Scribd
Upload
927 views2 pages

Codigo de Cronometro VHDL

This document describes a cronometer entity with a behavioral architecture. It contains signals that count seconds, tenths of seconds, and hundredths of seconds. On each clock cycle, it increments the appropriate counter and displays the current time on a 7-segment display. It uses a 3-bit counter to cycle through the four anodes and display the corresponding time value.

Uploaded by

Estick Mauricio Palomino Puerto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
927 views2 pages

Codigo de Cronometro VHDL

This document describes a cronometer entity with a behavioral architecture. It contains signals that count seconds, tenths of seconds, and hundredths of seconds. On each clock cycle, it increments the appropriate counter and displays the current time on a 7-segment display. It uses a 3-bit counter to cycle through the four anodes and display the corresponding time value.

Uploaded by

Estick Mauricio Palomino Puerto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

ibrary IEEE;

use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;

entity cronometro is
Port ( display : out STD_LOGIC_VECTOR (7 downto 0);
clk, reset, enc : in STD_LOGIC;
An : out STD_LOGIC_VECTOR (3 downto 0));
end cronometro;

architecture Behavioral of cronometro is


signal contador: std_logic_vector (3 downto 0) :="0000";
signal segundos: std_logic_vector (13 downto 0) :="00000000000000";
signal contador1: std_logic_vector (3 downto 0) :="0000";
signal DecSeg: std_logic_vector (9 downto 0) :="0000000000";
signal contador2: std_logic_vector (3 downto 0) :="0000";
signal CentSeg: std_logic_vector (7 downto 0) :="00000000";
signal Anodos: std_logic_vector (1 downto 0 ):="00";

begin
Process (clk, reset, contador, segundos)
begin
if (clk'event and clk = '1') then
if reset= '0' then
contador <="0000";
segundos <="00000000000000";
contador1 <="0000";
DecSeg <="0000000000";
else
Anodos <= Anodos + 1 ;
if Anodos="11" then
Anodos<= "00";
end if;
case Anodos is
when "00"=> if segundos = "10011100010000" then
contador <= contador + 1 ;
segundos <= "00000000000000";
if contador = "1001" then
contador <= "0000";
end if;
else
segundos <= segundos + 1;
end if;
An <= "1011";
case contador is
when "0000" => display <= "00000010";
when "0001" => display <= "10011110";
when "0010" => display <= "00100100";
when "0011" => display <= "00001100";
when "0100" => display <= "10011000";
when "0101" => display <= "01001000";
when "0110" => display <= "01000000";
when "0111" => display <= "00011110";
when "1000" => display <= "00000000";
when others => display <= "00011000";
end case;
when "01"=> if CentSeg = "00111000" then
contador2 <= contador2 + 1 ;
CentSeg <= "00000000";
if contador2 = "1001" then
contador2 <= "0000";
end if;
else
CentSeg <= CentSeg + 1;
end if;
An <= "1110";
case contador2 is
when "0000" => display <= "00000010";
when "0001" => display <= "10011110";
when "0010" => display <= "00100100";
when "0011" => display <= "00001100";
when "0100" => display <= "10011000";
when "0101" => display <= "01001000";
when "0110" => display <= "01000000";
when "0111" => display <= "00011110";
when "1000" => display <= "00000000";
when others => display <= "00011000";
end case;
when others=> if DecSeg = "1111101000" then
contador1 <= contador1 + 1 ;
DecSeg <= "0000000000";
if contador1 = "1001" then
contador1 <= "0000";
end if;
else
DecSeg <= DecSeg + 1;
end if;
An <= "1101";
case contador1 is
when "0000" => display <= "00000010";
when "0001" => display <= "10011110";
when "0010" => display <= "00100100";
when "0011" => display <= "00001100";
when "0100" => display <= "10011000";
when "0101" => display <= "01001000";
when "0110" => display <= "01000000";
when "0111" => display <= "00011110";
when "1000" => display <= "00000000";
when others => display <= "00011000";
end case;
end case;
end if;
end if;
end process;
end Behavioral;

You might also like