Self Diagnosis

Supported model

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

RB1TK Chassis
Segment: BA

MODEL COMMANDER DESTINATION

KDL-32R434A RM-YD093 BRAZIL

KDL-32R434A

Version Date Subject

1.0 09/19/2013 Original Manual Release Date.

LCD Digital Color TV

9-883-540-01
TABLE OF CONTENTS

Cautions and Warnings ...................................................................................ii Section 4 - Exploded View/Part Number Information .................................15

Section 1 - Specifications and Layouts .........................................................1 KDL-32R434A .............................................................................................15

Specifications ................................................................................................1 Connectors ..................................................................................................17

Board Layout .................................................................................................2 Screws .........................................................................................................18

Section 5 - Accessories/Part Number Information .....................................19
Wire Dressing ................................................................................................3
Section 2 - Troubleshooting ...........................................................................4 Accessories and Packaging ........................................................................19

Diagnosing the Error .....................................................................................4 Optional Accessories ...................................................................................19

Viewing the Self Check Diagnosis History .............................................................4

Remote Commander ...................................................................................19

Triage Chart ...................................................................................................5 Appendix A: Encryption Key Components ............................................... A-1

Flowcharts and Diagrams ..............................................................................6
Overall Block Diagram ...........................................................................................6
Standby LED Blinking Flowchart ...........................................................................7
No Video Flowchart ...............................................................................................8
Video Distortion Flowchart .....................................................................................9

Section 3 - Repair Information ......................................................................10

Repairing the TV ..........................................................................................10
Removing the Table-Top Stand ............................................................................10
Removing the Lower Cover .................................................................................10

Replacing the Main Board ........................................................................... 11

Removing the Speakers ..............................................................................14
Removing the Bezel and H Board ...............................................................14

KDL-32R434A i
CAUTIONS AND WARNINGS

CAUTION!! SAFETY CHECK-OUT

These servicing instructions are for use by qualified service personnel only. After correcting the original service problem, perform the following safety
To reduce the risk of electric shock, do not perform any servicing other than checks before releasing the set to the customer:
that contained in the operating instructions unless you are qualified to do so.
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes
and bridges.
WARNING!!
2. Check the interboard wiring to ensure that no wires are “pinched” or
An isolation transformer should be used during any service to avoid possible touching high-wattage resistors.
shock hazard, in case of live chassis.
3. Check that all control knobs, shields, covers, ground straps and
mounting hardware have been replaced. Be absolutely certain that
! SAFETY-RELATED COMPONENT WARNING!! you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors,

There are critical components used in LCD color TVs that are important for that were installed during a previous repair. Point them out to the
safety. These components are identified with shading and ! mark on the customer and recommend their replacement.
schematic diagrams and the parts list. It is essential that these critical parts
be replaced only with the part number specified in the parts list to prevent 5. Look for parts which, though functioning, show obvious signs of
electric shock, fire or other hazard. deterioration. Point them out to the customer and recommend their
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
NOTE: Do not modify the original design without obtaining written permission
replacement of any such line cord to the customer.
from the manufacturer or you will void the original parts and labor warranty.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws
ATTENTION!! and all other exposed metal parts for AC leakage. Check leakage
as described in “Leakage Test”.
For safety reasons, component level repair of the Power Supply Boards
and/or the Inverter Boards is prohibited.

KDL-32R434A ii
 CAUTIONS AND WARNINGS

LEAKAGE TEST HOW TO FIND A GOOD EARTH GROUND

The AC leakage from any exposed metal part to earth ground and from all The cover-plate retaining screw on most AC outlet boxes is at earth ground.
exposed metal parts to any exposed metal part having a return to chassis, Verify the AC outlet box retaining screw ground by connecting a 60W to
must not exceed 0.5 mA (500 microamperes). Leakage current can be 100W incandescent (not a neon or fluorescent lamp) between the hot side
measured by any one of three methods. of the receptacle and the retaining screw. Try both slots, if necessary, to
locate the hot side on the line; the lamp should light at normal brilliance if
1. A commercial leakage tester.
the screw is at ground potential. (see Figure B)
Follow the manufacturers’ instructions provided with the tester.

2. A battery-operated AC milliammeter. Trouble Light

3. Measuring the voltage drop across a resistor by means of a VOM AC Outlet Box
or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so
analog meters must have an accurate low voltage scale. Nearly all
battery-operated digital multimeters that have a 2 VAC range are
suitable. (see Figure A)

To Exposed Metal
Parts on Set Figure B. Checking for earth ground.

AC
0.15 µF Voltmeter
(0.75V)

Earth Ground

Figure A. Use an AC voltmeter to check AC leakage.

KDL-32R434A iii
SECTION 1 - SPECIFICATIONS AND LAYOUTS

SPECIFICATIONS

Siste ma Nome do modelo KDL-32R434A

Sistema de televisão A nalógico: NTSC/PAL-M/PAL-N Energia e outros

Digital: SBTVD-T Requisito de energia 110-220 V CA, 60 Hz
Cobertura de canal V HF: 2-13 Consumo de energia
UHF: 14-69 61 W
em uso
CATV: 1-135
em modo de espera Menos do que 1 W
Sistema do painel Painel LCD (Tela de Cristal Líquido)/Backlight de LED
Tamanho da tela (cm) Aprox. 80,0
Potência de saída dos 5W+5W (polegadas medidas diagonalmente) 31,5 (Classe 32)
A lto-falantes (RMS) (127 V CA, THD* 10 % sinal 1 KHz, Alto-falante de 8 Ohms, Nível de entrada 500 mVrms)
Resolução de tela 1 , 3 6 6 pontos (horizontal) × 7 6 8 linhas (vertical)
Entradas/Saídas
A lto-falantes/Á rea total (2) (mm) 40 × 100
CABLE/ANTENNA Terminal externo de 75 ohms para entradas RF
Dimensões
V IDEO IN V ÍDEO: 1 Vp-p, 75 ohms não balanceados, sincronização negativa com pedestal (mm) 735 × 471 × 171
Á UDIO: 500 mVrms (Típico) / Impedância: 47 Kohms sem pedestal (mm) 735 × 446 × 75,5
COMPONENT IN Y P P (Vídeo componente): Y: 1,0 Vp-p, 75 ohms não balanceado, sincronização negativa / padrão de furo de montagem
B R
P B: 0,7 Vp-p, 75 ohms / P R: 0,7 Vp-p, 75 ohms / 100 × 100
da parede (mm)
Formato do sinal: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
tamanho de parafuso de
Á UDIO: 500 mVrms (Típico) / Impedância: 47 Kohms M4 (6.5 - 10 mm)
montagem da parede (mm)
HDMI IN 1/MHL HDMI: Vídeo: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, 1080/24p
Peso
MHL: Vídeo: 480i, 480p, 576i, 576p, 720p, 720/30p, 1080i, 1080/30p, 1080/24p 5,2
com pedestal (kg)
Á udio: Dois canais lineares PCM 32, 44,1 e 48 kHz, 16, 20 e 24bits, Dolby Digital
sem pedestal (kg) 5,0
Entrada do PC

AUDIO OUT Saída de áudio, Fones de ouvido (minitomada) A cessórios fornecidos Controle Remoto RM-YD093 (1) / Pilhas tamanho AAA (2) / Manual de Instruções (1)
Guia Rápido (1) / Folheto de Instruções de Segurança (1) / Licença de Softw are (1)/Folheto Ginga (1)
USB Foto, Música e Vídeo
Guia de Montagem do Pedestal (1) / Pedestal (1 conjunto) / Parafuso (2) / Adaptador AC
Entrada DC Entrada do adaptador AC Suporte de Cabo (1) / Fixador do Adaptador AC (2)

A cessórios opcionais Cabos de Conexão/Kit de Cinto de Segurança

* Distorção Harmônica Total.
• A disponibilidade dos acessórios opcionais depende do estoque.
• Projeto e especificações técnicas sujeitos a alterações sem aviso prévio.
• Pesos e dimensões são aproximados.

KDL-32R434A 1
 SECTION 1 - SPECIFICATIONS AND LAYOUTS

BOARD LAYOUT

KDL-32R434A

MAIN BOARD
(A BOARD)

SIDE JACK
COVER

TCON

H BOARD

KDL-32R434A 2
 SECTION 1 - SPECIFICATIONS AND LAYOUTS

WIRE DRESSING

KDL-32R434A

KDL-32R434A 3
SECTION 2 - TROUBLESHOOTING Self Diagnosis
Supported model

DIAGNOSING THE ERROR SELF CHECK

Before servicing the Television:

Back <<
1. Verify the TV has the symptom the customer indicated. 002 MAIN_ POWER 001 Indicates
2. Check to see if the latest Software is installed. 003 DC_ALERT1 000 an error
003 AUDIO_PROT 000 has occurred
a. If not, install the latest version.
0 04 B A L A N C E R_ERR 000
3. Determine the replacement part required. 0 05 TC O N _E R R 000
005 PANEL_ID_NVM_ERR 000 Indicates
VIEWING THE SELF CHECK DIAGNOSIS HISTORY 0 06 B A C K LIT 000 no error
When an error is detected, the Self Check screen records the number of 0 07 T E M P _E R R 000 has occurred
times the error occurred. This is helpful in confirming past occurrences of
an error and for determining if an error is intermittent when the customer is
00116 00024 00115
not sure what is causing the television to shut down. If the screen displays
a “0”, no error has occurred. [Home] Exit

Press to turn on the TV and then turn it off again. SAMPLE SELF CHECK DIAGNOSIS PAGE
1. POWER

2. Press the following buttons on the Remote Commander within 1

second of each other:

DISPLAY Channel 5 Volume - POWER

NOTE: This differs from accessing Service Adjustments Mode (Volume +).

KDL-32R434A 4
 SECTION 2 - TROUBLESHOOTING

TRIAGE CHART
Use this general Triage Chart to determine what may possibly be causing the error before going out to the customers location.

1. Confirm the symptom from the customer. Red Dot: (Primary) Most likely defective part.
2. Select that symptom from the chart. Blue Triangle: (Secondary) Possible defective part.
3. Bring the primary component listed for that symptom.
4. Follow the associated flowcharts in the Training Manual to isolate the board.
5. Chart Color Code.

Protection Modes Power Video Audio

Board Whole Isolated

No
2X 3X 6X Dead set Screen Area No Audio
Video
Distortion Distortion

MAIN BOARD ▲ ▲
LCD PANEL

TCON ▲ ▲
*NOTE: REFER TO LCD PANEL SERVICE MANUAL IN REFERENCE LIBRARY DATABASE
FOR CORRECT REPLACEMENT PARTS BASED ON SERIAL NUMBER.

KDL-32R434A 5
 SECTION 2 - TROUBLESHOOTING

FLOWCHARTS AND DIAGRAMS

OVERALL BLOCK DIAGRAM

MAIN BOARD

CABLE/ANTENNA
L
TUNER CLASS D
RF
AUDIO
COMPONENT/ AMP
R
COMPOSITE

COMPOSITE

AUDIO L/R IN

HDMI 1 MT5580 AUDIO OUT

A/V DECODER
A/V PROCESS

LVDS
USB LCD PANEL, TCON

&
CONTROL LED BACKLIGHTS
KEYS

LED
IR RX
H

AC IN AC ADAPTER

KDL-32R434A 6
 SECTION 2 - TROUBLESHOOTING

STANDBY LED BLINKING FLOWCHART

Protect
Shutdown.
Standby LED
Blinking

Yes
2X AC Adapter*

No

Yes
3X Main Board*

No

Yes “SONY” logo No

6X appears before AC Adapter*
shutdown?

Yes

LCD Panel*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 15 .

KDL-32R434A 7
 SECTION 2 - TROUBLESHOOTING

NO VIDEO FLOWCHART

No Video

Backlights No
LCD Panel*
turned on?

Yes

Any OSD
Yes
graphics Main Board*
present?

No

Unplug LVDS
connector at
TCON while unit
Any flashes No
is running. This seen on LCD Panel*
may need to be screen?
done more than
once.
Yes

Main Board*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 15 .

KDL-32R434A 8
 SECTION 2 - TROUBLESHOOTING

VIDEO DISTORTION FLOWCHART

Video Distortion

Is distortion Yes No Yes Lines move Yes

Improper of Vertical lines Main Board*
across entire when wide-mode
missing colors? or bars?
screen? changed?

No Yes No No

Main Board* LCD Panel*

Any horizontal Yes

LCD Panel*
lines?

No

Any single or Yes

LCD Panel*
isolated vertical
lines?

No

More than 1 Yes Uneven Yes

LCD Panel*
vertical band? brightness?

No

LCD Panel*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 15 .

KDL-32R434A 9
SECTION 3 - REPAIR INFORMATION

REPAIRING THE TV REMOVING THE LOWER COVER

If the latest Software does not correct the issue, complete the following:
1. Locate and disconnect AC Power Cord.
1. Verify the television has the symptom the customer indicated.
2. Replace part causing the symptom.
3. Install the latest version of Software (Required for ALL repairs).
4. Perform the required service adjustments and checks.
5. Verify the repair resolved the issue.
2. Locate and remove all screws from the Lower Cover.
REMOVING THE TABLE-TOP STAND

1. Place TV face down on a soft and flat surface.

3. Grasp the areas shown on the Lower Cover to release the clips and lift
upwards to detach.
2. Remove 2 screws from Table-Top Stand and carefully detach from
Lower Cover.

CAUTION: Do not use the Table-Top Stand

to hold or carry the TV.

KDL-32R434A 10
 SECTION 3 - REPAIR INFORMATION

REPLACING THE MAIN BOARD

The Main Board used in these models is available for repair. For Part 6. Access Service Mode by pressing the following buttons within 1 second
Number information refer to Section 4 - Exploded View/Part Number of each other:
Information on page 15.
DISPLAY Channel 5 Volume + POWER
1. Disconnect all connectors from the Main Board.
Service Mode
Sound Adjustment >>
Wide Band Tuning >>
Range Scan' >>
Self diagnosis history >>
Status Information' >>
LVDS Spectrum(%0) <[ 30 ]>
2. Remove 6 screws from Main Board and Side Bracket.
Low of HPD <[ 5 ]>
TVD_MCDONE_CNT <[ 20 ]>
Demo Special >>
Bypass AVI Info Detect <[ On ]>
Panel Selection <[ 192_TPT315B5-XVN03 ]>
UART Selection No Log
SERIAL NUMBER EDIT
MODEL NAME EDIT
3. Slide Side Bracket, then lift Main Board to detach.
[</>]Set [Home] Exit

7. Press until Panel Selection is selected.

Service Mode
Sound Adjustment >>
4. Install the new Main Board, screws and all connectors. Wide Band Tuning >>
Range Scan' >>
5. Update the Software. Self diagnosis history >>
After ALL repairs UPDATE the SOFTWARE to the latest version. Status Information' >>
Instructions are included with the Software package on the Sony LVDS Spectrum(%0) <[ 30 ]>
Authorized website. Low of HPD <[ 5 ]>
TVD_MCDONE_CNT <[ 20 ]>
a. Insert the USB device with the latest Software into the TV. Demo Special >>
Bypass AVI Info Detect <[ On ]>
b. Press POWER to turn on the TV. Panel Selection <[ 192_TPT315B5-XVN03 ]>
UART Selection No Log
c. Wait until the Software update is complete and TV turns OFF. SERIAL NUMBER EDIT
MODEL NAME EDIT

[</>]Set [Home] Exit

KDL-32R434A 11
 SECTION 3 - REPAIR INFORMATION

8. Press or to select the correct Panel Code for theTV model. 11. Press to be able to select the first digit.
(Use the table below for reference).
Service Mode
Model Name Panel Code Sound Adjustment >>
Wide Band Tuning >>
KDL-32R434A 192_TPT315B5-XVN03 Range Scan' >>
Self diagnosis history >>
CAUTION: Select ONLY the correct Panel Code. Status Information' >>
LVDS Spectrum(%0) <[ 30 ]>
9. Locate the Serial Number for the TV on the side of the Rear Cover. Low of HPD <[ 5 ]>
TVD_MCDONE_CNT <[ 20 ]>
MODEL NO Demo Special >>
Bypass AVI Info Detect <[ On ]>
KDL-32R434A
Panel Selection <[ 192_TPT315B5-XVN03 ]>
SERIAL NO UART Selection No Log
8500001 SERIAL NUMBER EDIT _ _ _ _ _ _ _
MODEL NAME EDIT

[</>]Set [Home] Exit

10. Press until SERIAL NUMBER EDIT is selected.

Service Mode 12. Press or to select numbers and then to move to the next
Sound Adjustment >> space until Serial Number is complete.
Wide Band Tuning >>
Range Scan' >> Service Mode
Self diagnosis history >> Sound Adjustment >>
Status Information' >> Wide Band Tuning >>
LVDS Spectrum(%0) <[ 30 ]> Range Scan' >>
Low of HPD <[ 5 ]> Self diagnosis history >>
TVD_MCDONE_CNT <[ 20 ]> Status Information' >>
Demo Special >> LVDS Spectrum(%0) <[ 30 ]>
Bypass AVI Info Detect <[ On ]> Low of HPD <[ 5 ]>
Panel Selection <[ 192_TPT315B5-XVN03 ]> TVD_MCDONE_CNT <[ 20 ]>
UART Selection No Log Demo Special >>
SERIAL NUMBER EDIT Bypass AVI Info Detect <[ On ]>
MODEL NAME EDIT Panel Selection <[ 192_TPT315B5-XVN03 ]>
UART Selection No Log
[</>]Set [Home] Exit SERIAL NUMBER EDIT 8500001
MODEL NAME EDIT

[</>]Set [Home] Exit

CAUTION: The Serial Number can only be selected once. Be sure

to verify the information is correct before saving the changes.

KDL-32R434A 12
 SECTION 3 - REPAIR INFORMATION

13. When the complete Serial Number displays, press . 16. Press to be able to select the first character.

14. On the confirmation screen, press to select YES and then . Service Mode
Sound Adjustment >>
Input Data Correct? Wide Band Tuning >>
Range Scan" >>
Self diagnosis history >>
Status Information" >>
Yes No LVDS Spectrum(%0) <[ 30 ]>
Low of HPD <[ 5 ]>
TVD_MCDONE_CNT <[ 20 ]>
Demo Special >>
Bypass AVI Info Detect <[ On ]>
Selected text displays in black Panel Selection <[ 192_TPT315B5-XVN03 ]>
UART Selection No Log
15. Press until MODEL NAME EDIT is selected. SERIAL NUMBER EDIT 8500001
MODEL NAME EDIT _ _ _ _ _ _ _ _ _ _ _
Service Mode
Sound Adjustment >> [</>]Set [Home] Exit
Wide Band Tuning >>
Range Scan" >>
Self diagnosis history >> 17. Press or to select characters and then to move to the next
Status Information" >>
space until Model Name is complete.
LVDS Spectrum(%0) <[ 30 ]> NOTE: Make sure to include dash in Model Name.
Low of HPD <[ 5 ]>
TVD_MCDONE_CNT <[ 20 ]> Service Mode
Demo Special >> Sound Adjustment >>
Bypass AVI Info Detect <[ On ]> Wide Band Tuning >>
Panel Selection <[ 192_TPT315B5-XVN03 ]> Range Scan" >>
UART Selection No Log Self diagnosis history >>
SERIAL NUMBER EDIT 8500001 Status Information" >>
MODEL NAME EDIT LVDS Spectrum(%0) <[ 30 ]>
Low of HPD <[ 5 ]>
[</>]Set [Home] Exit TVD_MCDONE_CNT <[ 20 ]>
Demo Special >>
Bypass AVI Info Detect <[ On ]>
Panel Selection <[ 192_TPT315B5-XVN03 ]>
UART Selection No Log
SERIAL NUMBER EDIT 8500001
MODEL NAME EDIT KDL-32R434A

[</>]Set [Home] Exit

CAUTION: The Model Name can only be selected once. Be sure

to verify the information is correct before saving the changes.

KDL-32R434A 13
 SECTION 3 - REPAIR INFORMATION

18. When the complete Model Name displays, press .

REMOVING THE BEZEL AND H BOARD

19. On the confirmation screen, press to select YES and then . 1. Use a small and narrow tool to release H Board from Bezel.

Input Data Correct?

Yes No

2. Disconnect the connector from the H Board to detach.

Selected text displays in black

20. Press POWER to exit Service Mode.

REMOVING THE SPEAKERS

1. Lift and remove Speakers, then disconnect connectors to detach. 3. Place the TV face up, then grasp the Bezel carefully on the shown areas
to release from LCD Panel and lift to detach.

2. Locate and remove 2 screws from Speaker Cover. Twist downwards to

release clips from the Bezel.

KDL-32R434A 14
SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

KDL-32R434A Compone nts not ide ntifie d by a part numbe r or de scription The compone nt parts of an asse mbly are indicate d by the re fe re nce numbe rs in
are not stocke d be cause the y are se ldom re quire d for routinethe far right column of the parts list and within the dotte d line s of the diagram.
se rv ice .

NOTE: The compone nts ide ntifie d by shading and

!
NOTE: The compone nts ide ntifie d by a re d outline and a mark contain confide ntial
mark are critical for safe ty. information. Spe cific instructions must be adhe re d to whe ne v e r the se compone nts are
Re place only with part numbe r spe cifie d. re paire d and/or re place d. (Se e Appe ndix A)

REF. NO. PART NO. DESCRIPTION

1 NA LCD PANEL
FOR ALL LCD PANEL AND TCON BOARD PART NUMBER
INFORMATION REFER TO THE LCD PANELS SERVICE MANUAL

2 4-485-012-01 SIDE JACK COVER

3 1-895-502-11 A BOARD, COMPLETE

AFTER REPLACING THE MAIN BOARD, YOU MUST UPDATE
THE SOFTWARE TO THE LATEST VERSION.

4 1-492-702-11 AC ADAPTER
! 5 1-848-037-11 POWER SUPPLY CORD
1

6 4-485-011-01 LOWER COVER (UNDER COVER)

7 4-479-429-01 STAND SHAFT

7
4

KDL-32R434A 15
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

KDL-32R434A NOTE: The compone nts ide ntifie d by shading and

!
NOTE: The compone nts ide ntifie d by a re d outline and a mark contain confide ntial
mark are critical for safe ty. information. Spe cific instructions must be adhe re d to whe ne v e r the se compone nts are
Re place only with part numbe r spe cifie d. re paire d and/or re place d. (Se e Appe ndix A)

REF. NO. PART NO. DESCRIPTION

51 4-470-954-01 BRACKET VESA

51 52 4-485-009-01 BEZEL
51 53 1-895-413-11 H BOARD, MOUNTED

54 4-470-953-01 BRACKET STAND

55 4-485-010-01 SP COVER
56 1-858-956-11 LOUD SPEAKER
52

53

Bracket MB Top*

56 54
Bracket MB Btm*

55

*Reinstall Bracket MB Top and Bracket

56
MB Btm w hen replacing the Main Board.

KDL-32R434A 16
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

CONNECTORS NOTE: The compone nts ide ntifie d by shading and

!
NOTE: The compone nts ide ntifie d by a re d outline and a mark contain confide ntial
mark are critical for safe ty. information. Spe cific instructions must be adhe re d to whe ne v e r the se compone nts are
Re place only with part numbe r spe cifie d. re paire d and/or re place d. (Se e Appe ndix A)

KDL-32R434A

101

102

103

REF. NO. PART NO. DESCRIPTION

101 1-910-109-12 LVDS CABLE 32 MB-TCON 30P

102 1-910-109-11 CONNECTOR ASSEMBLY 32 MB-IR 6P
103 1-910-109-10 CONNECTOR ASSEMBLY 32 MB-SP LR 4P

KDL-32R434A 17
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

SCREWS NOTE: The compone nts ide ntifie d by shading and

!
NOTE: The compone nts ide ntifie d by a re d outline and a mark contain confide ntial
mark are critical for safe ty. information. Spe cific instructions must be adhe re d to whe ne v e r the se compone nts are
Re place only with part numbe r spe cifie d. re paire d and/or re place d. (Se e Appe ndix A)

P/N DESCRIPTION KDL-32R434A

Lower Cover Terminal (1),

7-685-646-79 SCREW, +BVTP 3X8 TYPE2 IT-3
Speaker Cover (3)

2-580-638-01 SCREW, +BVTP2 4X8 Speaker Cover (2)

Speaker Cover (2), Lower Cover (8),

7-685-660-79 SCREW +BVTP 4X10 TYPE2 IT-3
Stand Bracket (4)

2-580-640-01 SCREW, +BVTP 4X16 TYPE2 IT-3 Lower Cover (2)

4-466-880-01 SCREW, M5X18 SW (IRST) Table-Top Stand to TV (2)

Lower Cover (1), Main Board (4), Stand Bracket (2),

4-466-881-01 SCREW, M3X10 SW (FANT) MB Bracket Top (2), MB Bracket Bottom (2),
Vesa Brackets (6), Side Jack Cover (2)

KDL-32R434A 18
SECTION 5 - ACCESSORIES/PART NUMBER INFORMATION

ACCESSORIES AND PACKAGING

PART NO. DESCRIPTION

4-466-880-01 SCREW, M5X18 SW

(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV.
CAUTION: These screws cannot be used to secure the TV to the Wall
Mount Brackets.

4-476-481-41 MANUAL, INSTRUCTION

4-476-482-41 GUIDE, QUICK SET UP
4-262-708-04 CLAMPER, CABLE

OPTIONAL ACCESSORIES
PART NO. DESCRIPTION

4-414-470-01 SUPPORT BELT KIT

REMOTE COMMANDER
PART NO. DESCRIPTION

1-492-066-21 REMOTE COMMANDER (RM-YD093)

KDL-32R434A 19
APPENDIX A: ENCRYPTION KEY COMPONENTS

Encryption key components developed by Sony Corporation contain confidential information and shall be handled under the non-disclosure obligations provided
in the applicable agreement with Sony Corporation (and/or its subsidiary).
As part of this agreement specific instructions must be adhered to whenever a Circuit Board containing encryption key components is repaired and/or replaced
pursuant to the following:

1. In the service manual the Circuit Board(s) containing encryption key components shall be identified with a red outline and a .

2. Only repair boards or components listed in the service manual shall be utilized for replacement and/or repair.

3. Disassembly, decryption or reverse-engineering component(s) is strictly prohibited.

4. Any board in which the Servicer replaces an encryption key component must be placed back into the set it orignally came from and the replaced
defective component MUST BE DESTROYED. Boards cannot be swapped.

5. If a Circuit Board identified with a red outline and a in the service manual is deemed to be defective:
and if a core charge is imposed and is covered under the product warranty, the defective un-repaired or modified board MUST BE RETURNED to
a.
Sony.
b. and if the core charge is NOT covered under the product warranty, the defective un-repaired or modified board MUST BE DESTROYED.

6. If a unit is destroyed (such as field scrap), the Circuit Board identified with a red outline and a in the service manual MUST BE DESTROYED.

is a trademark of Sony Electronics.

Reproduction in whole or part without written permission is prohibited. All rights reserved.
Sony Corporation
Sony LCSC English
Technical Services 2013IJ74WEB-1
9-883-540-01 Service Publications Department © 2013.9

KDL-32R434A A-1