Scribd Logo
Upload

Welcome to Scribd!

  • 175 views

    Slab Design Slab C8

    Uploaded by

    Mark Christian Esguerra
    This document provides the design of a one-way reinforced concrete slab for a proposed two-story residential building. It includes details of the slab geometry and loads, material properties, required and provided thicknesses, moment coefficients, factored loads and bending moments, reinforcement calculations and spacing requirements. Reinforcing bars with a diameter of 10mm are specified at varying spacings along the short and long spans to resist the calculated negative and positive bending moments.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Slab Design Slab C8

    Uploaded by

    Mark Christian Esguerra
    175 views1 page
    This document provides the design of a one-way reinforced concrete slab for a proposed two-story residential building. It includes details of the slab geometry and loads, material properties, required and provided thicknesses, moment coefficients, factored loads and bending moments, reinforcement calculations and spacing requirements. Reinforcing bars with a diameter of 10mm are specified at varying spacings along the short and long spans to resist the calculated negative and positive bending moments.

    Original Title

    SLAB DESIGN SLAB C8

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides the design of a one-way reinforced concrete slab for a proposed two-story residential building. It includes details of the slab geometry and loads, material properties, required and provided thicknesses, moment coefficients, factored loads and bending moments, reinforcement calculations and spacing requirements. Reinforcing bars with a diameter of 10mm are specified at varying spacings along the short and long spans to resist the calculated negative and positive bending moments.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    175 views1 page

    Slab Design Slab C8

    Uploaded by

    Mark Christian Esguerra
    This document provides the design of a one-way reinforced concrete slab for a proposed two-story residential building. It includes details of the slab geometry and loads, material properties, required and provided thicknesses, moment coefficients, factored loads and bending moments, reinforcement calculations and spacing requirements. Reinforcing bars with a diameter of 10mm are specified at varying spacings along the short and long spans to resist the calculated negative and positive bending moments.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    DESIGN OF ONE-WAY REINFORCED CONCRETE SLAB

    PROJECT : PROPOSED TWO (2) STOREY RESIDENTIAL


    LOCATION : MARIA AURORA AURORA
    DATE : March 17, 2020
    TITLE : DESIGN OF SLAB FLOOR LEVEL S-2

    CASE : 8 Support Condition.


    La = 3,500 mm. Clear Span Length in the Short Direction.
    Lb = 3,500 mm. Clear Span Length in the Long Direction.
    m= 1.00 Aspect Ratio.
    FLOOR LOADS
    DL1 = 5,000 Pa. Dead Load Excluding Weight of Slab. S5
    DL2 = 2,400 Pa. Weight of Slab.
    LL = 1,900 Pa. Floor Live Load.
    STRUCTURAL MATERIALS
    fc' = 20.7 Mpa. Compressive Strength of Concrete. Lb S1 S6 S2
    fy = 275.8 Mpa. Yield Strength of Reinforcing Bars.
    f= 10 mm. Diameter of Reinforcing Bars. S3
    r MIN = 0.0051 Minimum Steel Ratio Required
    tPROV'D = 100 mm. Thickness of Slab Provided.
    tREQ'D = 90 mm. Thickness of Slab Required by the Code.
    S4
    conc. cover = 20 mm. Clear Concrete Cover.
    de = 75 mm. Effective Depth of Reinforcements.
    MOMENT COEFFICIENTS
    SHORT SPAN
    Ca,NEG = 0.0330 Neg. Moment Coeff. in the Short Direction.
    Ca,DL POS= 0.0200 D.L. Pos. Moment Coeff. in the Short Direction. La
    Ca,LL POS = 0.0280 L.L. Pos. Moment Coeff. in the Short Direction.
    LONG SPAN
    Cb,NEG = 0.0610 Neg. Moment Coeff. in the Long Direction.
    Cb,DL POS= 0.0230 D.L. Pos. Moment Coeff. in the Long Direction.
    Cb,LL POS = 0.0300 L.L. Pos. Moment Coeff. in the Long Direction.
    FACTORED FLOOR LOADS
    WU DL = 8.88 KN/m. Factored Dead Load per Unit Meter Width.
    WU LL = 3.04 KN/m. Factored Live Load per Unit Meter Width.
    WU = 11.92 KN/m. Total Factored Load per Unit Meter Width.
    ULTIMATE BENDING MOMENTS
    SHORT SPAN REINFORCEMENT CALCULATIONS
    -MUa = -Ca,NEG WU La2 a = As fy / 0.85 fc' 1000 As = Mu / 0.9 fy ( d - a / 2 )
    = -4.82 KN-m. = 4.17 mm. = 266 mm². 0.0035
    +MUa = Ca,DL POS WUDL La2 + Ca,LL POS WULL La2 a = As fy / 0.85 fc' 1000 As = Mu / 0.9 fy ( d - a/2 )
    = 3.22 KN-m. = 2.76 mm. = 176 mm2 0.0023
    LONG SPAN
    -MUb = -Cb,NEG WU Lb2 a = As fy / 0.85 fc' 1000 As = Mu / 0.9 fy ( d - a / 2 )
    = -8.91 KN-m. = 7.91 mm. = 505 mm². 0.0067
    +MUb = Cb,DL POS WUDL Lb2 + Cb,LL POS WULL Lb2 a = As fy / 0.85 fc' 1000 As = Mu / 0.9 fy ( d - a/2 )
    = 3.62 KN-m. = 3.11 mm. = 199 mm2 0.0026
    REINFORCEMENT SPACING Max. Spacing of Reinforcements = 300 mm.
    SHORT SPAN Min. Spacing of Reinforcements = 25 mm. SHORT SPAN
    -ncontinuous edge = 4.52 - 10mm. Per Meter Strip. (minimum req't) S1 = 222 mm. O.C. cont.edge
    TOP BARS
    -ndiscontinuous edge = 1.72 - 10mm. Per Meter Strip. (minimum req't) S2 = 300 mm. O.C. cont.edge
    +n midspan = 2.99 - 10mm. Per Meter Strip. (minimum req't) BOT. BARS S3 = 300 mm. O.C. midspan
    LONG SPAN LONG SPAN
    -ncontinuous edge = 6.43 - 10mm. Per Meter Strip. (flexure req't) S4 = 156 mm. O.C. cont.edge
    TOP BARS
    -ndiscontinuous edge = (no disc. Edge)
    +n midspan = 3.37 - 10mm. Per Meter Strip. (minimum req't) BOT. BARS S6 = 297 mm. O.C. midspan

    REINFORCEMENT SCHEDULE
    SHORT SPAN LONG SPAN
    REMARKS
    TOP BAR TOP BAR
    BOT. BAR BOT. BAR
    CONTINUOUS EDGE DISCONTINUOUS EDGE CONTINUOUS EDGE DISCONTINUOUS EDGE

    10 mm. @ 300 10 mm. @ 200 10 mm. @ 300 10 mm. @ 275 10 mm. @ 150 -

    You might also like