Extraction Metallurgy C B Perry 123s

Extraction Metallurgy
Part 2: Case studies
Dr. C.B. Perry (C306)
http://www.gh.wits.ac.za/chemnotes
Chem 3033
Extraction Metallurgy
Part 2: Case studies
• Copper – Pyrometallurgy route and environmental concerns. The
hydrometallurgical alternative.
• Hydrometallurgical processes – ion exchange processes,

solvent extraction, and bacterial leaching.
• Iron – Pyrometallurgy and the blast furnace.
• Silicon – The electric arc furnace. Purification by the Czochralski

process.
• Aluminium – Electrolytic reduction.
• The siderophiles – The extraction of Au and the Pt group metals

and their purification.
Pyrometallurgy of copper
Reminder: Pyrometallurgy is the use of heat to reduce
the mineral to the free metal, and usually
involves 4 main steps:
1. Calcination: thermal decomposition of the ore with
associated elimination of a volatile product.
2. Roasting: a metallurgical treatment involving gas-

solids reactions at elevated temperatures.
3. Smelting: a melting process which separates the

chemical reaction products into 2 or more layers.
4. Refining: treatment of a crude metal product to improve its

purity.
Cu ore usually associated with sulphide minerals.
Most common source of Cu ore is the mineral

chalcopyrite (CuFeS2), which accounts for ± 50% of Cu
production.
Other important ores include:

chalcocite [Cu2S],
malachite [CuCO3 • Cu(OH)2],
azurite [2CuCO3 • Cu(OH)2],
bornite (3Cu2S • Fe2S3),
covellite (CuS).
The following steps are involved in Cu extraction:
1. Concentration
2. Roasting
3. Smelting
4. Conversion
5. Refining
1. Concentration
Finely crushed ore concentrated by the froth-flotation
process:
• Ground ore mixed with xanthates (salts & esters of
xanthic acid), dithiophosphates, or thionocarbamates.
These make the ore surface hydrophobic.
• Ore then introduced into a water bath where air is

bubbled through the suspension.
• Finely divided hydrophobic ore particles latch on to the

air bubbles and travel to the surface where a froth is
formed.
1. Concentration (cont.)
• The froth containing the Cu ore is skimmed off and
reprocessed.
• The remaining material (sand particles & other

impurities) sink to the bottom & is discarded or
reprocessed to extract other elements.
1. Concentration (cont.)
Froth-flotation
2. Roasting
• Involves partial oxidation of the sulphide mineral with
air at between 500C and 700C.
• For chalcopyrite, the main reactions are:
CuFeS2(s) + 4O2(g) → CuSO4(s) + FeSO4(s)
4CuFeS2(s) + 13O2(g) → 4CuO(s) + 2Fe2O3(s) + 8SO2(g)
• Reactions are exothermic,  roasting is an autogenous
process requiring little or no additional fuel.
• NB, not all the sulphides are oxidised, only around 1/3.
Rest remain as sulphide minerals.
• The gases produced contain around 5 – 15% SO2, which
is used for sulphuric acid production.
2. Roasting (cont.)
Objectives of roasting:
1) Remove part of the sulphur.
2) Convert iron sulphides into iron oxide and iron

sulphate to facilitate removal during smelting.
3) To pre-heat the concentrate to reduce amount of

energy needed by the smelter.
3. Smelting
• Smelting consists of melting the roasted concentrate
to form 2 molten phases:
1) a sulphide “matte”, which contains the iron-copper
sulphide mixture.
2) an oxide slag, which is insoluble in the matte, and
contains iron oxides, silicates, and other impurities.
• Smelting is carried out at around 1200C, usually with a

silica flux to make the slag more fluid.
• The matte layer sinks to the bottom, and the slag layer
floats on top of the matte & is tapped off & disposed of.
3. Smelting (cont.)
• The main reaction is the reduction of copper oxides
(formed during roasting) back into copper sulphide to
ensure that they migrate into the matte phase:
FeS(l) + 6CuO(l) → 3Cu2O(l) + FeO(l) + SO2(g)

FeS(l) + Cu2O(l) → FeO(l) + Cu2S(l)
Cu2S(l) + FeS(l) → Cu2S•FeS(l) (matte)
4. Conversion
• After smelting, matte contains from between 30 to
80% Cu in the form of copper sulphide.
• The sulphur is removed by selective oxidation of the

matte with O2 to produce SO2 from S, but leave Cu
metal.
• Converting is carried out in two stages: 1) an iron

removal stage, and 2) a copper-making stage.
4. Conversion (cont.)
Iron removal
• A silica flux is added to keep the slag (see below)
molten.
• Air is blown into the converter to oxidize the iron
sulphide according to the following reaction:
2Cu2S•FeS(l) + 3O2(g) + SiO2(l) → 2FeO•SiO2(l) + 2SO2(g) + Cu2S(l)
• The oxidized Fe and Si form a slag (insoluble in

matte) that is skimmed off & disposed off.
4. Conversion (cont.)
Copper making
• The sulphur in the Cu2S can now be oxidized to
leave behind metallic copper according to the
following reaction:
Cu2S(l) + O2(g) → 2Cu(l) + SO2(g)
• The end product is around 98.5% pure & is known as

blister copper because of the broken surface created
by the escape of SO2 gas.
5. Refining
• The copper is refined by electrolysis.
• The anodes (cast from blister copper) are placed into

an aqueous CuSO4/H2SO4 solution.
• Thin sheets of highly pure Cu serve as the cathodes.
• Application of a suitable voltage causes oxidation of

Cu metal at the anode.
• Cu2+ ions migrate through the electrolyte to the

cathode, where Cu metal plates out.
5. Refining (cont.)
• Metallic impurities more active then Cu are oxidized at

the anode, but don’t plate out at the cathode.
• Less active metals are not oxidized at the anode, but
collect at the bottom of the cell as a sludge.
• The redox reactions are:
Cu(s)  Cu2+(aq) 2e-
Cu2+(aq) + 2e-  Cu(s) Ered = -0.83V
5. Refining (cont.)
Environmental impact
• Large amount of gases produced present air pollution

problems, in particular SO2 gas  acid rain.
• Dust produced contains heavy metals such as

mercury, lead, cadmium, zinc  health problems.
• Waste water contaminated with:

Insoluble substances, mostly waste sludge (finely ground rock).
Soluble substances (heavy metals, sulphates).
Chemicals from flotation process.
Hydrometallurgy of copper
Advantages
• Much more environmentally friendly than
pyrometallurgy.
• Compared to pyrometallurgy, only a fraction of the
gases liberated into the atmosphere.
• Emissions of solid particles comparatively non-
existent.
Disadvantages
• Large amount of water used,  greater potential for
contamination.
• Waste waters contain soluble metal compounds,
chelating compounds & organic solvents.
The following steps are involved:
1. Ore preparation
2. Leaching
3. Solution purification
4. Metal recovery
1. Ore preparation
• Ore undergoes some degree of comminution
(crushing & pulverisation) to expose the Cu oxides &
sulphides to leaching solution.
1. Ore preparation (cont.)
• Amount of comminution depends on quality of ore:
Higher grade ore – more comminution.
Lower grade ore – less comminution.
(Why??)
• If possible, ore is pre-concentrated; reject ore that
contains very little Cu.
2. Leaching
Definition : The dissolution of a mineral in a solvent, while
leaving the gangue (rock or mineral matter of no value)
behind as undissolved solids.
• Cu is normally leached by one of three methods:

(a) Dump leaching
(b) Heap leaching
(c) Bacterial leaching

2. Leaching (cont.) (a) Dump leaching
• Leaching solution trickled over a dump.

• Runoff solution collected & the Cu recovered from it.
• A slow process that takes months or years to complete.
• Typically only around 60% of the Cu in the dump is
recovered.
2. Leaching (cont.) (b) Heap leaching
• Similar to dump leaching except ore not simply dumped on a

hillside, but is crushed to gravel size & piled onto an artificial
pad.
• After leaching (6 months to 1 year) gangue is removed from
pad, disposed of & replaced with fresh ore.
2. Leaching (cont.)
Leaching reactions
Nature of ore determines if leaching is non-oxidative or
oxidative.
Non-oxidative leaching: No change in oxidation state.
e.g. (1) dissolution of copper sulphate by water:

CuSO4(s) + H2O(l)  Cu2+(aq) + SO42-(aq)
(2) dissolution of alkaline materials by acid:

Cu2(OH)2•CO3(s) + 2H2SO4(aq)  2CuSO4(aq) + CO2(g) + 3H2O(l)
2. Leaching (cont.)
Oxidative leaching: Many ores only soluble once oxidised.
e.g. covellite (CuS) much more soluble if oxidised to CuSO4
CuS(s) + O2(g)  CuSO4(aq)
CLASS EXERCISE : work out which species is oxidised, and
which is reduced, and write out the balanced half reactions for
each.
SOLUTION: CuS  Cu = +2, S = -2
O2 O=0
CuSO4  Cu = +2, O4 = -8, S = +6
S-2  S+6 + 8e- (oxidation)

2O2 + 8e-  4O2- (reduction)
2. Leaching (cont.) (c) Bacterial leaching
• Several bacteria, especially Thiobacilli, are able to
solubilise metal minerals by oxidising ferrous to ferric
iron, as well as elemental sulphur, sulphide, and other
sulphur compounds to sulphate or sulphuric acid.
• 20 to 25% of copper produced in the USA, and 5% of

the worlds copper is obtained by bacterial leaching.
• Very slow process; takes years for good recovery
• But low investment and operating costs.

Thiobacilli
• Are acidotolerant; some grow at pH’s as low as 0.5
• Are tolerant against heavy metal toxicity.
• Are chemolithoautotrophs (C source is CO2 & energy

derived from chemical transformation of inorganic
matter).
Mechanisms
Generalised reaction : M(II)S + 2O2  M2+ + SO42-
• Two mechanisms: (a) indirect mechanism involving

the ferric-ferrous cycle, and (b) direct mechanism
involving physical contact of the organism with the
sulphide mineral.
Mechanisms: Indirect
First step: ferrous sulphate is converted into ferric

sulphate by the action of Acidithiobacillus ferrooxidans:
4FeSO4 + O2 + 2H2SO4  2Fe2(SO4)3 + 2H2O
CLASS EXERCISE : work out which is ferric- and which is

ferrous sulphate, and write out the balanced half reactions for
each.
FeSO4 – SO42-  Fe2+ (ferrous)
2Fe2(SO4)3 – 3 × SO42- = -6, but 2 × Fe Fe3+ (ferric)
2Fe2+  2Fe3+ + 2e- (oxidation)

O2 + 2e-  2O2- (reduction)
• Ferric sulphate is a strong oxidising agent capable of

dissolving a range of sulphide minerals.
• In the case of chalcopyrite:

CuFeS2 + 2Fe2(SO4)3  CuSO4 + 5FeSO4 + 2S
• The elemental S produced by the indirect method can
be converted to H2SO4 by Acidithiobacillus
ferrooxidans:
• The H2SO4 helps maintain the pH at levels favourable

for bacterial growth.
Mechanisms: Direct
• Bacteria actually adheres to the mineral surface prior
to enzymatic attack.
• The mineral is oxidised with oxygen to sulphate and

metal cations without any detectable intermediate
occurring.
• In the case of covellite:
CuS + 2O2  CuSO4

3. Solution Purification
• Leaching reactions not perfectly selective  other
elements in solution as well, not just Cu. These need
to be removed.
• After leaching, Cu in solution can be very dilute. 

need a way to concentrate it.
• Both of these are generally done using ion exchange

processes, the two most common being ion exchange
chromatography, and solvent extraction.
Ion exchange chromatography
• DEFINITION: a solution containing a mixture of metal
ions is contacted with a resin that is insoluble in the
metal-ion solution.
• Ion-exchange resin consists of an inert solid phase to
which labile functional groups are chemically bonded.
• Functional groups can either be acidic (H+) or basic
(OH–) groups that exchange with cations (M+) or
anions (M–), respectively.
• The ion-exchange process is reversible.
Ion exchange chromatography
• Carboxyl groups exchanges the ion it currently holds

(H+) for a Cu2+ ion.
• The Cu2+ is later released by contacting it with a
stripping solution (very high H+ conc.).
3. Solution Purification: Solvent extraction
• DEFINITION: a method to separate compounds

based on their relative solubilities in 2 different
immiscible liquids.
• In industry, this is usually set up as a continuous

process
• Organic + aqueous stream pumped into a mixer.
• Organic (containing an extractant) and aqueous
components mix, and ion transfer occurs between them.
• Once ion transfer is complete (equilibrium), mixture is
allowed to separate.
• Aqueous solution is removed & the organic phase
(containing the Cu2+) is mixed with an aqueous stripping
solution.
• Cu2+ moves back into the aqueous phase, and the two
phases are again allowed to separate.
• The aqueous phase (containing the Cu2+) is removed &
the organic phase is recycled back into the first mixer.
Extractants
• The most successful extractants for copper are of the ortho-
hydroxyoxime type:
OH
OH N
R = alkyl ,phenyl, or H
R R1 = alkyl
1
R
• Function by means of a pH-dependent cation-exchange
mechanism:
Cu2+ + 2HA  CuA2 + 2H+
(where H in HA denotes the replaceable, phenolic proton)
Extractants
• At low pH (1.5 – 2.0) the ortho-hydroxyoxime extractant
complexes the Cu.
• During back-extraction (stripping stage) the pH is lowered

further, releasing the Cu, and regenerating the hydroxyoxime
for recycle to the extraction stage.
• Aqueous feeds (leach solution) typically contain more iron

per litre than copper. For commercial success, the extractant
must  have a greater selectivity for Cu than Fe.
Extractants
• Cu2+ forms square-planar complexes with hydroxyoxime:
O H
R
1
R O N
Cu
1
N O R
R O H
• H-bonding between the oximic H and the phenolic O affords
this 2:1 complex unusual stability.
• The formation constant (K2) for the 2:1 complex is much

greater than for the 1:1 complex.
Extractants
• The tris(salicylaldoximato)iron(III) complex is octahedral, and
no extended planar ring structure is possible between the 3
oxime ligands.
•  stability of Fe(III) complex is less than Cu(II) complex,

which allows the extraction of Cu to be carried out at lower
pH than what is required for efficient Fe extraction.
4. Metal Recovery:
• At this point, the metal needs to be recovered from

solution in the solid form.
• This is either achieved chemically, or

electrochemically.
4. Metal Recovery: Chemical recovery
• Dissolved copper will plate out on an iron surface

according to the following reaction:
Cu2+(aq) + Fe(s)  Fe2+(aq) + Cu(s)
Why??
Reduction half-reactions:
Cu2+(aq) + 2e–  Cu(s) Ered = +0.34 V
Fe2+(aq) + 2e–  Fe(s) Ered = -0.44 V
• Ered for the Cu2+ half-reaction is more positive than for
the Fe2+ half reaction which leads to Cu being
reduced and Fe oxidised.
4. Metal Recovery: Chemical recovery
• Solutions containing dissolved copper are thus run

through a bed of shredded scrap iron, resulting in the
copper ions being plated out as solid Cu on the iron
surface.
• For the process to be efficient, the surface of the

scrap iron must be large.
4. Metal Recovery: Electrochemical recovery
Electrowinning
• An electrochemical process for precipitating metals
from solution.
Electrowinning
• A current is passed from an inert anode through a

liquid leach solution containing the metal so that the
metal is extracted as it is deposited onto the cathode.
• The anode is made out of a material that will not

easily oxidise or dissolve, such as lead or titanium.
Electrorefining
• The anodes consist of unrefined impure metal.
• Current passes through the acidic electrolyte
corroding the anode into the solution.
• Refined pure metal deposited onto the cathodes.
• Metals with a greater Ered than Cu (such as Zn and
Fe) remain in solution.
• Metals with a lower Ered than Cu (Au, Ag) accumulate
as an “anode sludge”  collected & sold for further
refining.
Electrorefining
Summary:
Silicon production
• More difficult to extract Si than either Cu or Fe.
rG /kJ mol-1
Temperature /C
Silicon production
• Silicon of between 96 to 99% purity is achieved by
reduction of quartzite or sand (SiO2, also called silica)
• High temperatures required achieved in an electric arc

furnace.
• Reduction carried out in the presence of excess silica

to prevent accumulation of silicon carbide (SiC) :
SiO2(l) + 2C(s)  Si(l) + 2CO2(g)

2SiC(s) + SiO2(l)  3Si(l) + 2CO(g)
Silicon production
The electric arc furnace
• Silica and carbon fed in
through the top, liquid Si
collected at the bottom.
• Temps of ± 2000K
achieved by an electric
arc burning between
graphite electrodes.
• An arc forms between the charge and the electrodes.
• The charge is heated both by current passing through the charge and
by the radiant energy evolved by the arc.
Silicon production
The electric arc furnace
• Electric arc furnaces require huge amounts of electricity. A mid-

sized furnace would have a transformer rated about 60,000,000
volt-amperes with a secondary voltage between 400 and 900
volts and a secondary current in excess of 44,000 amperes.
Silicon production
Applications
• Si is the 2’nd most abundant element in the earth’s
crust (~28%).
• Principal constituent of natural stone, glass, concrete
& cement.
• Largest application of pure Si (metallurgical grade) is
in the manufacture of Al-Si alloys to produce cast
parts (for automotive industry).
• Important constituent of electrical steel (modifies the
resistivity & ferromagnetic properties).
• Added to molten cast iron to improve its performance
in casting thin sections.
Silicon production
Applications
• 2’nd largest application is in the production of
silicones. These are polymers containing Si-O and Si-
C bonds. Typically heat-resistant, nonstick, and
rubberlike, they are frequently used in cookware,
medical applications, sealants, lubricants, and
insulation.
• Electronics industry – ultra-pure silicon wafers used in

electronic components such as transistors, solar cells,
integrated circuits, microprocessors & various
semiconductor devices.
Silicon production
Purification
• Ultra-pure silicon is required for the production of
semiconductors.
Silicon production
Purification
• Semiconductor-grade Si produced by converting
crude Si to more volatile compounds like SiCl4.
• These are then purified by exhaustive fractional
distillation.
• Reduced back to Si with pure H2.
• Finally, the high-purity Si is melted and large single
crystals are grown by the Czochralski process.
• Electronic grade Si is required to be 99.999999999%
pure!
Silicon production
Purification: The Czochralski process
• Ultra-pure Si (only a few ppm of impurities) is melted in a crucible.
• Dopant impurities (B or
P) can be added to
make n-type or p-type
silicon (influences the
electrical conductivity).
• A seed crystal mounted
on a rod is dipped into
the molten Si.
• Seed crystal rod pulled up & rotated at the same time.
• By carefully controlling the temp gradients, rate of pulling, and

rotation speed, a large single-crystal (called a boule) can be
extracted from the melt.
Silicon production
Silicon production
• The boule is then ground down
to a standard diameter and
sliced into wafers, much like a
salami.
• The wafers are etched and

polished, and move on to the
process line.
• A point to note however, is that due to "kerf" losses (the width
of the saw blade) as well as polishing losses, more than half
of the carefully grown, very pure, single crystal silicon is
thrown away before the circuit fabrication process even
begins!
Silicon production
Electrochemical preparation:
• A new method that uses electrolysis to reduce SiO2 to
elemental Si.
• Advantageous because it avoids the high energy costs

associated with the older carbothermic route, and also
reduces the CO2 emissions considerably.
• SiO2 is usually an insulator, and doesn’t conduct electricity,

but it has been shown that a tungsten wire sealed within a
quartz tube with the tungsten end exposed, can act as a
cathode.
Silicon production
• The anode is usually graphite, and the reduction is carried
out in a solution of molten CaCl2 at around 850 C.
a) SEM of W-SiO2 electrode

before reduction.
b) After reduction.
c) After washing.
d) Side view.
Silicon production
• Conversion of quartz to Si occurs at the three-phase
boundary between the SiO2, the electrolyte, and the flattened
end of the tungsten wire.
• This provides enough impetus for the electrochemistry to

kick in properly as the silica is gradually converted to
conducting silicon.
• This reaction should theoretically propagate through the

silica electrode, but in reality it grinds to a halt very quickly.
• Reason for this is that the molten electrolyte cannot

penetrate through the newly formed Si layer on the surface.
 three-phase boundary formation halted.
Silicon production
• Solution: replace solid quartz electrode with SiO2 powder
pressed into pellets & sintered.
• Resulting electrode porous enough to allow electrolyte to

penetrate deeply into the material.
a) SEM of SiO2 powder

b) reduced Si powder.
Silicon production
Aluminium production
• Most abundant metallic element in the earth’s crust.
• But, extremely rare in its free form.
• Once considered as a precious metal more valuable

than gold!
• Al is a highly reactive metal that forms strong bonds

with O.
• Requires a large amount of energy to extract from

Al2O3.
• Cannot be reduced directly by carbon since Al is a
stronger reducing agent than C.
• Must therefore be extracted by electrolysis.
• Aluminium production involves two steps: 1) purifying
Al2O3 from bauxite (the Bayer process) and 2)
converting Al2O3 to metallic Al (The Hall-Heroult
process).
• Primary Al ore is bauxite, which consists of:
Gibbsite - Al(OH)3 (most extractable form)
Boehmite - AlO•OH (less extractable than Gibbsite)
Diaspore - αAlO•OH (difficult to extract)
The Bayer process: Step 1: Dissolution
• The hydrated aluminium oxides are first selectively
dissolved from bauxite:
Al(OH)3 + NaOH  NaAlO2 + 2H2O (Gibbsite dissolution)
AlO•OH + NaOH  NaAlO2 + H2O (Boehmite dissolution)
• An undesirable side reaction is the formation of “red

mud”, which occurs when Al(OH)3 reacts with
dissolved Kaolinite clay:
5Al2Si2O5(OH)4 + 2Al(OH)3 + 12NaOH  2Na6Al6Si5O17(OH)10 + 10H2O
• Red mud formation consumes dissolved Al and 

represents a Al loss.
The Bayer process: Step 2: Solid-Liquid Separation
• The digested bauxite now consists of 1 liquid and 2
solid components:
Caustic liquid soln. with dissolved Al.
Undissolved coarse material (sand).
Precipitated fines (red mud).
• Sand (mainly undissolved silicates) easily removed
since they settle very rapidly.
• The red mud is removed by adding a flocculent to
increase the settling rate.
• The Al content of the red mud is recovered & forms
part of the liquid layer.
The Bayer process: Step 3: Precipitation
• The remaining solution is supersaturated, containing
around 100-175 grams of dissolved Al2O3 per litre.
• Al(OH)3 is precipitated out by adding seed crystals

since Al(OH)3 doesn’t crystallise out easily on its own.
• Once the crystals have reached the desired size, they

are removed, washed, and filtered.
• The spent liquor is reheated, recausticised and

recycled.
The Bayer process: Step 4: Calcination
• Wet crystals of Al(OH)3, obtained from the
precipitation step are dried by heating to around 1300
– 1500 C.
• This process also converts the Al(OH)3 to Al2O3:

2Al(OH)3  Al2O3 + 3H2O
The Bayer process: Problems
• Problems result from the coordination chemistry of Al
in basic solutions. Generally accepted structures:
• Leads to extensive H-bonding between aluminate ion

& solvent, which in turn leads to high viscosity of these
solutions.
• In turn leads to problems with materials handling &
heat exchange.
The Bayer process: Problems
• In addition, the inertness of Al(III) leads to slow rates
of crystallisation, requiring large vessels & large
volumes of circulating solution & seed material.
The Hall-Heroult process:
• Reactive metals (e.g. Mg and Na) can be produced by
electrolysing a molten chloride salt of the metal.
• Not the case for AlCl3 since it sublimes rather than
melts.
• Even under sufficient pressure, molten AlCl3 is an
electrical insulator & cannot be used as an electrolyte.
Would have to be dissolved in a conductive salt (NaCl
or KCl).
• Commercially viable production of Al only commenced
once the use of cryolite (Na3AlF6) was discovered.
• Cryolite is electrically conductive, and dissolves Al2O3.
• Anhydrous Al2O3 melts at over 2000C which is too
high to be used as a molten medium for electrolytic
reduction of Al.
• Al2O3 dissolved in cryolite has a m.p. of 1012C & is a

good electrical conductor.
• Graphite rods are used as anodes & are consumed in

the electrolytic process.
• The cathode is a steel vessel, lined with graphite.

• The electrode reactions are as follows:
Anode: C(s) + 2O2-(l)  CO2(g) + 4e-
Cathode: 3e- + Al3+(l)  Al(l)
CLASS EXERCISE : Write out the balanced overall reaction
4Al3+(l) + 6O2-(l) + 3C(s)  4Al(l) + 3CO2(g)
CLASS EXERCISE : Calculate the mass of Al that will be

produced in 1.00 hr by the electrolysis of molten AlCl3, using a
current of 10.0 A.
• Step 1: calculate the number of coulombs (C) from the
current (I) and the time (t):
Q=I×t
= 10.0 A × 3600 s
= 3.60 × 104 C
• Step 2: find the number of moles of electrons:
Q 3.60 104 C
n  -1
 0.373 mol electrons
F 96500 C mol
F (Faraday constant) = magnitude of electric charge per mole

of electrons.
• Step 3: find the mass of Al produced:
3 mole of electrons needed to produce 1 mol of Al:
3e- + Al3+(l)  Al(l)
 Number of mol Al = 0.124
Mr Al = 26.98 g mol-1
 mass Al = 26.98 g mol-1 × 0.124 mol
= 3.34 g Al
• Electrolytic reduction of Al is costly (3 e- required for
every atom of metallic Al reduced).
• The electrical voltage used is only around 5.25 V, but

the current required is very high, typically 100,000 to
150,000 A or more!
• Electrical power is the single largest cost in Al

production,  Al smelters are typically located in areas
with inexpensive electric power, like S.A.
Pyrometallurgy of iron
• Still the most important pyrometallurgical process
economically.
• The most important sources of iron are hematite

(Fe2O3) and magnetite (Fe3O4).
• Prehistorically, iron was prepared by simply heating it

with charcoal in a fired clay pot.
• Today, the reduction of iron
oxides to the metal is
accomplished in a blast
furnace.
Blast furnace:
1) Hot gas blast
2) Melting zone
3) Reduction of FeO
4) Reduction of Fe2O3
5) Pre-heating zone
6) Feed of ore,
limestone + coke
7) Exhaust gases
8) Column of ore, coke
+ limestone
9) Removal of slag
10) Tapping of molten pig iron
11) Waste gas collection
• The iron ore, limestone, and coke are added to the
top of the furnace.
• Coke is coal that has been heated in an inert
atmosphere to drive off volatile components (~ 80 –
90% C).
• Coke is the “fuel”, producing heat in the lower part of
the furnace. Is also the source of the reducing gases
CO & H2.
• Limestone (CaCO3) serves as the source of CaO
which reacts with silicates & other impurities in the ore
to form slag.
Slag:
• Most rocks are composed of silica (SiO2) and silicates
(SiO32-) & are almost always present in the ore.
• These compounds don’t melt at the furnace

temperature & would eventually clog it up.
• An important chemical method to remove these is by
use of a flux which combines with the silica & silicates
to produce a slag.
• Slag collects at bottom of furnace & doesn’t dissolve
in the molten metal.
Slag:
• The heat of the furnace decomposes the limestone to
give calcium oxide.
• CaO (a basic oxide) reacts with silicon dioxide to give

calcium silicate.
CaCO3(s)  CaO(s) + CO2(g)
CaO(s) + SiO2(s)  CaSiO3(l)
• Slag helps protect the molten iron from re-oxidation.
• Slag is used in road making, and can also be

combined with cement.
• Air is blown into the bottom of the furnace, and
combusts with the coke to raise the furnace temp up
to 2000C :
2C(s) + O2(g)  2CO(g) H = -221 kJ
• H2O in the air also reacts with the coke:

C(s) + H2O(g)  CO(g) + H2(g) H = +131 kJ
• Since this reaction is endothermic, if the blast furnace

gets too hot, water vapor is added to cool it down
without interrupting the chemistry.
• Molten iron is produced lower
down the furnace & removed.
• Slag is less dense than iron &

can be drained away.
• The iron formed (called pig iron)

still contains around 4-5% C, 0.6-
1.2% Si, 0.4-2.0% Mn + S and P
and needs to be further
processed.
• At around 250C (top of the furnace), limestone is
calcinated:
CaCO3(s)  CaO(s) + CO2(g)
• Also at the top of the furnace, hematite is reduced:
3Fe2O3(s) + CO(g)  2Fe3O4(s) + CO2(g)
• Reduction of Fe3O4 occurs further down the furnace

(~700C):
Fe3O4(s) + CO(g)  3FeO(s) + CO2(g)
• Near the middle of the furnace (1000C) Fe is
produced:
FeO(s) + CO(g)  Fe(s) + CO2(g)
Cast iron
• Cast iron is made by remelting pig iron & removing
impurities such as phosphorous and sulphur.
• The viscosity of cast iron is very low, & it doesn’t
shrink much when it solidifies.
•  ideal for making castings.
• BUT, it is very impure, containing up to 4% carbon.
This makes it very hard, but also very brittle.
• Shatters rather than deforms when struck hard.
• These days cast iron is quite rare, often being
replaced by other materials.
Steelmaking
• Pig iron is brittle, and not directly very useful as a
material.
• Typically, pig iron is drained directly from the blast
furnace (referred to as hot metal), and transported to
a steelmaking plant while still hot.
• The impurities are removed by oxidation in a vessel
called a converter.
• The oxidising agent is pure O2 or O2 mixed with Ar.
• Air can’t be used as N2 reacts with iron to form iron
nitride which is brittle.
Steelmaking
• O2 blown directly into molten
metal.
• Reacts exothermically with
C, Si + other impurities.
• C & S expelled as CO and
SO2 gas.
• Si oxidised to SiO2 &
incorporates into the slag
layer.
• Once oxidation complete,
Iron converter contents poured out &
various alloying elements
added to produce steels.
Types of iron & steel
• Wrought iron – iron with all the C removed. Soft &
easily worked with little structural strength. No longer
produced commercially.
• Mild steel – iron containing around 0.25% C. Stronger

& harder than pure iron. Has many uses including
nails, wire, car bodies, girders & bridges, etc.
• High carbon steel – contains around 1.5% C. Very

hard, but brittle. Used for things like cutting tools, and
masonry nails.
Types of iron & steel
• Stainless steel – iron mixed with chromium and nickel.
Resistant to corrosion. Uses include cutlery, cooking
utensils, kitchen sinks, etc.
• Titanium steel – iron mixed with titanium. Withstands

high temperatures. Uses include gas turbines,
spacecraft parts, etc.
• Manganese steel – iron mixed with manganese. Very

hard. Uses include rock-breaking machinery, military
helmets, etc.
The thermite reaction
• Aluminium metal can reduce Iron(III) oxide (Fe2O3) in

a highly exothermic reaction.
• Molten iron is produced at around 3000C.
• Reaction used for thermite welding, often used to join

railway tracks.
Fe2O3(s) + 2Al(s)  2Fe(s) + Al2O3(s)

Fe2O3(s) + 2Al(s)  2Fe(l) + Al2O3(s)
CLASS EXERCISE : calculate the thermal energy that is
released in the reaction.
Component Hfo (kJ/mol)
Fe2O3(s) -822.2
Al(s) 0
Al2O3(s) -1,669.8
Fe(s) 0
Horxn = (1 mol)(HfoAl2O3) + (2 mol)(HfoFe) - (1 mol)(HfoFe2O3) - (2 mol)(HfoAl)
Horxn = (1 mol)(-1,669.8 kJ/mol) + (2 mol)(0) - (1 mol)(-822.2 kJ/mol) - (2mol)(0 kJ/mol)
Horxn = -847.6 kJ mol-1 Exothermic!

Electrowinning of iron
The Pyror process:
• Studies into iron extraction by electrowinning from
sulphate solutions were first carried out around 50
years ago, then subsequently forgotten.
• May become important again in the future as new,

more environmentally friendly methods are sought for
steelmaking.
The Pyror process:
• First step is to convert iron pyrite (FeS2) into an acid
soluble form (FeS). Achieved by either calcining at
800 to 900 C to expel a loosely-bound S, or by
smelting in an electric furnace.
• Step 2 is a leaching step using H2SO4 to extract iron

from FeS:
FeS(s) + H2SO4(l)  FeSO4(l) + H2S(g)
• Step 3: before entering the electrowinning cells, the
solution is purged with air to remove any remaining
H2S.
The Pyror process:
• Step 4: Electrolysis. Iron is reduced and deposited on
the cathode, while O2 is evolved, and H2SO4 is
regenerated at the anode. More specifically:
At the cathode:
Fe2+ + 2e-  Fe(s)
2H+ + 2e-  H2(g)
Fe3+ + e-  Fe2+
At the anode:
SO42- + H2O  H2SO4 + 1/2O2 + 2e-
Fe2+  Fe3+ + e-
The Pyror process:
The Pyror process:
• The process was shown to
be quite efficient. During a 2
year pilot-plant project, a
quantity of iron close to 150
tonnes was produced.
• Electrolysis was run for several weeks before

stripping was performed, resulting in deposits of
13mm or more in thickness.
The Pyror process:
Gold extraction
Gold mining Historical:
• Panning – sand and gravel
containing gold is shaken around
with water in a pan. Gold is much
denser than rock, so quickly
settles to the bottom of the pan.
Gold extraction
Gold mining Historical:
• Sluicing – water is channelled to
flow through a sluice-box. Sluce-
box is essentially a man-made
channel with riffles (barriers) at the
bottom. Riffles create dead-zones
in the water current which allows
gold to drop out of suspension.
• Sluicing and panning results in the direct recovery of

small gold nuggets and flakes.
Gold extraction
Gold mining Modern methods:
• Hard rock mining – used
to extract gold encased in
rock. Either open pit
mining or underground
mining.
Gold extraction
Gold ore processing Gold cyanidation:
• The most commonly used process for gold extraction.
• Used to extract gold from low-grade ore.
• Gold is oxidised to a water-soluble aurocyanide

metallic complex.
• In this dissolution process, the milled ore is agitated

with dilute alkaline cyanide solution, and air is
introduced:
4Au(s) + 8NaCN(l) + O2(g) + 2H2O(l)  4NaAu(CN)2(l) + 4NaOH(l)
Gold extraction
• At a slurry concentration of around 50% solids, the

slurry passes through a series of agitated mixing tanks
with a residence time of 24 hrs.
• The gold-bearing liquid is then separated from the

leached solids in thickener tanks or vacuum filters &
the tailings are washed to remove Au and CN- prior to
disposal.
Gold extraction
• The aurocyanide complex has an exceptionally high

stability constant, 2 [Au(CN)2]- = 2 × 1038.
• This high stability constant means that dissolution can

be achieved even in the presence of considerable
amounts of other metals (Cu, Zn, and Ni).
• At this point, the dissolved Au needs to be recovered

from the cyanide solution. Two methods commonly
used to achieve this are 1) the Carbon in pulp
process, and 2) the Merrill-Crowe process.
Gold extraction
Gold ore processing Heap Leaching
• Is an alternative to the agitated leaching process.

• Drastically reduced gold recovery costs of low grade
ore.
• Ore grades as low as 0.3 g per ton can be
economically processed by heap leaching.
Gold extraction
Gold ore processing Heap Leaching
• Generally requires 60 to 90 days for processing ore

that could be leached in 24 hrs in a conventional
agitated leach process.
• Au recovery is around 70% as compared with 90% in
an agitated leach plant.
• BUT, has gained wide favour due to vastly reduced
processing costs.
• Frequently, mines will use agitated leaching for high-
grade ore & heap leaching for marginal grade ores
that would otherwise be considered waste rock.
Gold extraction
1) Carbon in pulp – overview:
• Dissolved aurocyanide is mixed with free activated
carbon particles in solution and agitated in leach tanks.
• The carbon particles are much larger than the ground
ore particles.
• Gold has a natural affinity for C, and the aurocyanide
complex is adsorbed onto the C.
• The coarse C particles with bound [Au(CN)2]- are then
removed by screening using a wire mesh. Finely ground
ore passes through the mesh.
Gold extraction
1) Carbon in pulp – details:
• On completion of cyanidation, pregnant pulp is

transferred to Carbon In Pulp (CIP) process.
• Pregnant pulp passed through a number of tanks (5 or
6) in series. Tanks are mechanically stirred.
• Granulated carbon is pumped counter-current to the
pulp through the tanks.
• In the final tank, fresh, or barren carbon comes into
contact with low-grade or tailings solution.
Gold extraction
1) Carbon in pulp – details:
• In this tank, the barren carbon has a high activity, and

can remove trace amounts of Au < 0.01 mg / L.
• As the carbon passes through the tanks, it collects

increasing quantities of Au from the solution. This is
termed loading.
• Typically, concentrations as high as 4000 to 8000 g Au /

ton of C can be achieved on the final loaded C.
Gold extraction
1) Carbon in pulp
• The loaded carbon is separated from the pulp in the final

tank & transferred to the elution circuit.
• Barren pulp is dewatered (to recycle water & remove
cyanide for reuse in the process).
• In the elution circuit, the loaded carbon is treated with a
hot cyanide & caustic solution to remove the Au.
• The barren carbon is reactivated & recycled for use in
the process.
Gold extraction
1) Carbon in pulp
• The cyanide & caustic solution is transferred to an
electrowinning circuit where the Au is plated out onto
steel wool.
• The Au-plated steel wool is transferred to the smelting

circuit to produce gold bullion.
Gold extraction
Carbon in pulp
Gold extraction
2) Merrill-Crowe process
• Traditional method for Au recovery from pregnant

cyanide solutions.
• Once dissolution of Au is complete, the remaining rock

pulp if filtered off through various filters &
diatomaceous earth to produce a sparkling clear
solution.
• O2 is removed from the clarified solution by passing

the solution through a vacuum deaeration column.
Gold extraction
2) Merrill-Crowe process
• Zinc dust is then added to the cyanide solution to

chemically reduce the gold to the metal.
• The metallic gold is then filtered out & refined.

Extraction Metallurgy C B Perry 123s

Uploaded by

Copyright:

Available Formats

Extraction Metallurgy C B Perry 123s

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Extraction Metallurgy C B Perry 123s

Uploaded by

Copyright:

Available Formats

Extraction Metallurgy

Part 2: Case studies

Dr. C.B. Perry (C306)

• Hydrometallurgical processes – ion exchange processes,

• Iron – Pyrometallurgy and the blast furnace.

• Silicon – The electric arc furnace. Purification by the Czochralski

• Aluminium – Electrolytic reduction.

• The siderophiles – The extraction of Au and the Pt group metals

2. Roasting: a metallurgical treatment involving gas-

3. Smelting: a melting process which separates the

4. Refining: treatment of a crude metal product to improve its

Most common source of Cu ore is the mineral

Other important ores include:

• Ore then introduced into a water bath where air is

• Finely divided hydrophobic ore particles latch on to the

• The remaining material (sand particles & other

1) Remove part of the sulphur.

2) Convert iron sulphides into iron oxide and iron

3) To pre-heat the concentrate to reduce amount of

• Smelting is carried out at around 1200C, usually with a

FeS(l) + 6CuO(l) → 3Cu2O(l) + FeO(l) + SO2(g)

• The sulphur is removed by selective oxidation of the

• Converting is carried out in two stages: 1) an iron

• The oxidized Fe and Si form a slag (insoluble in

• The end product is around 98.5% pure & is known as

• The anodes (cast from blister copper) are placed into

• Thin sheets of highly pure Cu serve as the cathodes.

• Application of a suitable voltage causes oxidation of

• Cu2+ ions migrate through the electrolyte to the

• Metallic impurities more active then Cu are oxidized at

• Large amount of gases produced present air pollution

• Dust produced contains heavy metals such as

• Waste water contaminated with:

• Cu is normally leached by one of three methods:

(b) Heap leaching

(c) Bacterial leaching

• Leaching solution trickled over a dump.

• Similar to dump leaching except ore not simply dumped on a

e.g. (1) dissolution of copper sulphate by water:

(2) dissolution of alkaline materials by acid:

S-2  S+6 + 8e- (oxidation)

• 20 to 25% of copper produced in the USA, and 5% of

• Very slow process; takes years for good recovery

• But low investment and operating costs.

• Are acidotolerant; some grow at pH’s as low as 0.5

• Are tolerant against heavy metal toxicity.

• Are chemolithoautotrophs (C source is CO2 & energy

Generalised reaction : M(II)S + 2O2  M2+ + SO42-

• Two mechanisms: (a) indirect mechanism involving

First step: ferrous sulphate is converted into ferric

CLASS EXERCISE : work out which is ferric- and which is

2Fe2+  2Fe3+ + 2e- (oxidation)

• Ferric sulphate is a strong oxidising agent capable of

• In the case of chalcopyrite:

• The H2SO4 helps maintain the pH at levels favourable

• The mineral is oxidised with oxygen to sulphate and

• In the case of covellite:

CuS + 2O2  CuSO4