct answer: 3
(1) .03
(2) .3
(3) 3
(4) 30
60863 What is the maximum connected distance in m by using USB data cable?
Options - Correct answer: 2
(1) 480
(2) 48
(3) 4800
(4) 4.8
60321 How many number of devices(maximum) connected by using RS-232 (TIA-232) data cable?
Options - Correct answer: 1
(1) 2
(2) 3
(3) 4
(4) 8
60323 How many number of devices(maximum) connected by using RS-485 (TIA-485) data cable?
Options - Correct answer: 1
(1) 32
(2) 64
(3) 16
(4) 128
60333 How many number of devices(maximum) connected by using Ethernet data cable?
Options - Correct answer: 1
(1) 1024
(2) 1023
(3) 512
(4) 511
60339 How many number of devices(maximum) connected by using IEEE-1394b data cable?
Options - Correct answer: 1
(1) 64
(2) 128
(3) 256
(4) 31
60344 How many number of devices(maximum) connected by using FireWire 800 data cable?
Options - Correct answer: 1
(1) 64
(2) 32
(3) 16
(4) 8
60352 How many number of devices(maximum) connected by using I2C data cable?
Options - Correct answer: 1
(1) 40
(2) 20
(3) 10
(4) 5
60354 How many number of devices(maximum) connected by using Microwire data cable?
Options - Correct answer: 1
(1) 8
(2) 4
(3) 2
(4) 1
60356 How many number of devices(maximum) connected by using MIDI data cable?
Options - Correct answer: 1
(1) 2
(2) 1
(3) 4
(4) 8
60358 How many number of devices(maximum) connected by using SPI data cable?
Options - Correct answer: 1
(1) 8
(2) 4
(3) 2
(4) 1
60365 How many number of devices(maximum) connected by using USB data cable?
Options - Correct answer: 1
(1) 127
(2) 256
(3) 128
(4) 64
61224 What is the maximum data transfer speed in bps by using the IEEE-1394b data cable?
Options - Correct answer: 3
(1) 3.2K
(2) 3.2M
(3) 3.2G
(4) 32G
Topic: serial port - Serial port as output port
61738 In the PC conventional COM 1 port address is ________
Options - Correct answer: 2
(1) 4F8h
(2) 3F8h
(3) 2F8h
(4) 5F8h
59338 What is the IEEE standard number for the FireWire 800?
Options - Correct answer: 1
(1) IEEE-1394b
(2) IEEE-1394a
(3) IEEE-1394c
(4) IEEE-1394d
59510 The RS-232 (TIA-232) cable data transfer based on _____________format.
Options - Correct answer: 1
(1) asynchronous serial
(2) serial
(3) synchronous serial
(4) parallel
59515 The RS-485 (TIA-485) cable data transfer based on _____________format.
Options - Correct answer: 1
(1) asynchronous serial
(2) serial
(3) synchronous serial
(4) parallel
59521 The Ethernet cable data transfer based on _____________format.
Options - Correct answer: 1
(1) serial
(2) parallel
(3) asynchronous serial
(4) synchronous serial
59526 The IEEE-1394b cable data transfer based on _____________format.
Options - Correct answer: 1
(1) serial
(2) parallel
(3) synchronous serial
(4) asynchronous serial
59531 The I2C cable data transfer based on _____________format.
Options - Correct answer: 1
(1) synchronous serial
(2) parallel
(3) asynchronous serial
(4) serial
59537 The Microwire cable data transfer based on _____________format.
Options - Correct answer: 1
(1) synchronous serial
(2) parallel
(3) asynchronous serial
(4) serial
59541 The MIDI cable data transfer based on _____________format.
Options - Correct answer: 1
(1) serial current loop
(2) parallel
(3) asynchronous serial
(4) synchronous serial
59547 The SPI cable data transfer based on _____________format.
Options - Correct answer: 1
(1) synchronous serial
(2) parallel
(3) asynchronous serial
(4) serial
59553 The USB cable data transfer based on _____________format.
Options - Correct answer: 1
(1) asynchronous serial
(2) parallel
(3) serial
(4) synchronous serial
59557 The Fire Wirw 800 cable data transfer based on _____________format.
Options - Correct answer: 1
(1) serial
(2) parallel
(3) asynchronous serial
(4) synchronous serial
Topic: Serial Port (SP) Interfacing Techniques
59117 Serial ports can also be a ____________ choice when you need very long cables among PCs, embedded
Options - Correct answer: 4
(1) Very worst
(2) worst
(3) better
(4) good
59153 The serial port cables are_____________
Options - Correct answer: 1
(1) low cost
(2) medium cost
(3) high cost
(4) very high cost
59065 A serial port is a computer interface that transmits data ____________ bit at a time.
Options - Correct answer: 1
(1) 1
(2) 8
(3) 2
(4) 4
61686 The USB stands for _____________
Options - Correct answer: 4
(1) Universal serial baud rate
(2) united serial bus
(3) united serial baud
(4) Universal serial bus
61418 The ____________ is the number of bits per second transmitted or received per unit of time.
Options - Correct answer: 4
(1) baud rate
(2) word rate
(3) nibble rate
(4) bit rate
61517 UART stands for ________
Options - Correct answer: 3
(1) Universal Asynchronous Relay Transmission
(2) Universal Accumulator Register Transfer
(3) Universal Asynchronous Receiver Transmitter
(4) None of the mentioned
61530 In a serial port interface, the INTR line is connected to _____
Options - Correct answer: 1
(1) Status register
(2) Shift register
(3) Chip select
(4) None of the mentioned
61548 The data transfer in UART is done in ______
Options - Correct answer: 1
(1) Asynchronous start stop format
(2) Synchronous start stop format
(3) Isochronous format
(4) EBDIC format
61570 The standard used in serial ports to facilitate communication is _____
Options - Correct answer: 3
(1) RS-246
(2) RS-LNK
(3) RS-232-C
(4) Both RS-246 and RS-LNK
37295 A ___________ is a connection from the outside world to the microprocessor.
Options - Correct answer: 1
(1) port
(2) Serial port
(3) parallel port
(4) baud rate
Topic: Serial port as input port and its programming
61205 What is the maximum data transfer speed in bps by using RS-232 (TIA-232) data cable?
Options - Correct answer: 4
(1) 1k
(2) 2k
(3) 4k
(4) 20k
61211 What is the maximum data transfer speed in bps by using RS-485 (TIA-485) data cable?
Options - Correct answer: 4
(1) 1M
(2) 2M
(3) 3M
(4) 10M
61217 What is the maximum data transfer speed in bps by using Ethernet data cable?
Options - Correct answer: 4
(1) 3G
(2) 120G
(3) 20G
(4) 10G
61228 What is the maximum data transfer speed in bps by using FireWire 800 data cable?
Options - Correct answer: 2
(1) 2G
(2) 3.G
(3) 1G
(4) 5G
61233 What is the maximum data transfer speed in bps by using I2C data cable?
Options - Correct answer: 4
(1) 13.4M
(2) 3.41M
(3) 3.42M
(4) 3.4M
61240 What is the maximum data transfer speed in bps by using Microwire data cable?
Options - Correct answer: 3
(1) 12M
(2) 20M
(3) 2M
(4) 0. 2M
61244 What is the maximum data transfer speed in bps by using MIDI data cable?
Options - Correct answer: 3
(1) 315K
(2) 3.15K
(3) 31.5K
(4) 4K
61247 What is the maximum data transfer speed in bps by using SPI data cable?
Options - Correct answer: 4
(1) 12.1M
(2) 22.1M
(3) 2.12M
(4) 2.1M
61254 What is the maximum data transfer speed in bps by using USB data cable?
Options - Correct answer: 4
(1) 4800M
(2) 48M
(3) 4.80M
(4) 480M
61301 Which one is the most appropriate use with RS-232 (TIA-232) data cable?
Options - Correct answer: 1
(1) Modem
(2) Data acquisition and control systems
(3) PC network communication
(4) Music
61307 Which one is the most appropriate use with RS-485 (TIA-485) data cable?
Options - Correct answer: 1
(1) Data acquisition and control systems
(2) PC network communication
(3) Music
(4) Video
61312 Which one is the most appropriate use with Ethernet data cable?
Options - Correct answer: 1
(1) PC network communication
(2) Data acquisition and control systems
(3) Music
(4) Video
61318 Which one is the most appropriate use with IEEE-1394b data cable?
Options - Correct answer: 1
(1) Video
(2) PC network communication
(3) Music
(4) Data acquisition and control systems
61323 Which one is the most appropriate use with FireWire 800 data cable?
Options - Correct answer: 1
(1) Mass storage
(2) PC network communication
(3) Data acquisition and control systems
(4) Music
61333 Which one is the most appropriate use with I2C data cable?
Options - Correct answer: 1
(1) Microcontroller communication
(2) Data acquisition and control systems
(3) PC network communication
(4) Video
61335 Which one is the most appropriate use with Microwire data cable?
Options - Correct answer: 1
(1) Microcontroller communication
(2) Data acquisition and control systems
(3) PC network communication
(4) Video
61337 Which one is the most appropriate use with MIDI data cable?
Options - Correct answer: 1
(1) Music
(2) PC network communication
(3) Data acquisition and control systems
(4) Video
61343 Which one is the most appropriate use with SPI data cable?
Options - Correct answer: 1
(1) Microcontroller communication
(2) PC network communication
(3) Data acquisition and control systems
(4) Video
61347 Which one is the most appropriate use with USB data cable?
Options - Correct answer: 1
(1) PC peripherals
(2) PC network communication
(3) Data acquisition and control systems
(4) Video
61367 For the Data acquisition and control systems________ interface is best?
Options - Correct answer: 1
(1) RS-485
(2) SPI
(3) MIDI
(4) I2C
61372 For the PC network communications________ interface is best?
Options - Correct answer: 1
(1) Ethernet
(2) SPI
(3) MIDI
(4) I2C
61380 For the PC peripherals ________ interface is best?
Options - Correct answer: 1
(1) USB
(2) SPI
(3) MIDI
(4) I2C
