ITB-KEOH-2017-003 - Section V - Annex D (VII) - NYANDIWA HC DRAWINGS

ANNEX D-(i)
ARCHITECTURAL DESIGNS AND DRAWINGS

(Architectural Drawing)
Operational excellence for results that matter
client
KENYA
project
Infrastructure Upgrade to Nyandiwa

Health Centre, Homabay County.
June 2016
N
East Africa Hub (EAH), Nairobi

UNOPS Building, UN lane,
Off UN Avenue P.O. Box
783, Village Market, 00621
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in
centimetres, unless otherwise
stated.
2. All dimensions to be checked and

confirmed on site before
commencement of any work.
3. Written dimensions overrides

scaled dimensions,thus all
dimensions are
NEW PUMP HOUSE to be read and not at any time scaled
from the drawing.
4. Any discrepancy to be reported to

the Engineer promptly before
proceeding.
NO REVISION DATE APPR.
.
CLIENT
UNICEF
PROJECT
INFRASTRUCTURE UPGRADE
TO NYANDIWA HEALTH CENTRE
HOMABAY COUNTY.
DRAWING TITLE
GOOGLE LOCATION MAP
DESIGN SERVICES UNIT

DRAWN BY Atego
CHECKED BY PhilipM.
APPROVED BY MoyizE.
JUNE 2016
LEGEND DATE
PROJECT NUMBER:
EXISTING BUILDINGS DSU-UNICEF-15-19

DRAWING NUMBER:
PROPOSED LOCATION OF NEW BUILDINGS AR-000-1

TENDER DRAWINGS
COPYRIGHT RESERVED
THIS DESIGN AND DETAIL ARE,
GOOGLE LOCATION - RACHUONYO SUB-COUNTY HOSPITAL AND AT ALL TIMES THE EXCLUSIVE
PROPERTY OF THE UNOPS/EAH,NAIROBI
AND CANNOT BE USED OR REPRODUCED
WITHOUT WRITTEN CONSENT.
N Operational excellence for results that matter

Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in centimetres,
LAKE unless otherwise stated.

confirmed on site before commencement
of any work.
3. Written dimensions overrides scaled

dimensions,thus all dimensions are
to be read and not at any time scaled
NEW from the drawing.
PUMP HOUSE
4. Any discrepancy to be reported to the
Engineer promptly before proceeding.

.
CLIENT
EXISTING
ELEVATED
WATER TANK UNICEF
TO BE DEMOLISHED
PROJECT
HOMABAY COUNTY.
DRAWING TITLE
EXISTING SOURCE
OF POWER LOCATION SITE PLAN

DRAWN BY Atego
LEGEND CHECKED BY PhilipM.

APPROVED BY MoyizE.
EXISTING BUILDINGS
DATE JUNE 2016
PROPOSED LOCATION OF NEW BUILDINGS PROJECT NUMBER:
DSU-UNICEF-15-19
PROPOSED POWER CABLE ROUTE AND LENGTH DRAWING NUMBER:
AR-000-2
TENDER DRAWINGS
COPYRIGHT RESERVED
SITE PLAN - RACHUONYO SUB-COUNTY HOSPITAL AND AT ALL TIMES THE EXCLUSIVE
Catladder to SEs details Operational excellence for results that matter
Catladder
to SEs details East Africa Hub (EAH), Nairobi
900 UNOPS Building, UN lane,
4No 100x100x4mm SHS
Columns to SEs details Nairobi, Kenya.
4No 100x100x4mm SHS
Columns to SEs details GENERAL NOTES
3,200
3,200
stated.
4mm thick 4mm thick
CHEQUER plate CHEQUER plate
90cm high 90cm high commencement of any work.
MS railing MS railing
scaled dimensions,thus all dimensions
are
to be read and not at any time scaled from
3,270 3,270
the drawing.
7,440
WATER TANK PLAN scale 1:50 the Engineer promptly before
proceeding.
NO. REVISION DATE APPR.
90cm high MS 90cm high

railing 10,000 ltr 10,000 ltr
plastic water plastic water MS railing
4mm tank tank 4mm thick
thick CHEQUER detail A CHEQUER plate
plate
CLIENT
UNICEF
2,000
2,000
PROJECT
TO RACHUONYO SUB COUNTY
HOSPITAL
HOMABAY COUNTY.
DRAWING TITLE
2,000
6,000
6,000
2,000
WATER TANK
20 dia 90cm high
MS baluster welded
to MS plate DESIGN SERVICES UNIT
4mm thick chequer

DRAWN BY Atego
plate
90
CHECKED BY PhilipM.
MS plate bolted APPROVED BY MoyizE.

onto 4mm chequer DATE JUNE 2016
plate
2,000
2,000
PROJECT NUMBER:
DSU-UNICEF-15-19
70x70x5mm RHS DRAWING NUMBER:
to SEs details
AR-104
F.G.L F.G.L
0.000 0.000 TENDER DRAWINGS
150
150
150
150
100x100x5mm RHS
to SEs details column footing COPYRIGHT RESERVED
to s.e detail THIS DESIGN AND DETAIL ARE,
DETAIL A AND AT ALL TIMES THE EXCLUSIVE
1:5 WATER ELEVATION PLAN scale 1:50 PROPERTY OF THE UNOPS/EAH,NAIROBI

WITHOUT WRITTEN
CONSENT.
2 coats of weather proof
acrylic paint on 900mm high solid
Section Section
Elevation Elevation concrete block walling
04 01 04 01 Operational excellence for results that matter
B B 1
A A East Africa Hub (EAH), Nairobi
2
2,200
200 2,000 200 UNOPS Building, UN lane,
BOTTOM Off UN Avenue P.O. Box
OF BEAM 783, Village Market, 00621
1 Roof pitch 6 deg. 26g IT5 roofing 1 Nairobi, Kenya.
sheets on steel
200
structure to S.E.'s details 100mm high
pump base GENERAL NOTES
to S.E.'s details
VBW 01 WATER VBW 01
clay vent blocks
to selection
PUMP
2,200
2,200
Elevation Elevation stated.
2,100
05 05
Elevation Elevation ROOM
2,000
1,600
commencement
03 03 of any work.
outline of outline of
wall below roof above GROUND
FLOOR F.F.L. 3. Written dimensions overrides
500
2 SD 01 2 SD are
01 to be read and not at any time scaled from
200
150
the drawing.
GROUND
LEVEL 4. Any discrepancy to be reported to
Elevation Elevation
Floor PlanRoof Plan 02 Section Floor Plan 02 Elevation 03 the Engineer promptly before
proceeding.
Section
1:50 1:50 NO. REVISION DATE APPR.
1:50 01 01
Elevation 05 (Similar
but handed)
6.0 deg.
2 coats of weather proof
acrylic paint on 900mm high solid Roof pitch 6 deg. 26g IT5 roofing
concrete block walling sheets on steel
CLIENT
2 1 A B B structure to S.E.'s details
A
UNICEF
Roof pitch 6 deg. 26g IT5 roofing 2,200
sheets on steel 2,200 2,200
DETAIL A
structure to S.E.'s details DETAIL B
BOTTOM BOTTOM BOTTOM

OF BEAM OF BEAM 2,000
OF BEAM PROJECT
RC lintol to SE
300
300
SD 01
.
details
HOMABAY COUNTY.
clay vent blocks
MS grille 2 coats of weather proof
to selection
door acrylic paint on 900mm DRAWING TITLE
1,600
high solid concrete
2,100
2,100
2,100
2,100
block walling
MS still grille door .
PUMP HOUSE
10x10mm solid
.
welded bars
GROUND GR OUND GROUND
50mm floor finish on 150mm r.c. slab FLOOR F.F.L. FLOOR F.F.L. DETAIL C FLOOR F.F.L. DESIGN SERVICES UNIT
on
500
1000g polythene d.p.m on 50mm .

blinding on 250mm min. hardcore with DRAWN BY Atego
anti termite treatment Gravel
150
150
150
150
PhilipM.
150
dpc CHECKED BY
dpc GROUND GROUND GROUND
LEVEL LEVEL LEVEL APPROVED BY MoyizE.
Elevation 02 Elevation 04 DATE JUNE 2016
r.c. strip foundations PROJECT NUMBER:
to S.E.'s details
DSU-UNICEF-15-19
Section 1-1 DRAWING NUMBER:
AR-105
TENDER DRAWINGS
COPYRIGHT RESERVED
AND AT ALL TIMES THE EXCLUSIVE
AND CANNOT BE USED OR
REPRODUCED WITHOUT WRITTEN
CONSENT.
Off UN Avenue P.O. Box 783,
Village Market, 00621
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in centimetres,
150mm Z purlins to unless otherwise stated.
SEs details 2. All dimensions to be checked and
of any work.
Pitch: 6º 26g IT5 roofing sheets fixed
130x50x2mm Z purlins at 3. Written dimensions overrides scaled
to Z purlins with J bolts to SE's details Pitch: 6º 26g IT5 roofing sheets fixed to
850mm centres to SEs details dimensions,thus all dimensions are
Z purlins with J bolts to SE's details to be read and not at any time scaled from
the drawing.
Pitch: 6º 26g IT5 roofing sheets on steel 4. Any discrepancy to be reported to the
trusses to s.e details 150mm Z purlins Engineer promptly before proceeding.
to SEs details
50x50x4mm RHS rafter to
-
S.E's details
CLIENT
300mm RC linto-
l to SEs details UNICEF
F.F.L 2400mm
200mm thick -
walling
F.F.L 2400mm
PROJECT
TO RACHUONYO SUB COUNTY
HOSPITAL
HOMABAY COUNTY.
DRAWING TITLE
300mm RC linto-
l to SEs details
PUMP HOUSE ROOF DETAILS
eave detail B
detail A scale 1:10 DRAWN BY Atego
scale 1:10 CHECKED BY PhilipM.

APPROVED BY MoyizE.
DATE JUNE 2016
PROJECT NUMBER:
DSU-UNICEF-15-19
DRAWING NUMBER:
AR-105-a
TENDER DRAWINGS
COPYRIGHT RESERVED
THIS DESIGN AND DETAIL ARE, AND
AT ALL TIMES THE EXCLUSIVE
N
2,000
2,000
r.c lintel Operational excellence for results that matter

Nairobi, Kenya.
GENERAL NOTES
clay vent blocks
1,600
to selection
stated.
2,100
+2.10 commencement of any work.
Quantity - 1no.
SD 01 3. Written dimensions overrides
scaled dimensions,thus all
dimensions are
the drawing.
N 4. Any discrepancy to be reported to the

2,000
500
GROUND Engineer promptly before proceeding.
10 30 960 20 20 920 30 10 FLOOR
F.F.L.
10

10x10mm RHS burglar bars
27
150
150
decorated in oil paint
egg shell finish
GROUND +2.10
LEVEL Typical window elevation
VBW 01Quantity - 2no. scale 1:20
853
+0.50
MS grille
door
12mm dia. slide bolt 300mm CLIENT

long with hasp and staple to
UNICEF
280 20
receive heavy duty padlock

2,100
20x20x3mm RHS
20
r.c lintel PROJECT
DETAIL C TO NYANDIWA HEALTH CENTRE
HOMABAY COUNTY.
870
GROUND DRAWING TITLE

FLOOR F.F.L. 3no. heavy duty hinges
locally manufactured clay vent blocks to
s.e specifications PUMP HOUSE DOOR AND
VENT BLOCK DETAILS
SD 01 elevation scale 1:25 DESIGN SERVICES UNIT

DRAWN BY Atego
CHECKED BY PhilipM.
APPROVED BY MoyizE.
pcc window cill
DATE JUNE 2016
10x10mm solid walling PROJECT NUMBER:
welded bars OUTSIDE DSU-UNICEF-15-19

INSIDE
DRAWING NUMBER:
Clay vent block Section AR-105-b
N-N scale 1:10 TENDER DRAWINGS
DETAIL C scale 1:5

COPYRIGH
T
RESERVED
THIS
DESIGN AND
DETAIL ARE,
AND AT ALL
TIMES THE
EXCLUSIVE
PROPERTY OF
THE
UNOPS/EAH,NAIR
OBI AND CANNOT
BE USED OR
REPRODUCED
WITHOUT
WRITTEN
CONSENT.
200
20cm thick block walls Operational excellence for results that matter
for Inspection chamber East Africa Hub (EAH), Nairobi
200 600 200 Off UN Avenue P.O. Box
V V Nairobi, Kenya.
450
GENERAL NOTES
line of cast iron 1. All dimensions are in centimetres,
unless otherwise stated.
cover above 2. All dimensions to be checked and
of any work.
200 3. Written dimensions overrides scaled
from
the drawing.


.
direction of flow
CLIENT
Inspection Chamber UNICEF

detail plan scale 1:10 PROJECT
200 600 200 HOMABAY COUNTY.
metal cover on angle section DRAWING TITLE
frame to site Eng's approval ELECTRICAL INSPECTION

CHAMBER

Detail 'W' DRAWN BY Atego
CHECKED BY PhilipM.
6"diameter sleave UPVC
600
APPROVED BY MoyizE.
pipe beyond DATE JUNE 2016
PROJECT NUMBER:
DSU-UNICEF-15-19
20cm thick block walls DRAWING NUMBER:
for Inspection chamber AR-106

100
TENDER DRAWINGS
COPYRIGHT RESERVED
10cm thick PROPERTY OF THE UNOPS/EAH,NAIROBI

concrete base
Section V-V scale 1:10
MECHANICAL DESIGNS AND DRAWINGS
PROJECT.
INFRASTRUCTURE UPGRADE TO
NYANDIWA HEALTH CENTRE
HOMABAY COUNTY.
18 SEPTEMBER 2016
UNOPS

Off Avenue P.O. Box 783,
DRG. No. DRAWING TITLE Nairobi, Kenya.
GENERAL NOTES
DSU-UNICEF-15-19-M001 MECHANICAL SERVICES DRAWINGS LIST
DSU-UNICEF-15-19-M002 MECHANICAL SERVICES LEGEND & GENERAL NOTES
DSU-UNICEF-15-19-M003 SITE PLAN WATER RETICULATION
DSU-UNICEF-15-19-M004 WATER DISTRIBUTION SCHEMATIC NO. REVISION DATE APPR.
CLIENT
UNICEF
PROJECT
INFRASTRUCTURE
UPGRADE TO
NYANDIWA HEALTH
CENTRE HOMABAY
COUNTY .
DRAWING TITLE
MECHANICAL SERVICES
DRAWINGS LIST

DRAWN BY O.S
CHECKED BY NKM
APPROVED BY MoyizE.
DATE 18 SEPTEMBER '2016

PROJECT NUMBER:
DSU-UNICEF-15-19
DRAWING NUMBER:
DSU-UNICEF-15-19-M001
TENDER DRAWINGS
COPYRIGHT RESERVED
CONSENT.
UNOPS
NOTES East Africa Hub (EAH), Nairobi
LEGENDS
1 PD Pipe Drop Off Avenue P.O. Box 783,
1. The copyright of this drawing is vested in the Engineers and it must not Village Market, 00621
2 PR Pipe Rise. be used or reproduced without their express authority. Nairobi, Kenya.
3 H/L High Level. GENERAL NOTES

2. All mechanical services drawing shall be read in conjuction with the
4 NC Normally Closed Isolation Valve Architects drawing.Any discrepancies MUST be reported to the
5 BFV - Ball Float Valve. Engineers.
6 IV - Isolation Valve.
3. All mechanical services drawings must be checked against existing site
7 NRV - Non-Return Valve. conditions and any discrepancy reported to the Engineers.
8 WM - Water Meter.
4. All dimensions are internal diameters and are in millimetres unless
9 Booster Pump-set
otherwise indicated. NO. REVISION DATE APPR.
10 RWDP Rain Water Down Pipe

Vent Pipe.
5. This drawing should only be used for the specific services intended.
11 VP
12 SVP Soil Vent Pipe. 6. This drawing shows the design intent only. The contractor shall be
13 NO Normally Open Isolation Valve responsible for the full co-ordination of the services indicated on this CLIENT
and all other services drawings.

14 F/A From Above. UNICEF
15 T/A To Above. 7. Final access and setting out of services shall be agreed between the
PROJECT
16 F/B From Below. architect and the contractor INFRASTRUCTURE

UPGRADE TO NYANDIWA
HEALTH CENTRE
17 T/B To Below. 8. Where public health services pass through fire compartmentation ceiling HOMABAY COUNTY
18 RE Rodding Eye. voids, floor voids and structural walls the contractor shall sleeve/seal the DRAWING TITLE
opening with an acoustic and fire sealant approved by the architect. MECHANICAL SERVICES
19 FT-Floor Trap. LEGEND & GENERAL NOTES
20 IC - Inspection Chamber 9. All drainage pipe work shall be in uPVC,heavy duty DESIGN SERVICES UNIT
21 GT - Gully Trap DRAWN BY O.S
10. Drainage pipework slopes at 1:100

22 4.5Kg CO2fire extinguisher. CHECKED BY NKM
APPROVED BY MoyizE.
23 9Kg Dry Powder fire extinguisher. 11. All plumbing pipework to be in PP-R PN 16 DATE 18 SEPTEMBER '2016
24 Water / CO2fire extinguisher.

PROJECT NUMBER:
FHR DSU-UNICEF-15-19
25 20ø x 30m long swinging FHR DRAWING NUMBER:
26 PP-R Polypropylene Random Copolymer Pipe DSU-UNICEF-15-19-M002

TENDER DRAWINGS
COPYRIGHT RESERVED
CONSENT.
STRAINER &
FOOT VALVE
UNOPS
63ø PP-R BURIED UNDERGROUND

TO BE CONFIRMED ON SITE
SELF-PRIMING DOMESTIC
WATER BOOSTER PUMP
AS PEDROLLO PRULIJET Nairobi, Kenya.
MODEL 6/200 OR EQUAL &
APPROVED OF CAPACITY
8,000Ltrs AT 60m HEAD
POWER INPUT: 2.2kW, 3Ø
GENERAL NOTES
IV
IV
Note: Pump Room Shall

be sited such that
Pump Room FFL
Shall not be more
63ø PP-R BURIED UNDERGROUND than 2500mm above
free water level
in the lake
PROPOSED
POWER CABLE
ROUTE AND LENGTH
CLIENT
UNICEF
PROJECT
INFRASTRUCTURE
UPGRADE TO
NYANDIWA HEALTH
CENTRE HOMABAY
COUNTY
DRAWING TITLE
SITE PLAN- WATER

RETICULATION

DRAWN BY O.S
CHECKED BY NKM
2No. NEW WATER STORAGE TANKs CAPACITY : 10,000Ltrs EACH
APPROVED BY MoyizE.
DATE 18 SEPTEMBER '2016

50ø PR
PROJECT NUMBER:
50ø CONNECTION TO
50ø OFP
WATER TREATMENT/
RETICULATION SYSTEM
DSU-UNICEF-15-19
DRAWING NUMBER:
50ø PR
50ø OFP DSU-UNICEF-15-19-M003

TENDER DRAWINGS
COPYRIGHT RESERVED
ED PLATFORM TO SE's DETAIL

CONSENT.
UNOPS
2No. NEW WATER STORAGE TANKs
CAPACITY : 10,000Ltrs EACH
AS TOP-TANK OR APPROVED EQUIVALENT
ON EXISTING ELEVATED PLATFORM Operational excellence for results that matter
50ø OVERFLOW
Nairobi, Kenya.
GENERAL NOTES
50øCWS
50øCWS
/TREATMENT SYSTEM50øCWS TO RETICULATION
PRESSURISED MAINS
CLIENT
UNICEF
PROJECT
SELF-PRIMING DOMESTIC INFRASTRUCTURE

Note: Pump Room Shall WATER BOOSTER PUMP UPGRADE TO
be sited such that AS PEDROLLO PRULIJET NYANDIWA HEALTH
Pump Room FFL MODEL 6/200 OR EQUAL & CENTRE HOMABAY
shall not be more APPROVED OF CAPACITY COUNTY
than 2500mm above 8,000Ltrs AT 60m HEAD
DRAWING TITLE
free water level POWER INPUT: 2.2kW, 3Ø

(FWL) in the lake WATER DISTRIBUTION
SCHEMATIC
2500mm
63øCWS DESIGN SERVICES UNIT

max
FWL DRAWN BY O.S
APPROVEDBY
CHECKED BY NKM
DATE MoyizE.
18 SEPTEMBER '2016
PROJECT NUMBER:
63øCWS
DSU-UNICEF-15-19
DRAWING NUMBER:
DSU-UNICEF-15-19-M004
TENDER DRAWINGS
FOOTVALVE COPYRIGHT RESERVED
C/W THIS DESIGN AND DETAIL ARE,
STRAINER PROPERTY OF THE UNOPS/EAH,NAIROBI
CONSENT.
STRUCTURAL DESIGNS AND DRAWINGS
PROJECT.
TO NYANDIWA SUB COUNTY
HOSPITAL -
HOMABAY COUNTY
OCTOBER 2 0 16
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in millimetres,

of any work.

are
the drawing.

proceeding.
CLIENT
UNICEF
PROJECT
HOSPITAL, HOMABAY COUNTY
DRAWING TITLE
WATER TANK TOWER

FOUNDATION DETAILS

DRAWN BY Lang'at Z.
CHECKED BY Philip M.
APPROVED BY Moyiz E.
DATE OCTOBER 2016
PROJECT NUMBER:
DSU-UNICEF-15-29
DRAWING NUMBER:
S-201
TENDER DRAWINGS
COPYRIGHT RESERVED
CONSENT.
UNOPS
Nairobi, Kenya.
GENERAL NOTES

of any work.

are
the drawing.

proceeding.
CLIENT
UNICEF
PROJECT
HOSPITAL, HOMABAY COUNTY
DRAWING TITLE
WATER TANK TOWER

DETAILS

DRAWN BY Lang'at Z.
DATE OCTOBER 2016
PROJECT NUMBER:
DSU-UNICEF-15-29
DRAWING NUMBER:
S-202
TENDER DRAWINGS
COPYRIGHT RESERVED
CONSENT.
UNOPS
Nairobi, Kenya.
GENERAL NOTES

of any work.

are
the drawing.

proceeding.
CLIENT
UNICEF
PROJECT
TO KAIKOR SUB-COUNTY
HOSPITAL
DRAWING TITLE
GROUND WATER
TANK, INCINERATOR
PLINTH & PLACENTA
PIT DETAILS
DRAWN BY Lang'at Z.
DATE OCTOBER 2016
PROJECT NUMBER:
DSU-UNICEF-15-29
DRAWING NUMBER:
S-203
TENDER DRAWINGS
COPYRIGHT RESERVED
CONSENT.
A B
UNOPS
2200
100MM THICK CONCRETE FLOOR SLAB
A B
D.O.S MIN. 1500MM

BRC MESH FABRIC NO. A142
1 2200 Operational excellence for results that matter

B1 B1
1000 GAUGE POLYTHENESHEETING
300X200 RING BEAM 50MM THICK MURRAM/SAND

RAMMED AND WELL COMPACTED BLINDING UNOPS Building, UN lane,
1 1
300mm THICK WELL COMPACTED
HARDCORE (COMPACT IN LAYERS OF
C1 C1 150mm)
C1 C1 Nairobi, Kenya .
1 Y8-04-175CC LINKS
4Y12-03 GENERAL NOTES
300X200 RING BEAM
300X200 RING BEAM

8Y12-02-150CC B2
8Y12-01-150CC B1
300
A142 BRC MESH
2200
50mm THICK LEAN
2200
CONCRETE BLINDING (1:4:8 MIX)
2 2 350
300
1000
350 2. All dimensions to be checked and
SECTION THROUGH COLUMN C1(300x200mm)
500
1200 500 ON BASE B1(1000x1000x300mm) of any work.
SCALE 1:25
350 300 350 3. Written dimensions overrides
2 are
C1
C1
C1
8Y12-02-150
400
B2
C1
the drawing.
8Y12-01-150 B1
300X200 RING BEAM
2
400200
B1
B1
1000
2 4. Any discrepancy to be reported to
RING BEAM PLAN LAYOUT proceeding.
2 SCALE 1:50 NO. REVISION DATE APPR.
1000
B1 PLAN
A 150x50 timber rafter B

@550mm c/c 100MM THICK CONCRETE FLOOR
SLAB
DPC TO ENGINEER'S APPROVAL BRC MESH FABRIC NO.

CLIENT
A142 1000 GAUGE POLYTHENE
UNICEF
BRC MESH FABRIC NO. 200
A142 1000 GAUGE POLYTHENE +0.300 SHEETING
SHEETING 100mm CRUSHER

RUN COMPACTED TO 90% BS
100mm CRUSHER RUN HEAVY
+0.300 COMPACTED TO 90% BS HEAVY
TO BE DECIDED ON SITE BY ENGINEER.
TO BE DECIDED ON SITE BY ENGINEER.

1
300mm THICK WELL COMPACTED HARDCORE
(COMPACT IN LAYERS OF 150mm)
300mm THICK WELL COMPACTED HARDCORE

550
(COMPACT IN LAYERS OF 150mm) PROJECT

BACKFILL TO SUIT SITE CONDITIONS
BACKFILL TO SUIT SITE CONDITIONS

200mm (NOMINAL) LOAD BEARING
MASONRY STONE WALLS
(CEMENT MORTAR 1:3)
200mm (NOMINAL) LOAD BEARING
MASONRY STONE WALLS
HOSPITAL, HOMABAY COUNTY.
550
3Y10-06
(CEMENT MORTAR 1:3)
Y10-05 100x100x3mm L-CLEAT, 100mm LONG BENT
3Y10-06
FROM M.S. PLATE. FIRMLY FIXED WITH
DRAWING TITLE
300
WOOD SCREWS & NAILS TO WALL PLATE &
200
Y10-05
50mm THICK LEAN CONCRETE RAFTERS/TRUSSES.
50mm THICK LEAN CONCRETE BLINDING (1:4:8 MIX)
BLINDING (1:4:8 MIX) 200 200 200 PUMP HOUSE DETAILS

550
600 WALL PLATE FIXED TO RING BEAM

200 200 200 TYP. RING BEAM WITH 1.5mm THICK HOOP IRON OR
SECTION 2 -- 2
600 DETAIL AT DOOR OPENINGS
Ø12mm HOLD DOWN BOLTS @ 600
150 CENTRE TO CENTRE
SECTION 1 - 1 SCALE 1:20
STRIP FOOTING DETAIL
SCALE 1:20
TYPICAL EAVES JOINT DESIGN SERVICES UNIT
550
DETAIL SCALE DRAWN BY Lang'at Z.

1:10
2 2Y12-01 CHECKED BY Philip M.

300
500 1200 500

550
Y8-03-175CC LINKS APPROVED BY MoyizE.

BRC MESH FABRIC NO. A142
DATE OCTOBER 2016
2Y12-02
PROJECT
ROOF PLAN 1000 GAUGE NUMBER:
100
200
200
LAYOUT POLYTHENESHEETING
SCALE 1:50
NOTES 200 DSU-UNICEF-15-29
ROOF PITCH =6° TYPICAL 300X200 50MM THICK MURRAM/SAND
DRAWING NUMBER:
RAMMED AND WELL COMPACTED BLINDING
RAFTERS = 150X50mm @550mm C/C
RING BEAM SECTION
PURLINS = 100X50mm @600mm C/C 300mm THICK WELL COMPACTED HARDCORE S-201
RING BEAM =300x200mm SCALE 1:20 (COMPACT IN LAYERS OF 150mm)
TENDER DRAWINGS
COPYRIGHT RESERVED
TYPICAL SECTION 1---1 LAYOUT REPRODUCED WITHOUT WRITTEN
SCALE 1:25 CONSENT.
ANNEX D (I) ELECTRICAL, MECHANICAL AND
IMPLEMENTING AGENCY.
FUNDING AGENCY.
PROJECT.
APPLICATION OF GREEN INFRASTRUCTURE

HOMABAY COUNTY
JANUARY 2017
ELECTRICAL DESIGNS AND DRAWINGS
PROJECT.

HOMABAY COUNTY
JANUARY 2017
UNOPS
Operational excellence for results that
matter
East Africa Hub (EAH),
Nairobi
LIST OF DRAWINGS Nairobi, Kenya.
NOTES
ITE DRAWING TITLE unless otherwise stated.

M confirmed on site before
commencement
of any work.
1. GTA-SLP-03-K1HC-ES-01 DRAWINGS LIST SCHEDULE
scaled
2. GTA-SLP-03-K1HC-ES-02 LEGEND OF SYMBOLS AND LIST OF LIGHT FITTINGS from
the drawing.

the
3. GTA-SLP-03-K1HC-ES-03 SITE PLAN Engineer promptly before proceeding.
4. GTA-SLP-03-K1HC-ES-04 LIGHTING 1. Revision R0 21.11.16
5. GTA-SLP-03-K1HC-ES-05 POWER
CLIENT
6. GTA-SLP-03-K1HC-ES-06 SOLAR POWER INSTALLATIONS AND CONSUMER UNIT SCHEMATICS

DRAWING
PROJECT
7. GTA-SLP-03-K1HC-ES-07 LIGHT FITTINGS LOCATION TYPICAL LAYOUT GREEN-TECH PROJECT

NYADIWA HEALTH CENTER
8. GTA-SLP-03-K1HC-ES-08 TYPICAL LIGHT FITTINGS MOUNTING DETAIL

DRAWING TITLE
DRAWINGS LIST SCHEDULE
9. GTA-SLP-03-K1HC-ES-09 SOLAR PV MOUNTING DETAIL. PLAN AND TYPICAL SOLAR PV PANEL DETAIL. DESIGN SERVICES UNIT
DRAWN BY Virginia K
CHECKED BY Umang A
10. GTA-SLP-03-K1HC-ES-10 SOLAR PV MOUNTING DETAIL APPROVED BY Baskaran V
DATE NOVEMBER 2016
PROJECT NUMBER:
11. GTA-SLP-03-K1HC-ES-11 BATTERY ROOM SECTION AND PLAN GTA-SLP-03- K1HC

DRAWING NUMBER:
ES-01 SCALE NTS
12. GTA-SLP-03-K1HC-ES-12 BATTERY RACK & INVERTER RACK TENDER DRAWINGS

COPYRIGHT RESERVED
ABBREVIATIONS
UNOPS
ABBREV DESCRIPTION matter
DRAWINGS CL CURRENT LIMITED East Africa Hub (EAH),
NUMBER DESCRIPTION HG HEAVY GAUGE Nairobi
ES/01 SCHEDULE OF LIGHT FITTINGS AND LEGEND OF SYMBOLS
PVC POLYVINYL CHLORIDE UNOPS Building, UN lane,
ES/02 LIGHTING AND POWER LAYOUT
BT BOTTOM ENTRY Off Avenue P.O. Box 783,
TT TOP ENTRY Village Market, 00621
ES/03 SCHEMATIC WIRING DIAGRAM TT / BT TOP AND BOTTOM ENTRY, TOP AND BOTTOM EXIT
Nairobi, Kenya.
ES/04 CIR CIRCUIT
TYPICAL LIGHT FITTINGS LOCATION LAYOUT
ES/05 SITE PLAN TP / N OR TPN TRIPLE POLE AND NEUTRAL
NOTES
SP / N OR SPN SINGLE POLE AND NEUTRAL 1. All dimensions are in millimetres,
CU CONSUMER UNIT
DB DISTRIBUTION BOARD 2. All dimensions to be checked and

LV LOW VOLTAGE
commencement
SWG STANDARD WIRE GAUGE of any work.
SCHEDULE OF LIGHT FITTINGS MM MILLIMETRE
SQ MM scaled
SYMBOL DESCRIPTION SQUARE MILLIMETRE
EMS EMERGENCY STOP to be read and not at any time scaled
NOTE: ALL LAMPS TO BE SOFT WHITE / DAYLIGHT (COLOUR TEMPERATURE), WITH GOOD COLOUR RENDERING from
SWA STEEL WIRE ARMOURED
PENDANT CEILING ROSE FITTING COMPLETE WITH 300MM 3 - CORE, O.75SQMM WHITE FLEXIBLE AND the drawing.
C1
HEAT RESISTANT CORD WITH GRIP LAMP HOLDER COMPLETE WITH 16W LED BULB AFFL AFTER FINISHED FLOOR LEVEL / ABOVE FLOOR FINISHED LEVEL
SPHERICAL SCREW NECK BALL FITTING COMPLETE WITH 12W LED FITTING MCB MINIATURE CIRCUIT BREAKER
C2
the
MCCB MOULDED CASE CIRCUIT BREAKER Engineer promptly before proceeding.
S1 WALL MOUNTED VANDAL PROOF SECURITY LIGHT (TO IP54) COMPLETE WITH 18W LED LAMP/ BULB.
CP CONTROL PANEL
BCC BATTERY CHARGER CONTROLLER
CT CURRENT TRANSFORMER NO REVISION DATE APPR.

.
VT VOLTAGE TRANSFOMER
1. Revision R0 21.11.16
C/W COMPLETE WITH
LIGHTING ACCESSORIES AMF AUTOMATIC MAINS FAILURE
SYMBOL DESCRIPTION ATS AUTOMATIC TRANSFER SWITCH
10A 1GANG 1WAY LIGHT SWITCH ECC EARTH CONDUCTIVE CONDUCTOR
A AMPERE CLIENT
10A 2GANG 1WAY LIGHT SWITCH
KVA KILOVOLT AMPERE
V VOLT
UPS UNINTERRUPTED POWER SUPPLY
10A INTERMEDIATE LIGHT SWITCH
HD HEAT DETECTOR PROJECT
SD SMOKE DETECTOR GREEN-TECH PROJECT
TS TIME SWITCH
PEC PHOTOELECTRIC CELL
AB ADAPTABLE BOX DRAWING TITLE
JB JUNCTION BOX
LEGEND OF SYMBOLS AND
PIR PASSIVE INFRARED SCHEDULE OF LIGHTING FITTINGS
HM HEAT MOTION DETECTOR
POWER LEGEND
BG BREAK GLASS DESIGN SERVICES UNIT
SYMBOL DESCRIPTION
H/L HIGH LEVEL DRAWN BY Virginia K
13A SINGLE SWITCHED SOCKET OUTLET (WITH GREEN COLOURED FACE PLATES)
13A TWIN SWITCHED SOCKET OUTLET (WITH GREEN COLOURED FACE PLATES)
EPS EMERGENCY POWER SUPPLY CHECKED BY Umang A
20A DOUBLE POLE SWITCH UPVC UNPLASTICISED POLYVINYL CHLORIDE APPROVED Baskaran V
BY
JUNCTION BOX WITH 3x16A SOCKETS CCU COOKER CONTROL UNIT
DATE NOVEMBER 2016
CU CONSUMER UNIT NTS NOT TO SCALE PROJECT NUMBER:
ELV EXTRA LOW VOLTAGE
ISOLATOR SWITCH GTA-SLP-03- K1HC
CLB CABLE LOOPING BOX HG HEAVY GAUGE DRAWING NUMBER:
GI GALVANISED IRON ES-02 SCALE NTS

AWTL ABOVE WORKTOP LEVEL TENDER DRAWINGS
600 X 450 X 6000 DEEP POWER MANHOLE COMPLETE HEAVY DUTY COPYRIGHT RESERVED
WATER PROOF CONCRETE COVER THIS DESIGN AND DETAIL ARE, AND
500 X 500 X 500 DEEP COMMUNICATION MANHOLE COMPLETE WITH HEAVY DUTY CAST IRON AT ALL TIMES THE EXCLUSIVE
COVER ON PAVEMENTS AND DRIVE WAYS PROPERTY OF THE UNOPS/EAH,NAIROBI
LAKE VICTORIA
UNOPS
Nairobi, Kenya.
MATERNITY NOTES
BUILDING
commencement
SCHEDULED
of any work.
scaled
FOR
from
STAFF QUARTERS the drawing.
TYPE 1
GREENTECH
the
UPGRADE 2 PIT
LATRINES
NO. REVISION
1. Revision R0
DATE
21.11.16
APPR.
STAFF QUARTERS
KITCHEN/LAUNDRY TYPE 2
CLIENT
PROJECT
GREEN-TECH PROJECT
WARDS
DRAWING TITLE
SITE PLAN
OPD BLOCK DESIGN SERVICES UNIT

DRAWN BY Virginia K
2 PIT CHECKED BY Umang A
SINGLE LINE PLAN APPROVED BY Baskaran V
SITE PLAN DATE
PROJECT NUMBER:
NOVEMBER 2016
MATERNITY BLOCK GTA-SLP-03- K1HC

DRAWING NUMBER:
ES-03 SCALE NTS

TENDER DRAWINGS
COPYRIGHT RESERVED
BATH TIOLET
NO WATER
GUTTER
E
VERANDAH RAMP
up
2 BATH, 3
TOILETS
PNC WAITING AREA

MCH
DELIVARY
OFFICE
STORE
PASSAGE
ANC
UNOPS
E
BATH TIOLET VERANDAH RAMP Village Market, 00621
3000 1000 1000 1600 up 1500 1700
4 600 3000 6300 Nairobi, Kenya.
S1 S1
NOTES
CCT-2 2 BATH, 3 1. All dimensions are in millimetres,
1500
C1 C2 C2 C1 C2 TOILETS unless otherwise stated.
CCT-1 CCT-1
C1 C1 C1 CCT-2 2. All dimensions to be checked and
CCT-1
PNC WAITING AREA C2 confirmed on site before
commencement
1200
CCT-1
C1 CCT-1
CCT-1
MCH
CCT-2 C1 C2 of any work.
CCT-2 3. Written dimensions overrides

CCT-1 scaled
C1 C1 C1 C1 C1
6300
C1 C1 C1 to be read and not at any time scaled
1200
CCT-1 CCT-2 CCT-2 CCT-2 from
the drawing.
DELIVARY CCT-2 C2
CCT-2 C1 4. Any discrepancy to be reported to
the
1200
CCT-2
CCT-1
C2
OFFICE Engineer promptly before proceeding.
C1 C1 C1
STORE C2
PASSAGE C1 C1 C1
C1 C1 CCT-1 CCT-2
1200
ANC C2 1. Revision R0 21.11.16
5000 10400 2100 2000 1000 1500 1700
SINGLE LINE PLAN CLIENT
MATERNITY BLOCK
PROJECT
KEY
GREEN-TECH PROJECT
SYMBOL DESCRIPTION NYADIWA HEALTH CENTER
Lighting wiring
DRAWING TITLE
20mm Diameter conduit for lighting

NOTES FOR EXECUTION LIGHTING
1. Electrical installation shall be carried in DESIGN SERVICES UNIT

LEGEND accordance with the latest edition of the IEE
DRAWN BY Virginia K
SYMBOL DESCRIPTION wiring regulations.
2. Switches mounting height shall be at 1400mm CHECKED BY Umang A
WALL MOUNTED VANDAL PROOF SECURITY LIGHT (TO IP54) COMPLETE WITH 18W from FFL.
S1 LED LAMP/ BULB. 3. Sockets mounting heights shall be at 300mm
APPROVED BY Baskaran V
DATE
PENDANT CEILING ROSE FITTING COMPLETE WITH 300MM 3 - CORE, O.75SQMM from FFL. PROJECT NUMBER:
NOVEMBER 2016
C1 WHITE FLEXIBLE AND HEAT RESISTANT CORD WITH GRIP LAMP HOLDER 4. All wiring to run in straight angles, along wall GTA-SLP-03- K1HC
COMPLETE WITH 16W LED BULB & ceiling inside PVC casing adhering to
DRAWING NUMBER:
electrical installation specifications
C2 SPHERICAL SCREW NECK BALL FITTING COMPLETE WITH 12W LED FITTING 5. The existing electrical wiring and fixture not to be ES-04
TENDER DRAWINGS
SCALE NTS
disturbed/ altered/ replaced in any capacity. The

13A SINGLE SWITCHED SOCKET OUTLET (WITH GREEN COLOURED FACE PLATES) new wiring and fixtures to be installed in COPYRIGHT RESERVED
separation to existing. AT ALL TIMES THE EXCLUSIVE
UNOPS
NO WATER Operational excellence for results that matter
GUTTER East Africa Hub (EAH), Nairobi
BATH TIOLET VERANDAH

E UNOPS Building, UN lane,
RAMP Village Market, 00621
3000 1000 1000 1600 4600 3000 up 6300 1500 1700 Nairobi, Kenya.
NOTES
CCT-4 CCT-4
1500
2 BATH, unless otherwise stated.
3
TOILETS confirmed on site before
PNC WAITING AREA commencement
1200
MCH of any work.

scaled
6300
1200
from
CCT-5 the drawing.
DELIVARY
the
CCT-3
1200
OFFICE Engineer promptly before proceeding.
STORE
PASSAGE
CCT-5
1200
CCT-3 CCT-3 ANC CU-S 1. Revision 21.11.16

JB R0
5000 10400 2100 2000 1000 1500 1700
MATERNITY BLOCK
PROJECT
KEY GREEN-TECH PROJECT

SYMBOL DESCRIPTION
DRAWING TITLE
25MM CONDUIT FOR POWER

POWER

LEGEND DRAWN BY Virginia K
SYMBOL DESCRIPTION
CHECKED BY Umang A
JB
DATE NOVEMBER 2016
JUNCTION BOX PROJECT NUMBER:
GTA-SLP-03- K1HC
DRAWING NUMBER:
13A SINGLE SWITCHED SOCKET OUTLET (WITH GREEN COLOURED FACE PLATES) ES-05 SCALE NTS
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
CABLES: Village Market, 00621
Nairobi, Kenya.
250W, 12V PV SOLAR PANELS CONNECTED
1. 4SQ.MM SC XLPE/SWA/XLPE COPPER
(SERIES OF 4'S) NOTES
CABLE 2. 4SQ.MM 2C XLPE/SWA/XLPE COPPER
CABLE 1. All dimensions are in millimetres,
12 PV-SOLAR PANELS)
3. 10SQ.MM 2C PVC INSULATED COPPER CABLE unless otherwise stated.
4. 16SQ.MM SC PVC INSULATED COPPER CABLE 2. All dimensions to be checked and
commencement
of any work.
scaled
from
1 1 1 the drawing.
the
1
20A DC 8 WAY
COMBINER 2 2 2 3
ISOLATOR CONSUMER NO. REVISION DATE APPR.
BOX UNIT
1. Revision R0 21.11.16
63A SPN
3500W INTEGRAL
1no. 48VDC, 80A INVERTER
DC CHARGE ISOLATOR
EARTHING CONTROLLER
4 4 AC EARTHING
CLIENT
PROJECT
4X12V BATTERY BANKS; 1X4 GREEN-TECH PROJECT

CONFIGURATION NYADIWA HEALTH CENTER
(12 BATTERIES) 25x3mm 25x3mm
EQUIPOTENTIAL BONDING DRAWING TITLE
COPPER TAPE
SOLAR POWER INSTALLATIONS &
CU SCHEMATIC DRAWING

DRAWN BY Virginia K
10A SP CHECKED BY Umang A

3*1.5 sq. mm sc cables in Ø20mm pvc conduit to lighting cct 1 APPROVED BY Baskaran V
10A SP NOTES FOR EXECUTION
3*1.5 sq. mm sc cables in Ø20mm pvc conduit to lighting cct 2 DATE NOVEMBER 2016
10MM SQ. CABLE
PVC/SWA/PVC 2C 63A SPN 1. with
Electrical installation
the latest edition shall
of thebe carried
IEE wiringin regulations.
accordance
Cu.insulated FROM THE
30A SP 3*2.5 sq mm sc cables in Ø25mm pvc conduit to 13 Amps ringmain socket outlets cct 3
PROJECT NUMBER:
INVERTER 2. Switches mounting height shall be at 1400mm from GTA-SLP-03- K1HC

5kA 30A SP FFL.
DRAWING NUMBER:
3*2.5 sq mm sc cables in Ø25mm pvc conduit to 13 Amps ringmain socket outlets cct 4 ES-06 SCALE NTS
3. Sockets mounting heights shall be at 300mm from
30A SP TENDER DRAWINGS
FFL.
MCB 3*2.5 sq mm sc cables in Ø25mm pvc conduit to 13 Amps ringmain socket outlets cct 5 COPYRIGHT RESERVED
4. All wiring to run in straight angles, along wall &
ceiling inside PVC casing adhering to electrical THIS DESIGN AND DETAIL ARE, AND
Spares AT ALL TIMES THE EXCLUSIVE
installation specifications PROPERTY OF THE UNOPS/EAH,NAIROBI
5. The existing electrical wiring and fixture not to be WITHOUT WRITTEN CONSENT.
Spares disturbed/ altered/ replaced in any capacity. The
new wiring and fixtures to be installed in separation
Spares to existing.
8-WAY,63A SPN CONSUMER UNIT
FOR SOLAR POWER (LIGHTING AND
SMALL POWER
UNOPS

E Off Avenue P.O. Box 783,
Village Market,
Nairobi, Kenya. 00621
3000 1000 1000 up RAMP
1600 4600 3000 6300 1500 1700
NOTES
Y

C2 C2
1500
C1 C1 C2 2 BATH, 3
C1 C1 C1 TOILETS 2. All dimensions to be checked and
PNC WAITING AREA C2 commencement

of any work.
MCH
1200
C1 C1 C2
2Y

scaled
C1 C1
6300
C1 C1 C1 C1 C1 C1 from
1200
C2 the drawing.
DELIVARY 4. Any discrepancy to be reported to
C1
the
2Y
ANC Engineer promptly before proceeding.
1200
OFFICE
STORE
C2 C2
C1 C1 C1 C1 C1
C1
PASSAGE
C1 C1 NO. REVISION DATE APPR.
1200
C2 1. Revision 21.11.16
Y
R0
X 2X 2X X
5000 10400 2100 2000 1000 1500 1700
MATERNITY BLOCK
PROJECT
GREEN-TECH PROJECT
DRAWING TITLE
TYPICAL LIGHT FITTINGS

LOCATION DETAIL
1. DESIGN SERVICES UNIT

DRAWN BY Virginia K
2. CHECKED BY
APPROVED BY
Umang A
Baskaran V
3. DATE
PROJECT NUMBER:
NOVEMBER 2016
4. GTA-SLP-03- K1HC
DRAWING NUMBER:
ES-07 SCALE NTS
5. TENDER DRAWINGS
COPYRIGHT
THISRESERVED
DESIGN AND DETAIL ARE, AND

UNOPS
Nairobi, Kenya.
NOTES
18W wall mounted bulkhead (S1) commencement
of any work.
scaled
GCI ROOF
from
10 Amp switch
Typical lamp the drawing.
the
S1
Refer: Specification item 2.4.5 Engineer promptly before proceeding.
1400
2000
13 Amp socket
Refer: Specification item 2.5.2
450 NO. REVISION DATE APPR.
1. Revision R0 21.11.16
SECTION S-02
S1 LED LUMINAIRE MOUNTING DETAIL AND

SWITCH AND 13AMPS MOUNTING HEIGHT Typical CLIENT
lamp
20mm Conduit for lighting C2 PROJECT
GREEN-TECH PROJECT
PVC Pull box above the DRAWING TITLE

ceiling
TYPICAL LIGHT FITTINGS
MOUNTING DETAIL
GCI ROOF

DRAWN BY Virginia K
10 Amp switch CHECKED BY Umang A
Refer: Specification item 2.4.5 Typical lamp APPROVED BY Baskaran V
1400
13 Amp socket DATE NOVEMBER 2016
Refer: Specification item 2.5.2 PROJECT NUMBER:

450
C1 GTA-SLP-03- K1HC
DRAWING NUMBER:
ES-08 SCALE NTS
CI MOUNTING DETAIL
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
250W Solar PV Village Market, 00621
Nairobi, Kenya.
panel NOTES
millimetres, unless otherwise
stated.

commencement
1689
of any work.
1,000 3. Written dimensions overrides

scaled
Ridge Line Ridge Line from
the drawing.

the

.
Revision 21.11.16
1. R0
ROOF TOP PANELS

LAYOUT DETAILS CLIENT
106.65
961
-+
NOTES: PROJECT
GREEN-TECH PROJECT
1. INSTALLATION TO BE COMPLETED IN ACCORDANCE
WITH MANUFACTURER'S SPECIFICATIONS.
39.37"(1000)
(180.85)
DRAWING TITLE
2. THESE DESIGN DRAWINGS ARE NOT FOR SOLAR PV MOUNTING DETAIL PLAN
VIEW & TYPICAL SOLAR PV PANEL
CONSTRUCTION PURPOSES AND ARE FOR DETAIL
GUIDANCE
1689
PURPOSES ONLY.
1114
INFORMATION &
CONTRACTOR TO PRODUCE WORKSHOP DRAWINGS DESIGN SERVICES UNIT
FOR APPROVAL BY THE ENGINEER. DRAWN BY Virginia K
3. PANELS TO BE MOUNTED A MINIMUM OF 300MM FROM CHECKED BY Umang A
THE ROOF EDGES/EAVES. APPROVED BY Baskaran V
4. THE PANEL DIMENSIONS ARE NOT STANDARD AND DATE NOVEMBER 2016
287.5
COULD VARY WITH DIFFERENT MANUFACTURERS. PROJECT NUMBER:
GTA-SLP-03- K1HC
33 1000 5. THERE SHOULD BE A MINIMUM DISTANCE OF 300 MM DRAWING NUMBER:
ISOMETRIC VIEW
FROM EAVES AND RIDGE LINE FOR INSTALLATION OF ES-09
SIDE DETAIL VIEW FRONT DETAIL VIEW SCALE NTS
SOLAR PV PANEL. UNDER NO CIRCUMSTANCE, THE TENDER DRAWINGS
TYPICAL SOLAR PV DETAIL DISTANCE MAY BE REDUCED TO LESS THAN 300 MM COPYRIGHT RESERVED
CLEAR. THIS DESIGN AND DETAIL ARE, AND
2'' Angle Line Frame bolted
UNOPS
on a 3'' Flat bar, elevated East Africa Hub (EAH), Nairobi
4'' from the roof Level Off Avenue P.O. Box 783,
Nairobi, Kenya.
3'' Flat bar fastened with J bolt
on Roof Purlins NOTES
stated.
2566 2600 2. All dimensions to be checked

and confirmed on site before
1800 commencement
900
of any work.
2300
3800
3. Written dimensions
overrides scaled
5800 dimensions,thus all dimensions are
to be read and not at any time
scaled from
SECTION S-01
the drawing.
4. Any discrepancy to be reported

to the
(TYPICAL BATTERY ROOM) Engineer promptly before proceeding.
ROOF TOP PANELS NO. REVISION
1. Revision
DATE
21.11.16
APPR.
LAYOUT DETAILS
R0
3'' Flat bat

fastened 2'' Angle Line Frame bolted/
Welded on a 3'' Flat bar,
with J bolt on Roof elevated 4'' from the roof Level
trusses
4,500 CLIENT
3'' Flat bar fastened

with J bolt on Roof
Purlins
2'' Angle Line PROJECT

2,040
Frame bolted
1689
GREEN-TECH PROJECT
1,000 1,000 1,000 1,000 on a 3'' Flat NYADIWA HEALTH CENTER
bar
100
DRAWING TITLE
Mounting 4'' size J bolt Welded

TYPICALSOLAR PV PANEL
MOUNTING DETAIL
100 100 flat to on flat Bar anchored
100 220 on Z bar/timber Purlin
details DESIGN SERVICES UNIT
FRAME DESIGN Flage

to
DRAWN BY Virginia K
LAYOUT details Detail A CHECKED BY Umang A

NOTES: DATE NOVEMBER 2016
1. INSTALLATION TO BE COMPLETED IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS. PROJECT NUMBER:
2. THESE DESIGN DRAWINGS ARE NOT FOR CONSTRUCTION PURPOSES AND ARE FOR INFORMATION & GUIDANCE PURPOSES ONLY. GTA-SLP-03- K1HC
CONTRACTOR TO PRODUCE WORKSHOP DRAWINGS FOR APPROVAL BY THE ENGINEER. DRAWING NUMBER:
3. PANELS TO BE MOUNTED A MINIMUM OF 300MM FROM THE ROOF EDGES/EAVES. ES-10 SCALE NTS
4. THE PANEL DIMENSIONS ARE NOT STANDARD AND COULD VARY WITH DIFFERENT MANUFACTURERS. TENDER DRAWINGS
5. THERE SHOULD BE A MINIMUM DISTANCE OF 300 MM FROM EAVES AND RIDGE LINE FOR INSTALLATION OF SOLAR PV PANEL. UNDER NO
COPYRIGHT RESERVED
CIRCUMSTANCE, THE DISTANCE MAY BE REDUCED TO LESS THAN 300 MM CLEAR. THIS DESIGN AND DETAIL ARE, AND
UNOPS
NO WATER
GUTTER
E RAMP Nairobi, Kenya.
3000 up 1500 1700
3000 1000 1000 1600 4600 6300
NOTES
1500
2 BATH, 3
TOILETS unless otherwise stated.
PNC WAITING AREA 2. All dimensions to be checked and
1200
MCH confirmed on site before
commencement
of any work.
6300
120012001200
DELIVARY scaled
OFFICE
STORE to be read and not at any time scaled
from
PASSAG
E the drawing.
ANC
CU-S 4. Any discrepancy to be reported to
the
5000 10400 2100 2000 1000 1500 1700

1. Revision R0 21.11.16
3500W inverter Charge controller

approximately 44 kgs CLIENT
467
8 No. 225AH batteries
242 on a rack. Stacked in 3 PROJECT
rows, 4 batteries per GREEN-TECH PROJECT

STORE row 2'' Angle Line Frame bolted NYADIWA HEALTH CENTER
on a 3'' Flat bar, elevated

4'' from the roof Level DRAWING TITLE
BATTERY ROOM SECTION AND

CU-S PLAN

3'' Flat bar Virginia K
1000 fastened with J DRAWN BY
bolt on Roof CHECKED BY Umang A

Purlins APPROVED BY Baskaran V
DATE NOVEMBER 2016
PROJECT NUMBER:
GTA-SLP-03- K1HC
8 WAY consumer unit DRAWING NUMBER:
ES-11 SCALE NTS

3500W inverter TENDER DRAWINGS
approx. 44 kgs COPYRIGHT RESERVED
311 THIS DESIGN AND DETAIL ARE, AND
12 No. 225AH batteries on a rack.

1800 311 PROPERTY OF THE UNOPS/EAH,NAIROBI
900 311
Stacked in 3 rows, 4 batteries per row WITHOUT WRITTEN CONSENT.
150 2300
4 no. batteries 264 Kgs
3800
5800
UNOPS
matter
Nairobi
Nairobi, Kenya.
4 no. batteries 264 Kgs NOTES

commencement
of any work.
Steel angle section 3. Written dimensions overrides
scaled
40x40x10mm dimensions,thus all dimensions are
from
the drawing.
the
4 no. batteries 264 Kgs NO. REVISION DATE APPR.

1. Revision R0 21.11.16
Steel angle section

40x40x10mm CLIENT
Steel angle section PROJECT
40x40mm GREEN-TECH PROJECT

DRAWING TITLE
BATTERY RACK AND INVERTER

RACK DETAILS
TYPICAL BATTERY RACK FABRICATION DETAIL DESIGN SERVICES UNIT

DRAWN BY Virginia K
NOTES: CHECKED BY Umang A
1. THEDESIGN DRAWING IS TO BE FOLLOWED FOR FABRICATION OF APPROVED
BY
Baskaran V
BATTERY RACK. CONTRACTOR SHALL NOT DILUTE THE DATE NOVEMBER 2016
SPECIFICATIONS OR ALTER THE RACK DESIGN UNLESS APPROVED IN

PROJECT NUMBER:
GTA-SLP-03- K1HC
WRITING BY GREEN TECH SPECIALIST. CONTRACTOR TO PRODUCE DRAWING NUMBER:
WORKSHOP DRAWINGS OF RACK FOR APPROVAL. ES-12 SCALE NTS
2. THEBATTERY DIMENSIONS ARE NOT STANDARD BUT TYPICAL AND

TENDER DRAWINGS
COPYRIGHT RESERVED
COULD VARY WITH DIFFERENT MANUFACTURERS. THIS DESIGN AND DETAIL ARE, AND
3. THE RACK SIZE SHOULD ALLOW FOR A MINIMUM DISTANCE OF 25 MM AND CANNOT BE USED OR REPRODUCED
BETWEEN ADJACENT BATTERIES.

4. UNDER NO CIRCUMSTANCE, THE MOUNTING HEIGHT CLEARANCE OF TYPICAL BATTERY RACK TYPICAL DEEP-CYCLE
BOTTOM MOST LEVEL SHOULD BE LESS THAN 150 mm FROM FFL.
DESIGN TO BE FOLLOWED SOLAR BATTERY USED FOR
FOR RACK FABRICATION DIMENSIONS CALCULATION
MECHANICAL DESIGNS AND DRAWINGS
PROJECT.

HOMABAY COUNTY
JANUARY 2017
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1.All dimensions are in metres unless
otherwise stated.

of any work.
3.Written dimensions overrides scaled

dimensions, thus all dimensions are to
be read and not at any time scaled from
DRG. No. DRAWING TITLE the drawing.
4.Any discrepancy to be reported to the

Engineer or green tech specialist
before proceeding.
GT-UNICEF-NYAD-M001-R0 MECHANICAL SERVICES DRAWINGS LIST NO. REVISION DATE APPR.

1. R0 19/11/2016
GT-UNICEF-NYAD-M002-R0 MECHANICAL SERVICES LEGEND & GENERAL NOTES

Tender Issue
GT-UNICEF-NYAD-M003-R0 MECHANICAL WORKS AREAS LAYOUT CLIENT
UNICEF
GT-UNICEF-NYAD-M004-R0 MATERNITY BLOCK PLUMBING LAYOUT
PROJECT
GT-UNICEF-NYAD-M005-R0 MATERNITY BLOCK RAIN WATER HARVESTING ROOF LAYOUT PROPOSED GREEN TECH
UPGRADE TO NYADIWA
HC HOMABAY COUNTY.
GT-UNICEF-NYAD-M006-R0 MATERNITY BLOCK RAIN WATER HARVESTING ELEVATION A-A' DRAWING TITLE
MECHANICAL
SERVICES
GT-UNICEF-NYAD-M007-R0 MATERNITY BLOCK RAIN WATER HARVESTING ELEVATION B-B' DRAWING LIST.

GT-UNICEF-NYAD-M008-R0 STEEL PEDESTAL AND SOAK PIT DETAILS DRAWN BY Joseph K.
CHECKED BY Umang A
APPROVED BY Baskaran V.
DATE 19 NOVEMBER '2016

PROJECT NUMBER:
GT-UNICEF
DRAWING NUMBER:
GT-UNICEF-NYAD-M001-R0
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
NOTES 1. All dimensions are in metres unless
LEGEND otherwise stated.
1 PD Pipe Drop 1. The copyright of this drawing is vested in the Engineers and it must not
of any work.
2 PR Pipe Rise. be used or reproduced without their express authority. 3.Written dimensions overrides scaled
dimensions, thus all dimensions are to be
3 H/L High Level. read and not at any time scaled from the
2. This drawing shall be read in conjuction with the Architects drawing.
4 FV Foot Valve. drawing.Any discrepancies MUST be reported to the Engineers. 4.Any discrepancy to be reported to the
Engineer or green tech specialist before
5 BFV - Ball Float Valve. proceeding.
3. This drawing must be checked against existing site conditions and any
6 IV - Isolation Valve. NO. REVISION DATE APPR.
descripancy reported to the Engineers. 1. R0 19/11/2016
7 NRV - Non-Return Valve.
8 Press Action Demand Tap 4. All dimensions are internal diameters and are in millimetres unless
otherwise indicated.
9 Booster Pump-set Tender Issue
10 RWDP Rain Water Down Pipe 5. This drawing should only be used for the specific services intended. CLIENT
11 VP Vent Pipe.
6. This drawing shows the design intent only. The contractor shall be
UNICEF
12 SVP Soil Vent Pipe. responsible for the full co-ordination of the services indicated on this
PROJECT
13 WVP Waste Vent Pipe. and all other services drawings.
PROPOSED GREEN TECH
14 F/A From Above. UPGRADE TO NYADIWA
7. Final access and setting out of services shall be agreed between the HC HOMABAY COUNTY.
15 T/A To Above. architect and the contractor DRAWING TITLE
16 F/B From Below. MECHANICAL

8. Where public health services pass through fire compartmentation ceiling SERVICES
17 T/B To Below. GENERAL NOTES.
voids, floor voids and structural walls the contractor shall sleeve/seal the
18 RE Rodding Eye. opening with an acoustic and fire sealant approved by the architect. DESIGN SERVICES UNIT
19 FT-Floor Trap. DRAWN BY Joseph K.
9. All drainage pipe work shall be in uPVC,heavy duty CHECKED BY Umang A.

20 IC - Inspection Chamber
21 GT - Gully Trap 10. Drainage pipework slopes at 1:100 DATE 19 NOVEMBER '2016
PROJECT NUMBER:
11. All internal plumbing pipework to be in PP-R GT-UNICEF

DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in metres unless
otherwise stated.

LAKE VICTORIA confirmed on site before commencement of
any work.

read and not at any time scaled from the
NO WATER
GUTTER drawing.
BATH TOILET
S-02
VERANDAH
E RAMP
up 1.500 1.700
3.000 1.000 1.000 1.600 4.600 3.000 6.300
X X X
1.200 1.200 1.200 1.200 1.500

XF 2 BATH, 3
TOILETS
WAITING AREA
PNC
proceeding.
MCH X
XF
XF
XF XF
6.300
X
DELIVERY
ANC
OFFICE
STORE
X
PASSAGE XF XF XF X
XF
1. R0 19/11/2016
5.000 10.400 2.100 2.000 1.000 1.500 1.700
S-02
STAFF QUARTERS
SINGLE LINE PLAN
MATERNITY BLOCK TYPE 1
Tender Issue
2NO PVC OHT (
5,000)
CLIENT
UNICEF
2 PIT
LATRINES
MATERNITY BLOCK
SCHEDULED FOR
GREENTECH UPGRADE STAFF QUARTERS
KITCHEN/LAUNDRY TYPE 2 PROJECT
PROPOSED GREEN TECH

UPGRADE TO NYADIWA HC
WARDS
HOMABAY COUNTY.
2
DRAWING TITLE
BATHROOMS
MECHANICAL WORKS
AREAS.
OPD BLOCK
2 PIT
MATERNITY BLOCK LATRINES DRAWN BY Joseph K.
CHECKED BY Umang A
SINGLE LINE PLAN
SITE PLAN DATE 19 NOVEMBER '2016
PROJECT NUMBER:
GT-UNICEF
DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in metres unless
otherwise stated.

confirmed on site before commencement of
2No. 50LITRES HAND-WASH / any work.
WATER STORAGE CANS AS 'ROTO'
OR APPROVED EQUIVALENT ON 3.Written dimensions overrides scaled
600x600x800MM HIGH PLATFORM dimensions, thus all dimensions are to be
TO SE'S DETAILS read and not at any time scaled from the
NO WATER drawing.
GUTTER
IV IV
E
S-02 proceeding.
BATH TOILET VERANDAH RAMP
4.600 up 1.500 1.700
3.000 1.000 1.000 1.600 3.000 6.300
19/11/2016
1.500
1. R0
X X X
XF 2 BATH, 3
TOILETS
WAITING AREA
1.200
PNC
XF
MCH X Tender Issue
XF XF XF CLIENT
6.300
1.200
X UNICEF
DELIVERY
1.200
ANC X
PROJECT
OFFICE
STORE
PASSAGE
PROPOSED GREEN TECH
XF XF XF XF X
1.200
HOMABAY COUNTY.
DRAWING TITLE
5.000 2.100 2.000 1.000 1.500 1.700 MATERNITY BLOCK

10.400
PLUMBING LAYOUT
S-02
SINGLE LINE PLAN DRAWN BY Joseph K.
MATERNITY BLOCK CHECKED BY
APPROVED BY
Umang A
Baskaran V.

PROJECT NUMBER:
GT-UNICEF
DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
A A' 1. All dimensions are in metres unless

otherwise stated.

any work.

Wall Line Below drawing.

proceeding.
0.300
1. R0 19/11/2016
FALL
3.150
Tender Issue
Ridge Line Ri dg e Line
CLIENT
25Ø 5,000LITRES GROUND LEVEL
UNICEF
FALL
3.150
RAINWATER HARVESTING
CWS TANK AS TOP TANK OR
APPROVED EQUIVALENT ON
IV 600mm HIGH MASONRY
PLATFORM TO SE'S DETAILS
82Ø
uPVC
0.300
RWDP PROJECT
100Ø
uPVC PROPOSED GREEN TECH
OFP
HOMABAY COUNTY.
0.300 23.700 0.300 DRAWING TITLE
MATERNITY BLOCK RAIN
WATER HARVESTING ROOF
LAYOUT

DRAWN BY Joseph K.
Umang A
B'
CHECKED BY
B APPROVED BY Baskaran V.

PROJECT NUMBER:
MATERNITY BLOCK ROOF PLAN GT-UNICEF

DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1. All dimensions are in millimetres unless
otherwise stated.

any work.

drawing.
4900
5,000LITRES GROUND proceeding.
LEVEL RAINWATER
HARVESTING TANK AS TOP D5
TANK OR APPROVED
EQUIVALENT NO. REVISION DATE APPR.
1. R0 19/11/2016
MASONRY PLATFORM TO
SE'S DETAILS
ELEVATION A-A' Ground Level
Tender Issue
CLIENT
UNICEF
D5 - Rain water harvesting tank demand push tap
PROJECT
PROPOSED GREEN TECH

Details Minimum operating pressure - 0.2bar, Flow rate at 3 bar UPGRADE TO NYADIWA HC
NOTES FOR EXECUTION: pressure - 15l/min HOMABAY COUNTY.
DRAWING TITLE
1.Works involve installation of a new rain water Finish Chrome plated/bronze MATERNITY BLOCK RAIN
gutter system WATER HARVESTING
Specification manufacture - Chapter 4 item 4.2.13 (BS 1010), execution
2.Demand push taps to be used for the document reference ELEVATION A-A'
instructions - section 3 item 3.2 & section 4 item 4.6.15
rainwater harvesting tanks outlets roof rain
water drain Bills of Quantities DESIGN SERVICES UNIT
Item 1c
document reference
DRAWN BY Joseph K.
CHECKED BY Umang A

PROJECT NUMBER:
MATERNITY BLOCK ROOF PLAN GT-UNICEF

DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
1.All dimensions are in millimetres unless
otherwise stated.

of any work.

dimensions, thus all dimensions are to
be read and not at any time scaled from
the drawing.

Engineer or green tech specialist
before proceeding.
4900
1. R0
19/11/2016
5,000LITRES GROUND
LEVEL RAINWATER
HARVESTING TANK AS
TOP TANK OR APPROVED
EQUIVALENT
Tender Issue
CLIENT
ELEVATION B-B' Ground Level

MASONRY PLATFORM TO
SE'S DETAILS UNICEF
PROJECT
PROPOSED GREEN TECH

UPGRADE TO NYADIWA
HC HOMABAY COUNTY.
DRAWING TITLE
MATERNITY BLOCK RAIN

MATERNITY BLOCK WATER HARVESTING
ROOF PLAN ELEVATION B-B'

DRAWN BY
Joseph K.
CHECKED BY
Umang A
APPROVED BY
Baskaran V.

PROJECT NUMBER:
GT-UNICEF
DRAWING NUMBER:
TENDER DRAWINGS
COPYRIGHT RESERVED
50Lts Plastic Hand wash
tank unit with tap UNOPS
STEEL L ANGLE 100MM
HIGH Off Avenue P.O. Box 783,
Nairobi, Kenya.
TAP
CHECKERED STEEL
PLATE TO FORM THE
TOP OF THE STAND
GENERAL NOTES
WELDED TO STEEL L
SECTIONS AT BOTTOM 1. All dimensions are in Centimetres unless
otherwise stated.
STEEL L ANGLE SECTIONS
30X30X440MM LONG TO JOIN LEGS OF
STAND, WELDED TO LEGS ON TOP END
11 NOTES: 2. All dimensions to be checked and
any work.
STEEL L ANGLE SECTIONS 40X40X440MM STEEL L ANGLE 1. This drawing shows the design intent only. The
LONG TO JOIN LEGS OF STAND, WELDED
SECTIONS 60X60X 800 3.Written dimensions overrides scaled
TO LEGS ON TOP END LONG
OFTO FORM
STAND LEGS
ON ALL 42 42 contractor shall be responsible for the full
co-ordination of the services indicated on this and all dimensions, thus all dimensions are to be
FOUR CORNERS read and not at any time scaled from the
STEEL L ANGLE SECTIONS 60X60X
800MM LONG TO FORM LEGS OF other services drawings. drawing.
STAND ON ALL FOUR CORNERS
proceeding.
STEEL L ANGLE
SECTIONS 30X30X440MM LONG TO
JOIN LEGS OF STAND, WELDED TO
LEGS ON TOP END
STEEL L ANGLE SECTIONS

40X40X440MM LONG TO JOIN
112 126 1. R0 19/11/2016
LEGS OF STAND,
WELDED TO LEGS ON
TOP END
CONCRETE CONCRETE PEDESTAL

PEDESTAL 150X150X250MM TO HOLD
150X150X250MM TO IRON LEGS OF STAND Tender Issue
HOLD IRON LEGS
OF
64 21 CLIENT
STAND(100 mm SUNK
BELOW THE GROUND 69 70 STEEL L ANGLE
800MM LONG
SECTIONS TO
60X60X 63
62
UNICEF
LEVEL- CONCRETED
FORM LEGS OF STAND
INSITU)
SOAK PIT
900X900X600MM DEEP
WITH STONE BAT
ON ALL FOUR
CORNERS 21
AND STEEL L ANGLE
BALLAST FILL MADE
SECTIONS
TO SOLID
50 mm TH. FINE
21 40X40X440MM LONG
TO JOIN LEGS OF PROJECT
STAND, WELDED TO
AGGREGATE OR
QUARRY DUST LAYER 35 LEGS ON TOP END
CHECKERED STEEL
PROPOSED GREEN TECH
PLATE TO FORM
THE
TOP OF THE STAND 626364 1 26 HOMABAY COUNTY.
HARDCORE FILLING- WELDED TO STEEL L
WELL WATERED SECTIONS AT BOTTOM
AND DRAWING TITLE
COMPACTED
STEEL L ANGLE
SECTIONS
30X30X440MM LONG STEEL PEDESTAL AND
TO JOIN LEGS OF
STAND, WELDED TO SOAK PIT DETAILS.
LEGS ON TOP END
8 DESIGN SERVICES UNIT

84 8 DRAWN BY Joseph K.
STEEL L ANGLE 100MM

HIGH PLASTIC TANK CHECKED BY Umang A
PLACED HERE

PROJECT NUMBER:
GT-UNICEF
DRAWING NUMBER:
TENDER DRAWINGS
SECTIONAL ELEVATION PLAN COPYRIGHT RESERVED
DETAILS OF STEEL PEDESTAL AND SOAK PIT

PROJECT.

HOMABAY COUNTY
JANUARY 2017
SCALE
CLASSIFICAITON DRAWIGN SHEET TITLE SHEET NO.
NO. SCALE :A1 SCALE :A3
G-001 INDEX OF DRAWING LIST AS SHOWN AS SHOWN 01/07

G-002 ENGINEERING NOTES 02/07
WATER TANK BASE S-103 10,000 Litres GROUND TANK SUPPORT DETAILS 05/07
S-104 5000 Litres GROUND TANK SUPPORT DETAILS 06/07
S-105 2500 Litres GROUND TANK SUPPORT DETAILS 07/07
UNOPS
Nairobi
Nairobi, Kenya.
GENERAL NOTES

of any work.
3. Written dimensions overrides scaled

the drawing.

CLIENT
UNICEF
PROJECT
PROPOSED WATER TANK
TOWER AND GROUND
TANK SUPORT
DRAWING TITLE
DRAWING LIST

DRAWN BY Lang'at Z.
DATE May 2016
PROJECT NUMBER:
DSU-UNICEF
DRAWING NUMBER:
G-001
TENDER DRAWINGS
COPYRIGHT RESERVED
GENERAL NOTES FOR STRUCTURAL WORKS
1. General
1.1 All drawings shall be read in conjunction with the relevant G.A., M & E Services, Architectural, equipment supplier's
Standard drawings and specifications. Any discrepancy shall be brought to the notice of Engineer before commencing works.
9. Timber
9.1 All timber to be seasoned cypress Grade II (structural) grade or better in accordance with British
BS 5268 or Euro-code EC5 or approved equivalent)
UNOPS
1.2 All dimensions are in millimetres unless noted otherwise. 9.2 All timber shall be preservative treated as per Technical Specifications.
1.3 All contours and levels are in meters, unless noted otherwise. 9.3 Wall plate to be fixed to concrete beam with 12mm dia. bolts at 600mm c/c. matter
1.4 All grid ordinates are in meters. 9.4 All timber rafters and trusses shall be fixed to wall plate using nails and 3mm thick bend plate.
9.5 Bolts for connection of timber members shall be 16mm dia. black bolts with washers unless noted otherwise.
1.5 All levels indicated are finished floor levels unless noted otherwise.
1.6 EL(+/-)0.00 corresponds to Existing Ground Level. 9.6 Timber shall be well seasoned UNOPS Building, UN lane,
1.7 In the event that any of the notes given in this drawing are in conflict with the requirements of the Technical specification,
9.7 Bolt holes to be 2mm less than bolt diameter.
9.8 Edge distance not less than 4xbolt diameter.
the specification shall take precedence. The conflicting note should in any case be brought to the attention of the Structural
9.9 End distance not less than 2.5x bolt diameter.
Engineer.
Nairobi, Kenya.
1.9 For any specialized construction method (e.g. slip-form) or temporary works (e.g. crane) proposed by the contractor,
10. Finishes
a detailed method statement together with the supporting calculations shall be submitted to the Engineer for approval prior
to implementation of such works. 10.1 Finishes to structural elements shall be in accordance with Architectural drawings
10.2 All structural steelwork delivered to site shall be primed and painted in accordance with the Technical specifications, GENERAL NOTES
and to colour schemes approved by the Architect.
2. Foundation Formation Level 10.3 Finishes for exposed concrete canopy and gutters shall be executed as follows : 1. All dimensions are in millimetres,
2.1 Foundation formation levels for all columns and strip footings to the approval of the Engineer. unless otherwise stated.
- Minimum 12mm thick cement screed laid to falls.
3. Concrete - Water proofing material approved by a specialist shall be laid in accordance with Technical Specifications.
3.1 Concrete mix designs shall be submitted to the Engineer for approval prior to commencement of any concrete works. 10.4 Finishes for roofs supported on Structural steel Members shall be as follows:
3.2 Blinding and mass concrete shall be grade E (1 : 3 : 6) or grade C15 unless noted otherwise.
- Profiled IT4 GI sheets.
3.3 Concrete grade for all reinforced concrete works shall be grade C25 unless noted otherwise. of any work.
3.4 Concrete grade for Water retaining Structures shall not be less than grade C30.
11. Movement Joints 3. Written dimensions overrides scaled
PERMITTED TYPE MAX. SIZE dimensions,thus all dimensions are
PROPOSED USE GRADE OF AGGREGATE AGGREGATE WORKABILITY
COURSE FINE
11.1 Expansion joints shall be of 20mm thick unless noted otherwise. to be read and not at any time scaled
REINFORCED CONC. 11.2 Expansion joints shall consist of flexcell filler or equivalent with mastic sealant to the approval of the Engineer. from
(INCL. GROUND MEDIUM
BEARING SLAB)
C 25 BS 882 BS 882 20 mm
(75) 11.3 Unless shown otherwise ground floor slabs with expansion joints shall have M12x400mm long dowels the drawing.
CONCRETE
MEDIUM
across the joint at 300 C/C with one end debonded & capped to leave 25mm minimum end gap.
CONTAINING NO C 20 BS 882 BS 882 20 mm (75) 11.4 Contraction joints shall have 10mm wide x 20mm deep grooves filled with Mastic Sealant and with
EMBEDDED METAL
MEDIUM M12x400mm long dowels across the joint at 300 C/C, with one end debonded. Engineer promptly before proceeding.
BLINDING CONCRETE C 10 BS 882 BS 882 40 mm
(75) 11.5 Basement and Ground floor slabs shall be cast in panels not exceeding 6m x 6m with contraction joint along the
CONCRETE IN
MEDIUM perimeter for adjacent panels.
MINOR ELEMENTS C 25 BS 882 BS 882 10 mm
(75) NO. REVISION DATE APPR.
EG LINTELS
12. Water Tightness for Concrete
4. Reinforcement
4.1 12.1 Contractor shall ensure water tightness for water retaining or excluding structures by using concrete admixture
All high tensile (T) and mild steel (R) bars to be in accordance with B.S. 4449 and mesh fabric to be made from 'SIKA' or equivalent. Concrete structures required to meet this requirement shall be as specified on the
cold worked steel bars in accordance with B.S. 4483.
drawings.
12.2 All contraction joints for water tight structures shall have 200mm wide PVC water bar unless specifically
4.2 Unless otherwise stated on the drawings minimum clear concrete cover to main reinforcement (i.e excludes links) to be as follows:
Foundations 50mm from blinding surface or 75mm from natural ground indicated otherwise.
Ground floor slab (bottom & sides) 50mm 13. Legend
Ground floor slab (top) 30mm
Retaining walls 40mm 13.1 General legend used on the drawings is as follows
Water tank walls 40mm CLIENT
Columns 40mm FFL Finished floor level
SFL Structural floor level
UNICEF
Beams 30mm (bottom and sides) and 40mm (top)
GL Ground level
Slabs & Staircases 25mm
TOC Top of concrete
Maximum tolerance on concrete cover to be +/- 5mm.
RHS Rectangular hollow section
4.3 Legend for reinforcement specified on the drawings is as follows : SHS Square hollow section
NF Near face CHS Circular hollow section
FF Far face NB Nominal bore PROJECT
EF Each face
EW Each Way
NTS Not to scale PROPOSED WATER
UB Universal beam
B1 Bottom 1st layer UC Universal column
TANK TOWER AND
B2 Bottom 2nd layer RSC Rolled steel channel. GROUND TANK SUPORT
T1 Top 1st layer RSJ Rolled steel joist.
T2 Top 2nd layer RSA Rolled steel angle.
AP Alternately Placed MS Mild steel
AR Alternately Reversed GMS Galvanised mild steel. DRAWING TITLE
STG Staggered
4.4 Minimum laps to all bars to be 50 x Diameter of smaller bar unless otherwise stated. 14. Project Design Loading
4.5 When reinforcing Steel is noted as continuous in beams, Slabs and/or Walls, or when only a typical section The building is classified as "Normal Occupancy" according to BS 6399 and Design carried out for Life Safety based STRUCTURAL NOTES
is given, laps should only be used when they are unavoidable due to stock lengths. In this case all laps on the following Loading Criteria;
shall be Staggered a minimum of 1200mm. The top bar splices should be located 'WITHIN THE MIDDLE HALF OF THE SPAN', 14.1 Dead Loads
and the bottom bar splices should be located at 'SUPPORTS or BETWEEN SUPPORTS & 1/3 SPAN POINT' unless noted Unit weight of concrete: 24.0 KN/m3
otherwise on the drawings. Floor finishes : 01.2 KN/m2
5. False ceiling: 0.25 KN/m2
Structural Steel
5.1 All structural steel work to be grade 43A or 43C unless noted otherwise.
Services (basic Electrical & Mechanical): 0.10 KN/m2
DRAWN BY Lang'at Z.
Partition loads: 1.5 KN/m2
5.2 All bolted connections to use grade 8.8 bolts with washers unless noted otherwise.
200mm thick masonry wall: 4.80 KN/m2
5.3 Connection details for all structural steelwork to be in accordance with Engineer's drawings. CHECKED BY Philip M.
or contractors fabrications drawings approved by the Engineer. 14.2 Imposed / Live Loads
5.4 Contractor shall submit shop drawings for the approval of the Engineer prior to commencement of fabrication. General Office floors: 2.50 KN/m2
5.5 Protection of the structural steelwork to be as per the Technical Specifications. 15. Foundations Bearing Capacity APPROVED BY Moyiz E.
5.6 All open ends of R.H.S. and S.H.S. sections shall be blocked with 3mm thick plates unless noted otherwise. The foundation bearing is assumed to be 75KN/m2 on medium dense sandy soil at approximate depths of 1.2m of excavation.
DATE May 2016
6. Therefore, it is recommended that the contractor carry out site geotechnical investigations and testing prior to
Cement Grout construction in order to confirm the foundation designs PROJECT NUMBER:
6.1 All grouting for bolt pockets and under structural steel base plates shall be done with non-shrink cement grout in
accordance with Technical Specifications 16. Blockwork DSU-UNICEF
All load bearing blockwork to be constructed from solid blocks of
6.2 Grouting
4.0N/mm2 for foundations supporting plant and machinery supplied by plant contractors shall be as DRAWING NUMBER:
min characteristic compressive strength complying with BS 5628 PART 1:
per the requirements of the plant contractors.
Structural use of reinforced masonry G-002
7. Holding Down Bolts Mortar to conform to Mortar designation (III) of Table 1, BS5628 Part 1.
17. STEEL FABRICATION NOTES: TENDER DRAWINGS
7.1 All holding down bolts shall be of grade 8.8 unless noted otherwise. 1. All materials shall be tested for through thickness properties to the specified quality class. BS 5950-2001, 2.1.2
7.2 Holding down bolts shall be set in position as indicated on the drawings by means of templates and shall 2. Manufacturer's certificate of test and inspection shall be issued conforming to BS EN 10204 stating the COPYRIGHT RESERVED
process be securely fixed in position to prevent displacement during concreting. of manufacture and product grade. THIS DESIGN AND DETAIL ARE, AND
8. 3. Preloaded fasteners shall generally be HSFG bolts with associated nuts and washers. AT ALL TIMES THE EXCLUSIVE
Built-in items for plant contractors 4. Steel castings and forgings shall conform to BS 3100. PROPERTY OF THE UNOPS/EAH,NAIROBI
8.1 All built-in items for erection of steelwork and plant by other contractors to be set to the 5. Bedding material for steel bases on concrete foundation shall be done to Engineers AND CANNOT BE USED OR REPRODUCED
approval required tolerances as specified by the plant contractors, and shall be approved by the plant contractor or 6. Structural steel members shall positively be identified by a marking scheme. WITHOUT WRITTEN CONSENT.
Engineer as directed by the Engineer. 7. Cutting shall be by sawing, shearing, cropping or thermal cutting (if permitted). Hand held cutting shall be
used only where it is impractical to use machine cutting.
8. Cut edges shall be true to profile and free from major notches and cutting sarrations.
9. Round hole for pins shall be drilliled,plasmer or laser cut.
10. All weld, bolting and cuttings shall be approved on site before fabrication(prepare sample for erection)
11. All measurement shall be done accurately at all stages.
12. Support to be provided for roof frame units untill they are adequately fixed in the position as shown.
UNOPS
Nairobi, Kenya.
GENERAL NOTES
stated.


A142 BRC MESH scaled dimensions,thus all dimensions
are
2400mm dia. 10,000 liter 2400mm dia. 10,000 litre to be read and not at any time scaled from
plastic Water tank plastic Water tank the drawing.
placed on placed on 600mm high
600mm high masonry platform 4. Any discrepancy to be reported to
masonry platform the Engineer promptly before
proceeding.
450mm Compacted NO. REVISION DATE APPR.
hardcore Fill
200mm thick curved walling 400 300 50mm thick

200 sand fill (blinding layer)
1 1 200 200 100
100mm thick slab
400200600
CLIENT
200mm thick
200mm thick curved walling
support walling
UNICEF
2400 200mm thick
support walling
485
PROJECT
5Y10-06-190 CC B2
200
PROPOSED WATER
TANK TOWER AND
200 600 Y10-05-200mm CC B1 600 200 50mm thick GROUND TANK
800 Blinding layer SUPORT
800
(1:4:8) DRAWING TITLE
SECTION 1--1 THROUGH 10,000 Litres GROUND TANK

GROUND WATER TANK SUPPORT PLAN GROUND WATER TANK SUPPORT PLAN SUPPORT DETAILS
10000 litres (2.4m diameter tank) (100mm Thick Slab) DESIGN SERVICES UNIT
(100mm Thick Slab) SCALE 1:50 DRAWN BY Lang'at Z.

SCALE 1:50 CHECKED BY Philip M.
DATE May 2016
PROJECT NUMBER:
DSU-UNICEF
DRAWING NUMBER:
S-103
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
A142 BRC MESH millimetres, unless otherwise
stated.
2100mm dia. 5,000 liter 2100mm dia. 5,000 litre
plastic Water tank plastic Water tank
placed on 600mm high
placed on 600mm high masonry platform
masonry platform commencement of any work.
450mm Compacted 3. Written dimensions overrides

hardcore Fill scaled dimensions,thus all dimensions
200mm thick curved walling are
400 300 50mm thick
the drawing.
200 sand fill (blinding layer)
proceeding.
1 200 200
100mm thick slab NO. REVISION DATE APPR.
400200600
200mm thick
200mm thick curved walling
support walling
2100 200mm thick

support walling
485
5Y10-06-190 CC B2
200
50mm thick CLIENT
Blinding layer
200 600
800
Y10-05-200mm CC B1 600 200 (1:4:8) UNICEF
800
PROJECT
GROUND WATER TANK SUPPORT PLAN SECTION 1--1 THROUGH PROPOSED WATER
5000 litres (2.1m diameter tank) GROUND WATER TANK SUPPORT PLAN TANK TOWER AND
GROUND TANK
(100mm Thick Slab) (100mm Thick Slab) SUPORT
SCALE 1:50 SCALE 1:50
DRAWING TITLE
5000 Litres GROUND TANK

SUPPORT DETAILS
DRAWN BY Lang'at Z.
DATE May 2016
PROJECT NUMBER:
DSU-UNICEF
DRAWING NUMBER:
S-104
TENDER DRAWINGS
COPYRIGHT RESERVED
UNOPS
Nairobi, Kenya.
GENERAL NOTES
stated.
A142 BRC MESH
1690mm dia. 2500 liter 1690mm dia. 2,500 litre confirmed on site before
plastic Water tank plastic Water tank
placed on 600mm high
placed on 600mm high masonry platform
masonry platform 3. Written dimensions overrides
450mm Compacted are
hardcore Fill to be read and not at any time scaled from
200mm thick curved walling the drawing.
400 300 50mm thick
proceeding.
1 1 sand fill (blinding layer)

200 NO. REVISION DATE APPR.
200 200
100mm thick slab
600
200mm thick 200mm thick
400
support walling curved walling
200
1700 200mm thick CLIENT
support walling
485
5Y10-06-190 CC B2
UNICEF
200
50mm thick
600 Blinding layer
200 Y10-05-200mm CC B1 600 200
800 (1:4:8)
800 PROJECT
PROPOSED WATER
TANK TOWER AND
SECTION 1--1 THROUGH GROUND TANK
GROUND WATER TANK SUPPORT PLAN GROUND WATER TANK SUPPORT PLAN SUPORT
DRAWING TITLE
2500 litres (1.7m diameter tank) (100mm Thick Slab)

(100mm Thick Slab) SCALE 1:50 2500 Litres GROUND TANK
SUPPORT DETAILS
SCALE 1:50
DRAWN BY Lang'at Z.
DATE May 2016
PROJECT NUMBER:
DSU-UNICEF
DRAWING NUMBER:
S-105
TENDER DRAWINGS
COPYRIGHT RESERVED

ITB-KEOH-2017-003 - Section V - Annex D (VII) - NYANDIWA HC DRAWINGS

Uploaded by

Copyright:

Available Formats

ITB-KEOH-2017-003 - Section V - Annex D (VII) - NYANDIWA HC DRAWINGS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ITB-KEOH-2017-003 - Section V - Annex D (VII) - NYANDIWA HC DRAWINGS

Uploaded by

Copyright:

Available Formats

ANNEX D-(i)

ARCHITECTURAL DESIGNS AND DRAWINGS

Operational excellence for results that matter

Infrastructure Upgrade to Nyandiwa

East Africa Hub (EAH), Nairobi

2. All dimensions to be checked and

3. Written dimensions overrides

4. Any discrepancy to be reported to

GOOGLE LOCATION MAP

DESIGN SERVICES UNIT

EXISTING BUILDINGS DSU-UNICEF-15-19

PROPOSED LOCATION OF NEW BUILDINGS AR-000-1

East Africa Hub (EAH), Nairobi

2. All dimensions to be checked and

3. Written dimensions overrides scaled

NO REVISION DATE APPR.

DESIGN SERVICES UNIT

LEGEND CHECKED BY PhilipM.

PROPOSED LOCATION OF NEW BUILDINGS PROJECT NUMBER:

90cm high MS 90cm high

4mm thick chequer

MS plate bolted APPROVED BY MoyizE.

1:5 WATER ELEVATION PLAN scale 1:50 PROPERTY OF THE UNOPS/EAH,NAIROBI

BOTTOM BOTTOM BOTTOM

high solid concrete

1000g polythene d.p.m on 50mm .

scale 1:10 CHECKED BY PhilipM.

r.c lintel Operational excellence for results that matter

East Africa Hub (EAH), Nairobi

N 4. Any discrepancy to be reported to the

NO. REVISION DATE APPR.

12mm dia. slide bolt 300mm CLIENT

receive heavy duty padlock

r.c lintel PROJECT

GROUND DRAWING TITLE

SD 01 elevation scale 1:25 DESIGN SERVICES UNIT

10x10mm solid walling PROJECT NUMBER:

welded bars OUTSIDE DSU-UNICEF-15-19

Clay vent block Section AR-105-b

N-N scale 1:10 TENDER DRAWINGS

DETAIL C scale 1:5

4. Any discrepancy to be reported to the

NO REVISION DATE APPR.

Inspection Chamber UNICEF

metal cover on angle section DRAWING TITLE

frame to site Eng's approval ELECTRICAL INSPECTION

DESIGN SERVICES UNIT

for Inspection chamber AR-106

10cm thick PROPERTY OF THE UNOPS/EAH,NAIROBI

East Africa Hub (EAH), Nairobi

DRG. No. DRAWING TITLE Nairobi, Kenya.

DSU-UNICEF-15-19-M001 MECHANICAL SERVICES DRAWINGS LIST

DSU-UNICEF-15-19-M002 MECHANICAL SERVICES LEGEND & GENERAL NOTES

DSU-UNICEF-15-19-M003 SITE PLAN WATER RETICULATION

DSU-UNICEF-15-19-M004 WATER DISTRIBUTION SCHEMATIC NO. REVISION DATE APPR.

DESIGN SERVICES UNIT

DATE 18 SEPTEMBER '2016

3 H/L High Level. GENERAL NOTES

10 RWDP Rain Water Down Pipe