PRODUCT CATALOG 2014

COILED TUBING TOOLS

&

ACCESSORIES

1
SICONSA designs, manufactures, rents and sells specialty oil tools for coiled tubing,
wireline, snubbing, and completions. SICONSA is the pioneer of vertical manipulating
tools to release and catch without rotation. Most of our tools are patented.
Innovation is practiced daily at SICONSA where our staff strives to stay on the leading
edge of coiled tubing technology. Customized and specialty tool designs can be
manufactured to meet your unique requirements.

QUALITY STATEMENT
SICONSA is committed to providing products and services in compliance with the
Quality Program that meet our exceed or customers’ requirements, free from
deficiencies.

The management of SICONSA is dedicated to continual improvement, training, and

abiding by procedures that will ensure quality performance.

Quality is the responsibility of every employee and success is accomplished by a united

effort.

2
RENTAL TOOLS
SICONSA rental tools are inspected, completely redressed, and tested after every job.
This ensures consistent performance on every job. Training sessions at your site or ours
are available.
Our staff is on call to answer your questions, satisfy your requirements and offer
technical assistance.

We can effectively provide rentals to the entire Gulf of Mexico and most oilfield locations
worldwide. Tools can be rented or purchased from our main office in Houma, Louisiana,
or form one of our consignment vendors. Contact us for the supplier nearest your
location.

MANUFACTURING
SICONSA is the oldest manufacturing company in this business. With over 30 years of
successful tool performance for most major oil companies, independents, and service
companies, our product line remains the most unique in the industry.

INSPECTION, TESTING, & DESIGN

3
Quality and safety are top priorities at SICONSA. Our proven, patented tools are
manufactured, inspected and tested using quality procedures to ensure consistent down
hole operation.

A complete inspection of all rental tools is performed before shipping. Each tool is
tagged and accompanied by an inspection certificate. Pressure testing and function
testing are performed when the tool is prepared for shipment.

Innovation is practiced daily at SICONSA where our Engineering Department strives to

stay on the leading edge of Thru-Tubing technology. Customized and specialty
designed tools can be manufactured to meet you unique requirements.

4
General Terms and Conditions
Policy

The SICONSA Products are received by the buyer “AS IS” and SICONSA does not warrant that they can
be used for any particular purpose. Any article manufactured by SICONSA which is not free of defective
material and workmanship in the opinion of SICONSA, may be returned within six (6) months after the
date of sale for replacement. SICONSA’s liability shall be limited to replacement FOB Houma, LA, of the
part or parts shown to be defective, transportation prepaid.

Where there may be defective parts not wholly of SICONSA manufacture, our liability shall exist only to
the extent that it is able to recover form its supplier for the same defects. All products are subject to
SICONSA’s manufacturing standards. SICONSA reserves the right to make the final decision in all
questions.

Change of Design

SICONSA expressly reserves the right to change or modify the design and construction of any product, in
due course of our manufacturing procedure, without incurring any obligation or liability to furnish or install
such changes, modifications or improvements on products previously or subsequently made.

Prices

Prices do not include sales taxes or taxes not levied on the seller. All taxes based upon the freight
charges made for, or the cash receipt for the sale of products enumerated shall be added to the stated
price. List prices are subject to change without notice. Prices are U.S. currency.

Quotations

Quotations are for prompt acceptance only, unless a definite period of time is stated within which
acceptance may be made. Requests for quotations on products for export shipment should be sent
direct to the SICONSA office in Houma, LA.

Delivery

Delivery promises on all orders are given as accurately as possible and every effort will be made to make
shipment as promised, but we do not guarantee to do so and will assume no liability for damages arising
out of failure to do so.

Cancellations, Claims and Returns

Orders for products or parts of special design, size or materials are not subject to cancellation after
having been received at our factory. Claims for shortage or reductions or erroneous charges must be
presented within thirty (30) days after receipt of products.

No assembly or parts will be taken back and credited, or replaced unless arrangements for such return
have been previously made. After permission for such return is granted, a charge of twenty percent (20%)
will be assessed for restocking. A credit will be issued for tools lost in hole, when returned, after
inspection by SICONSA, in accordance to the condition of the tool(s).

5
 The SICONSA External Quick Connector is used to
connect a BHA to the end of Coiled Tubing. Torque
transmission is provide by notching the end of the pipe.
The notched pipe aligns with lugs in the connector.

DESIGN FEATURES

•Torque Transmitting
•Split Wickered Slips
•Sealed for Circulation

The Connector Template facilitates

application of the pipe notches.

EXTERNAL QUICK CONNECTOR

ASSEMBLY QC-1-562-0 QC1- QC-1-800-0 QC-2-250-0 QC-2-500-0 QC-2-750-0

PART NO. 750-00

NOMINAL OD (in) 1.562 1.750 1.800 2.250 2.500

2.750
ACTUAL OD (in) 1.562 1.750 1.800 2.250 2.500 2.750
MINIMUM ID (in) 0.750 0.750 0.750 1.000 1.000 1.000
OVERALL 11.06 11.44 12.35 13.06 13.06 13.06
LENGTH (in)
MAKE UP 8.88 9.25 10.16 10.88 10.88 10.88
LENGTH (in)
WEIGHT (lb) 3 4 4 7 8 9
MAXIMUM WORK 51,470 60,645 56,819 69,000 105,000 120,000
LOAD (yield lb)
PRESSURE 21,063 29,118 12,915 10,000 10,000 10,000
RATING (psi)
TORQUE 200 350 350 400 500 550
CAPACITY (ft-lb)
STANDARD CONNECTION: 1" CSH EQUIV. 1" CSH EQUIV. 1" CSH EQUIV. 1-1/4" CSH EQUIV. 1-1/4" CSH
EQUIV. 1-1/4" CSH EQUIV.
MAKE UP 400 400 400 600 600 600
TORQUE (ft-lb)
COILED TUBING 1 1 1 1/4 1 1/2 1 3/4 2
SIZE (in)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

6
 The SICONSA Grub Screw Quick Connector is used
to connect a BHA to the end of Coiled Tubing. Grub
screws dimple the pipe and provide for torque
transmission.

DESIGN FEATURES
•Torque Transmitting
•Split Wickered Slips
•Sealed for Circulation

GRUB SCREW CONNECTOR

Assembly Part GQC-1-562-0 GQC-1-750-0 GQC-1-687-0 GQC-1-800-0 GQC-2-250-0 GQC-2-500-0 GQC-2-750-0

Number
Coil Size: 1.000 1.000 1.250 1.250 1.500 1.750 2.000
Nominal O.D.: 1.562 1.750 1.687 1.800 2.250 2.500 2.750
Minimum I.D.: 0.750 0.750 0.750 0.750 1.000 1.000 1.000
Overall Length 10.875 11.375 12.312 12.312 13.062 13.000 13.000
(in.):
Makeup Length 8.687 9.187 10.125 10.125 10.875 10.812 10.812
(in.):
Weight (Lbs.): 3 4 4 4 7 8 9
Torque Capacity: 200 125 350 350 400 500 550
Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs
Maximum Work 56,000 67,000 48,500 60,500 69,000 105,000 120,000
Load (Yield):
Pressure Rating: 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS 1" CS Hydril 1" CS 1" CS 1-1/4" CS 1-1/4" CS 1-1/4" CS
Connection**: Hydril Equivalent Hydril Hydril Hydril Hydril Hydril
Equivalent Equivalent Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 300-400 300-400 300-400 400-600 400-600 400-600
(Ft-Lbs):

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

7
The SICONSA Grub Internal Quick Connector is used to
connect a BHA to the end of Coiled Tubing. Slips which
engage the I.D. of the pipe allow for reduction of the
connector O.D. dimension. Internal connectors are used
when a restriction in the well does not permit usage of
conventional external connectors.

DESIGN FEATURES
•Torque Transmitting
•Split Wickered Slips
•Sealed for Circulation

The Connector Template facilitates

application of the pipe notches.

INTERNAL QUICK CONNECTOR

Assembly Part IQC-1-600-0 IQC-1-800-0 IQC-2-125-0 IQC-2-250-0

Number
Coil Size 1.250 1.500 1.750 2.000
Nominal O.D. 1.600 1.800 2.125 2.250
Minimum I.D.: 0.500 0.625 0.812 1.062
Overall Length (in.): 14.000 14.250 15.750 15.750
Makeup Length (in.): 11.812 12.063 13.562 13.562
Weight (Lbs.) 4 4 7 8
Torque Capacity 250 Ft-Lbs 300 Ft-Lbs 350 Ft-Lbs 400 Ft-Lbs
Maximum Work 23,000 51,000 63,000 72,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent

Make-up Torque 300-400 300-400 400-600 400-600

(Ft-Lbs)
•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

8
The SICONSA Dual Flapper Valve prevents well pressure
from entering the work string. Flappers allow for passage
of balls to operate equipment installed below the flappers.

DESIGN FEATURES
•Metal & Elastomer Sealing Surfaces
•Replaceable Flapper Cartridges
•Torsion Spring Closure

DUAL FLAPER VALVE

Assembly Part Number CFV-1-687-0 CFV-1-750-0 CFV-2-125-0 CFV-2-750-0

Nominal O.D. 1.687 1.750 2.125 2.750

Minimum I.D. 0.688 0.688 1.020 1.020
Overall Length (in.) 12.187 12.187 13.187 14.187
Makeup Length (in.) 10.000 10.000 11.000 12.000
Weight (Lbs.) 8 12 21 38
Maximum Work Load 37,500 51,500 78,500 155,200
(Yield)
Pressure Rating 10000 10000 10000 10000
Standard Tubing 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent

Make-up Torque 300-400 300-400 400-600 400-600

(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

9
 Bottom Hole Assemblies may become lodged in the well
bore. The SICONSA Hydraulic Disconnect is installed in a
work string directly above the BHA. Circulating a ball to
the disconnect and applying pressure to a pre determined
value will cause the upper section and the lower section of
the disconnect to separate. Once separated, the pipe and
upper portion of the disconnect can be retrieved. The
lower portion of the disconnect remains attached to the
stuck BHA providing an internal fishing neck for
subsequent attempts at retrieval.

DESIGN FEATURES
•Torque Transmitting

Standard Internal Pulling Tools

will engage the lower disconnect
section.

INTERNAL HYDRAULIC DISCONNECT

Assembly Part HDI-1-562-0 HDI-1-750-0 HDI-2-125-0 HDI-2-375-0 HDI-2-875-0
Number
Nominal O.D. 1.562 1.750 2.125 2.375 2.875
Minimum I.D. 0.375 0.531 0.562 0.562 0.875
Effective Area 0.441 0.785 1.484 1.484 2.760
( sq. in.)
Recommended Ball 0.500 0.562 0.625 0.625 1.000
Size (in.)
Overall Length (in.) 19.750 19.750 20.000 20.000 23.425
Makeup Length (in.) 17.550 17.550 17.812 17.812 21.250
Weight (Lbs.) 6 8 13 15 25
Internal Fishing Neck 1-1/2 GS Equiv. 2 GS Equiv. 2-1/2 GS Equiv. 2-1/2 GS Equiv. 3 GS Equiv.
Torque Capacity 450 Ft-Lbs 525 Ft-Lbs 575 Ft-Lbs 575 Ft-Lbs 1,100 Ft-Lbs
Maximum Work 26,500 33,000 58,000 68,000 80,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 300-400 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

10
 Bottom Hole Assemblies may become lodged in the well bore.
The SICONSA External Hydraulic Disconnect is installed in a
work string directly above the BHA. Circulating a ball to the
disconnect and applying pressure to a pre determined value
will cause the upper section and the lower section of the
disconnect to separate. Once separated, the pipe and upper
portion of the disconnect can be retrieved. The lower portion
of the disconnect remains attached to the stuck BHA providing
an external fishing neck for subsequent attempts at retrieval.

DESIGN FEATURES
•Torque Transmitting
•External Fish Neck
•Adjustable Shear Value
•Open Circulation Path after Shearing

An Overshot will engage the lower disconnect section

EXTERNAL HYDRAULIC DISCONNECT
Assembly Part HR-1-562-0 HR-1-687-0 HR-1-800-0 HR-2-125-0 HR-2-700-0 HR-3-125-0
Number
Nominal O.D. 1.562 1.687 1.800 2.125 2.700 3.125
Minimum I.D. 0.312 0.312 0.312 0.500 0.750 1.000
Effective Area 0.785 0.785 0.785 1.227 2.074 2.579
( sq. in.)
Recommended 0.437 0.437 0.562 0.625 0.875 1.125
Ball Size (in.)
Overall Length 20.687 20.687 20.687 21.312 21.812 23.750
(in.)
Makeup Length 18.500 18.500 18.500 19.125 19.625 21.563
(in.)
Weight (Lbs.) 8 9 10 11 21 27
External Fishing 1.187 x 4.375 1.187 x 4.375 1.250 x 4.375 1.500 x 4.375 2.000 x 4.375 2.625 x 4.375
Neck
Torque Capacity 175 Ft-Lbs. 275 Ft-Lbs. 375 Ft-Lbs. 500 Ft-Lbs. 1,000 Ft-Lbs. 850 Ft-Lbs.
Maximum Work 31,000 31,000 31,000 36,000 71,000.00 134,500.00
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection ** Equivalen Equivalen Equivalen Equivalen Equivalen Equivalen
Make-up Torque 300-400 300-400 300-400 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

11
SAFETY HYDRAULIC RELEASE

The SICONSA Safety Hydraulic Release is a component of

the Taylor Made Motor Head Assembly. The individual
Safety Hydraulic Release can be adapted to the standard
Motor Head Assembly. This design of Hydraulic Release
utilizes splines and grooves for torque transmission rather
than tabs. An adjustment nut takes up any slack from wear
or machining tolerances. Eliminating slack prevents
movement that can result in fatigue failure. A lock ring
replaces the more conventional collet or dog/window design.
The modular design provides versatility of ball seat and ball
size selection, top and bottom connections, installation of
other components, and shear value. Circulation ports and
shear screw holes through body parts are eliminated thus
preventing potential leaks. Once separated, the abandoned
fish neck can be latched with standard pulling tools.

DESIGN FEATURES
•Prevents Fatigue Due to Slack
•Fish Neck Free of Tabs
•No External Holes Through Body Parts
•Adapts to Motor Head Assembly

SAFETY HYDRAULIC RELEASE

ASSEMBLY PART NO. 1-687-HR-00 2-125-HR-00 2-875-HR-00
NOMINAL OD (in) 1.687 2.125 2.875
ACTUAL OD (in) 1.687 2.125 2.875
MINIMUM ID (in) 0.635 0.688 0.625
OVERALL LENGTH (in) 19.24 20.73 24.78
MAKE UP LENGTH (in): 17.05 18.54 22.59
WEIGHT (lb)
MAXIMUM WORK LOAD (yield lb 37,306 63,451 120,605
PRESSURE RATING (psi) 11,899 10,327 10,822
TORQUE CAPACITY (ft-lb) 590 1,331 2,717

TEMPERATURE RATING (deg. F -20/+550 -20/+550 -20/+550

STANDARD CONNECTION 1" CSH 1-1/4" CSH 2 -3/8" PAC

MAKE UP TORQUE (ft-lb) 300-400 400-600 2,400

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request

12
The SICONSA Motor Head Assembly features a completely
redesigned hydraulic disconnect and replaceable flapper cartridges.

The new style disconnect utilizes a tensioning nut to eliminate slack

between the upper and lower disconnect sections. Tensional load is
transferred to the tool body rather than a collet or lug cage. separation
of the components for individual usage or a variety of assembly
configurations. The full assembly includes an external connector, dual
flapper valve, hydraulic disconnect, ball drop circulating valve, and
rupture disc sub. Each of these components can be eliminated from the
assembly or utilized individually.

DESIGN FEATURES
•Torque Transmitting
•Modular Design
•Internal Fish Neck
•No Torque Tabs on Fish Neck
•Slack Adjustment

MOTOR HEAD ASSEMBLY

ASSEMBLY PART NO. MHA-1-687-0 MHA-2-125-00 MHA-2-875-0

NOMINAL OD (in) 1.687 2.125 2.875
ACTUAL OD (in) 1.687 2.125 2.875
MINIMUM ID (in) BALL SEAT ID BALL SEAT ID BALL SEAT ID
OVERALL LENGTH (in) 32.63 34.68 42.62
MAKE UP LENGTH (in) 30.50 32.43 40.25
WEIGHT (lb) 20 60
MAXIMUM WORK LOAD 31,500 63,451 120,605
(yield lb)
PRESSURE RATING (psi) 11,900 10,327 10,822
TORQUE CAPACITY (ft-lb) 600 1,331 2,717
STANDARD CONNECTION 1" CSH EQUIV. 1 1/4" CSH EQUIV. 2 3/8" PAC
MAKE UP TORQUE (ft-lb) 300-400 400-600 2,400

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

13
The SICONSA VR (Vibration Resistant) Shear Sub
provides a means of emergency disconnect with straight
pull force. When used with a motor, the compensator
section prevents vibration from working against the shear
screws. Piston areas are designed to prevent pressure
differential from creating force toward separation. Once
separated, an internal
fishing is provided for subsequent retrieval attempts.

DESIGN FEATURES
•Torque Transmitting
•Vibration Resistant
•Pressure Balanced
•Internal Fishing Neck
•Adjustable Shear Value

VR SHEAR SUB
Assembly Part Number VRSS-1-750-0 VRSS-1-800-0 VRSS-2-125-0
Nominal O.D. 1.750 1.800 2.125
Minimum I.D. 0.687 0.687 0.750
Overall Length (in.) 11.532 11.532 16.125
Makeup Length (in.) 9.320 9.320 13.937
Weight (Lbs.) 5 7 11
Internal Fishing Neck 2 GS Equiv. 2 GS Equiv. 2-1/2 GS Equiv.
Torque Capacity 600 Ft-Lbs 600 Ft-Lbs 800 Ft-Lbs
Maximum Work Load 35,000 35,000 40,000
(Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 300-400 400-600

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

14
SICONSA Knuckle Joints provide tool string flexibility
and pressure integrity. The knuckle joint can be used as a
swivel joint while assembling a tool string or used to assist
alignment of retrieval tools with fish. The knuckle tension
can be easily adjusted by the tension lock nut.

DESIGN FEATURES
•Adjustable Knuckle Tension
•Pump Through Sealed

KNUCKLE JOINT
Assembly Part Number KJ-1-750-0 KJ-2-250-0 KJ-2-625-0 KJ-3-500-0
Nominal O.D. 1.750 2.250 2.625 3.500
Minimum I.D. 0.250 0.375 0.500 1.000
Overall Length (in.) 13.250 13.375 13.375 16.000
Makeup Length (in.) 11.062 11.187 11.187 13.812
Weight (Lbs.) 8 10 13 27
Maximum Work Load 52,500 125,000 160,000 205,000
(Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 400-600 400-600 400-600

•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

15
MECHANICAL UP & DOWN JAR
The SICONSA Mechanical up & down Jar delivers both upward and downward impact.
Upward impact is achieved by upward strain sufficient to overcome the selected up
release setting.
Downward impact is achieved by applying downward compression sufficient to
overcome the selected down release setting.

Either upward or downward impact can be delivered by returning the jar to neutral
weight and then applying strain or compression in the direction of desired impact

The upward and downward release setting are independent and adjusted separately

DESIGN FEATURES
•Fully Mechanical
•Not Affected by Temperature
•Not Affected by Pressure
•Up & Down Impact
•Sealed for Circulation
•Torque Transmitting
•Not dependent on Seals for Performance

16
As s embly Part UDJ-1-562-0 UDJ-1-660-0 LDUDJ-1-812-0 UDJ-1-812-0 UDJ-2-250-0 UDJ-2-700-0 UDJ-3-125-0
Number
Nominal O.D. 1.562 1.660 1.812 1.812 2.250 2.700 3.125
Minimum I.D. 0.250 0.250 0.562 0.250 0.312 0.562 1.000
Overall Length - 6' 9-1/2" 6' 9-1/2" 6' 11-3/4" 6' 11-3/4" 7' 1" 7' 7" 11' 2"
CLOSED
Overall Length - 7' 3" 7' 3" 8' 0-1/4" 8' 0-1/4" 8' 1" 8' 7-1/2" 12' 0"
OPEN
Makeup Length- 6' 7-5/16" 6' 7-5/16" 6' 9-5/16" 6' 9-5/16" 6' 10-13/16" 7' 4-13/16" 11' 8-27/32"
CLOSED
Makeup Length - 7' 0-13/16" 7' 0-13/16" 7' 10-1/16" 7' 10-1/16" 7' 10-13/16" 8' 5-5/16" 11' 8-27/32"
OPEN
Weight (Lbs .) 41 42 48 48 77 119 224
Torque Capacity 400 Ft-Lbs 400 Ft-Lbs 400 Ft-Lbs 400 Ft-Lbs 1,100 Ft-Lbs 1,900 Ft-Lbs 6,500 Ft-Lbs
Maximum W ork 40,000 40,000 42,500 45,000 105,000 130,000 200,000
Load (Yield)
Pres s ure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1" CS Hydril 1" CS Hydril 1-1/4" CS 1-1/4" CS 2-3/8" API
Connection** Equivalent Equivalent Equivalent Equivalent Equivalent Hydril Reg.
Hydril Equivalent Equivalent
Make-up Torque 300-400 300-400 300-400 300-400 400-600 400-600 3700
(Ft-Lbs )
Minimum Up 2,500 2,500 2,000 2,500 3,000 4,000 5,000
Force (Lbs )
Maximum Up 4,000 4,000 4,500 5,500 8,000 16,000 34,000
Force (Lbs )
Minimum Down 2,000 2,000 2,000 2,000 2,500 3,000 5,000
Force (Lbs )
Maximum Down 4,000 4,000 4,000 4,000 8,000 12,000 20,000
Force (Lbs )

•The values contained herein are not to be construed as absolute. They are for
reference only

17
 MECHANICAL UP & DOWN INTENSIFIER

The SICONSA Mechanical Up & Down ntensifier

provides both upward and downward jar intensification.
In addition, the intensifier works to protect the pipe
from shock load. Particularly valuable at shallow depths,
the intensifier provides stroke that is not available in the pipe.
The stroke of the intensifier compliments the jar stroke and
self adjusts to the various release settings of the jar.

DESIGN FEATURES
•Fully Mechanical
•Not Affected by Temperature
•Not Affected by Pressure
•Up & Down Acceleration
•Sealed for Circulation
•Torque Transmitting
•Not dependent on Seals for Performance

UP & DOWN INTENSIFIER

Assembly Part UDACC-1-562-0 UDACC-1-660-0 LDUDACC-1- UDACC-1-812-0 UDACC-2-250-0 UDACC-2-700-0 UDACC-3-125-0
Number 812-0

Nominal O.D. 1.562 1.660 1.812 1.812 2.250 2.700 3.125

Minimum I.D. 0.250 0.250 0.562 0.250 0.312 0.562 1.000
Overall Length 6' 3-1/2" 6' 3-1/2" 6' 6-1/8" 6' 6-1/8" 7' 0" 6' 11-3/16" 11' 11-27/32"
(in.)
Makeup Length 6' 1-5/16" 6' 1-5/16" 6' 3-15/16" 6' 3-15/16" 6' 9-13/16" 6' 9" 11' 8-27/32"
(in.)
Weight 35 36 42 42 68 100 122
(Lbs .)
Torque Capacity 400 Ft-Lbs 400 Ft-Lbs 400 Ft-Lbs 400 Ft-Lbs 1,100 Ft-Lbs 1,900 Ft-Lbs 6,500 Ft-Lbs
Maximum Work 40,000 40,000 42,500 45,000 105,000 130,000 200,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS 1-1/4" CS 1-1/4" CS 1-1/4" CS Hydril 1-1/4" CS Hydril 2-3/8" API
Connection** Equivalent Hydril Hydril Hydril Equivalent Equivalent Reg.
Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600 400-600 400-600 3700
(Ft-Lbs )

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

18
The SICONSA Mechanical Wireline Jar releases to create an upward impact when the
applied line overpull equals the pre-load adjustment of the jar setting. When returned to
neutral and slacked off upon, the jar will automatically recock.

DESIGN FEATURES
•Fully Mechanical
•Not Affected by Temperature
•Not Affected by Pressure
•Easy Recock
•Not Dependent on Seals for Performance

There is no delay for release or recock. Once the

pre-load adjustment is exceeded, the release is
immediate.

Jar adjustment is performed by

removing the top bushing and
inserting the adjustment wrench.

MECHANICAL WIRELINE JAR

Assembly Part Number JZ-1-562-0 JZ-1-812-0
Nominal O.D. 1.562 1.812
Overall Length - COCKED 3' 8" 3' 8-1/4"
Overall Length - CLOSED 3' 7-1/4" 3' 7-1/2"
Overall Length - OPEN 4' 2" 4' 2-1/4"
Weight (Lbs.) 18 25
Maximum Work Load (Yield) 16,500 16,500
Standard Connection** 5/8" SR 3/4" SR
Make-up Torque (Ft-Lbs)
Minimum Up Force (Lbs) 300 400
Maximum Up Force (Lbs) 1,000 1,600
•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

19
MECHANICAL WIRELINE INTENSIFIER
The SICONSA Mechanical Wireline Intensifier stores energy that is applied by line
tension.
Installed in the tool string above the jars and weight bar, the intensifier provides
protection from shock load. Adjustment to various jar settings is automatic as the
intensifier stores energy from the highest to the lowest jar setting.
Fully mechanical, the intensifier is not dependent upon seals for performance. Pressure
and temperature do not hinder the intensifier’s performance.

DESIGN FEATURES
•Fully Mechanical
•Not Affected by Temperature
•Not Affected by Pressure
•Self Adjusting
•Not Dependent on Seals for Performance

MECHANICAL WIRELINE INTENSIFIER

Assembly Part Number AZ-1-562-0 AZ-1-812-0
Nominal O.D. 1.562 1.812
Overall Length (in.) 3' 1-1/8" 3' 1-1/8"
Weight (Lbs.) 15 20
Torque Capacity NA NA
Maximum Work Load 16,500 16,500
(Yield)
Standard Connection** 5/8" SR 3/4" SR
Make-up Torque (Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

20
The SICONSA Ratchet Overshot is a Vertical Catch/Vertical Release external pulling
tool. Deployed in the release position, the overshot will automatically engage upon
contact with the fish. Applying approximately 250 lb. slack off weight will cause the
overshot to release from the fish. The activation from release to engage can be
repeated as many times as required. There are no shear pins, the ratchet mechanism
cycles the grapple between the release and engage position Grapples and Bowls are
easily changed to accommodate a variety of fish dimensions. Smaller diameter
overshots can be converted to utilize much larger diameter bowls and grapples.

DESIGN FEATURES
•Vertical Catch/Release
•Sealed for Circulation
•No Shear Pins
•Mechanically Operated

The Overshot can be fitted with a wide variety of Bowls, Grapples,

guides, and extensions to externally engage practically any type of
fish.

21
 RATCHET OVERSHOT
Assembly P art N umber RO - 1- 844- 0 RO - 2- 250- 0 RO - 2- 812- 0 RO - 3- 250- 0
Nominal O.D. 1.844 2.250 2.812 3.250
Minimum I.D. 0.187 0.312 0.750 0.875
Overall Length 2' 3- 1/2" 2' 4" 2' 9- 3/16" 3' 0- 1/8"
Makeup Length 2' 3- 1/2" 2' 4" 2' 9- 3/16" 3' 0- 1/8"
W eight (Lbs.) 14 20 27 35
Maximum Work Load (Yield) 44,000 72,000 80,000 105,000
Pressure Rating 5,000 P S I 5,000 P S I 5,000 P S I 5,000 P S I
Standard Tubing Connection** 1" C S Hydril 1- 1/4" C S Hydril 1- 1/4" C S Hydril 1- 1/4" C S
Equivalent Equivalent Equivalent Hydril
Equivalent
Make- up Torque 300- 400 400- 600 400- 600 400- 600
(F t- Lbs)
Catch Range - F N .625 - 1.375 1.000 - 1.750 1.375 - 1.750 1.375 - 2.312
Catch Range - F C .687 - 1.500 .750 - 1.937 .750 - 1.937 1.750 - 2.750
Catch Range - C T 3/4", 1", 1- 1/4' 1", 1- 1/4", 1- 1/2" 1- 1/4", 1- 1/2", 2" 1- 1/2" - 2- 3/8"
Converted to 2.250" 2.812" 3.062" 3.750"
Catch Range - F N .875 - 1.750 ----- ----- -----
Catch Range - F C .750 - 1.937 .750 - 1.937 1.000 - 2.375 2.000 - 3.250
Catch Range - C T 1", 1- 1/4", 1- 1/2" 1- 1/4", 1- 1/2", 2" 1" - 2.375" 1- 1/2" - 2- 7/8"
Converted to 2.844" 4.375"
Catch Range - F N ----- 1.375 - 2.312 ----- -----
Catch Range - C T ----- ----- ----- 1.500 - 3.500

•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

22
HYDRO MECHANICAL RATCHET OVERSHOT

The SICONSA Hydro Mechanical Ratchet Overshot will engage a fish mechanically and
release hydraulically. When in the released position, the Overshot can not be activated
by pump rate and will only activate when the fish neck is contacted. Whenin the engage
position, the Overshot will not release through contact with the fish and will only release
when pumped through at a sufficient rate.

DESIGN FEATURES
•Prevents Inadvertent Release from Fish Neck
•Repeatable Release & Engagement
•Permits Low Circulation Rate Without Releasing
•Adjustable Pump Rate for Release

23
 HYDRO MECHANICAL RATCHET OVERSHOT

Assembly Part HYDRO-1-844-0 HYDRO-2-250-0 HYDRO-2-812-0 HYDRO-3-250-0

Number
Nominal O.D. 1.844 2.250 2.812 3.250
Maximum Work 44,000 72,000 80,000 105,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600
(Ft-Lbs)
Catch Range - FN .625 - 1.375 1.000 - 1.750 1.375 - 1.750 1.375 - 2.312
Catch Range - FC .687 - 1.500 .750 - 1.937 .750 - 1.937 1.750 - 2.750
Catch Range - CT 3/4", 1", 1-1/4' 1", 1-1/4", 1-1/2" 1-1/4", 1-1/2", 1-1/2" - 2-3/8"
2"
Converted to 2.250" 2.812" 3.062" 3.750"
Catch Range - FN .875 - 1.750 ----- ----- -----
Catch Range - FC .750 - 1.937 .750 - 1.937 1.000 - 2.375 2.000 - 3.250
Catch Range - CT 1", 1-1/4", 1-1/2" 1", 1-1/4", 1-1/2" 1", 1-1/4", 1- 1-1/2" - 2-7/8"
1/2"
Converted to ----- 2.844" ----- 4.375"
Catch Range - FN ----- 1.375 - 2.312 ----- -----
Catch Range - CT ----- ----- ----- 1.500 - 3.500

•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

24
 RATCHET SPEAR

The SICONSA Ratchet Spear is a Vertical Catch/Vertical Release internal pulling tool.
Deployed in the release position, the spear will automatically engage upon contact with
the fish. Applying approximately 250 lb. slack off weight will cause the spear to release
from the fish. The activation from release to engage can be repeated as many times as
required. There are no shear pins, the ratchet mechanism cycles the slip between the
release and engage position. Slips and Nose Cones are easily changed to
accommodate a variety of fish dimensions. Smaller diameter spears can be converted
to utilize much larger diameter slips and nose cones.

DESIGN FEATURES
•Vertical Catch/Release
•Sealed for Circulation
•No Shear Pins
•Mechanically Operated

A wide variety of nose cones, slips, extensions, guides, and

adapters can be added to the standard spear

RATCHET SPEAR
Assembly Part Number RS-1-844-0 RS-2-250-0 RS-3-125-0
Nominal O.D. 1.844 2.250 3.125
Minimum I.D. 0.187 0.312 0.625
Overall Length 33.500 33.500 39.000
Makeup Length 33.500 33.500 39.000
Weight (Lbs.) 18 26 60
Maximum Work Load 37,000 47,000 55,000
(Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 400-600 400-600
Catch Range - Standard 1.062 - 1.625 1.375 - 1.750 2.312 -2.500
Catch Range - Option 1 0.86 .937 - 1.562 1.375 - 1.750
Catch Range - Option 2 .973 - 1.062 ----- 1.562 - 2.562
Catch Range - Option 3 1.062 - 1.625 ----- -----
Converted to 2.250" 2.812" 3.625"
Catch Rang 1.375 - 1.875 1.562 - 2.562 3.125

•The values contained herein are not to be construed as absolute.

They are for reference only.

•Other thread connections available upon request.

25
The SICONSA Hydro Mechanical GS Adapter can convert any standard GS pulling tool
to operate mechanically with hydraulic assist. When the adapter is attached to a
standard GS pulling tool, applying slack off weight and pumping through the tool will
lock the GS in the released position. Returning to neutral weight and allowing pressures
to stabilize will allow the tool to reengage the fish neck. A low rate of circulation will not
cause the tool to release.

DESIGN FEATURES
•Adapts to Standard Pulling Tools
•Repeatable Operation
•No Shear Pins
•Can be used as Running Tool

26
 HYDRO MECHANICAL GS ADAPTER

Assembly Part FRGS-1-687-0 FRGS-2-000-0 FRGS-2-500-0 FRGS-3-000-0 FRGS-4-000-0

Number
Nominal O.D. 2.000 2.000 2.500 3.000 4.000
Actual O.D. 1.687 1.812 2.160 2.720 3.620
Minimum I.D. *** *** *** *** ***
Overall Length 2' 3/4" 2' 3/4" 2' 3/4" 2' 3/4" 2' 3/4"
Makeup Length 2' 3/4" 2' 3/4" 2' 3/4" 2' 3/4" 2' 3/4"
Weight (Lbs.) 12 13 14 15 18
Maximum Work 49,000 49,000 52,000 60,000 60,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 300-400 400-600 400-600 400-600
(Ft-Lbs)
Standard Catch: 2" GS Equiv. 2" GS Equiv. 2 1/2" GS Equiv. 3" GS Equiv. 4" GS Equiv

27
 INDEXING TOOL
The SICONSA Hydro Mechanical J Adapter can convert any standard J series pulling
tool to operate mechanically with hydraulic assist. When the adapter is attached to a
standard J pulling tool, applying slack off weight and pumping through the tool will lock
the pulling tool in the released position.
Returning to neutral weight and allowing pressures to stabilize will allow the tool to
reengage the fish neck. A low rate of circulation will not cause the tool to release.
A lock out feature within the adapter secures the pulling tool core to prevent
coremovement before activation to the released position.

DESIGN FEATURES
•Adapts to Standard Pulling Tools
•Repeatable Operation
•No Shear Pins
•Can be used as Running Tool

HYDRO MECHANICAL” J” ADPATER

Assembly Part Number HJPT-2-000-0 HJPT-2-500-0 HJPT-3-000-0
Nominal O.D. 2.000 2.500 3.000
Actual O.D. 1.859 2.250 2.796
Overall Length 2' 5-3/4" 2' 5-3/4" 2' 5-3/4"
Makeup Length 2' 5-3/4" 2' 5-3/4" 2' 5-3/4"
Weight (Lbs.) 15 19 21
Standard Catch 1.375 F.N. 1.750 F.N. 2.312 F.N.
Maximum Work Load 32,600 37,700 42,000
(Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1 1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent
Make-up Torque 300-400 300-400 400-600
(Ft-Lbs)

28
The SICONSA Indexing Tool rotates bottom hole assemblies in 60º increments. Use the
indexing tool to by-pass ledges or obstructions, rotate fishing tools, or align BHA with
fish. The indexing tool is available with either mechanical or hydraulic activation.

The mechanical model rotates by applying slack off weight. Each time slack off weight is
applied partial rotation occurs. When relieved, the tool’s bottom sub completes the 60º
incremental rotation.

Hydraulic models rotate partially each time the pump rate is increased to exceed the
pre-set activation rate. When circulation is stopped, the 60º incremental rotation is
completed. Hydraulic models also rotate by applying and relieving slack off weight.

DESIGN FEATURES
•Mechanical or Hydraulic/Mechanical
•Large Bore ID (Mechanical Model)
•Rotation Concurrent with Weight
Application
•Heavy Duty Design for Installation in Fishing Strings

A mule shoe wash nozzle attached to the indexing tool

can help by-pass a liner top. A cut lip guide attached
to an overshot and installed below the indexing tool can
help align with a fish

INDEXING TOOL
Assembly Part Number IT-1-844-0 IT-2-125-0 IT-2-700-0
Nominal O.D. 1.844 2.250 2.750
Minimum I.D. 0.562 0.625 1.000
Overall Length (in.) 31.500 32.500 33.000
Makeup Length (in.) 29.312 30.312 30.812
Weight (Lbs.) 15 22 32
Minimum Torque 8 Ft- Lbs 9 Ft- Lbs 20 Ft- Lbs
@ Minimum Load of 350 Lbs 350 Lbs 500 Lbs
Maximum Work Load 35,000 44,000 77,500
(Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

29
The SICONSA in Line Filter can be installed in the BHA to prevent debris from plugging
tools. Tools dependent upon a small orifice or restricted ID are subject to plugging off,
the in line filter utilizes a wire wrapped screen to protect downhole tools from debris
accumulation.

DESIGN FEATURES
•Large Surface Area
•Stainless Steel Screen Filter

STAINLESS STEEL WIRE WRAPPED SCREEN

IN LINE FILTER

Assembly Part ILF-1-750-0 ILF-2-062-0 ILF-2-625-0 ILF-3-187-0

Number
Nominal O.D. 1.750 2.125 2.625 3.250
Minimum I.D. *** *** *** ***
Overall Length 24-7/8" 24-7/8" 25-3/4" 25-3/4"
Makeup Length 22-5/8" 22-5/8" 23-1/2" 23-1/2"
Weight (Lbs.) 8 10 15 22
Maximum Work 41,000 73,000 98,000 150,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

30
The SICONSA Circulating Junk Basket is designed to retrieve small debris and light
debris that cannot be removed using standard mechanical tools.

Circulation through the jet body creates a pressure differential between the ambient fluid
and the trap body chamber causing flow into the trap body. Debris is caught in the flow
path and circulated into the trap body.

Captured debris is retained by the flutter trap. The filter located below the jet body
prevents debris from reentering the circulation path.

DESIGN FEATURES
•Flutter Trap
•Extendable
•Stainless Steel Screen Filter

Stainless Steel Filters & Flutter Traps

Prevent debris form escaping the Junk Basket

31
 CIRCULATING JUNK BASKET
Assembly Part JB-1-750-0 JB-2-062-0 JB-2-625-0 JB-3-187-0
Number
Nominal O.D. 1.750 2.125 2.625 3.250
Minimum I.D. *** *** *** ***
Overall Length 3' 9-5/8" 3' 9-5/8" 3' 10-1/8" 4' 5-1/8"
Makeup Length 3' 9-5/8" 3' 9-5/8" 3' 10-1/8" 4' 5-1/8"
Weight (Lbs.) 19 23 28 35
Maximum Work 41,000 73,000 98,000 150,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

32
 DEPLOYMENT UNION

The SICONSA Deployment Union is designed to couple and uncouple BHA’s that can
not be rotated for threading on to the coiled tubing. Once attached, the clutch provides
torque transmission to the BHA. Lengthy tool strings can be lubricated below the
wellhead by wireline and then reattached to coiled tubing, eliminating the need for
excessive riser height

33
 DEPLOYMENT UNION

Assembly Part Number DPU-1-844-0 DPU-2-250-0

Nominal O.D. 1.844 2.250
Minimum I.D. 0.625 0.812
Overall Length (in.) 15.562 15.562
Makeup Length 13.375 13.375
Weight (Lbs.) 7 9
Maximum Work Load (Yield) 55,500 84,500
Pressure Rating: 5,000 PSI 5,000 PSI
Standard Tubing Connection** 1" CS Hydril 1-1/4" CS Hydril
Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 400-600

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

34
The SICONSA Swivel Joint is a lockable swivel that allows tool strings to be assembled
without having to rotate the tool sting components above the swivel joint. Once the
connections below the swivel joint have been tightened, keys are inserted into the
swivel joint and secured to provide torque transmission. Built in vertical slack helps to
locate a position of neutral tension. When locked and tightened, the built in vertical slack
is removed.

DESIGN FEATURES
•Torque Transmitting
•Lockable Swivel
•Sealed for Circulation
•Vertical Slack

LOCKABLE SWIVEL JOINT

ASSEMBLY PART NO. SJT-1-687-00 SJT-2-250-

NOMINAL OD (in) 1.687 2.250
ACTUAL OD (in) 1.687 2.250
MINIMUM ID (in) 0.375 0.625
OVERALL LENGTH (in) 16.20 17.70
MAKE UP LENGTH (in) 14.02 15.51
WEIGHT (lb)
MAXIMUM WORK LOAD 32,007 53,151
(yield lb)
PRESSURE RATING (psi) 12,214 22,969
TORQUE CAPACITY (ft-lb) 364 802
STANDARD CONNECTION 1" CSH EQUIV. 1 1/4" CSH
MAKE UP TORQUE (ft-lb) 400 600

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

35
The SICONSA Tubing End Locator provides a reliable surface indication of production
string restrictions and the tubing end for depth correlation. Within the production tubing,
drag will be approximately 1000 to 1200 lb. When a normal nipple restriction is reached
drag will increase approximately 400 lb. When the end of the production tubing is
reached all drag produced by the tubing end locator will be lost. The process of locating
restrictions can be repeated as many times as desired.

DESIGN FEATURES
•Repeatable Surface Indications
•Can be used as Centralizer
•Can be used as Friction Tool
•Locates Landing Nipples & Tubing End

TUBING END LOCATOR

Assembly Part TEL-2-375-0 TEL-2-875-0 TEL-3-500-0 TEL-4-500-0
Number
Tubing Size 2-3/8" 2-7/8" 3-1/2' 4-1/2"
Nominal 1.750 2.125 2.500 3.250
O.D. - Mandrel
O.D. - Centralizer 1.995 2.312 2.995 3.813
Spg - Nipple:***
O.D. - Centralizer 2.125 2.562 3.125 4.125
Spg - End:***
Minimum I.D. 0.750 0.812 1.000 1.000
Drag in Tubing (Lbs) 1,000/1,200 1,000/1,200 1,600/1,800 1,600/1,800
Overall Length (in.) 2' 8-1/2" 2' 10-1/2" 3' 0" 3' 5-5/16"
Makeup Length (in.) 2' 6-5/16" 2' 8-5/16" 2' 9-13/16" 3' 3-1/8"
Weight (Lbs.) 16 29 40 67
Maximum Work 44,000 100,000 130,000 195,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

36
The SICONSA Tubing Cleaner removes barium, scale, cement, paraffin, and most other
build up from the production tubing wall. The spring loaded pivotal blades allow the
tubing cleaner to pass through normal tubing restrictions and clean out to the full tubing
ID. Blades are specially designed to pass through the minimum restriction and expand
to the tubing drift diameter. Either rotated from surface or below a motor, the tubing
cleaner blades have sufficient spring loading for maximum cleaning efficiency.

DESIGN FEATURES
•Blade Cleaning Ports
•Pivotal Carbide Blades

Carbide dressed blades are designed for each job. The

blade are then gauged for the minimum restriction and
drift diameter.

TUBING CLEANER
Assembly Part Number TC L- 1- 650- 0 TC L- 2 - 250- 0 TC L- 3 - 250- 0
No mina l O .D . 1.650 2.250 3.250
Minimum I.D . 0.250 0.375 0.625
Tubing Size 2- 3/8 " 3- 1/2 " 4- 1/2 "
Minimum Blade O .D . 1.650 2.412 3.437
Maximum Blade O .D . 2.000 3.000 4.000
Tubing Size 2- 7/8 " 4" 5"
Minimum Blade O .D . 2.150 2.912 3.937
Maximum Blade O .D . 2.500 3.500 4.500
Overall Length (in.) 1' 1- 5/8 " 1' 6- 7/1 6 " 1 ' 10- 15 /16"
M a k e up Length (in.) 11- 7/16" 1' 4- 1/4 ' 1' 8- 3/4 "
Weight (Lbs.) 7 17 35
Torque Capacity 550 F t- Lb s 2,750 F t- Lbs 5,000 F t- Lbs
Maximum Work Load (Yield ) 44,00 0 130,0 00 195,0 00
Pressure Ra ting 5,000 P S I 5 ,000 P S I 5 ,000 P S I
Standard Tubing Connection** 1" C S Hydril 1- 1/4 " C S Hydril 1- 1/4 " C S Hydril
Equivalent Equivalent Equivalent
Make - up Torque (Ft- Lbs) 300- 4 0 0 400- 6 0 0 400- 6 0 0
•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

37
DUAL CIRCULATING VALVE
The SICONSA Dual Circulating Valve provides a means of emergency circulation
through rupture discs and a ball operated circulating feature. The rupture discs provide
a means of circulating if the BHA become plugged. Applied internal pressure exceeding
the burst rating of the disc will cause the discs to rupture and open circulation to the
annular area. The ball operated valve shifts open when a ball is dropped to the tool and
pressure is applied to exceed the pre determined shear value of the valve. Once shifted,
circulation is diverted to the annular area. When not required, the rupture discs can be
removed and replaced with plugs

DESIGN FEATURES
•Adjustable Jet Pattern
•Heat Treated Nozzle Cone
•Easy Adjustment

DUAL CIRCULATING VALVE

Assembly Part Number DCV-1-687-0 DCV-2-125-0

Nominal O.D. 1.687 2.125
Minimum I.D.: 0.437 0.562
Overall Length (in.) 10.937 11.950
Makeup Length (in.) 8.750 9.750
Weight (Lbs.) 4 6
Maximum Work Load (Yield) 37,500 63,400
Pressure Rating 10,000 PSI 10,000 PSI
Temperature Rating (Deg. F) -20 / +250 -20 / +250
Standard Tubing Connection** 1" CS Hydril 1-1/4" CS Hydril
Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 400-600

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

38
 The SICONSA Tool String Centralizer features changeable
centralizer sleeves for added versatility.
The 5 bladed sleeves can be removed and changed to suit the
required centralizer diameter.
Threaded onto the main mandrel, the sleeves are non-rotating.

DESIGN FEATURES
•Non Rotating Sleeves
•Rugged 5 bladed Sleeves
•Changeable Sleeve Diameters

TOOL STRING CENTRALIZER

Body O.D. 1.750 2.125 2.500 2.875 3.250
O.D. Range 2.125 to 3.125 2.500 to 3.500 2.875 to 3.875 3.250 to 4.625 3.625 to 5.000
Minimum I.D. 0.750 1.000 1.000 1.375 1.750
Overall Length (in.) 13.688 13.000 13.437 13.500 13.500
Makeup Length (in.) 11.500 10.812 13.937 11.312 11.312
Weight (Lbs.) 7 to 8 9 to 11 14 to 16 17 to 21 19 to 22
Torque Capacity 1500 ft-lb 3500 ft-lb 5000 ft-lb 7000 ft-lb 10000 ft-lb
Maximum Work 65,000 93,000 140,000 160,000 190,000
Load (Yield)
Pressure Rating 10,000 PSI 10,000 PSI 10,000 PSI 10,000 PSI 10,000 PSI
Standard Tubing 1" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril 1-1/4" CS Hydril
Connection** Equivalent Equivalent Equivalent Equivalent Equivalent
Make-up Torque 300-400 400-600 400-600 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.
•Other thread connections available upon request.

39
TMX HYDRAULIC RUNNING TOOL
The SICONSA TMX Hydraulic Running Tool is designed to deploy X & R type lock
mandrels on coiled tubing. Fully hydraulic, the TMX is capable of landing nipple
selection, landing nipple location, lock mandrel closure, and separation ( pin shear)
between the lock mandrel and running tool.

Lock mandrels can be attached to the TMX in either the selective or locate position. A
low rate of circulation can be maintained while running in the well. An increased
circulation rate exceeding the pre determined setting will activate the tool through the
setting cycles. See next page for further details.

DESIGN FEATURES
•Fully Hydraulic
•Open Bore
•Not Dependent on Ball Drop
•No Jar Action Required
•Positive Lock Out between Stages

40
 TMX HYDRAULIC RUNNING TOOL

SEQUENCE OF OPERATION

When an X or R landing nipple is to be located below another landing nipple of the

same size, the Lock Mandrel is attached in the selective position. The lock mandrel and
running tool are deployed to a depth just above the desired landing nipple.

Pump rate is increased to the level set to activate the running tool. The running tool
shifts the lock mandrel to the locate position. When the first landing nipple or no-go
nipple are to be located, the lock mandrel/running tool may be run in this locate position.

Circulation is stopped and adequate time allowed for stabilization. The lock mandrel is
then lowered to the landing nipple and slack off weight applied.

While maintaining slack off weight, the pump rate is again increased to the level set to
activate the running tool. The running tool fully closes the lock mandrel to the set
position.

An upward strain provides a positive indication the lock mandrel has been fully set.
While maintaining upward strain and in creasing pump rate, the running tool will
separate from the lock mandrel.

41
The SICONSA Tubing Lock is used to anchor tools that require no vertical movement
during operation. A typical application is to install the tubing lock above a downhole
motor and anchor the BHA while operating a tubing cutter. The tubing lock activates
when pumped through and engages the tubing wall while pumping. Slack off weight
maintains the set position.

DESIGN FEATURES
•Interchangeable Slips for Various ID’s
•Low Pump Rate Activation
•Sealed for Circulation

TUBING LOCK
Assembly Part Number TL-1-650-0 TL-2-062-0
Nominal O.D. 1.650 2.062
Minimum I.D. 0.312 0.437
Tubing Size 2-3/8" & 2-7/8" 2-7/8" & 3-1/2"
Overall Length (in.) 2' 3-7/16" 2' 3-7/16"
Makeup Length (in.) 2' 1-1/4" 2' 1-1/4"
Weight (Lbs.) 11 15
Engaging Pressure 600 PSI 600 PSI
Maximum Work Load (Yield) 26,000 60,000
Pressure Rating 5,000 PSI 5,000 PSI
Standard Tubing Connection ** 1" CS Hydril 1-1/4" CS Hydril
Equivalent Equivalent
Make-up Torque (Ft-Lbs) 300-400 400-600

•The values contained herein are not to be construed as absolute.

They are for reference only.

•Other thread connections available upon request.

42
The SICONSA Tubing Cutter utilizes carbide tipped knives to cut through the tubing
wall. When pumped through, a hydraulic piston activates the blades. Rotation, while
pumping, provides the cutting action. When run below a downhole motor, a tubing lock
should be installed above the motor.

DESIGN FEATURES
•Adjustable Blade Deflection
•Carbide Knives
•Wide Range of Cut
•Long Lasting Knives

TUBING CUTTER
Assembly Part TC-1-625-0 TC-1-700-0 TC-1-750-0 TC-2-187-0 TC-2-500-0
Number
Nominal O.D. 1.625 1.700 1.750 2.187 2.500
Minimum I.D. 0.250 0.250 0.250 0.250 0.250
Tubing Size 2 3/8 2 3/8 to 2 7/8 2 3/8 to 2 7/8 2 7/8 to 4 1/2 4 1/2 to 5 1/2
Overall Length 1' 5-3/8" 1' 5-3/8" 1' 5-3/8" 1' 4" 1' 4"
(in.)
Makeup Length 1' 5-3/8" 1' 5-3/8" 1' 5-3/8" 1' 4" 1' 4"
(in.)
Weight (Lbs.) 8 8 9 13 15
Maximum Work 51,000 51,000 51,000 53,000 53,000
Load (Yield)
Pressure Rating 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI 5,000 PSI
Standard Tubing 1" CS Hydril 1" CS Hydril 1" CS Hydril 1-1/4" CS 1-1/4" CS
Connection ** Equivalent Equivalent Equivalent Hydril Hydril
Equivalent Equivalent
Make-up Torque 300-400 300-400 300-400 400-600 400-600
(Ft-Lbs)

•The values contained herein are not to be construed as absolute. They are for
reference only.

•Other thread connections available upon request.

43
 IMPRESSION BLOCK
The SICONSA Impression Block is specially designed for coiled tubing. Through porting
allows washing action to the impression target. A steel sleeve protects the lead from
washing out while circulating and side porting permits higher circulation rates.

DESIGN FEATURES
•Through Ported
•Steel Sleeved
•Heavy Duty
•Easy Redress

44
 WIRE RETRIEVING TOOLS

SICONSA Wire Retrieving Tools are ported for circulation and designed for use with
coiled tubing. A variety of styles are available for various fishing operations. The wire
finder mandrel and skirt is an all in one tool, which helps to prevent wire by-pass.

DESIGN FEATURES
•Heavy Duty Construction
•Ported for Circulation

45
SICONSA stocks a variety of nozzle shapes and sizes. Multi ported, side wash, down
wash, and mule shoe nozzles are just a few of the different types available. Specially
designed nozzles to suit any application can be fabricated as requested The SICONSA
indexing tool is ideal for use with our wash nozzles. Jet washing, spotting fluids, and
cleaning operations are sometimes difficult because of ledges and other obstructions. A
wash nozzle installed below the indexing tool can help to rotate the BHA past various
obstructions

46
WASH NOZZLES
A large assortment of cross overs commonly used by the coiled tubing industry are
inspected and awaiting call out. Ported subs, centralizers, wash nozzles, spacers,
deployment bars, and fluted guides are stocked for rental jobs.

SPECIAL TOOLS

Special fishing tools are always ready when the need arises. Wire retrieving tools,
scratchers, special pulling tools, magnets, cut lip guides, and split skirts are just some of
the tools ready to be utilized.

47
SICONSA stocks a full line of accessory tools such as; Blind Boxes, Mils, Reamers,
Guides, Broaches, ported subs, and much more.

At SICONSA we provide services to enhance our product performance. We are

prepared to offer advice and get involved during pre job planning. Training, technical
support, and assistance are available 24 hours per day.

Tool String Schematics for recommended tool string configurations are available and
can be an invaluable asset during the job planning stages.

48
ITEM TOOL STRING SCHEMATIC

CUSTOMER: JOHN DOE C.T. O.D.: 1.500 PREPARED BY: TAYLOR

MADE
COMPANY: XYZ OIL C.T. WALL: 0.134
WELL: TMOT II C.T. I.D.: 1.232 SAMPLE
DATE: 1/1/01 TBG SIZE: 3 1/2" SCHEMATIC

REF. DESCRIPTION S.N. O.D I.D. M.U. LENGTH MAX WORK LOAD
1 EXTERNAL 100 1.800 0.750 10.125 60,500
CONNECTOR
2 DUAL FLAPPER 101 1.750 0.625 15.375 70,000
VALVE

3 INTERNAL HYD. 102 1.800 0.437 12.688 39,500

DISCONNECT
4 UP & DOWN 103 1.812 0.250 75.937 45,000
ACCELERATOR
5 UP & DOWN JAR 104 1.812 0.250 94.062 45,000
6 HYDRAULIC 105 1.812 24.750 49,000
INTERNAL PULLING
TOOL

TOOL STRING MAXIMUM O.D.:

1.812

TOOL STRING MINIMUM I.D.:

0.250

TOOL STRING MAXIMUM WORK LOAD: 39,500

TOOL STRING MAKE UP LENGTH: INCHES 232.937 FEET 19.411

49
PRESSURE CONTROL VALVE

The SICONSA Pressure Control Valve is designed to support a column of fluid above
the valve. An increase in pressure exceeding the selected valve setting will open the
valve and allow flow through the valve. Once the pressure has been reduced to the
selected valve setting, the valve will close and again shut off flow through the valve.

Adjustment to the valve opening setting is achieved by installing a seal on the

designated piston groove. The varied piston diameters provide for a selection of cross
sectional areas to alter the operating pressure of the valve.

When sufficient pressure is applied to the valve, the piston moves upward and pulls the
ball off seat. Flow is routed through ports in the piston and through slots in the ball cage.

50
 PRESSURE CONTROL VALVE
OPENING PRESSURE CHART

STANDARD STANDARD STANDARD

STACK WITH WASHER #1 STACK WITH WASHER #2 STACK WITH WASHER #3
(.125) (.250) (.375)
SEAL @ POS. 1 570 PSI 1260 PSI 2320 PSI
SEAL @ POS. 2 880 PSI 1970 PSI 3620 PSI
SEAL @ POS. 3 1660 PSI 3720 PSI DO NOT USE

USE POSITION 4 FOR HIGH PRESSURE APPLICATIONS ONLY!!!

HIGH PRESSURE HIGH PRESSURE HIGH PRESSURE

STACK WITH NO STACK WITH WASHER #1 STACK WITH WASHER
WASHER (.125) #2 (.250)
SEAL @ POS. 4 2430 PSI 3990 PSI 5200 PSI

INSTALL PISTON SEAL AT DESIRED POSITION ONLY. ALL OTHER SEALS MUST BE
REMOVED FROM PISTON THIS CHART IS INTENDED FOR REFERENCE ONLY.

VARIATIONS TO THE BELLEVILLE WASHER LOADS MAY OCCUR AFTER USAGE. A

PRESSURE TEST SHOULD BE PERFORMED TO VERIFY THE SELECTED
SETTING.

51
52
 3.125” PRESSURE CONTROL VALVE OPENING PRESSURE CHART

STACK #1 (9 SETS 2 FACING 2-B2250-073)

WASHER #3 (.595) WASHER #4 (.625) WASHER #5 (.750)
SEAL @ POS. 1 375 500 600
SEAL @ POS. 2 1100 1375 1750
SEAL @ POS. 3 2250 2750 3500
STACK #2 (10 SETS 2 FACING 2-B2250-073)
WASHER #1 (.325) WASHER #2 (.375) WASHER #3 (.595) WASHER #4 (.625) WASHER #5 (.750)
SEAL @ POS. 1 650 750 850 900 1000
SEAL @ POS. 2 1800 2000 2250 2500 2750
SEAL @ POS. 3 3750 4250 4750 5000 5500

THICKNESS

THIS CHART IS INTENDED FOR REFERENCE ONLY. VARIATIONS TO THE

BELLEVILLE WASHER LOADS MAY OCCUR AFTER USAGE. A PRESSURE TEST
SHOULD BE PERFORMED TO VERIFY THE SELECTED PRESSURE SETTING.

53
INSTALL SEAL AT DESIRED POSITION ONLY. ALL OTHER SEALS MUST BE
REMOVED FROM PISTON.

PRESSURE CONTROL VALVE

ASSEMBLY PART NO. DCV-2-125-00 DCV-3-125-00
NOMINAL OD (in) 2.125 3.125
ACTUAL OD (in) 21.250 3.125
MINIMUM ID (in) 0.375 0.688
OVERALL LENGTH (in) 20.29 26.46
MAKE UP LENGTH (in) 18.10 24.28
WEIGHT (lb)
MAXIMUM WORK LOAD 72,177 121,584
(yield lb)
PRESSURE RATING (psi) 10,126 6,959
TORQUE CAPACITY (ft-lb) 1,621 4,806
TEMPERATURE RATING -20/+550 -20/+550
(deg. F)
STANDARD CONNECTION 1 1/4" CSH EQUIV. 2 7/8" PAC
MAKE UP TORQUE (ft-lb) 400 2,900

The values contained herein are not to be construed as absolute.

They are intended for use as a reference only.

54