This document provides an overview of reinforced concrete slab design. It defines one-way and two-way slabs and explains how to classify and analyze each type. For one-way slabs, it describes how to determine load distribution and design typical slabs. For two-way slabs, it discusses support conditions, load distribution analysis, and design of simply supported and restrained slab systems. The document aims to teach students how to identify slab types, apply loading arrangements, and complete the basic design of one-way and two-way reinforced concrete slabs.
This document provides an overview of reinforced concrete slab design. It defines one-way and two-way slabs and explains how to classify and analyze each type. For one-way slabs, it describes how to determine load distribution and design typical slabs. For two-way slabs, it discusses support conditions, load distribution analysis, and design of simply supported and restrained slab systems. The document aims to teach students how to identify slab types, apply loading arrangements, and complete the basic design of one-way and two-way reinforced concrete slabs.
This document provides an overview of reinforced concrete slab design. It defines one-way and two-way slabs and explains how to classify and analyze each type. For one-way slabs, it describes how to determine load distribution and design typical slabs. For two-way slabs, it discusses support conditions, load distribution analysis, and design of simply supported and restrained slab systems. The document aims to teach students how to identify slab types, apply loading arrangements, and complete the basic design of one-way and two-way reinforced concrete slabs.
This document provides an overview of reinforced concrete slab design. It defines one-way and two-way slabs and explains how to classify and analyze each type. For one-way slabs, it describes how to determine load distribution and design typical slabs. For two-way slabs, it discusses support conditions, load distribution analysis, and design of simply supported and restrained slab systems. The document aims to teach students how to identify slab types, apply loading arrangements, and complete the basic design of one-way and two-way reinforced concrete slabs.
Design of Slab by Dr. Sharifah Maszura Syed Mohsin Faculty of Civil Engineering and Earth Resources [email protected]
Design of Slab by Sharifah Maszura Syed Mohsin
Lesson Outcome
At the end of the lesson, students should be able to:
• Identify one way slab or two way slab • Define and explain the classification of solid slab • Define and explain loading arrangement and method of analysis • Define and calculate the load distribution for one-way slab analysis • Design typical one-way slab • Define and calculate the load-distribution for two-way slab analysis. • Design typical two-way slab
Design of Slab by Sharifah Maszura Syed Mohsin
Introduction
• Slab is horizontal plate elements forming floor and
roof in building. • Slab is a structural element with small overall depth/thickness (h) as compared to the width (b) and its span (L). • The bending behaviour of a slab is similar to beam. • Generally, the design of a slab is almost similar to the design of beam.
Design of Slab by Sharifah Maszura Syed Mohsin
Types of slab
There are various types of reinforced concrete slabs.
1. Solid slab – Only this will be covered in this course.
2. Ribbed slab 3. Flat slab 4. Waffle slab
Design of Slab by Sharifah Maszura Syed Mohsin
Design of Reinforced Concrete Slab
• Basically, the design as easier as compared to
beam design. • This is because: 1. In the design calculation, slab width, b is fixed to 1 m (b =1000 mm). 2. Shear stress in slab is very small except when the slab is subjected to point loads. 3. Compression reinforcement is seldom required. 4. Slab usually support UDL.
Design of Slab by Sharifah Maszura Syed Mohsin
Analysis method
1. Elastic Analysis 2. Moment and shear coefficient from BS8110 3. Yield line analysis 4. Table 6.3 Reinforced Concrete Designer Handbook by Reynold
Design of Slab by Sharifah Maszura Syed Mohsin
Design of Solid Slab
• RC solid slabs can be designed as spanning in
one way or two ways.
• This classification depends on the supports
and the dimension of the slab (Ly/Lx ratio).
Design of Slab by Sharifah Maszura Syed Mohsin
One way slab
• When the slab is supported only on two sides OR
• When the value of Ly/Lx ratio is more than 2.0 for slabs supported on its four sides. • Main reinforcement is designed only in one- direction. • Transverse reinforcement will be applied in another direction.
Design of Slab by Sharifah Maszura Syed Mohsin
One way slab
Design of Slab by Sharifah Maszura Syed Mohsin
One way slab
Design of Slab by Sharifah Maszura Syed Mohsin
Two way slab
• Happens when the value of Ly/Lx ratio is equal to or
less than 2.0.
• Main reinforcement is designed in both directions
Design of Slab by Sharifah Maszura Syed Mohsin
Two way slab
Design of Slab by Sharifah Maszura Syed Mohsin
Type of Two way slab
• Simply supported two way slab (unrestrained).
– Slab only consist of one panel and the sides of the slab is not restrained against lifting. – Refer Table 3.13 for bending moment coefficient.
• Restrained two way slab (continuous).
– Slab which is connected to other slabs and supported in its four sides. – Refer Table 3.14 and Table 3.15 for shear force and bending moment coefficient – There are 9 different types of support conditions.
