Electronic Systems

An Electronic System is a physical interconnection of components, or parts, that gathers various

amounts of information together

It does this with the aid of input devices

such as sensors, that respond in some way
to this information and then uses electrical
energy in the form of an output action to
control a physical process or perform some
type of mathematical operation on the
signal.
But electronic control systems can also be regarded as a process that transforms one signal
into another so as to give the desired system response. Then we can say that a simple
electronic system consists of an input, a process, and an output with the input variable to the
system and the output variable from the system both being signals.
There are many ways to represent a system, for example: mathematically, descriptively,
pictorially or schematically. Electronic systems are generally represented schematically as a
series of interconnected blocks and signals with each block having its own set of inputs and
outputs.
As a result, even the most complex of electronic control systems can be represented by a
combination of simple blocks, with each block containing or representing an individual
component or complete sub-system. The representing of an electronic system or process
control system as a number of interconnected blocks or boxes is known commonly as “block-
diagram representation”.

Block Diagram Representation of a Simple Electronic System

Electronic Systems have both Inputs and Outputs with the output or outputs being produced

by processing the inputs. Also, the input signal(s) may cause the process to change or may
itself cause the operation of the system to change. Therefore the input(s) to a system is the
“cause” of the change, while the resulting action that occurs on the systems output due to this
cause being present is called the “effect”, with the effect being a consequence of the cause.
In other words, an electronic system can be classed as “causal” in nature as there is a direct
relationship between its input and its output. Electronic systems analysis and process control
theory are generally based upon this Cause and Effect analysis.
So for example in an audio system, a microphone (input device) causes sound waves to be
converted into electrical signals for the amplifier to amplify (a process), and a loudspeaker
(output device) produces sound waves as an effect of being driven by the amplifiers electrical
signals.
But an electronic system need not be a simple or single operation. It can also be an
interconnection of several sub-systems all working together within the same overall system.
Our audio system could for example, involve the connection of a CD player, or a DVD player, an
MP3 player, or a radio receiver all being multiple inputs to the same amplifier which in turn
drives one or more sets of stereo or home theatre type surround loudspeakers.
But an electronic system can not just be a collection of inputs and outputs, it must “do
something”, even if it is just to monitor a switch or to turn “ON” a light. We know that sensors are
input devices that detect or turn real world measurements into electronic signals which can then
be processed. These electrical signals can be in the form of either voltages or currents within a
circuit. The opposite or output device is called an actuator, that converts the processed signal
into some operation or action, usually in the form of mechanical movement.
Types of Electronic System
Electronic systems operate on either continuous-time (CT) signals or discrete-time (DT) signals.
A continuous-time system is one in which the input signals are defined along a continuum of
time, such as an analogue signal which “continues” over time producing a continuous-time
signal.
But a continuous-time signal can also vary in magnitude or be periodic in nature with a time
period T. As a result, continuous-time electronic systems tend to be purely analogue systems
producing a linear operation with both their input and output signals referenced over a set period
of time.
For example, the temperature of a room can be classed as
a continuous time signal which can be measured between
two values or set points, for example from cold to hot or
from Monday to Friday. We can represent a continuous-
time signal by using the independent variable for time t, and
where x(t) represents the input signal and y(t) represents
the output signal over a period of time t.
Generally, most of the signals present in the physical world
which we can use tend to be continuous-time signals. For
example, voltage, current, temperature, pressure, velocity,
etc.
On the other hand, a discrete-time system is one in which the input signals are not continuous
but a sequence or a series of signal values defined in “discrete” points of time. This results in a
discrete-time output generally represented as a sequence of values or numbers.
Generally a discrete signal is specified only at
discrete intervals, values or equally spaced points in
time. So for example, the temperature of a room
measured at 1pm, at 2pm, at 3pm and again at 4pm
without regards for the actual room temperature in
between these points at say, 1:30pm or at 2:45pm.
However, a continuous-time signal, x(t) can be
represented as a discrete set of signals only at
discrete intervals or “moments in time”. Discrete
signals are not measured versus time, but instead
are plotted at discrete time intervals, where n is the sampling interval. As a result discrete-time
signals are usually denoted as x(n) representing the input and y(n) representing the output.
Then we can represent the input and output signals of a system as x and y respectively with the
signal, or signals themselves being represented by the variable, t, which usually
represents time for a continuous system and the variable n, which represents an integer value
for a discrete system as shown.

Interconnection of Systems
One of the practical aspects of electronic systems and block-diagram representation is that they
can be combined together in either a series or parallel combinations to form much bigger
systems. Many larger real systems are built using the interconnection of several sub-systems
and by using block diagrams to represent each subsystem, we can build a graphical
representation of the whole system being analysed.
When subsystems are combined to form a series circuit, the overall output at y(t) will be
equivalent to the multiplication of the input signal x(t) as shown as the subsystems are
cascaded together.

Series Connected System

For a series connected continuous-time
system, the output signal y(t) of the first
subsystem, “A” becomes the input signal of
the second subsystem, “B” whose output
becomes the input of the third subsystem, “C” and so on through the series chain
giving A x B x C, etc.
Then the original input signal is cascaded through a series connected system, so for two series
connected subsystems, the equivalent single output will be equal to the multiplication of the
systems, ie, y(t) = G1(s) x G2(s). Where G represents the transfer function of the subsystem.
Note that the term “Transfer Function” of a system refers to and is defined as being the
mathematical relationship between the systems input and its output, or output/input and hence
describes the behaviour of the system.
Also, for a series connected system, the order in which a series operation is performed does not
matter with regards to the input and output signals as: G1(s) x G2(s) is the same as G2(s) x G1(s).
An example of a simple series connected circuit could be a single microphone feeding an
amplifier followed by a speaker.

Parallel Connected Electronic System

For a parallel connected continuous-time system, each
subsystem receives the same input signal, and their
individual outputs are summed together to produce an
overall output, y(t). Then for two parallel connected
subsystems, the equivalent single output will be the
sum of the two individual inputs, ie, y(t) = G1(s) + G2(s).
An example of a simple parallel connected circuit could
be several microphones feeding into a mixing desk
which in turn feeds an amplifier and speaker system.

Electronic Feedback Systems

Another important interconnection of systems which is used extensively in control systems, is
the “feedback configuration”. In feedback systems, a fraction of the output signal is “fed back”
and either added to or subtracted from the original input signal. The result is that the output of
the system is continually altering or updating its input with the purpose of modifying the
response of a system to improve stability. A feedback system is also commonly referred to as a
“Closed-loop System” as shown.

Closed-Loop Feedback System

Feedback systems are used a lot in most practical electronic system designs to help stabilize
the system and to increase its control. If the feedback loop reduces the value of the original
signal, the feedback loop is known as “negative feedback”. If the feedback loop adds to the
value of the original signal, the feedback loop is known as “positive feedback”.
An example of a simple feedback system could be a thermostatically controlled heating system
in the home. If the home is too hot, the feedback loop will switch “OFF” the heating system to
make it cooler. If the home is too cold, the feedback loop will switch “ON” the heating system to
make it warmer. In this instance, the system comprises of the heating system, the air
temperature and the thermostatically controlled feedback loop.

Transfer Function of Systems

Any subsystem can be represented as a simple block
with an input and output as shown. Generally, the input
is designated as: θi and the output as: θo. The ratio of
output over input represents the gain, ( G ) of the subsystem and is therefore defined
as: G = θo/θi
In this case, G represents the Transfer Function of the system or subsystem. When discussing
electronic systems in terms of their transfer function, the complex operator, s is used, then the
equation for the gain is rewritten as: G(s) = θo(s)/θi(s)

Electronic System Summary

We have seen that a simple Electronic System consists of an input, a process, an output and
possibly feedback. Electronic systems can be represented using interconnected block diagrams
where the lines between each block or subsystem represents both the flow and direction of a
signal through the system.
Block diagrams need not represent a simple single system but can represent very complex
systems made from many interconnected subsystems. These subsystems can be connected
together in series, parallel or combinations of both depending upon the flow of the signals.
We have also seen that electronic signals and systems can be of continuous-time or discrete-
time in nature and may be analogue, digital or both. Feedback loops can be used be used to
increase or reduce the performance of a particular system by providing better stability and
control. Control is the process of making a system variable adhere to a particular value, called
the reference value.
In the next tutorial about Electronic Systems, we will look at a types of electronic control
system called an Open-loop System which generates an output signal, y(t) based on its present
input values and as such does not monitor its output or make adjustments based on the
condition of its output.

Reference:
https://www.electronics-tutorials.ws/systems/electronic-system.html