technology workshop craft home food play outside costumes

How To Build An Alpha Particle Spark Detector

Table of Contents

How To Build An Alpha Particle Spark Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Intro: How To Build An Alpha Particle Spark Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 1: Mark and cut prototyping board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2: Soldering .003 ground wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 3: High Voltage Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Step 4: Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Step 5: Try Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 6: Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/
Intro: How To Build An Alpha Particle Spark Detector
Caution: This device uses a high voltage power supply and radioactive materials. Please follow the proper precautions.

Introduction:

I was introduced to alpha particle spark detectors when I watched a Youtube Video [1] by Carl Willis of his home made spark detector. I like the detector so much I
wanted to build one for myself. So I researched the topic and read the seminal work from 1944 by W.Y. Chang and S. Rosenblum [2]. Overview: The device is pretty
simple. Take a thin tungsten wire, charge it to about 3000 volts with respect to ground. Position the wire approximately 1/16" (1.5 mm) above a smooth brass ground
plate. The air acts like an insulator between the highly charged wire and ground plate. When an alpha particle passes in between the wire and the electrode it ionizes the
air between. The high voltage potential between the wires and the electrode, is triggered by the ionization of the alpha particle, which causes an electrical avalanche that
we see as an electrical discharge (spark) between the wires and the electrode. This detector is only sensitive to alpha (?) particles and will Not detect beta(?), x-ray or
gamma(?) radiation. Our device operates on this same principle but there are a few changes. First I am using thinner copper wires (.003 diameter) that are held at
ground potential. It is the metal plate that is charged to approximately 8000 volts. The wire is positioned approximately 0.1" (3mm) away from the metal plate.

Step 1: Mark and cut prototyping board

We mark the top side of the bard with a rectangle.

Cut out the rectangle.

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/
Step 2: Soldering .003 ground wires.
After the board has the rectangle cut into it. You can solder the .003 copper wire across the opening.

I soldered five wires across the opening, approximately equally spaced.. One one side I soldered a 22 gauge insulated wire that would connect the assembly to ground.

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/
Step 3: High Voltage Plate
Next I obtained a 1/8" thick x 1" x 3/5" metal plate. To this I attached copper foil tape to make an electrical connection. Just about any metal can be used for this plate.
You can also use copper clad PC board. The main criteria for the plate is that it is perfectly flat and doesn't flex or bend.

Step 4: Construction
You can purchase an off-the-shelf adjustable high voltage power supply suitable for this project, see parts list. Using the power supply we wire up our components as
detailed in the schematic, photo of set-up is shown below.

For my test I left all the components exposed, and its easy to show the wiring. However this is not a good idea. Since these are live high voltage components I
recommend putting all the components in a plastic enclosure.

The high voltage metal plate has two 1/8" plastic squares next to it. The prototyping board rests on the plastic squares as shown. The wires are positioned approximately
0.1" above the metal plate.

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/
Step 5: Try Out
Power is applied to the detector. There should not be any electrical discharge until an alpha particle shown is brought near the detector. If your detector immediately
begins to arc, (have a discharge between the wires and plate) use the potentiometer on the adjustable power supply to reduce power. If that doesn't work, you need to
increase the space between the wires and the plate. Also note, the .003 copper wires should be soldered taunt across the opening so that they do not droop down close
to the plate.

If on the other hand you do not get any sparks flying between the wires and the plate, the first thing to check is your alpha particle source. Make sure it is a reasonable
strong alpha source. If you have a Geiger counter capable of detecting alpha radiation use that to check your source.

If the alpha source checks out okay, then you may need to reduce the spacing between the wires and the plate. However, this is usually not the case.

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/
 Step 6: Components
Alpha Particle Spark Detector Components

5-8Kv Adjustable Negative High Voltage Power Supply

.003 Copper or Tungsten Wire (36")

HV Diode 6KV

(4) CAP-560pf-2.5KV

5 Watt 510 ohm resistor

Components may be purchased from Images SI Inc.

Misc. Strong Alpha Particle Source, Proto-typing PC boards, copper foil tape, metal base plate, 12VDC power supply

Related Instructables

How to X-Ray by
Build a Pocket How to see Building a
Ionizing RadSense - A How to observe alpha particles Copenhagen grenadier
Radiation Rad SolidState alpha particles
by Higgs Boson Interpreter by
Detector (PIRD) Gamma by sgubanov
legionlabs
Radiation
by
TheHomebrewGuru Detector by
MoonLanding

Advertisements

Comments
2 comments Add Comment

FrankenPC. says: Nov 3, 2015. 4:42 PM REPLY

JesusG33k says: Nov 3, 2015. 3:21 PM REPLY

http://www.instructables.com/id/How-To-Build-An-Alpha-Particle-Spark-Detector/