Scribd
Upload
134 views3 pages

Iot Based Health Monitoring System Code

This document describes an IOT based health monitoring system that uses an Arduino board and pulse sensor to measure a patient's heart rate and body temperature. It connects to WiFi using an ESP8266 module and sends the health readings and any panic button presses to a remote server every 10 seconds.

Uploaded by

Mahesh Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
134 views3 pages

Iot Based Health Monitoring System Code

This document describes an IOT based health monitoring system that uses an Arduino board and pulse sensor to measure a patient's heart rate and body temperature. It connects to WiFi using an ESP8266 module and sends the health readings and any panic button presses to a remote server every 10 seconds.

Uploaded by

Mahesh Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

IOT BASED HEALTH MONITORING SYSTEM.

PROJECT CODE
#define USE_ARDUINO_INTERRUPTS true
#define DEBUG true
#define SSID "********" // "SSID-WiFiname"
#define PASS "************" // "password"
#define IP "184.106.153.149" // thingspeak.com ip

#include <SoftwareSerial.h>
#include "Timer.h"
#include <PulseSensorPlayground.h> // Includes the PulseSensorPlayground Library.
Timer t;
PulseSensorPlayground pulseSensor;

String msg = "GET /update?key=your api key";


SoftwareSerial esp8266(10,11);

//Variables
const int PulseWire = A0; // PulseSensor PURPLE WIRE connected to ANALOG PIN 0
const int LED13 = 13; // The on-board Arduino LED, close to PIN 13.
int Threshold = 550; //for heart rate sensor
float myTemp;
int myBPM;
String BPM;
String temp;
int error;
int panic;
int raw_myTemp;
float Voltage;
float tempC;
void setup()
{

Serial.begin(9600);
esp8266.begin(115200);
pulseSensor.analogInput(PulseWire);
pulseSensor.blinkOnPulse(LED13); //auto-magically blink Arduino's LED with heartbeat.
pulseSensor.setThreshold(Threshold);

// Double-check the "pulseSensor" object was created and "began" seeing a signal.
if (pulseSensor.begin()) {
Serial.println("We created a pulseSensor Object !"); //This prints one time at Arduino power-up, or on
Arduino reset.
}
Serial.println("AT");
esp8266.println("AT");

delay(3000);

if(esp8266.find("OK"))
{
connectWiFi();
}
t.every(10000, getReadings);
t.every(10000, updateInfo);
}

void loop()
{
panic_button();
start: //label
error=0;
t.update();
//Resend if transmission is not completed
if (error==1)
{
goto start; //go to label "start"
}
delay(4000);
}

void updateInfo()
{
String cmd = "AT+CIPSTART=\"TCP\",\"";
cmd += IP;
cmd += "\",80";
Serial.println(cmd);
esp8266.println(cmd);
delay(2000);
if(esp8266.find("Error"))
{
return;
}
cmd = msg ;
cmd += "&field1="; //field 1 for BPM
cmd += BPM;
cmd += "&field2="; //field 2 for temperature
cmd += temp;
cmd += "\r\n";
Serial.print("AT+CIPSEND=");
esp8266.print("AT+CIPSEND=");
Serial.println(cmd.length());
esp8266.println(cmd.length());
if(esp8266.find(">"))
{
Serial.print(cmd);
esp8266.print(cmd);
}
else
{
Serial.println("AT+CIPCLOSE");
esp8266.println("AT+CIPCLOSE");
//Resend...
error=1;
}
}

boolean connectWiFi()
{
Serial.println("AT+CWMODE=1");
esp8266.println("AT+CWMODE=1");
delay(2000);
String cmd="AT+CWJAP=\"";
cmd+=SSID;
cmd+="\",\"";
cmd+=PASS;
cmd+="\"";
Serial.println(cmd);
esp8266.println(cmd);
delay(5000);
if(esp8266.find("OK"))
{
return true;
}
else
{
return false;
}
}

void getReadings(){
raw_myTemp = analogRead(A1);
Voltage = (raw_myTemp / 1023.0) * 5000; // 5000 to get millivots.
tempC = Voltage * 0.1;
myTemp = (tempC * 1.8) + 32; // conver to F
Serial.println(myTemp);
int myBPM = pulseSensor.getBeatsPerMinute(); // Calls function on our pulseSensor object that returns
BPM as an "int".
// "myBPM" hold this BPM value now.
if (pulseSensor.sawStartOfBeat()) { // Constantly test to see if "a beat happened".
Serial.println(myBPM); // Print the value inside of myBPM.
}

delay(20);
char buffer1[10];
char buffer2[10];
BPM = dtostrf(myBPM, 4, 1, buffer1);
temp = dtostrf(myTemp, 4, 1, buffer2);
}

void panic_button(){
panic = digitalRead(8);
if(panic == HIGH){
Serial.println(panic);
String cmd = "AT+CIPSTART=\"TCP\",\"";
cmd += IP;
cmd += "\",80";
Serial.println(cmd);
esp8266.println(cmd);
delay(2000);
if(esp8266.find("Error"))
{
return;
}
cmd = msg ;
cmd += "&field3=";
cmd += panic;
cmd += "\r\n";
Serial.print("AT+CIPSEND=");
esp8266.print("AT+CIPSEND=");
Serial.println(cmd.length());
esp8266.println(cmd.length());
if(esp8266.find(">"))
{
Serial.print(cmd);
esp8266.print(cmd);
}
else
{
Serial.println("AT+CIPCLOSE");
esp8266.println("AT+CIPCLOSE");
//Resend...
error=1;
}
}
}

You might also like