APL5155

High Input Voltage, Low Quiescent Current, 150mA LDO Regulator

Features General Description

• Wide Input Voltage Range: 5.4V to 25V The APL5155 is a low ground current linear regulator,
• Ultra Low Ground Current: 10µA which operates with input voltage from 5.4V to 25V and
• High Output Accuracy: ±2.5% delivers output current up to 150mA. Typical dropout volt-
• Excellent Load/Line Transient age is only 750mV at 150mA loading. This combination
of the high voltage and the low ground current makes the
• Low Dropout Voltage: 750mV @ 150mA
APL5155 ideal for USB and portable devices, using 2-
• Fixed Output Voltages for 5V/3.3V or Adjustable
cell or 3-cell Li-Ion battery inputs.
Voltage
The APL5155 is stable with aluminum, tantalum, and
• Built-In Current-Limit Protection
ceramic capacitors. It requires a 1µF or greater capacitor
• Built-In Over-Temperature Protection for stability.
• Zero Shutdown Current The APL5155 has many protection functions, including
• Internal Soft-Start Function over-temperature, current-limit and short circuit current
• POR Scheme to Prevent VOUT Spike limit protections, which prevent the device from thermal
• SOT-23-5, SOT-89, and SOP-8P Packages over-load and current over-load.
• Lead Free and Green Devices Available The APL5155 regulator is available in miniature SOT-23-
5, SOT-89, and SOP-8P packages.
(RoHS Compliant)

Applications Pin Configuration

VIN 1 5 VOUT
• USB Power Supply GND 2
• Keep-Alive Supply in Notebook and Portable EN 3 4 NC/ADJ
Computers
SOT-23-5
• Logic Supply for High-Voltage Batteries
(Top View)
• Battery Powered Systems
GND 1

VIN 2 TAB : VIN

VOUT 3

SOT-89
(Top View)

VOUT 1 8 VIN
NC 2 7 GND
NC 3 6 NC
NC/ADJ 4 5 EN
SOP-8P
(Top View)
= Thermal Pad
(connected to GND plane for better heat dissipation)

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.

Copyright  ANPEC Electronics Corp. 1 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Ordering and Marking Information

APL5155 Package Code
B : SOT-23-5 D : SOT-89 KA : SOP-8P
Operating Ambient Temperature Range
Assembly Material I : -40 to 85 oC
Handling Code Handling Code
TR : Tape & Reel
Temperature Range Voltage Code
Package Code 33 : 3.3V 50 : 5.0V Blank : Adjustable Version
Assembly Material
Voltage Code G : Halogen and Lead Free Device

APL5155 B : L55X X - Date Code

APL5155 33B : 55RX X - Date Code ; R - 3.3V

APL5155 50B : 55ZX X - Date Code ; Z - 5.0V

APL5155 D : APL5155 XXXXX - Date Code

XXXXX

APL5155
APL5155 KA : XXXXX XXXXX - Date Code

Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).

Absolute Maximum Ratings (Note 1)

Symbol Parameter Rating Unit

VIN, VEN VIN, EN to GND Voltage - 0.3 to 27 V
VOUT, VADJ VOUT, ADJ to GND Voltage - 0.3 to 27 V
o
TJ Maximum Junction Temperature 150 C
o
TSTG Storage Temperature -65 to 150 C
o
TSDR Maximum Lead Soldering Temperature, 10 Seconds 260 C
Note1: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are
stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recom-
mended operating conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device
reliability.

Thermal Characteristics
Symbol Parameter Typical Value Unit
Thermal Resistance-Junction to Ambient (Note 2)
SOT-23-5 235
θJA
o
C/W
SOT-89 180
SOP-8P 50
Thermal Resistance-Junction to Ambient (Note 2)
SOT-23-5 130
θJC
o
C/W
SOT-89 38
SOP-8P 20
Note 2: θJA is measured with the component mounted on a high effective thermal conductivity test board in free air.

Copyright  ANPEC Electronics Corp. 2 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Recommended Operating Conditions (Note 3)

Symbol Parameter Range Unit
VIN VIN to GND Voltage 5.4 to 25 V
IOUT VOUT Source Current 0 to 150 mA
VOUT Adjustable Output Voltage 1.24 to 20 V
VEN EN Pin Input Voltage 0 to 25 V
COUT Output Capacitance 1 to 4.7 µF
ESR The ESR of Output Capacitance 5 to 50 mΩ
o
TA Ambient Temperature -40 to 85 C
o
TJ Junction Temperature -40 to 125 C

Note 3: Refer to the typical application circuit.

Electrical Characteristics
Unless otherwise noted, these specifications apply over VIN=VOUT+3V, CIN=1µF, COUT=2.2µF, TA=-40 to 85oC.

APL5155
Symbol Parameter Test Conditions Unit
Min. Typ. Max.
POWER-ON-RESET (POR) AND SUPPLY CURRENT
VIN Input Voltage 5.4 - 25 V
Rising VIN POR Threshold 4.5 5 5.25 V
VIN POR Hysteresis - 200 - mV
IOUT=0mA, EN=high, Adj mode - 10 20
IQ Quiescent Current µA
IOUT=0mA, EN=high, Fix Mode - 15 25
IQSHDN Shutdown Supply Current EN=Low, VIN=19V - 1 3 µA
REFERENCE AND OUTPUT VOLTAGE
VREF Reference Voltage Adjustable Voltage Version - 1.24 - V
o
VREF Voltage Accuracy IOUT=10mA, TA=25 C -2.5 - 2.5 %
o
VREF Temperature Coefficient TJ=-40 to 125 C - 50 - ppm
Fixed Voltage Version - 3.3 -
VOUT Output Voltage V
Fixed Voltage Version - 5.0 -
Output Voltage Accuracy IOUT=10mA, TA=25oC -2.5 - 2.5 %
IOUT Load Current Range 0 - 150 mA
REGLINE Line Regulation VOUT+3V<VIN<25V, IOUT=1mA, VOUT=5V - 0.1 0.5 %
REGLOAD Load Regulation 0.1mA<IOUT<150mA, VOUT=5V - 0.6 1.4 %
IOUT=30mA, VOUT=20V - 160 240
IOUT=100mA, VOUT=20V - 500 750
VDROP Dropout Voltage mV
IOUT=150mA, VOUT=20V - 750 1125
IOUT=10mA, VOUT=5V - 150 225
PROTECTIONS
TOTP Over-Temperature Threshold TJ rising - 150 - °C
Over-Temperature Hysteresis - 30 - °C

Copyright  ANPEC Electronics Corp. 3 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Electrical Characteristics (Cont.)

Unless otherwise noted, these specifications apply over VIN=VOUT+3V, CIN=1µF, COUT=2.2µF, TA=-40 to 85oC.
APL5155
Symbol Parameter Test Conditions Unit
Min. Typ. Max.
PROTECTIONS (CONT.)
ILIMIT Current-Limit VIN=VOUT +3V, to 25V 200 - 400 mA
ISHORT Short-Circuit Current VOUT=0V, only for Fix mode - 50 - mA
SOFT-START AND SHUTDOWN
TSS Soft-Start Interval From VEN rising to VOUT=90% - 1 - ms
EN Input Logic HIGH IC is enabled 2.5 - - V
EN Input Logic LOW IC is shut down 0 - 0.6 V
EN Input Logic Hysteresis VOUT+3V<VIN<25V - 0.2 - V
IEN EN Pin Input Bias Current VEN=25V - 0.1 1 µA

Copyright  ANPEC Electronics Corp. 4 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Typical Operating Characteristics

Quiescent Current vs. Input Voltage Quiescent Current vs. Output Current
12 300
No Load VIN =12V
11 250
Quiescent Current (µA)

Quiescent Current (µA)

10 200

9 150

8 100

7 50

6 0
0 2 4 6 8 10 12 14 16 18 20 22 24 26 0 25 50 75 100 125 150
Input Votlage (V) Output Current (mA)

Quiescent Current vs. Junction Temperature Dropout Voltage vs. Output Current
14 1.0
VIN =8V, No Load VOUT=20V
0.9
12
0.8
Quiescent Current (µA)

Dropout Voltage (V)

10 0.7

8 0.6
0.5
6
0.4
4 0.3
0.2
2
0.1
0 0
-40 -20 0 20 40 60 80 100 120 0 25 50 75 100 125 150
Junction Temperature ( oC) Output Current (mA)

Reference Voltage vs. Junction Temperature PSRR vs. Frequency

1.260 0
VIN =8V VIN=12V, VIN=3.3V,
1.255 -10 CIN=1µF, COUT=2.2µF
-20
Reference Voltage (V)

1.250
-30
1.245
PSRR (dB)

-40
1.240 -50

1.235 -60
-70
1.230
-80
1.225
-90
1.220 -100
-40 -20 0 20 40 60 80 100 120 0.1 1 10 100 1000
o
Junction Temperature ( C) Frequency (kHz)

Copyright  ANPEC Electronics Corp. 5 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Operating Waveforms
The test condition is TA=25oC unless otherwise specified.

Turn On Response Turn Off Response

VE N VE N
1 1

VOUT

V OUT
2 2

VIN=12V, VOUT=3.3V, ROUT=33Ω, VIN=12V, VOUT=3.3V, ROUT=33Ω,

CIN=1µF/X7R, COUT=2.2µF/X7R CIN=1µF/X7R, COUT=2.2µF/X7R
CH1: VEN, 5V/Div, DC CH1: VEN, 5V/Div, DC
CH2: VOUT, 1V/Div, DC CH2: VOUT, 1V/Div, DC
TIME: 0.5ms/Div TIME: 0.2ms/Div

Power On Power Off

VIN

VIN

VOUT VOUT

1,2 1,2

VIN=12V, VOUT=3.3V, ROUT=33Ω, VIN=12V, VOUT=3.3V, ROUT=33Ω,

CIN=1µF/X7R, COUT=2.2µF/X7R CIN=1µF/X7R, COUT=2.2µF/X7R
CH1: VIN, 2V/Div, DC CH1: VIN, 2V/Div, DC
CH2: VOUT, 1V/Div, DC CH2: VOUT, 1V/Div, DC
TIME:5ms/Div TIME:5ms/Div

Copyright  ANPEC Electronics Corp. 6 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Operating Waveforms (Cont.)

The test condition is TA=25oC unless otherwise specified.

Load Transient Response Line Transient Response

VOUT
1
VIN
1

V OUT
2
IOUT
2

VIN=12V, VOUT=3.3V, CIN=1µF/X7R, VIN=11.5-12.5-11.5V, Falling/Rising=1µs,

COUT=2.2µF/X7R, IOUT=3-150-3mA, VOUT=3.3V, IOUT=10mA, CIN=1µF/X7R,
Falling/Rising Slew Rate=1A/µs COUT=2.2µF/X7R
CH1: VOUT, 100mV/Div, offset=3.3V CH1: VIN, 1V/Div, Offset=11.5V
CH2: IOUT, 100mA/Div, DC CH2: VOUT, 50mV/Div, Offset=3.3V
TIME: 50µs/Div TIME: 50µs/Div

Pin Description
PIN
NO. FUNCTION
NAME
SOT-23-5 SOT-89 SOP-8P
1 2 8 VIN Voltage Supply Input Pin.
2 1 7 GND Ground.
3 - 5 EN Enable Input Pin. Logic low=shutdown; logic high=enable.
NC: No Connection (fixed output voltage version).
4 - 4 NC/ADJ
ADJ: Output Voltage Feedback Pin (adjust output voltage version).
5 3 1 VOUT Regulator Output Pin.
- - 2, 3, 6 NC No Connection.

Copyright  ANPEC Electronics Corp. 7 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Block Diagram
1. Adjust Output Voltage (SOT-23-5/SOP-8P)

VIN

POR Current-
Limit

Control VREF
EN Logic 1.24V
Soft-
Start
VOUT
OTP
Short-Circuit
Current-Limit

GND ADJ

2. Fixed Output Voltage (SOT-23-5/SOP-8P)

VIN

POR Current-
Limit

Control VREF
EN Logic 1.24V
Soft-
Start
VOUT
OTP
Short-Circuit
Current-Limit

GND

Copyright  ANPEC Electronics Corp. 8 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Block Diagram (Cont.)

3. Fixed Output Voltage (SOT-89)

VIN

POR Current-
Limit

Control VREF
Logic 1.24V
Soft-
Start
VOUT
OTP
Short-Circuit
Current-Limit

GND

Copyright  ANPEC Electronics Corp. 9 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Typical Application Circuit

1. Adjust Output Voltage (SOT-23-5/SOP-8P)

VIN VOUT
VIN APL5155 VOUT
CIN B R1
APL5155 COUT
1µF EN KA ADJ 2.2µF
GND R2
ON
OFF

VOUT=1.24V x (R1+R2)/R2

2. Fixed Output Voltage (SOT-23-5/SOP-8P)

VIN VOUT
VIN VOUT
CIN COUT
1µF EN 2.2µF
GND
ON
OFF

3. Fixed Output Voltage (SOT-89)

VIN VOUT
VIN APL5155 VOUT
B
CIN COUT
APL5155
1µF KAGND 2.2µF

Copyright  ANPEC Electronics Corp. 10 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Application Information
Enable/Shutdown TJ − TA
PD(MAX ) =
θJA
The APL5155 features an active-high enable pin that al-
lows the regulator to be disabled. Forcing the enable pin where TJ-TA is the temperature difference between the
low disables the regulator, so current consumed by the junction and ambient air. θJA is the thermal resistance
regulator goes nearly to zero. Forcing the enable pin high between junction and ambient air.
enables the output voltage. The enable pin can not float. For continual operation, do not exceed the absolute maxi-
mum junction temperature rating of TJ=125oC.
Input Capacitor For example:
The APL5155 has high input voltage up to 25V. The input In SOT-23-5 package θJA=235oC/W. When operates the
capacitor must be rated to sustain voltages that may be APL5155 at TA=50 oC, the maximum power dissipation
used on the input. An input capacitor may be required can be determined as below:
when the device is not near the source power supply or PD(MAX)=(125oC-50oC)/(235oC/W)
when supplied by a battery. Small and surface-mounted PD(MAX)=319.1mW
ceramic capacitors can be used for bypassing. A larger
value may be required if the source supply has high ripple. Thermal Pad Consideration

Output Capacitor The SOP-8P is a cost-effective package which features a

small size, like a standard SOP-8, and a bottom thermal
The APL5155 requires an output capacitor for stability.
pad to minimize the thermal resistance of the package is
The design requires 1µF or greater on the output to main-
applicable to high current applications. The thermal pad
tain stability. It is optimized by using low-ESR ceramic
must be soldered down to the copper plane on circuit
chip capacitors. The maximum allowable ESR is 3Ω. More
board. Heat can be conducted away from the thermal
capacitance improves transient response. Place the out-
pad through the copper plane to ambient. If the copper
put capacitor as close to the VOUT pin as possible.
plane is not on the top surface of the circuit board, 4 or 6
X7R/X5R dielectric-type ceramic capacitors are recom-
vias should be used to thermally couple the thermal pad
mended because of their temperature performance. X7R
to the bottom plane.
type capacitors change capacitance by 15% over their
For good thermal conduction, the vias must be plated
operating temperature ranges. To use a ceramic chip
through and solder filled. The copper plane used to con-
capacitor with Y5V dielectric, the value must be much
duct heat away from the thermal pad should be as large
higher than an X7R ceramic capacitor to ensure the same
as practical.
minimum capacitance over the equivalent operating tem-
perature range. 0.072 0.118

No-Load Stability 0.024

The APL5155 will remain stable and in regulation with no

load unlike many other voltage regulators. This is espe-
cially important in CMOS RAM keep-alive applications. 0.150

Thermal Consideration ground

plane for
The thermal resistance of junction to ambient controls thermal
the APL5155's maximum power dissipation. The power pad
0.212
dissipation across the device is PD=IOUT (VIN-VOUT), and the SOP-8P Layout Recommendation
maximum power dissipation is:

Copyright  ANPEC Electronics Corp. 11 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Application Information (Cont.)

Adjustable Regulator Application SOP-8P

The output voltage of APL5155 can be adjusted from 3V 0.024

to 20V by using two external resistors. The resistors set
8 7 6 5

0.072
the output voltage based on the following equation:
 R 
VOUT = VREF 1 +  1 


  R2 
0.138

0.212
where VREF=1.24V

0.118
The resistors should be placed as close the device as
possible to avoid noise.

Recommended Minimum Footprint

1 2 3 4
SOT-23-5
0.076 0.050 Unit : Inch
0.1

0.05

0.038 0.02
Unit : Inch

SOT-89

0.076
0.140
0.104

0.067

0.059 0.022
Unit : Inch

Copyright  ANPEC Electronics Corp. 12 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Package Information
SOT-23-5

D
e

SEE
VIEW A

E1

E
b c
e1

0.25
A2

GAUGE PLANE
SEATING PLANE
A1

0
VIEW A

S SOT-23-5
Y
M MILLIMETERS INCHES
B
O
L MIN. MAX. MIN. MAX.
A 1.45 0.057
A1 0.00 0.15 0.000 0.006
A2 0.90 1.30 0.035 0.051
b 0.30 0.50 0.012 0.020
c 0.08 0.22 0.003 0.009
D 2.70 3.10 0.106 0.122
E 2.60 3.00 0.102 0.118
E1 1.40 1.80 0.055 0.071
e 0.95 BSC 0.037 BSC
e1 1.90 BSC 0.075 BSC
L 0.30 0.60 0.012 0.024
0 0° 8° 0° 8°
Note : 1. Follow JEDEC TO-178 AA.
2. Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.

Copyright  ANPEC Electronics Corp. 13 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Package Information
SOT-89
D A
D1 C

E1
E
H
L
e
e1

B1 B

S SOT-89
Y
M MILLIMETERS INCHES
B
O
L MIN. MAX. MIN. MAX.
A 1.40 1.60 0.055 0.063
B 0.44 0.56 0.017 0.022
B1 0.36 0.48 0.014 0.019
C 0.35 0.44 0.014 0.017
D 4.40 4.60 0.173 0.181
D1 1.62 1.83 0.064 0.072
E 2.29 2.60 0.090 0.102
E1 2.13 2.29 0.084 0.090
e 1.50 BSC 0.059 BSC
e1 3.00 BSC 0.118 BSC
H 3.94 4.25 0.155 0.167
L 0.89 1.20 0.035 0.047

Note : Follow JEDEC TO-243 AA.

Copyright  ANPEC Electronics Corp. 14 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Package Information
SOP-8P
-T- SEATING PLANE < 4 mils

SEE VIEW A

D1
E2
THERMAL
E1

E
PAD

h X 45o
e b c
A2

0.25
A1

GAUGE PLANE
SEATING PLANE
L θ

VIEW A

S SOP-8P
Y
M MILLIMETERS INCHES
B
O
L MIN. MAX. MIN. MAX.
A 1.60 0.063
A1 0.00 0.15 0.000 0.006
A2 1.25 0.049
b 0.31 0.51 0.012 0.020
c 0.17 0.25 0.007 0.010
D 4.80 5.00 0.189 0.197
D1 2.50 3.50 0.098 0.138
E 5.80 6.20 0.228 0.244
E1 3.80 4.00 0.150 0.157
E2 2.00 3.00 0.079 0.118
e 1.27 BSC 0.050 BSC
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
θ 0oC 8o C 0o C 8o C

Note : 1. Followed from JEDEC MS-012 BA.

2. Dimension "D" does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion or gate burrs shall not exceed 6 mil per side .
3. Dimension "E" does not include inter-lead flash or protrusions.
Inter-lead flash and protrusions shall not exceed 10 mil per side.

Copyright  ANPEC Electronics Corp. 15 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Carrier Tape & Reel Dimensions

OD0 P0 P2 P1 A

E1
F

W
B0

K0 A0 A
B OD1 B

SECTION A-A

T
SECTION B-B

d
H
A

T1

Application A H T1 C d D W E1 F
8.4+2.00 13.0+0.50
178.0±2.00 50 MIN. 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05
-0.00 -0.20
SOT-23-5 P0 P1 P2 D0 D1 T A0 B0 K0
1.5+0.10 0.6+0.00
4.0±0.10 4.0±0.10 2.0±0.05 1.0 MIN. 3.20±0.20 3.10±0.20 1.50±0.20
-0.00 -0.40
Application A H T1 C d D W E1 F
12.4+2.00 13.0+0.50
178.0±2.00 50 MIN. 1.5 MIN. 20.2 MIN. 12.0±0.30 1.75±0.10 5.50±0.05
-0.00 -0.20
SOT-89 P0 P1 P2 D0 D1 T A0 B0 K0
1.5+0.10 0.6+0.00
4.0±0.10 8.0±0.10 2.0±0.05 1.5 MIN. 4.80±0.20 4.50±0.20 1.80±0.20
-0.00 -0.40
Application A H T1 C d D W E1 F
12.4+2.00 13.0+0.50
330.0±2.00 50 MIN. 1.5 MIN. 20.2 MIN. 12.0±0.30 1.75±0.10 5.5±0.05
-0.00 -0.20
SOP-8P P0 P1 P2 D0 D1 T A0 B0 K0
1.5+0.10 0.6+0.00
4.0±0.10 8.0±0.10 2.0±0.05 1.5 MIN. 6.40±0.20 5.20±0.20 2.10±0.20
-0.00 -0.40

(mm)

Copyright  ANPEC Electronics Corp. 16 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Devices Per Unit

Package Type Unit Quantity
SOT-23-5 Tape & Reel 3000
SOT-89 Tape & Reel 1000
SOP-8P Tape & Reel 2500

Taping Direction Information

SOT-23-5

USER DIRECTION OF FEED

SOT-89

USER DIRECTION OF FEED

Copyright  ANPEC Electronics Corp. 17 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Taping Direction Information

SOP-8P

USER DIRECTION OF FEED

Classification Profile

Copyright  ANPEC Electronics Corp. 18 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Classification Reflow Profiles

Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly
Preheat & Soak
100 °C 150 °C
Temperature min (Tsmin)
150 °C 200 °C
Temperature max (Tsmax)
60-120 seconds 60-120 seconds
Time (Tsmin to Tsmax) (ts)

Average ramp-up rate

3 °C/second max. 3°C/second max.
(Tsmax to TP)
Liquidous temperature (TL) 183 °C 217 °C
Time at liquidous (tL) 60-150 seconds 60-150 seconds
Peak package body Temperature
See Classification Temp in table 1 See Classification Temp in table 2
(Tp)*
Time (tP)** within 5°C of the specified
20** seconds 30** seconds
classification temperature (Tc)
Average ramp-down rate (Tp to Tsmax) 6 °C/second max. 6 °C/second max.

Time 25°C to peak temperature 6 minutes max. 8 minutes max.

* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.

Table 1. SnPb Eutectic Process – Classification Temperatures (Tc)

3 3
Package Volume mm Volume mm
Thickness <350 ≥350
<2.5 mm 235 °C 220 °C
≥2.5 mm 220 °C 220 °C

Table 2. Pb-free Process – Classification Temperatures (Tc)

3 3 3
Package Volume mm Volume mm Volume mm
Thickness <350 350-2000 >2000
<1.6 mm 260 °C 260 °C 260 °C
1.6 mm – 2.5 mm 260 °C 250 °C 245 °C
≥2.5 mm 250 °C 245 °C 245 °C

Reliability Test Program

Test item Method Description
SOLDERABILITY JESD-22, B102 5 Sec, 245°C
HOLT JESD-22, A108 1000 Hrs, Bias @ Tj=125°C
PCT JESD-22, A102 168 Hrs, 100%RH, 2atm, 121°C
TCT JESD-22, A104 500 Cycles, -65°C~150°C
HBM MIL-STD-883-3015.7 VHBM≧2KV
MM JESD-22, A115 VMM≧200V
Latch-Up JESD 78 10ms, 1tr≧100mA

Copyright  ANPEC Electronics Corp. 19 www.anpec.com.tw

Rev. A.3 - Sep., 2012
APL5155

Customer Service

Anpec Electronics Corp.

Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050

Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838

Copyright  ANPEC Electronics Corp. 20 www.anpec.com.tw

Rev. A.3 - Sep., 2012