Data Communication & Computer Networks 2016-EE-113

Lab#04
Object:

1) To assign IP address on fast ethernet interface.

2) To assign Ip address on serial interface.
3) Verify the connectivity by using PING command.
4) Assignment Task.
Task A

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!
Router>en
Router#config t
Router(config)#int fa0/0
Router(config-if)#ip add 10.0.0.1 255.0.0.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#exit
Router#ping 10.0.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:
Success rate is 80 percent (4/5), round-trip min/avg/max = 0/13/51 ms
Router#ping 10.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/14/53 ms

Show Protocols
Router#show protocols
Global values:
Internet Protocol routing is enabled
FastEthernet0/0 is up, line protocol is up
Internet address is 10.0.0.1/8

Show Interfaces
Router#show interfaces
FastEthernet0/0 is up, line protocol is up (connected)
Hardware is Lance, address is 000a.418c.2d83 (bia 000a.418c.2d83)
Internet address is 10.0.0.1/8
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00,
Last input 00:00:08, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 4 bits/sec, 0 packets/sec
5 minute output rate 4 bits/sec, 0 packets/sec
4 packets input, 512 bytes, 0 no buffer
Data Communication & Computer Networks 2016-EE-113

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
4 packets output, 512 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

Show ip route
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, FastEthernet0/0

Show flash
Router#show flash
System flash directory:
File Length Name/status
3 5571584 c2600-i-mz.122-28.bin
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[5827403 bytes used, 58188981 available, 64016384 total]
63488K bytes of processor board System flash (Read/Write)

Task B

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se1/0
Router(config-if)#clock rate 64000
Router(config-if)#ip add 10.0.0.1 255.0.0.0
Router(config-if)#no shut

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se1/0
Router(config-if)#ip add 10.0.0.2 255.0.0.0
Router(config-if)#no shut
Data Communication & Computer Networks 2016-EE-113

%LINK-5-CHANGED: Interface Serial1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up

Ping
Router#ping 10.0.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/28/134 ms
Router#ping 10.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/13 ms

Show interfaces
Router#show interfaces
FastEthernet0/0 is administratively down, line protocol is down (disabled)
Hardware is Lance, address is 0000.0cea.4bc7 (bia 0000.0cea.4bc7)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00,
Last input 00:00:08, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial1/0 is up, line protocol is up (connected)
Hardware is HD64570
Internet address is 10.0.0.2/8
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 15 bits/sec, 0 packets/sec
5 minute output rate 15 bits/sec, 0 packets/sec
15 packets input, 1920 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
15 packets output, 1920 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
Data Communication & Computer Networks 2016-EE-113

0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Show ip route
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, Serial1/0

Show protocols
Router#show protocols
Global values:
Internet Protocol routing is enabled
FastEthernet0/0 is administratively down, line protocol is down
Serial1/0 is up, line protocol is up
Internet address is 10.0.0.2/8
Serial1/1 is administratively down, line protocol is down
Serial1/2 is administratively down, line protocol is down
Serial1/3 is administratively down, line protocol is down

Show flash
Router#show flash
System flash directory:
File Length Name/status
3 5571584 c2600-i-mz.122-28.bin
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[5827403 bytes used, 58188981 available, 64016384 total]
63488K bytes of processor board System flash (Read/Write)

Assignment Task

Router 0

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se1/0
Router(config-if)#clock rate 64000
Router(config-if)#ip add 10.0.0.1 255.0.0.0
Router(config-if)#no shut
Data Communication & Computer Networks 2016-EE-113

%LINK-5-CHANGED: Interface Serial1/0, changed state to down

%LINK-5-CHANGED: Interface Serial1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
Router(config-if)#exit
R
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/4/15 ms
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 11.0.0.1 255.0.0.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#ping 11.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 11.0.0.1, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/8/12 ms

Show Protocols
Router#show protocols
Global values:
Internet Protocol routing is enabled
FastEthernet0/0 is up, line protocol is up
Internet address is 11.0.0.1/8
Serial1/0 is up, line protocol is up
Internet address is 10.0.0.1/8
Serial1/1 is administratively down, line protocol is down
Serial1/2 is administratively down, line protocol is down
Serial1/3 is administratively down, line protocol is down

Show interfaces
Router#show interfaces
FastEthernet0/0 is up, line protocol is up (connected)
Hardware is Lance, address is 00e0.a3a0.0731 (bia 00e0.a3a0.0731)
Internet address is 11.0.0.1/8
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00,
Last input 00:00:08, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
0 output buffer failures, 0 output buffers swapped out
Serial1/0 is up, line protocol is up (connected)
Hardware is HD64570
Internet address is 10.0.0.1/8
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Data Communication & Computer Networks 2016-EE-113

Available Bandwidth 96 kilobits/sec

5 minute input rate 0 bits/sec, 0 packets/sec
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Show Ip route
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, Serial1/0
C 11.0.0.0/8 is directly connected, FastEthernet0/0

Show Flash
Router#show flash
System flash directory:
File Length Name/status
3 5571584 c2600-i-mz.122-28.bin
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[5827403 bytes used, 58188981 available, 64016384 total]
63488K bytes of processor board System flash (Read/Write)

Router 1
Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se0/1
%Invalid interface type and number
Router(config)#int se1/0
Router(config-if)#ip add 10.0.0.2 255.0.0.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
Router(config-if)#exit
Router(config)#exit

Show interfaces
Router#show interfaces
FastEthernet0/0 is administratively down, line protocol is down (disabled)
Hardware is Lance, address is 000c.cf88.ccac (bia 000c.cf88.ccac)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
Data Communication & Computer Networks 2016-EE-113

0 output buffer failures, 0 output buffers swapped out

Serial1/0 is up, line protocol is up (connected)
Hardware is HD64570
Internet address is 10.0.0.2/8
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Show ip route
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, Serial1/0

Show Flash
Router#show flash
System flash directory:
File Length Name/status
3 5571584 c2600-i-mz.122-28.bin
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[5827403 bytes used, 58188981 available, 64016384 total]
63488K bytes of processor board System flash (Read/Write)

Router 2
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#fa0/0
% Invalid input detected at '^' marker.
Router(config)#int fa0/0
Router(config-if)#ip add 10.0.0.3 255.0.0.0
Router(config-if)#no shut

Show Ip route
Router#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, FastEthernet0/0
Data Communication & Computer Networks 2016-EE-113

Show Protocols
Router#show protocols
Global values:
Internet Protocol routing is enabled
FastEthernet0/0 is up, line protocol is up
Internet address is 10.0.0.3/8

Show Interfaces
Router#show interfaces
FastEthernet0/0 is up, line protocol is up (connected)
Hardware is Lance, address is 0060.2fb5.a2be (bia 0060.2fb5.a2be)
Internet address is 10.0.0.3/8
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00,
Last input 00:00:08, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: fifo
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

Show Flash
Router#show flash
System flash directory:
File Length Name/status
3 5571584 c2600-i-mz.122-28.bin
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[5827403 bytes used, 58188981 available, 64016384 total]
63488K bytes of processor board System flash (Read/Write)