0% found this document useful (0 votes)
967 views4 pages

Method of Assumed State PDF

This document discusses diode models and circuit analysis methods. It describes the ideal diode model and constant voltage drop model, where a diode is considered ON if current is positive or voltage is above the threshold, and OFF otherwise. It introduces the method of assumed states for analyzing multi-diode circuits, which involves guessing diode states, analyzing the resulting linear circuit, and verifying the guesses. Examples are provided for further understanding.

Uploaded by

Abid Abrar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
967 views4 pages

Method of Assumed State PDF

This document discusses diode models and circuit analysis methods. It describes the ideal diode model and constant voltage drop model, where a diode is considered ON if current is positive or voltage is above the threshold, and OFF otherwise. It introduces the method of assumed states for analyzing multi-diode circuits, which involves guessing diode states, analyzing the resulting linear circuit, and verifying the guesses. Examples are provided for further understanding.

Uploaded by

Abid Abrar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

IV curve of a real diode

Anode (𝑣" ) Cathode (𝑣$ )

Forward Bias: 𝑣" > 𝑣$ [𝑣& positive]


Reverse Bias: 𝑣" ≤ 𝑣$ [𝑣& negative]

./
Equation: 𝑖& = 𝐼+ ,𝑒 01 − 14
where 𝑣& (= 𝑣" − 𝑣$ ) is the voltage across the diode, 𝑖& is the current through the
diode (from anode to cathode) and 𝑉8 , called the thermal voltage, is a temperature
dependent constant. For temperature 𝑇 = 300𝐾, 𝑉8 = 25 𝑚𝑉.

2. Diode models (for rapid analysis)


2.1. Ideal diode model

In this model, we say the diode is ON if the current through the diode is
positive and replace it with a short circuit. Hence, the voltage across the
diode is zero in this case. If the voltage across the diode is negative (𝑣$ ≥ 𝑣" ),
then we say the diode is OFF and replace it with an open circuit. Thus, in this
case, the current through the diode is zero.
So, to check if a diode is ON, we need to check the current through it (if
positive, then ON) and to check if a diode is OFF, we need to check the
voltage across it (if negative, then OFF).

Remember 1:
We define the diode current 𝑖& from anode to cathode. So,

in this case the current 𝑖& is positive and the diode is ON. And for this case

the current 𝑖& is negative and the diode is not ON (in fact, this is not
possible).

Remember 2:
We define the diode voltage 𝑣& as the voltage of anode with respect to the
voltage of cathode. For example:

In this case, the voltage 𝑣& across the diode is negative and the diode is OFF.
Again

in this case, the voltage 𝑣& across the diode is positive and the diode is not
OFF (in fact, this is not possible).
2.2. Constant voltage drop model

In this model, we say the diode is ON if the current through the diode is
positive and replace it with a voltage source. Hence, the voltage across the
diode is constant (𝑉A ) in this case. If the voltage across the diode is less than
or equals to 𝑉A (𝑣& ≤ 𝑉A ), then we say the diode is OFF and replace it with an
open circuit. Thus, in this case, the current through the diode is zero. Typical
value of 𝑉A for silicon diode is 0.7𝑉. For ideal diode model, 𝑉A = 0𝑉.

3. Method of assumed state [From Neaman]


Analyzing multi-diode circuits requires determining if the individual devices are ON
or OFF. In many cases, the choice is not obvious, so we must initially guess the state
of each device, then analyze the circuit to determine if we have a solution consistent
with our initial guess. To do this, we can:

i. Assume the state of a diode. If a diode is assumed ON, the voltage across the
diode is assumed to be 𝑉A (Voltage source or short circuit). If a diode is assumed
to be OFF, the current through the diode is assumed to be zero (Open circuit).

ii. Analyze the “linear” circuit with the assumed diode states.

iii. Evaluate the resulting state of each diode.

If the initial assumption were that a diode is OFF and the analysis shows that
𝑉& ≤ 𝑉A , then the assumption is correct. If, however, the analysis actually
shows that 𝑉& > 𝑉A , then the initial assumption is incorrect.

Similarly, if the initial assumption were that a diode is ON and the analysis
shows that 𝐼& > 0, then the initial assumption is correct. If, however, the analysis
shows that 𝐼& ≤ 0, then the initial assumption is incorrect.

iv. If any initial assumption is proven incorrect, then a new assumption must be
made and the new “linear” circuit must be analyzed. Step iii must then be repeated.
4. Examples
Please go through the following examples for better understanding. See class notes
for detailed solutions of these problems.

Sedra: Example 4.2, Exercise 4.4


Neaman: Example 2.9, 2.10, 2.11 Exercise 2.9, 2.10, 2.11

You might also like