Proximate Analysis: Muhammad Asif 2K8-Vas-32 Luawms Uthal Balochistan

Proximate Analysis
MUHAMMAD ASIF 2K8-VAS-32

LUAWMS UTHAL BALOCHISTAN
Setting of Analytical Laboratory
Following things are required

• Oven • Dessicator
• Weighing Balance • Fiber Extraction Apparatus
• Furnace • Soxbelt Apparatus (Fat Digestion)
• Suction Pump • kjeldahl Apparatus
• Racks
Continue…
• Balance and oven are placed together so as to avoid the moisture loss
and less time is consumed.
• Dessicator is moisture absorbent having Ca and Silicate salts.
• Never place furnace near balance because its air current disturb
reading.
• Organic Substances - - - - - - - - 70 - 80oC
• Inorganic Substances - - - - - - - - - 100oC
Continue…
• For protein and fat digestion, fume hood with sliding roller used.
• Distillation apparatus should be placed near water supply and titration
flask.
• Acids and alkalis should be placed on lower side of rack.
• Fiber extraction apparatus and suction pump should be placed on same
shelf.
• Soxbelt apparatus and solvent should be on the same shelf.
Proximate Analysis
In 1865, for describing various feeds and fodders,

Hennebrg and Stobman at Weende Expi Station
Germany proposed a scheme of chemical
analysis, also called Weende Analysis
Scheme/Weende’s System of Analysis.
There are following analytical procedures used under
Proximate Analysis
Fraction Component
Moisture Water (VA and bases if present)
Crude protein Proteins, Amino acids, Amines, Amides,

Nitrates
Ether extract Fat, Oil, Waxes, Pigments, Sterols
Crude fiber Cellulose, Hemicellulose, Lignin
Ash Minerals, Silica
Nitrogen free extract Sugar, Starch, Protein

Food
Dry Matter Water
Inorganic Organic Birth
Mature
750 –
Minerals Carbohydrates 500gm/Kg
800gm/Kg
Nucleic Acid
Organic Acid
Lipid
Protein
Vitamins
Moisture
Moisture or water content is most important in a feed. It gives

information about the characteristics of feed whether it is succulent
or dry (bullkey feed stuff).
Moisture
• Moisture ↑ than 15% → promote growth of fungus and mold when

stored .
• Fermentation may also take place resulting in combustion.
Silage Moisture = 65 – 70%
Hay Moisture = 15%
• 1 gm of carbohydrate, protein & fat yield approximately 0.6, 0.4,
0.1 ml metabolic water on oxidation.
• Water content in feed also determine water requirement of an
animal.
Procedure
Dry Matter
Dry matter is the constant wt. of

sample when heated at 100oC but
it is suitable for inert materials,
not for organic substances.
All organic materials are dried at
70 – 75oC through Three methods.
• Low temperature drying
• High temperature drying
• Freeze drying
Dry Matter
In low temperature drying, some labs

adopted this method , vacuum drying
oven 30oC temps along with 16mm Hg of
pressure. This will reduce losses of
variable substances. In high temperature
materials are dried at 100oC for DM
estimation and 70 - 75oC for analysis of
organic substances. Freeze drying is
adopted to have minimum change In
chemical composition but it can not be
used for DM.
Determine the CP% of given sample through
Proximate Analysis
Proximate Analysis
Detergents:
Mixed indicator for ammonia titration. Mix 10 mL of Bromocresol
green (0.1%) + 2 mL of methyl red (0.1%).
• Sulfuric acid solutions, 0.1 N (0.25%) and Concentrated sulfuric
acid, 98%.
• Digestion mixture :K2SO4 + CuSO4. + FeSO4
• Sodium hydroxide solution:(4%) Dissolve 40 gm sodium hydroxide
in 80 mL of distilled water and dilute it to 100 mL with distilled
water.
• Boric acid solution: (2%)
Dissolve 20 gm boric acid per liter of distilled water.
Proximate Analysis
Procedure:
There are three steps.
• Digestion
• Distillation
• Titration
1. Digestion
• Take specific volume (1 – 2g) of sample, then add 25 – 30ml conc. H2SO4
and 5gm digestion mixture. Then put it in heater(macro kjeldahl) for
5 – 6hrs. With occasional stearing till light green or colourless solution
appear. Then let it cool and make its volume upto 250ml in the volumetric
flask.(kjeldahl flask)
Digestion Mixture:
FeSO4 : CuSO4 : K2SO4
1 : 2 : 20
• FeSO4 is used to avoid bumping.
• CuSO4 is used as catalyst.
• K2SO4 is used to minimize the boiling point.
2. Distillation
Take 10ml sample (ariquotes)(Digested

Diluted Material) and put it in distillation
assembly, then add 10ml 40% NaOH and
close it. Put 10ml of 2% boric acid in
conical flask. Put it under the tip of cond-
ensor of distillation assembly. Put 1 – 2
drops of phenolphthaein a methyl red
shocking.
Pink → Brown/ Yellow
3. Titration
In titration we use N/10 or

N/100 H2SO4. After NH3
and boric acid reaction
.find the volume of
sulphuric used at end
point of titration
Calculation
End Point
Determine the E.E% of given sample through
Proximate Analysis
• Crude fat/ E.E
Crude fat ether extract contains all type of fats volatile and none
volatile fatty acids containing fats like lipids, oils, waxes phospholipids
etc.
principle
• Ether extract of the feed/food sample is carried out in Soxtherm
extraction unit. It facilitates that always fresh ether repeatedly
dissolves the fat from the sample placed in extractor tube. In this unit
fat is dissolved in ether. The excess of the ether is then recovered
leaving the extracted fat in the beakers. The beakers are placed in the
oven at 1030C for 30-40 minutes.
Weight of ether extract
Ether Extract (%) = ------------------------------- X 100
Weight of sample
Determine the E.E% of given sample through

Proximate Analysis
• REAGENT
a) Diethyl ether or
b) Ether solvent (Benzene ether) or
c) Mixture of (CHCl3 + Acetone)
Procedure
• Weigh 1.5 to 4.0 gm sample (into a thimble) or on a piece of filter paper 10 x 10

cm. Fold it to form a packet. Staple it such that no feed particles can escape from
it.
• Place the packet containing sample in the thimble and fix it under the condenser.
Add 100 ml of diethyl ether to the solvent beaker and place it under condenser
with screw ring, which is tightened as much as possible by hand. Turn on the water
that cools the condenser. Raise the hot plates until they are in contact with the
beakers and turn on the heaters. Check for ether leaks after the ether starts to
evaporate and condense. Allow the extraction process for 40 minutes.
• After the completion of extraction, lower the heater and allow the thimble to drain
empty. Remove the sample and place the reclaiming tubes under the condenser.
Raise hot plate and distill ether into the reclaiming tube. Remove beaker, pour
ether from reclaiming tubes into a container for reuse.
• Dry the ether extract in a 1050C explosion proof oven for 30 minutes. Cool in
desiccator to room temperature and weigh.
Calculations
Weight of ether extract

Ether Extract (%) = ------------------------------- X 100
Weight of sample
Determine the C.F% of given sample through
Proximate Analysis
PRINCIPLE
Plant material is treated with dilute acid and alkali solutions

under boiling condition. This treatment removes the soluble
substances leaving the insoluble in the form of residue as crude
fiber.
Reagents
• Sulfuric acid solution:

• Dissolve 1.25 gm H2SO4 in 100 ml distilled water. Check normality
by titration and adjust if necessary to 0.255 N.
• Sodium hydroxide solution:
• Dissolve 1.25 gm NaOH in 100 ml distilled water (free from
Na2CO3). Check normality by titration and adjust if necessary to
0.313 N.
• Ethyl alcohol
Procedure
• The residue left after the extraction of crude fat is used for
determination of crude fiber (see method of ether extraction on
previous page).
• Transfer the extracted residue to the digestion container.
• Add 200 mL of 1.25% sulfuric acid solution into the digestion
container and heat it after covering with condenser.
• After boiling for 30 minutes cool the mixture and filter it with a linen
cloth in a filtration flask. Use vacuum pump if necessary. Wash the
residues thoroughly with boiling water.
• Put the residue back into the container and add 200 ml of 1.25%
sodium hydroxide solution and boil it for 30 minutes.
• After boiling cool the mixture and filter it with linen cloth as before.
Wash the sample with boiling water.
• Give final washing with ethyl alcohol (5-10 mL).
Procedure cont.
• Transfer the residue to a tared crucible.

• Dry the sample in oven at 1050C overnight.
• Cool the dried sample to room temperature in a dessicator and weigh it.
• Ignite the contents of crucible on oxidizing flame, till no fumes are
evolved.
• Ignite the contents of crucible in a muffle furnace at 5000C for 1 hour.
• After ignition transfer the crucible into a dessicator to cool and then weigh
• Note the loss of weight due to ignition as crude fiber.
Calculations
Loss of weight due to ignition

Crude fiber (%) = ----------------------------------------- X 100
Weight of sample before extraction of fat
Determine the Crude Ash of given sample
through Proximate Analysis
PRINCIPLE
On oxidation of feed/food material at higher temperature it
oxidizes all the organic matter to CO2, H2O and NO2 leaving
mineral matter as oxides of the metals known as ash.
Procedure
• Place a clean crucible in a muffle furnace at 6000C for one hour. Transfer
crucible from furnace to a dessicator and cool to room temperature.
• Weigh by difference 1.5 to 2 gm of sample into a pre-weighed porcelain
crucible.
• Heat the crucible on oxidizing flame till no smoke is evolved.
• Place the crucible in a muffle furnace at 5500C for four hours.
• After ashing transfer the crucible to a dessicator and cool to room
temperature.
• Weigh the crucible containing ash as quickly as possible to prevent moisture
absorption.
• Calculate the weight of ash by subtracting the weight of empty crucible from
the weight noted in step 6.
• Save the ash sample if mineral determination is to be done.
Calculations
Weight of ash
Ash (%) = --------------------------- X 100
Weight of sample
THANK YOU

Proximate Analysis: Muhammad Asif 2K8-Vas-32 Luawms Uthal Balochistan

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Proximate Analysis: Muhammad Asif 2K8-Vas-32 Luawms Uthal Balochistan

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Proximate Analysis: Muhammad Asif 2K8-Vas-32 Luawms Uthal Balochistan

Uploaded by

Copyright:

Available Formats

Proximate Analysis

MUHAMMAD ASIF 2K8-VAS-32

Following things are required

In 1865, for describing various feeds and fodders,

Moisture Water (VA and bases if present)

Crude protein Proteins, Amino acids, Amines, Amides,

Ether extract Fat, Oil, Waxes, Pigments, Sterols

Crude fiber Cellulose, Hemicellulose, Lignin

Ash Minerals, Silica

Nitrogen free extract Sugar, Starch, Protein

Moisture or water content is most important in a feed. It gives

• Moisture ↑ than 15% → promote growth of fungus and mold when

Dry matter is the constant wt. of

In low temperature drying, some labs

Take 10ml sample (ariquotes)(Digested

In titration we use N/10 or

Determine the E.E% of given sample through

• Weigh 1.5 to 4.0 gm sample (into a thimble) or on a piece of filter paper 10 x 10

Weight of ether extract

Plant material is treated with dilute acid and alkali solutions

• Sulfuric acid solution:

• Transfer the residue to a tared crucible.

Loss of weight due to ignition

You might also like