Futaba Standard

Plastic Mold Components

Blue Book
 Ordering Machining
Futaba
Standard
Plastic M
old Compo
Blue Bo
ok nents

Please use these catalogs in conjunction!

Additional processing
Additional processing can now
be ordered with simple catalog
codes.

Additional Processing Machining

Rough Pockets Machining − Slide Core Groove

Machine slide-core shaped pockets in mold plates.
Application Mold bases, cavity retainer sets, cavity retainer sets for die cast Pocket machining applicable plates Machining speciÀcation of circular pockets
Finished dimension
The PL side and the UR side of each plate are as follows: M X
For circular pocket, M is a
Machining dimension ※ We machine pockets leaving a ¿nishing allowance of approximately 1 mm PL side dimension to the contact
Additional Plate Q
with respect to the ¿nished dimension. point with the circular hole
Plate S
1 1 Please specify the dimension of pockets with their ¿nished dimensions. as shown on the left.
1

Additional Plate V
Plate B In the cases where the
PL side
B

Plate U
Additional Plate W Plate A groove is located on the top,
Groove width and depth Additional Plate N bottom or right, M is also
Y

Additional Plate O
Groove width ( A or B DIMM shown below) 10≦（A or B）＜42 42≦（A or B）＜55 55≦（A or B） Additional Plate X measured to the contact
Plate R Datum
Groove depth Z Z≦（A or B）×3 Z≦130 Z≦150 This section is also grooved. point with the hole likewise.
UR side UR side
※ The maximum machining depth of groove depth Z varies depending on the width of the groove.
※ For groove depth not shown in the above table, consult our sales office. ※ For plates not shown the above, specify with a drawing, etc.
Machining

Machining

Catalog No. MKKMA/PL (Machine grooves on PL surface side) Catalog No. MKKMB/PL (Machine grooves on PL surface side)
Rough Pockets Machining – Side Core Groove

Rough Pockets Machining – Side Core Groove

Catalog No. Plate code A B Z ＊1 X Y M ＊2

A X X A
Additional plate In 0.1 mm In 0.1 mm
MKKMA/PL −
R (Plate R) O (Plate O) steps steps In 0.1 mm
A (Plate A) N (Plate N) In 0.1 mm steps
M

Separately Separately − −
MKKMB/PL
specify specify
S (Plate S) Q (Plate Q) steps In 0.1 mm In 0.1 mm
B

pockets pockets
B (Plate B) V (Plate V)
Separately Separately steps steps
specify specify In 0.1 mm
MKKMC/PL − −
U (Plate U) W (Plate W) steps
Y

pockets pockets In 0.1 mm

Y

X (Plate X) In 0.1 mm steps In 0.1 mm

M Datum Datum M MKKMD/PL −
Datum Datum Additional plate spec. P.38 steps steps
PL surface side PL surface side
＊1. Z ≦ depth of pocket to be speci¿ed separately (For through pockets, Z≦plate thickness – 5)
Z

Z
Z

＊2. This is a through groove to a pocket. Specifying blind grooves extending halfway is not allowed with this option.

Specify
※ Be sure to specify pockets separately. Specifying slide core grooves only is not allowed.
Applicable to Plate Q, S, V, B, U, W and X Applicable to Plate R, O, N and A Applicable to Plate Q, S, V, B, U, W and X Applicable to Plate R, O, N and A ※ Pocket machining details P.204
※ Pocket machining to be speci¿ed separately P.206 ∼ 213
Catalog No. MKKMC/PL (Machine grooves on PL surface side) Catalog No. MKKMD/PL (Machine grooves on PL surface side)

Separately Separately How to order

specify specify Separately Separately
pockets pockets specify specify
Plate code A B Z X Y M
B

pockets pockets Catalog No.

MKKMA/PL B A80 Z15 X70 Y200 M60

M

A X Datum Datum X A M X Datum Datum X M

PL surface side PL surface side ※ If creating two grooves as shown on the left, repeat the specifying twice.
If creating three or more grooves, repeat it multiple times accordingly.
Z

Separately
An example of order:
Applicable to Plate Q, S, V, B, U, W and X Applicable to Plate R, O, N and A Applicable to Plate Q, S, V, B, U, W and X Applicable to Plate R, O, N and A specify ② Specify ① MKKMC/PL−B−A40−Z15−X55−M40

You can
pockets
Specify ② MKKMB/PL−B−B80−Z20−Y60−M40
※ The position of the datum plane is that viewed at the time when mold plates on both the fixed and moving sides are open (position ①
viewed from the parting line surface).
Datum
※ The slide core grooves cannot be specified from the UR surface side. Please specify with a drawing, etc.

216 For shapes and dimensions not listed above, please specify with a drawing or consult our sales of¿ce. 217

parts
※To ensure
read the “S
 Easy and Effortlessly
Additional Processing Parts Installation

Added Puller Bolts − AH1

Install puller bolts M-PBAH and M-PBCH. For details on the installation speci¿cations, see pages 148 to 153.
Position code S021 Position code S023 Position code S041
Puller bolt M-PBAH P.310 M-PBCH P.308
A A A
Application Mold bases D series and F series A/2 A/2 A/2

Catalog No. PPBAH1 Ground shank type

φD2

KL(mold plate DIMM)

KL(mold plate DIMM)

KL(mold plate DIMM)

If puller bolts are shorter than the
thickness of Plate A, the clearance hole will
M-PBCH not be provided only on the movable side.

B
H

B/2

B/2
S1

T
Plate T φD1

V
φD3

Y
Plate R

R
Installation

Installation
J
F
φE Datum Datum Datum

Parts

Parts
X X X

G
Plate A φD1 KW (mold plate DIMM) KW (mold plate DIMM) KW (mold plate DIMM)

A
P
Plate S

Added Puller Bolts – AH1

Added Puller Bolts – AH1

Plate A
Position code S022 Position code S024 Position code S042
Plate B A A

L
A/2 A/2

S2
Plate U φD φD2

KL(mold plate DIMM)

KL(mold plate DIMM)

KL(mold plate DIMM)
M-PBAH

Plate C

B
B

B/2
H

B/2
B/2

Y
Y
Plate L

L0
X Datum X Datum X Datum

※ If installing either or both of additional Plate O or/ KW (mold plate DIMM) KW (mold plate DIMM) KW (mold plate DIMM)
Diameter in the case of installing additional plates: Additional plate speci¿cation P.38 and Plate N, specifying E dimension and G=0,
 Diameter of Plate O and N → φD1 If E dimension is speci¿ed, however, φE is used. counterbore holes in Plate A will be eliminated
 Diameter of Plate Q, Plate V, Plate W and Plate X → φD2. and φ E through hole will be provided.
L dimention of Puller bolt M-PBAH
D L
D D1 D2 D3 Ｚ Ｐ＊1 E ＊1 G ＊1 J ＊1 H T R V F 10 50 60 70 80 90 100 110 120 130 140 150 160 170 180
Reccomended value
13 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 280
10 11 19 7 T-Z≧5 ＊2 P≦80 15 to 60 19 22 24 8
16 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 280 300
13 14 21 9 P≦100 In 1 mm 23 27 29 See When 8
When 20 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 280 300 350
16 17 27 11 P≦110 steps 28 37 table J≦7 R=10, 13 See page 152
D=10, 13 25 170 180 190 200 210 220 230 240 250 260 280 300 350
20 21 31 13 P≦130 provided 34 42 below J≦5 13
25 26 36 17 T-Z≧4 ＊2 P≦140 E≧D+5 41 52 18
Catalog No. D L Z P E G J Position code A B X Y Optional spec.
＊1. Specify P, E, G, J as necessary. Relation of counterbore diameter E and depth G In In 1 mm
10 S021 steps − In In PSR CCE
P+G+5≦A (this formula is not a guarantee of strength). Select 1 mm In 1 mm steps
＊2. This formula is not a guarantee of strength. E G max 13 1 mm steps 1 mm steps EHD MHD
from steps S022 −
※ Mold opening stroke between Plate T and Plate R 15 to 19 G≦50 PPBAH1 16 See left table In CRD CRM
S1=Z+V-T  Z=T+S1-V  V=T+S1-Z 20 to 27 G≦60 above See S023 In When When
20 1 mm EPAT
S024 X=KW/2, Y=KL/2,
※ Mold opening stroke between Plate R and Plate A 28 to 34 G≦80 table Left Omit this if unnecessary 1 mm steps
25 S041 omit X omit Y See page 149
S2=L-A+P-J  P=S2+A+J-L  L=S2+A+J-P  J=L+P-S2-A 35 to 44 G≦90 table S042 steps
※ If the distance from the head of puller bolt to the next plate is L0＜1, φD2
45 to 60 G≦100
through hole will be provided in the next plate as well.

How to order

Catalog No. D L Z P E G J Position code

PPBAH1 D13 L180 Z21 P15 E29 G30 J3 S041
A B X Y Optional spec.
A185 B100 X115 Y125 PSR/TF25/LS50

164 For shapes and dimensions not listed above, please specify with a drawing or consult our sales of¿ce. 165

Parts installation
Parts can now be mounted easier and
more effortlessly than ever before.

From MOLDZUKAN 3D mode version

additional processing
specify additional machining or
installation easily with a mouse.
proper and safe use of the products, please
Safety Precautions” at the end of this catalog.
Plastic Mold Standard Components
2-Plate Type S series

D & E series

3-Plate Type F & G series

H series

To ensure proper and safe use of the products,

please read the “Safety Precautions” listed at
the end of this catalog before using the products QMC series

Cassette-type Sumitomo cassette type

NISSEI FP SYSTEM
Mold base
Cavity Retainer Sets
Cavity retainer sets
Cavity Retainer Sets
For Die Cast

Additional machining
Additional
Parts installation
processing
Specification change

Guide parts

Mold parts
Mold components

2
 S series
2-Plate Type
High rigidity type with wider spacer blocks High rigidity type
2-plate structure
mold base used for Standard type with a broad range of mold plate sizes Standard type
side gate, etc.
Product sizes from 5585 to 9010 are standardized. Each dimension can be specified freely Large type

D & E series
3-Plate Type
High rigidity type with wider spacer blocks High rigidity type
3-plate structure
mold base used for
pin-point gate, etc.
Standard type with a broad range of mold plate sizes Standard type

F & G series
3-Plate Type
3-plate structure
High rigidity type with wider spacer blocks High rigidity type
mold base guided
only with support
pins for wider
Standard type with a broad range of mold plate sizes Standard type
effective space

H series
3-Plate Type
3-plate structure
mold base with the A standard for long shaped molds with a split mold or a slide mechanism
pins concentrated at
four corners

Mold Bases
Cassette
Futaba developed cassette type mold base that consists of an insert unit and a holder, which provides high versatility.

Cassette type mold base designed to Sumitomo Heavy Industry’s MINIMAT series mini-size injection molding machine specification that
supports each maker’s 8 to 25 ton horizontal molding machines.

Nissei Resin Industry Co. developed cassette type mold base for a new production system, which consists of a unit mold and base block

Retainer Sets
Cavity
Standard for cavity retainer set, which consists of cavity plates (fixed and moving halves) and stripper plate.

Standard for cavity retainer set for die cast, which consists of cavity plates (fixed and moving halves).
A relief and two-side clamp slots are machined to prevent troubles even when any casting debris enters.
For Die Cast
Cavity Retainer Sets

Available
as a separate
volume
Technical data
Product data/

3
 How to use catalogs

For plastic mold components, please use the

following two catalogs.

Standard mold base selections

An extensive lineup in both size and type. We respond to different
variations of requests by changing standard mold base specifications.

High Rigidity Type

S Series 1520 TD Technical Data P.787 STD Standard type P.88
︲2 PlateType

■ How to order
S Series

Clamping plate spec. TW

Clamping type
Bolt-fastening type
200
230
■ Order example MDC SA 1520 30 30 60 S V B N Option

TW Type SA SB SC SD
150
High Rigidity type

Nominal Dimension
38 70 38
20 25 30 35 40 50
M12 A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50
B DIMM 60 70 80
Futaba if there is any addition or
change to the specification.
1
Futaba Standard
5
C DIMM 50 60 70 2 Plastic Mold Components
82

34
Specification of ejector plate
0
Width of clamping
plate TW
Orientation of
guide
B
D
Counterbore type
Blue Book
106
164

182
200

Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
80

U DIMM
12 Y 200 V 30
Return pin

W 40
Z 230 — Types without backing plate

2 X 4-M10 28
16 52 ■ How to order optional specification
Guide pin

4-M6 114 Datum plane ■ Order example MDC SB 1520 40 30 50 S V B N / S30 / #FK / #EH
120 Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
◆ High rigidity type Additional Specifications other than the above are also available.
Standard type P.88 Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
Mold base specification which features wider spacer block than the standard type processing
change ※ Details ☞ P.260 Processing & Mold Parts Edition”for details.
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype SDtype

B 15 A 20
B A 20

B 15 A 20
A 20

Plate S
Plate S
B
U
U

13
13

13

13
C
C

C
15
15

15

15
20
20

20

20

28 29

BLUE BOOK Plastic

Mold Components Vol. 1

4
 Additional mold base processing selections
In response to a wide variety of requests, we have significantly
expanded the menu of available machining and parts installation.
Additional Processing Additional Processing Overview

Additional Processing Overview − Parts Installation

Locating ring Locating ring
cessing Overview

cessing Overview
Additional Pro-

Additional Pro-
P.86∼ P.86∼
Puller bolt
P.148∼

Sprue bushing
Sprue bushing P.92∼
Additional Processing Overview – Parts Installation

Additional Processing Overview – Parts Installation

P.92∼

Mold opening prevention Plate

P.182∼
PL puller
P.180 Tension link
P.172∼

Taper guide pin set

P.98∼

Support pillar Eye bolt Coil spring

P.142∼ P.231 P.134∼
Base spacer
P.188
Ejector guide pin Stop pin
P.110∼ Ejector rod P.140
P.146

Locating Ring Addition Sprue Bushing Addition Puller Bolt Addition Tension Link Addition
■ Added Locating Rings − Overiview ...................................86 ■ Added Sprue Bushings − Overview ..................................92 ■ Added Puller Bolts − Overview........................................148 ■ Added Tension Links − Overview ....................................172
■ Added Locating Rings − ① ...............................................88 ■ Added Sprue Bushings − Bolts Type.................................94 ■ Added Puller Bolts − B1 ..................................................154 ■ Added Tension Link M-HLA ...............................................176
■ Added Locating Rings − ② ...............................................90 ■ Added Sprue Bushings − Shoulder Type ..........................96 ■ Added Puller Bolts − B2 ..................................................156 ■ Added Tension Link M-HLB ...............................................178
■ Added Puller Bolts − B3 ..................................................158
■ Added Puller Bolts − B4 ..................................................160
Taper Guide pin Addition Ejector Guide Pin Addition
■ Added Puller Bolts − B5 ..................................................162 Spring Addition
■ Added Taper Guide Pin Sets − Overview ..........................98 ■ Added Guide Pins and Bushings − Overview .................110 ■ Added Puller Bolts − AH1 ................................................164
■ Added Taper Guide Pin Sets M-TLCS, M-TLDS ...............104 ■ Added Ejector Guide Pin M-EGA ......................................120 ■ Added Puller Bolts − A1 ..................................................166 ■ Added Springs − Overview..............................................134

Available
■ Added Taper Guide Pin Sets M-TLGS, M-TLHS ...............106 ■ Added Ejector Guide Pin M-EGB ......................................122 ■ Added Puller Bolts − AH2/A2 ..........................................168 ■ Added Springs − ① ........................................................136
■ Added Taper Guide Pin Set M-TLBS.................................108 ■ Added Ejector Guide Pin M-EGC ......................................124 ■ Added Puller Bolts − Standard Position ..........................170 ■ Added Springs − ② ........................................................138
■ Added Ejector Guide Pin M-EGBM ...................................126
■ Added Ejector Guide Pin M-EGCM ...................................128
Base Spacer Addition PL Puller Addition Addition of Stop Pin or Stop Ring
■ Added Ejector Guide Pin M-GPHF and M-GPA ................130

as a separate
■ Added Base Spacer .........................................................188 ■ Added Ejector Guide Pins and Bushings − Standard Position....132 ■ Added PL Pullers ...............................................................180 ■ Added Stop Pins or Stop Rings .........................................140

Support Pillar Addition Mold Opening Prevention Plate Addition Ejector Rod Addition Eye Bolt Addition
■ Added Support Pillars − Overview ..................................142 ■ Added Mold Opening Prevention Plate − Overview ........182 ■ Added Ejector Rods ..........................................................146 ■ Added Eye Bolts ................................................................231
■ Added Support Pillar .........................................................144 ■ Added Mold Opening Prevention Plate

volume
(at one place) ....................................................................184
■ Added Mold Opening Prevention Plate “Additional processing speci¿cations” are provided to show customers how to order additional processing. When designing molds, various
(at two or four places) .......................................................186 conditions such as strength and accuracy need to be taken into account. Therefore, we shall not be responsible or liable for any loss or
damage of any kind incurred as a result of, or in connection with your use of additional processing speci¿cations or selection of mold bases.

16 17

Mold parts selections

In response to diversified needs of customers,
we have significantly expanded the menu of mold
BLUE BOOK Additional
parts that can be installed in the mold bases.
Mold Base Processing &
Mold Parts Mold Parts General Table of Contents

General Table of Contents 1

Mold Parts Edition Vol. 1
Mold
Insert
opening
Blocks &
control
Plates
parts

High-precision plates Disc spacers

Product name Angular pins Product name Ground puller bolts
High-precision milling Ànish High-precision grinding Ànish For M-TLBS
Catalog No. HF HG M-DSA M-DSB M-DSC M-DSD M-DSE M-DSF M-AGA Catalog No. M-PBCH M-PBAH
Page P.262 P.264 P.301 P.302 P.303 Page P.308 P.310

Guide &
Positioning
Parts

Guide pins -head type- Straight guide pins

Product name With No Press-Àt length designa- Press-Àt length designation Press-Àt length designa- Press-Àt length designa- Press-Àt length designation Puller bolts
oil groove oil groove tion type (no oil groove) type (with spiral oil groove) tion type (no oil groove) tion type (with oil groove) type (with spiral oil groove) Tension links
Puller bolt collars
Catalog No. M-GPA M-GPH M-GPHF M-GPHFS M-GPSF M-GPSFR M-GPSFS M-PBC M-PBA M-PBB M-PCA M-PCB M-HLA
Page P.274 P.278 P.279 P.280 P.282 P.283 P.284 P.312 P.313 P.314 P.315 P.316
General Table

General Table
of Contents

of Contents
Mold Parts

Mold Parts
General Table of Contents 1

General Table of Contents 1

Guide bushings Precision guide bushings Guide bushings

Shoulder type Straight type Shoulder type Straight type Shoulder type Straight type Mold opening
Tension links Bolts/retainers for tension link PL Pullers
(no oil groove) (no oil groove) (With oil groove) (With oil groove) (With oil groove) (With oil groove) prevention plates
M-GBA M-GBB M-GBHF M-GBSF M-GBGF M-GBRF M-HLB M-PBB M-HRA M-HRB M-PLL□ M-OPB
P.286 P.287 P.288 P.289 P.290 P.291 P.317 P.318 P.320 P.321

Ejector,
space
parts

Guide bushing self lubricating, copperalloy type Support pins

Head type Head, press-Àt length desig- Head, press-Àt length designa- Support pin collars Mold opening Ejector guide pins
Straight type Support pin collars prevention plates
Product name
Retaining ring type JIS centering location type JIS stuck-out type
(With oil groove) nation type (no oil groove) tion type (with spiral oil groove) (for setting 5mm)
M-GBGDF M-GBRDF M-SPN M-SPHF M-SPHFS M-SPC M-SPD M-OPC Catalog No. M-EGA M-EGB M-EGC
P.292 P.293 P.294 P.295 P.296 P.297 P.321 Page P.326 P.327 P.328

Tapered Lock Pins -bolt PL Installation type- Tapered Lock Pins -basic type- Tapered Lock Pins Ejector guide bushings
Precision type Super precision type Precision type Super precision type Precision JIS type JIS type Linear motion bearing type Self lubricating, copper alloy type Self lubricating, heat-resisting type
M-TLC□ M-TLD□ M-TLG□ M-TLH□ M-TLB□ M-EBB M-EBD M-EBG M-EBC
P.298 P.299 P.300 P.330 P.331 P.332 P.333

254 255

5
 General Table of Contents
2-Plate Type S series
High rigidity type Standard type Large type
1515 ∼ 3040 1113 ∼ 7080 5585 ∼ 9010
Pages 24 to 77 Pages 78 to 259 Pages 264 to 283

3-Plate Type D & E series

High rigidity type Standard type
1518 ∼ 3040 1113 ∼ 5070
Pages 288 to 337 Pages 338 to 479

3-Plate Type F & G series 3-Plate Type H series

High rigidity type Standard type 2540 ∼ 4070
1515 ∼ 3040 1113 ∼ 5070
Pages 486 to 539 Pages 540 to 673 Pages 680 to 709

6
 Cassette Mold Bases
QMC series Sumitomo Cassette type series NISSEI FP SYSTEM

Pages 712 to 719 Pages 720 to 723 Pages 724 to 725

Cavity Retainer Sets

Cavity retainer set Cavity retainer set for die cast
1515 ∼ 6070 1518 ∼ 5065
Pages 730 to 757 Pages 764 to 785

●How to use catalogs See page 4

●Features of mold bases See page 8

●High rigidity type and standard type See page 10

●Specifications and selection of mold bases See page 12

●Technical data See page 787

●Customer guide See page 815

7
 Features of mold bases

Carefully selected materials used

Consistent quality
Extensive product variations
Low price & short delivery Pitch difference
This guide, which is installed with a different
pitch, prevents improper installation.
Backing plate
Backing plate is available in two thickness
dimensions according to injection pressures.

Threaded holes for eye bolts marks

Threaded holes for eye bolts are machined in Squareness datum planes are clearly
this direction and at the symmetrical position. marked with . As the planes are
simultaneously machined, there is no
datum plane deviation.

8
 Name Plate
Company name and the serial number are indicated.

Holes for ejector rods

Ejector rod holes are machined on
the bottom clamping plate.

Spacer type
A spacer type defined by eliminating counterbores
from ejector pins is also available.
Material
The material for mold plates, stripper plate and
runner plate can be changed to prehardened
steel and aluminum alloy.

High regidity type

Wider spacer blocks are also available
according to injection pressures applied.

9
 High Rigidity Type and Standard Type
CW EFW CW

RP

RPL
RP

F E
RPW

High rigidity type Standard type

Nominal Spacer Spacer
Ejector plate Return pin Ejector plate Return pin
dimension block block
CW EFW E F RP RPW RPL CW EFW E F RP RPW RPL
1515 114 114
1518 144 144
1520 38 70 13 15 12 28 164 28 90 13 15 12 48 164
1523 194 194
1525 214 214
1818 144 138
1820 164 158
1823 43 90 13 15 12 48 194 33 110 13 15 12 68 188
1825 214 208
1830 264 258
2020 164 13 15 12 84 150
2023 194 180
53 90 13 15 12 48 38 120
2025 214 15 20 15 80 200
2030 264 250
2323 188 180
2325 208 200
58 110 13 15 12 68 43 140 15 20 15 106
2330 258 250
2335 308 300
2525 200 200
15 110
2530 250 250
63 120 15 20 15 80 48 150 15 20
2535 300 298
20 102
2540 350 348
2730 250 240
68 130 15 20 15 90 53 160 15 20 20 114
2735 300 290
3030 250 240
3035 78 140 15 20 15 106 300 58 180 20 25 20 134 290
3040 350 340

10
■ Features of high rigidity type
① Adopts spacer blocks wider than the standard type to hold mold plates, which allows to reduce the deflection
of the mold plates. Therefore, the deflection of mold plates due to injection pressure is reduced.
② Standard type mold bases prevent the deflection of mold plates by increasing the thickness of mold plates
and backing plates. If the same amount of deflection as the standard type is allowed when using this type
of mold base, the thickness of the mold plates and backing plates can be reduced, making the mold more
compact.
③ As the return pins are located at the inner positions, the degree of freedom is increased in securing space for
machining channels for water and heater. Temperature control holes can be placed at the optimum places.

■ The range of sizes supported by high rigidity type

Series Size Type

Available in 27 sizes from 1515 to 3040
S series SA, SB, SC and SD types
(see left table)
Available in 25 sizes from 1518 to 3040 DA, DB, DC and DD types
D and E series
(excluding 1515 and 1818) (see left table) EA, EB, EC and ED types
Available in 27 sizes from 1515 to 3040 FA and FC types
F and G series
(see left table) GA and GC types

※ Calculation of the deflection of moving side mold plate ☞ P.794

Wider

High rigidity type Standard type

11
 Specifications and Selection of Mold Bases

Specification of clamping plate

Length of puller bolt

Specification of guide pin

Selection of
U
plate thickness

Specification of ejector plate

Length of support pin

■ Specification and selection of each series

2-plate type 3-plate type
Specification
S series D & E series F & G series H series
A dimension ○ ○ ○ ○
Selection of B dimension ○ ○ ○ ○
plate thickness U dimension ○ ○ ○ ○
C dimension ○ ○ ○ ○
Standard Specification of clamping plate ○ ○ ○ ○
specification Specification of guide ○ ○ ○
Specification of ejector plate ○ ○ ○ ○
Specification of support pin ○
Length of support pin ○ ○ ○
Length of puller bolt ○
Selection of R dimension ○ ○ ○
plate thickness S dimension ○ ○ ○ ○
Optional
Remove threaded holes for eye bolts ○ ○ ○ ○
specification
Remove a hole for ejector rod ○ ○ ○ ○
Material change specification ○ ○ ○
Standard specifications require specifying dimensions. Optional specifications are specified only when necessary.
The specifications marked with ○ are selectable.
12
1. Selection of plate thickness
For the thickness of cavity plate (fixed half) (A dimension), cavity plate (moving half) (B dimension) and backing plate
(U dimension), multiple dimensions are standardized. Please select the desired thickness for each plate.
A

A
B

B
U

U
C

■Selection of A dimension, B dimension and C dimension

Please select A, B and C dimension from the dimension table shown in each page.
(E.g.) 40 50 60 70 80 90
A DIMM 100 110 120 130 140 150

40 50 60 70 80 90
B DIMM 100 110 120 130 140 150

C DIMM 100 110 120 130

※If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers. E.g.: (100→ 10 )

■Selection of U dimension
For U dimension, please select V or W from the table shown in each page.
(E.g.) U DIMM
V 30
W 40
— Types without backing plate
※ If 30 is desired for U dimension, specify V and if 40 is preferred, specify 40.

13
 Specifications and Selection of Mold Bases
2. Specifications of clamping plate and guide
Depending on how the clamping plate is mounted on the molding machine and how the guide pins is installed, the
following four specifications are available. Please select one of them.
Depending on the mounting methods, the clamping plates are available in two types: clamping type, which is secured
with clamping tool, and bolt-fastening type, which is directly fixed with bolts. The guide pin can be installed either from
fixed or moving half of cavity plate.

■Code: S＊1 ■Code: X＊1

Clamping plate - clamping type Clamping plate - bolt-fastening type
Guide pin - installed in the cavity plate (moving half) Guide pin - installed in the cavity plate (moving half)

■Code: Y＊1 ■Code: Z＊1

Clamping plate - clamping type Clamping plate - bolt-fastening type
Guide pin - installed in the cavity plate (fixed half) Guide pin - installed in the cavity plate (fixed half)

＊1. Depending on the series or size, different code may be assigned. Please specify by using the codes shown in
each page (for nominal dimensions 4545, 4550, 4555 and 4560, different codes are assigned).
For F & G series 3-plate type mold bases, no guide pin option is available. Therefore, the available code for clamping type
clamping plate will be S only, and that for the bolt-fastening type will be X only.
14
3. Specification of ejector plate
Depending on how the ejector pin is assembled, the following two specifications are available. Please select one of them.

■Code: M (Standard type mold base) ■Code: L (Standard type mold base)
B (High rigidity type mold base) D (High rigidity type mold base)
Counterbore type Spacer type

■Regarding the use of spacer type

Spacer type refers to an installation method in which spacer rings are inserted to provide a clearance of 4 mm for installing
the ejector pin.

Spacer ring

 D
 d

+0.02
K 4 +0.01

Ejector pin
Return pin Nominal Applicable
D d K
dimension bolt
Ejector retainer plate 5 13 5.5 5 M5
Spacer ring 6 14 6.5 6 M6
Ejector base plate 8 18 8.5 6 M8
10 22 10.5 7 M10
12 24 12.5 9 M12

①To maintain the precision, we use the largest possible rings allowed for the effective space.
②To prevent interference of the return pin, a single head cutting of the pin is performed in advance.
15
 Specifications and Selection of Mold Bases
4. Specification of support pin
For D & E series 3-plate type mold bases, the following four specifications are available, depending on the positions to
install support pins and whether or not to use bushings.

■Code: OH ■Code: ON
Installs support pins at the outer positions Installs support pins at the outer positions
with bushings without bushings

Support pin Guide pin Support pin Guide pin

■Code: IH ■Code: IN
Installs support pins at the inner positions Installs support pins at the inner positions
with bushings without bushings

Guide pin Support pin Guide pin Support pin

16
5. Length of support pins and puller bolts
■Length of support pins
Select the length of support pins for 3-plate type mold bases from the dimension table shown in each page. The support
pin length is the full length as shown below.

■Length of puller bolts

For H series 3-plate type mold base, puller bolts M-PBA and M-PBC are used. The length of M-PBC is determined by the
size of mold base. Select the length of M-PBA from the dimension table shown in each table. The M-PBA length is the
length under the head.

● Length of support pins for each series ● Length of puller bolts

10
Puller bolt M-PBC
Length of support pin

Length of support pin

Length of support pin

Length of puller bolt

Puller bolt M-PBA

D & E series F & G series H series H series

■Adjustment of puller bolts

1. For the adjustment of opening amount between the top clamping plate and the runner plate, puller bolts of standard
length of 10 mm are used. If changing the opening amount, make an adjustment by inserting a washer or changing the
depth of counterbore, etc.
2. The opening amount between the runner plate and the cavity plate (fixed half) is determined by the length of puller bolt
M-PBA. If the length of M-PBA is not suitable, make an adjustment by creating a counterbore in the cavity plate (fixed
half).

17
 Specifications and Selection of Mold Bases
6. Optional specification
Optional specifications can be specified with simple codes to change a part of dimensions, processing or materials
used for the standard specifications. Unlike in the case of the standard specifications, specify optional specifications
only when necessary.

Remove threaded hole for eye bolt

Selection of
plate thickness
Material change spec.
S

Remove hole for ejector rod

Specification Description
The thickness of runner plate can be changed to the dimensions other than the
R dimension
Selection of standard plate thickness dimensions. For available thickness options, see each page.
plate thickness The thickness of stripper plate can be changed to the dimensions other than the
S dimension
standard plate thickness dimensions. For available thickness options, see each page.
Remove threaded holes Standard specification can be changed to a specification that does not include the
for eye bolts threaded holes for the standard eye bolts.
Standard specification can be changed to a specification that does not include the hole
Remove a hole for the ejector rod
for the standard ejector rod.
Materials of the mold plates and stripper plates can be changed to HPM1, NAK55,
Material change specification
NAK80 or AAS (aluminum alloy).
※ Available optional specifications may vary depending on the series and sizes, etc. For details, see each page.

18
How to Order Mold Bases
The specifications and dimensions available for selection are shown in each mold base page.
When ordering, please specify respective specifications and dimensions by using codes and figures in the table as
shown below.

E.g. D & E series 2530

■ How to order

■ Order example MDC DA 2530 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH positions with bushings
Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 90 100 Installs support pins at the inner
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit IH positions with bushings
numbers. e.g. (100→ 10 ) Installs support pins at the inner
※ When selecting DE or DF without Plate C, specify 00. IN positions without bushings

Width of clamping Orientation of

plate TW guide This may be changed to J or P by
Futaba if there is any addition or
S 300 change to the specification.

X 350
U DIMM Specification of ejector Plates
Y 300 V 35 M Counterbore type
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2530 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

※ If the runner plate (Plate R) gets thinner, the guide bushing also becomes shorter, and the length of the guide section is reduced.

※ Mold base specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing & Mold Parts Edition”for details.
We also accept orders with drawings supplied by customers.
19
20
 TWO-PLATE TYPE S-SERIES
2-Plate Type
S series
■Structure and Component Name ・・・・・・・・・・・・・・・・・・・・・・・ P. 22

■High Rigidity Type S Series

  1515∼1830 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P. 24∼ 43

  2020∼2540 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P. 44∼ 67
  2730∼3040 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P. 68∼ 77

■S Series

  1113∼1835 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P. 78∼107

  2020∼2340 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.108∼133

  2525∼2940 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.134∼161

  3030∼3560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.162∼197

  4040∼4560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.198∼217

  5050∼5580 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.218∼235

  6060∼6580 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.236∼253

  7070∼7080 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.254∼259

■S Series Material Change Option ・・・・・・・・・・・・・・・・・・・・・・・ P.260

 S Series Structure & Component Name

Hexagon socket
head cap screw Threaded hole for eye bolt

Guide pin & guide bushing

Hexagon socket
head cap screw

Hole for ejector rod

Return pin

T Top clamping plate

A Cavity plate (fixed half) GBA Guide bushing

S Stripper plate GBB Guide bushing

B Cavity plate (moving half) GPA Guide pin

U Backing plate RPN Return pin

C Spacer block

E Ejector retainer plate

F Ejector base plate

L Bottom clamping plate

This diagram shows SB type as a representative example.

22
 S series
2-Plate Type
SAType SDType
Stripper plate ejection type without backing
Ejector pin ejection type
plate

T T
A GBA A GBA
GPA S GBB

Structure and Component Name

B

U RPN B GPA

C C
RPN
E E
F F
L L

SBType SEType
Stripper plate ejection type, which is actuated
Stripper plate ejection type
by mold opening behavior

T T

A GBA A GBA
S GBB S GBB
B GPA B GPA

U RPN U

C
C
E
F
L L

SCType SFType
Ejector pin ejection type without backing Stripper plate ejection type, which is actuated
plate by mold opening behavior, without backing plate

T
T
A GBA
A GBA
S GBB
GPA
B B GPA

C RPN
C
E
F
L L

23
 High Rigidity Type
S Series 1515
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

34

57
114

132
150
56

55
12
Return pin

2 X 4-M10 28
16 52
Guide pin

4-M6 114 Datum plane

120

◆ High rigidity type

Standard type P.84
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

24
TD Technical Data P.787 STD Standard type P.84

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1515 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
5
C DIMM 50 60 70 1
Specification of ejector plate
5
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
U DIMM
Y 200 V 30
W 40
Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1515 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Specifications other than the above are also available.
Additional
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
change ※ Details ☞ P.260

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

25
 High Rigidity Type
S Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

34

72
162
180
144
86

70
12
Return pin

2 X 4-M10 28
16 52
Guide pin

4-M6 114 Datum plane

120

◆ High rigidity type

Standard type P.86
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

26
TD Technical Data P.787 STD Standard type P.86

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1518 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
5
C DIMM 50 60 70 1
Specification of ejector plate
8
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
U DIMM
Y 200 V 30
W 40
Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1518 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

27
 High Rigidity Type
S Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

82
34
106
164

182
200
80
12
Return pin

2 X 4-M10 28
16 52
Guide pin

4-M6 114 Datum plane

120

◆ High rigidity type

Standard type P.88
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

28
TD Technical Data P.787 STD Standard type P.88

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1520 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
5
C DIMM 50 60 70 2
Specification of ejector plate
0
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
U DIMM
Y 200 V 30
W 40
Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1520 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

29
 High Rigidity Type
S Series 1523
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

97
34

212
230
136
194

95
12
Return pin

2 X 4-M10 28
16 52
Guide pin

4-M6 114 Datum plane

120

◆ High rigidity type

Standard type P.90
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

30
TD Technical Data P.787 STD Standard type P.90

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1523 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
5
C DIMM 50 60 70 2
Specification of ejector plate
3
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
U DIMM
Y 200 V 30
W 40
Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1523 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

31
 High Rigidity Type
S Series 1525
Clamping plate spec. TW
Clamping type 200
TW Bolt-fastening type 230

150
38 70 38
M12

107
34
156

232
250
214

12
Return pin
105

2 X 4-M10 28
16 52
Guide pin

4-M6 114 Datum plane

120

◆ High rigidity type

Standard type P.92
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

32
TD Technical Data P.787 STD Standard type P.92

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1525 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
5
C DIMM 50 60 70 2
Specification of ejector plate
5
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 200 ※ The order method (code) of this part is
different from that of standard type.

X 230
U DIMM
Y 200 V 30
W 40
Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1525 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

33
 High Rigidity Type
S Series 1818
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

34

67
134
144

162
180
64

65
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6 134 Datum plane

145

◆ High rigidity type

Standard type P.96
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

34
TD Technical Data P.787 STD Standard type P.96

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1818 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
8
C DIMM 50 60 70 1
Specification of ejector plate
8
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 230 ※ The order method (code) of this part is
different from that of standard type.

X 280
U DIMM
Y 230 V 30
W 40
Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1818 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

35
 High Rigidity Type
S Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

77
34
154
164

182
200
84

75
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6 134 Datum plane

145

◆ High rigidity type

Standard type P.98
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

36
TD Technical Data P.787 STD Standard type P.98

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1820 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
8
C DIMM 50 60 70 2
Specification of ejector plate
0
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 230 ※ The order method (code) of this part is
different from that of standard type.

X 280
U DIMM
Y 230 V 30
W 40
Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1820 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

37
 High Rigidity Type
S Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

92
34
184

212
230
114
194

90
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6
134 Datum plane

145

◆ High rigidity type

Standard type P.100
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

38
TD Technical Data P.787 STD Standard type P.100

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1823 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
8
C DIMM 50 60 70 2
Specification of ejector plate
3
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 230 ※ The order method (code) of this part is
different from that of standard type.

X 280
U DIMM
Y 230 V 30
W 40
Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1823 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

39
 High Rigidity Type
S Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

102
34
204

232
250
124
214

100
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6
134 Datum plane

145

◆ High rigidity type

Standard type P.102
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

40
TD Technical Data P.787 STD Standard type P.102

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1825 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
8
C DIMM 50 60 70 2
Specification of ejector plate 5
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 230 ※ The order method (code) of this part is
different from that of standard type.

X 280
U DIMM
Y 230 V 30
W 40
Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1825 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

41
 High Rigidity Type
S Series 1830
Clamping plate spec. TW
Clamping type 230
TW Bolt-fastening type 280
180
43 90 43
M12

127
34
254
174
264

282
300
12 125
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6 134 Datum plane

145

◆ High rigidity type

Standard type P.104
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 15 A 20
B A 20

Plate S
U
U

13
13
C

15
15

20
20

42
TD Technical Data P.787 STD Standard type P.104

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1830 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.
1
8
C DIMM 50 60 70 3
Specification of ejector plate
0
Width of clamping Orientation of B Counterbore type
plate TW guide
D Spacer type
S 230 ※ The order method (code) of this part is
different from that of standard type.

X 280
U DIMM
Y 230 V 30
W 40
Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1830 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 15 A 20
A 20

Plate S
B

13

13
C

C
15

15
20

20

43
 High Rigidity Type
S Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

34

77
154
164

182
200
80

75
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6 154 Datum plane

160

◆ High rigidity type

Standard type P.108
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

44
TD Technical Data P.787 STD Standard type P.108

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2020 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80 90 100
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.
2
0
C DIMM 50 60 70 80 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 250 different from that of standard type.

X 280 U DIMM
V 30
Y 250
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2020 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

45
 High Rigidity Type
S Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

34

92
194
184
110

212
230
90
12
Return pin

2 X 4-M12 48
20 72
Guide pin

4-M6
154 Datum plane

160

◆ High rigidity type

Standard type P.110
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

46
TD Technical Data P.787 STD Standard type P.110

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2023 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80 90 100
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.
2
0
C DIMM 50 60 70 80 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 3
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 250 different from that of standard type.

X 280 U DIMM
V 30
Y 250
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2023 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

47
 High Rigidity Type
S Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

102
34
130
204
214

232
250
100
12
Return pin

2 X 4-M12 48
20 72
Guide pin
154 Datum plane
4-M6
160

◆ High rigidity type

Standard type P.112
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

48
TD Technical Data P.787 STD Standard type P.112

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2025 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80 90 100
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.
2
0
C DIMM 50 60 70 80 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 250 different from that of standard type.

X 280 U DIMM
V 30
Y 250
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2025 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

49
 High Rigidity Type
S Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

127
34
264
254
180

282
300
12 125
Return pin

2 X 6-M12 48
20 72
Guide pin
154 Datum plane
4-M6
160

◆ High rigidity type

Standard type P.114
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

50
TD Technical Data P.787 STD Standard type P.114

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2030 30 30 60 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

20 25 30 35 40 50
A DIMM 60 70 80 90 100
This may be changed to J or P by
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.
2
0
C DIMM 50 60 70 80 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 250 different from that of standard type.

X 280 U DIMM
V 30
Y 250
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2030 40 30 50 S V B N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

51
 High Rigidity Type
S Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

34

92
106
184
188

210
230
90
12
Return pin

2 X 4-M12 68
20 90
Guide pin

4-M8 184 Datum plane

185

◆ High rigidity type

Standard type P.122
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

52
TD Technical Data P.787 STD Standard type P.122

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2323 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.
2
3
C DIMM 60 70 80 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 3
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 280 different from that of standard type.

X 350 U DIMM
V 35
Y 280
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2323 50 40 60 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

53
 High Rigidity Type
S Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

102
34
126
204
208

230
250
100
12
Return pin

2 X 4-M12 68
20 90
Guide pin

4-M8 184 Datum plane

185

◆ High rigidity type

Standard type P.124
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

54
TD Technical Data P.787 STD Standard type P.124

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2325 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.
2
3
C DIMM 60 70 80 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 280 different from that of standard type.

X 350 U DIMM
V 35
Y 280
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2325 50 40 60 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

55
 High Rigidity Type
S Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

127
34
258
254
174

280
300
125
12
Return pin

2 X 4-M14 68
20 90
Guide pin

4-M8 184 Datum plane

185

◆ High rigidity type

Standard type P.128
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

56
TD Technical Data P.787 STD Standard type P.128

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2330 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.
2
3
C DIMM 60 70 80 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 280 different from that of standard type.

X 350 U DIMM
V 35
Y 280
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2330 50 40 60 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

57
 High Rigidity Type
S Series 2335
B DIMM FK 取付板の仕様
Clamping plate spec. TW
40 or less Ｍ12 クランプ式
Clamping type 200
280
50 or more Ｍ16 ボルト締式type
Bolt-fastening 230
350

TW
230
58 110 58
FK

152
34
224
304

330
350
308

150
12
Return pin

2 X 6-M14 68
20 90
Guide pin

4-M8 184 Datum plane

185

◆ High rigidity type

Standard type P.130
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 20 A 25
B A 25

Plate S
U
U

13
13
C

15
15

25
25

58
TD Technical Data P.787 STD Standard type P.130

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2335 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.
2
3
C DIMM 60 70 80 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 280 different from that of standard type.

X 350 U DIMM
V 35
Y 280
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2335 50 40 60 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 20 A 25
A 25

Plate S
B

13

13
C

C
15

15
25
25

59
 High Rigidity Type
S Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

34

97
108

250
194
200

230
95
15
Return pin

2 X 4-M14 80
25 100
Guide pin

4-M8 194 Datum plane

200

◆ High rigidity type

Standard type P.134
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

60
TD Technical Data P.787 STD Standard type P.134

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2525 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100 110 120
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.
2
5
C DIMM 60 70 80 90 2
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 300 different from that of standard type.

X 350 U DIMM
V 35
Y 300
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2525 50 40 70 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

61
 High Rigidity Type
S Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

122
34
250
244
154

280
300
120
15
Return pin

2 X 4-M14 80
25 100
Guide pin

4-M8 194 Datum plane

200

◆ High rigidity type

Standard type P.138
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

62
TD Technical Data P.787 STD Standard type P.138

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2530 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100 110 120
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.
2
5
C DIMM 60 70 80 90 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 300 different from that of standard type.

X 350 U DIMM
V 35
Y 300
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2530 50 40 70 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

63
 High Rigidity Type
S Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
63 120 63
M16

147
34
300
294
204

330
350
15
Return pin
145

2 X 6-M14 80
25 100
Guide pin

4-M8 194 Datum plane

200

◆ High rigidity type

Standard type P.140
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

64
TD Technical Data P.787 STD Standard type P.140

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2535 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100 110 120
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.
2
5
C DIMM 60 70 80 90 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 300 different from that of standard type.

X 350 U DIMM
V 35
Y 300
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2535 50 40 70 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

65
 High Rigidity Type
S Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
63 120 63
M16

172
34
350
344
254

380
400
170
15
Return pin

2 X 6-M14 80
25 100
Guide pin

4-M8 194 Datum plane

200

◆ High rigidity type

Standard type P.142
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

66
TD Technical Data P.787 STD Standard type P.142

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2540 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

25 30 35 40 50 60
A DIMM 70 80 90 100 110 120
This may be changed to J or P by
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.
2
5
C DIMM 60 70 80 90 4
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 300 different from that of standard type.

X 350 U DIMM
V 35
Y 300
W 50

Z 350 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2540 50 40 70 S V B N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

67
 High Rigidity Type
S Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

122
250
244
154

280
300
φ15

120
Return pin

2 X 4-M14 90
φ25 110
Guide pin

4-M8 214 Datum plane

215

◆ High rigidity type

Standard type P.148
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

68
TD Technical Data P.787 STD Standard type P.148

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2730 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

30 35 40 50 60 70
A DIMM 80 90 100 110 120
This may be changed to J or P by
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.
2
7
C DIMM 70 80 90 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 320 different from that of standard type.

X 400 U DIMM
V 40
Y 320
W 50

Z 400 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2730 50 40 70 S V B N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

69
 High Rigidity Type
S Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

147
300
294
204

330
350
φ15

145
Return pin

2 X 6-M14 90
φ25 110
Guide pin

4-M8 214 Datum plane

215

◆ High rigidity type

Standard type P.150
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 25 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

70
TD Technical Data P.787 STD Standard type P.150

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2735 40 40 70 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

30 35 40 50 60 70
A DIMM 80 90 100 110 120
This may be changed to J or P by
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.
2
7
C DIMM 70 80 90 3
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 320 different from that of standard type.

X 400 U DIMM
V 40
Y 320
W 50

Z 400 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 2735 50 40 70 S V B N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 25 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

71
 High Rigidity Type
S Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

117
250
234
138

280
300
φ15

115
Return pin

2 X 4-M14 106
φ30 120
Guide pin
Datum plane
4-M8 234
240

◆ High rigidity type

Standard type P.162
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 30 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

72
TD Technical Data P.787 STD Standard type P.162

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3030 50 50 80 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

30 35 40 50 60 70
A DIMM 80 90 100 110 120 130
This may be changed to J or P by
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 130 change to the specification.
3
0
C DIMM 70 80 90 100 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 350 different from that of standard type.

X 400 U DIMM
V 45
Y 350
W 60

Z 400 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 3030 50 60 70 S V B N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 30 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

73
 High Rigidity Type
S Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

142
300
284
188

330
350
φ15

140
Return pin

2 X 6-M14 106
φ30 120
Guide pin
Datum plane
4-M8 234
240

◆ High rigidity type

Standard type P.166
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 30 A 25
B A 25

Plate S
U

15
15
C

20
20

25
25

74
TD Technical Data P.787 STD Standard type P.166

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3035 50 50 80 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

35 40 50 60 70 80
A DIMM 90 100 110 120 130
This may be changed to J or P by
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.
3
0
C DIMM 70 80 90 100 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 5
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 350 different from that of standard type.

X 400 U DIMM
V 45
Y 350
W 60

Z 400 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 3035 50 60 70 S V B N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 30 A 25
A 25

Plate S
B

15

15
C

C
20

20
25
25

75
 High Rigidity Type
S Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M20

167
350
334
238

380
400
φ15

165
Return pin

2 X 6-M14 106
φ30 120
Guide pin
Datum plane
4-M8 234
240

◆ High rigidity type

Standard type P.168
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype
B 30 A 30
B A 30

Plate S
U

15
15
C

20
20

30
30

76
TD Technical Data P.787 STD Standard type P.168

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3040 50 50 80 S V B N Option

Type SA SB SC SD

High Rigidity type

Nominal Dimension

35 40 50 60 70 80
A DIMM 90 100 110 120 130
This may be changed to J or P by
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.
3
0
C DIMM 70 80 90 100 4
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate 0
Width of clamping Orientation of
B Counterbore type

plate TW guide D Spacer type

※ The order method (code) of this part is
S 350 different from that of standard type.

X 400 U DIMM
V 45
Y 350
W 60

Z 400 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 3040 50 60 70 S V B N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SCtype SDtype
B 30 A 30
A 30

Plate S
B

15

15
C

C
20

20
30
30

77
 S Series 1113

175
110
24 60 24

24

51
102

108
130
88
66

49
10
Return pin

2 X 4-M8 30
12 46 Datum plane
Guide pin

4-M5 82
90

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 10 A 15
B A 15

A 15

Plate S
B
U

13
13

13
C

C
13
13

13
15

15

15

78
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1113 25 25 50 X V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
1
A DIMM 60
20 25 30 35 40 50 1
This may be changed to J or P by
3
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 change to the specification.

C DIMM 40 50
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Orientation of
M Counterbore type

guide L Spacer type

— When selecting SE or SF type

X
U DIMM
V 25
W 30
Z
— Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1113 30 25 40 X V M N / S20 / #EH

Code Description Code Description

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 10 A 15

B 10 A 15
B 10 A 15

Plate S
Plate S Plate S
U
13

C
C

13

15
15

15

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
79
 S Series 1313

175
130
24 80 24

51
24
102

108
130
88
66

49
10
Return pin

2 X 4-M8 48
12 66 Datum plane
Guide pin

4-M5 102
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 10 A 15
B A 15

A 15

Plate S
B
U

13
13

13
C

C
13
13

13
15

15

15

80
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1313 25 25 50 X V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
3
A DIMM 60
20 25 30 35 40 50
1
This may be changed to J or P by
3
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 change to the specification.

C DIMM 40 50
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Orientation of
M Counterbore type

guide L Spacer type

— When selecting SE or SF type

X
U DIMM
V 25
W 30
Z
— Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1313 30 25 40 X V M N / S20 / #EH

Code Description Code Description

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 10 A 15

B 10 A 15
B 10 A 15

Plate S
Plate S Plate S
U
13

C
C

13

15
15

15

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
81
 S Series 1315

175
130
24 80 24

61
24
122
108

128
150
86

59
10
Return pin

2 X 4-M8 48
Datum plane
12 66
Guide pin

4-M5 102
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 10 A 15
B A 15

A 15

Plate S
B
U

13
13

13
C

C
13
13

13
15

15

15

82
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1315 25 25 50 X V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
3
A DIMM 60
20 25 30 35 40 50
1
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 change to the specification.

C DIMM 40 50
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Orientation of
M Counterbore type

guide L Spacer type

— When selecting SE or SF type

X
U DIMM
V 25
W 30
Z
— Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1315 30 25 40 X V M N / S20 / #EH

Code Description Code Description

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 10 A 15

B 10 A 15
B 10 A 15

Plate S
Plate S Plate S
U
13

C
C

13

15
15

15

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
83
 S Series 1515
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

34

57
114

132
150
56

12

55
Return pin

2 X 4-M10 48
16 72
Guide pin
Datum plane
4-M6 114
120

High Rigidity type P.24

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

84
TD Technical Data P.787 HR High Rigidity type P.24

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1515 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
1
This may be changed to J or P by
5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1515 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
85
 S Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

72
34
144

162
180
86

70
12
Return pin

2 X 4-M10 48
16 72 Datum plane
Guide pin

4-M6 114
120

High Rigidity type P.26

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

86
TD Technical Data P.787 HR High Rigidity type P.26

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1518 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
1
This may be changed to J or P by
8
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1518 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
87
 S Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

82
34
164
106

182
200
80
12
Return pin

2 X 4-M10 48
16 72
Guide pin
114 Datum plane
4-M6
120

High Rigidity type P.28

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

88
TD Technical Data P.787 HR High Rigidity type P.28

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1520 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1520 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
89
 S Series 1523
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

97
34
194
136

212
230
12 95
Return pin

2 X 4-M10 48
16 72 Datum plane
Guide pin

4-M6 114
120

High Rigidity type P.30

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

90
TD Technical Data P.787 HR High Rigidity type P.30

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1523 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 3
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1523 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
91
 S Series 1525
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

107
34
214
156

232
250
105
12
Return pin

2 X 4-M10 48
16 72
Guide pin
114 Datum plane
4-M6
120
High Rigidity type P.32
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

92
TD Technical Data P.787 HR High Rigidity type P.32

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1525 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1525 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
93
 S Series 1530
TW Clamping plate spec. TW
Clamping type 200
150 Bolt-fastening type 230
28 90 28
M12

132
34
264
206

282
300
130
12
Return pin

2 X 4-M10 48
16 72 Datum plane
Guide pin

4-M6 114
120
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

94
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1530 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
5
A DIMM 60 70 80
20 25 30 35 40 50
3
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 200

X 230 U DIMM
V 30
Y 200
W 40

Z 230 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1530 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
95
 S Series 1818
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

34

67
138
134

160
180
64

12

65
Return pin

2 X 4-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145

High Rigidity type P.34

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

96
TD Technical Data P.787 HR High Rigidity type P.34

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1818 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
1
This may be changed to J or P by 8
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1818 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
97
 S Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

77
34
158
154

180
200
84

75
12
Return pin

2 X 4-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145

High Rigidity type P.36

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

98
TD Technical Data P.787 HR High Rigidity type P.36

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1820 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1820 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
99
 S Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

92
34
188
184
114

210
230
90
12
Return pin

2 X 4-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145

High Rigidity type P.38

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

100
TD Technical Data P.787 HR High Rigidity type P.38

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1823 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 3
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1823 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
101
 S Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

102
34
208
204
124

230
250
12
Return pin
100

2 X 4-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145

High Rigidity type P.40

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

102
TD Technical Data P.787 HR High Rigidity type P.40

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1825 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
2
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1825 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
103
 S Series 1830
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280
TW
180
33 110 33
M12

127
34
258
254
174

280
300
125
12
Return pin

2 X 4-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145
High Rigidity type P.42
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

104
TD Technical Data P.787 HR High Rigidity type P.42

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1830 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
3
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1830 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
105
 S Series 1835
TW Clamping plate spec. TW
Clamping type 230
180 Bolt-fastening type 280
33 110 33
M12

152
34
224
308
304

330
350
150
12
Return pin

2 X 6-M12 68
20 90 Datum plane
Guide pin

4-M8 134
145
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 15 A 20
B A 20

A 20

Plate S
B
U

13
13
13

C
C

15
15
15
20

20

20

106
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 1835 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 1
8
A DIMM 60 70 80
20 25 30 35 40 50
3
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 change to the specification.

C DIMM 50 60 70 80
※ When selecting SE or SF without Plate C, specify 00.
Specification of ejector plate

Width of clamping Orientation of

M Counterbore type

plate TW guide L Spacer type

— When selecting SE or SF type
S 230

X 280 U DIMM
V 30
Y 230
W 40

Z 280 — Types without backing plate

■ How to order optional specification

■ Order example MDC SB 1835 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 15 A 20

B 15 A 20
B 15 A 20

Plate S
Plate S Plate S
U
13

C
C

C
15

20
20
20

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
107
 S Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

34

77
154
150

180
200
80

12

75
Return pin

2 X 4-M12 84
20 100
Guide pin
Datum plane
4-M8 154
160

High Rigidity type P.44

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

13
13
13

C
C

15
15
15
25

25

25

108
TD Technical Data P.787 HR High Rigidity type P.44

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2020 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 2
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2020 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
13

C
C

C
15

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
109
 S Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

92
34
184
180
110

210
230
15

90
Return pin

2 X 4-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160

High Rigidity type P.46

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

110
TD Technical Data P.787 HR High Rigidity type P.46

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2023 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 2
This may be changed to J or P by 3
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2023 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
111
 S Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

102
34
204
200
130

230
250
100
15
Return pin

2 X 4-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160

High Rigidity type P.48

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

112
TD Technical Data P.787 HR High Rigidity type P.48

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2025 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 2
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2025 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
113
 S Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

127
34
254
250
180

280
300
15
Return pin
125

2 X 6-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160

High Rigidity type P.50

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

114
TD Technical Data P.787 HR High Rigidity type P.50

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2030 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 3
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2030 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
115
 S Series 2035
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

152
34
304
300
230

330
350
150
15
Return pin

2 X 6-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

116
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2035 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 3
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2035 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
117
 S Series 2040
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 250
50 or more Ｍ16 Bolt-fastening type 280
TW
200
38 120 38
FK

177
34
354
350
280

380
400
175

15
Return pin

2 X 6-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

118
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2040 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 4
This may be changed to J or P by 0
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2040 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
119
 S Series 2045
B DIMM FK TW Clamping plate spec. TW
40 or less Ｍ12 Clamping type 250
50 or more Ｍ16 200 Bolt-fastening type 280

38 120 38
FK

202
34
404
400
330

430
450
200

15
Return pin

2 X 6-M12 80
20 100
Guide pin
Datum plane
4-M8 154
160
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

120
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2045 30 30 60 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
0
20 25 30 35 40 50
A DIMM 60 70 80 90 100 4
This may be changed to J or P by 5
20 25 30 35 40 50 Futaba if there is any addition or
B DIMM 60 70 80 90 100 change to the specification.

C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 250

X 280 U DIMM
V 30
Y 250 W 40
— Types without backing plate
Z 280

■ How to order optional specification

■ Order example MDC SB 2045 40 30 50 S V M N / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
121
 S Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

92
34
184
180
106

230
210
15

90
Return pin

2 X 4-M12 106
20 120
Guide pin Datum plane
4-M8 184
185

High Rigidity type P.52

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

122
TD Technical Data P.787 HR High Rigidity type P.52

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2323 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
2
This may be changed to J or P by 3
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2323 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
123
 S Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

102
34
204
200
126

230
250
15

100
Return pin

2 X 4-M12 106
20 120
Guide pin Datum plane
4-M8 184
185

High Rigidity type P.54

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

124
TD Technical Data P.787 HR High Rigidity type P.54

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2325 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
2
This may be changed to J or P by 5
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2325 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
125
 S Series 2327
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

112
34
224
220
144

250
270
110
15
Return pin

2 X 4-M14 106
20 120
Guide pin
Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

126
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2327 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
2
This may be changed to J or P by 7
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2327 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
127
 S Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

127
34
254
250
174

280
300
125
15
Return pin

2 X 4-M14 106
20 120
Guide pin Datum plane
4-M8 184
185

High Rigidity type P.56

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

128
TD Technical Data P.787 HR High Rigidity type P.56

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2330 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
3
This may be changed to J or P by 0
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2330 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
129
 S Series 2335
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

152
34
304
300
224

330
350
15 150
Return pin

2 X 6-M14 106
20 120
Guide pin Datum plane
4-M8 184
185

High Rigidity type P.58

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

130
TD Technical Data P.787 HR High Rigidity type P.58

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2335 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
3
This may be changed to J or P by 5
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2335 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
131
 S Series 2340
Clamping plate spec. TW
Clamping type 280
TW Bolt-fastening type 350

230
43 140 43
M16

177
34
354
350
274

380
400
175
15
Return pin

2 X 6-M14 106
20 120
Guide pin Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 20 A 25
B A 25

A 25

Plate S
B
U

15
15
15
C

20
20
20
25

25

25

132
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2340 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
3
A DIMM 70 80 90 100
25 30 35 40 50 60
4
This may be changed to J or P by 0
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 280

X 350 U DIMM
V 35
Y 280 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2340 50 40 60 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 20 A 25

B 20 A 25
B 20 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
133
 S Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

34

97
200
194
108

230
250
15

95
Return pin

2 X 4-M14 110
25 130
Guide pin
Datum plane
4-M8 194
200

High Rigidity type P.60

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

134
TD Technical Data P.787 HR High Rigidity type P.60

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2525 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 2
This may be changed to J or P by 5
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2525 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
135
 S Series 2527
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

107
34
220
214
128

250
270
105
15
Return pin

2 X 4-M14 110
25 130
Guide pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

136
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2527 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 2
This may be changed to J or P by 7
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2527 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
137
 S Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

122
34
250
244
154

280
300
15
Return pin
120

2 X 4-M14 110
25 130
Guide pin
Datum plane
4-M8 194
200

High Rigidity type P.62

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

138
TD Technical Data P.787 HR High Rigidity type P.62

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2530 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 3
This may be changed to J or P by 0
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2530 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
139
 S Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
48 150 48
M16

147
34
298
294
204

330
350
20
Return pin
145

2 X 6-M14 102
25 130
Guide pin
Datum plane
4-M8 194
200

High Rigidity type P.64

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

140
TD Technical Data P.787 HR High Rigidity type P.64

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2535 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 3
This may be changed to J or P by 5
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2535 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate A, S or B. See the separate volume“Additional Mold Base
change ※ Details ☞ P.260 processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
141
 S Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
48 150 48
M16

172
34
348
344
254

380
400
170
20
Return pin

2 X 6-M14 102
25 130
Guide pin
Datum plane
4-M8 194
200

High Rigidity type P.66

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

142
TD Technical Data P.787 HR High Rigidity type P.66

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2540 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 4
This may be changed to J or P by 0
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2540 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
143
 S Series 2545
Clamping plate spec. TW
Clamping type 300
TW Bolt-fastening type 350

250
48 150 48
M16

197
34

430
450
398
394
304

195
20
Return pin

2 X 6-M14 102
25 130
Guide pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

144
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■注文例 MDC SA 2545 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 4
This may be changed to J or P by 5
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2545 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
145
 S Series 2550
Clamping plate spec. TW
TW Clamping type 300
250 Bolt-fastening type 350

48 150 48
M16

222
34
448
444
354

480
500
220

20
Return pin

2 X 6-M14 102
25 130
Guide pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U

15

15
15

C
C

C
20

20
20
25

25

25

146
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2550 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
5
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 5
This may be changed to J or P by 0
25 30 35 40 50 60 Futaba if there is any addition or
B DIMM 70 80 90 100 110 120 change to the specification.

C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 300

X 350 U DIMM
V 35
Y 300 W 50
— Types without backing plate
Z 350

■ How to order optional specification

■ Order example MDC SB 2550 50 40 70 S V M N / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C

C
20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For SE & SF type, ejector rod hole will not be machined.
147
 S Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

122
244
240
154

276
300
120
20
Return pin

2 X 4-M14 114
25 136
Guide pin
Datum plane
4-M10 214
215

High Rigidity type P.68

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

15

15

15
C
C

C
20

20

20
25

25

25

148
TD Technical Data P.787 HR High Rigidity type P.68

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2730 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
7
30 35 40 50 60 70
A DIMM 80 90 100 110 120 3
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 320

X 400 U DIMM
V 40
Y 320 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2730 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
149
 S Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

147
294
290
204

326
350
145
20
Return pin

2 X 6-M14 114
25 136
Guide pin
Datum plane
4-M10 214
215

High Rigidity type P.70

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

15

15

15
C
C

C
20

20

20
25

25

25

150
TD Technical Data P.787 HR High Rigidity type P.70

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2735 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
7
30 35 40 50 60 70
A DIMM 80 90 100 110 120 3
This may be changed to J or P by 5
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 320

X 400 U DIMM
V 40
Y 320 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2735 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
151
 S Series 2740
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

172
344
340
254

376
400
20
Return pin 170

2 X 6-M14 114
25 136
Guide pin
Datum plane
4-M10 214
215

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

15

15

15
C
C

C
20

20

20
25

25

25

152
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2740 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
7
30 35 40 50 60 70
A DIMM 80 90 100 110 120 4
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 320

X 400 U DIMM
V 40
Y 320 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2740 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
153
 S Series 2750
B DIMM FK Clamping plate spec. TW
70 or less Ｍ16
TW Clamping type 320
80 or more Ｍ20 270 Bolt-fastening type 400

53 160 53
FK

222
444
440
354

476
500
220
20
Return pin

2 X 6-M14 114
25 136
Guide pin
Datum plane
4-M10 214
215

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

15

15

15
C
C

C
20

20

20
25

25

25

154
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2750 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
7
30 35 40 50 60 70
A DIMM 80 90 100 110 120 5
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 320

X 400 U DIMM
V 40
Y 320 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2750 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
15

C
C
C

20

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
155
 S Series 2930
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

122
276
300
244
240
154

120
20
Return pin

2 X 4-M14 134
25 156 Datum plane
Guide pin

4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

20

20

20
C
C

C
25

25

25
25

25

25

156
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2930 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
9
30 35 40 50 60 70
A DIMM 80 90 100 110 120 3
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 40
Y 350 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2930 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
157
 S Series 2935
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

147
294
290
204

326
350
145
20
Return pin

2 X 6-M14 134
25 156 Datum plane
Guide pin

4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

20

20

20
C
C

C
25

25

25
25

25

25

158
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2935 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
9
30 35 40 50 60 70
A DIMM 80 90 100 110 120 3
This may be changed to J or P by 5
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 40
Y 350 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2935 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
159
 S Series 2940
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400
TW
290
53 180 53
M16

172
344
340
254

376
400
170
20
Return pin

2 X 6-M14 134
25 156 Datum plane
Guide pin

4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 25 A 25
B A 25

A 25

Plate S
B
U
U

20

20

20
C
C

C
25

25

25
25

25

25

160
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 2940 40 40 70 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 2
9
30 35 40 50 60 70
A DIMM 80 90 100 110 120 4
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 change to the specification.

C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 40
Y 350 W 50
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 2940 50 40 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 25 A 25

B 25 A 25
B 25 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
161
 S Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

117
240
234
138

276
300
115
20
Return pin

2 X 4-M14 134
30 156
Guide pin
Datum plane
4-M10 234
240

High Rigidity type P.72

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 25
A 25

A 25

Plate S
B

B
U

U
20

20

20
C
C
C

25

25

25
25

25

25

162
TD Technical Data P.787 HR High Rigidity type P.72

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3030 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
30 35 40 50 60 70
A DIMM 80 90 100 110 120 130 3
This may be changed to J or P by 0
30 35 40 50 60 70 Futaba if there is any addition or
B DIMM 80 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3030 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material AChanges the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 25

B 30 A 25
B 30 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
163
 S Series 3032
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

127
296
320
260
254
158

125
20
Return pin

2 X 4-M14 134
30 156
Guide pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 25
A 25

A 25

Plate S
B

B
U

U
20

20

20
C
C
C

25

25

25
25

25

25

164
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3032 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 3
This may be changed to J or P by 2
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3032 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 25

B 30 A 25
B 30 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
165
 S Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

142
326
350
290
284
188

140
20
Return pin

2 X 6-M14 134
30 156
Guide pin
Datum plane
4-M10 234
240

High Rigidity type P.74

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 25
A 25

A 25

Plate S
B

B
U

U
20

20

20
C
C
C

25

25

25
25

25

25

166
TD Technical Data P.787 HR High Rigidity type P.74

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3035 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 3
This may be changed to J or P by 5
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3035 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 25

B 30 A 25
B 30 A 25

Plate S
Plate S Plate S
U
20

C
C
C

25

25
25
25

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
167
 S Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M20

167
376
400
340
334
238

20
Return pin
165

2 X 6-M14 134
30 156
Guide pin
Datum plane
4-M10 234
240

High Rigidity type P.76

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

168
TD Technical Data P.787 HR High Rigidity type P.76

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3040 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 4
This may be changed to J or P by 0
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3040 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
169
 S Series 3045
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M20

192
426
450
390
384
288

25 190
Return pin

2 X 6-M16 128
30 156
Guide pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

170
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3045 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 4
This may be changed to J or P by 5
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3045 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
171
 S Series 3050
Clamping plate spec. TW
Clamping type 350
TW Bolt-fastening type 400

300
58 180 58
M20

217
440
434
338

476
500
215
25
Return pin

2 X 6-M16 128
30 156
Guide pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

172
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3050 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 5
This may be changed to J or P by 0
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3050 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
173
 S Series 3055
Clamping plate spec. TW
TW Clamping type 350
Bolt-fastening type 400
300
58 180 58
M24

242
490

388

526
550
484

240

25
Return pin

2 X 6-M16 128
30 156
Guide pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

174
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3055 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 5
This may be changed to J or P by 5
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3055 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
175
 S Series 3060
TW Clamping plate spec. TW
300 Clamping type 350
Bolt-fastening type 400
58 180 58
M24

267
576
600
540
534
438

265

25
Return pin

2 X 6-M16 128
30 156
Guide pin
Datum plane
4-M10 234
240
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

176
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3060 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
0
35 40 50 60 70 80
A DIMM 90 100 110 120 130 6
This may be changed to J or P by 0
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 350

X 400 U DIMM
V 45
Y 350 W 60
— Types without backing plate
Z 400

■ How to order optional specification

■ Order example MDC SB 3060 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
177
 S Series 3335
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

142
290
284
188

326
350
140
25
Return pin

2 X 6-M14 154
30 186
Guide pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

178
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3335 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
3
35 40 50 60 70 80
A DIMM 90 100 110 120 130 3
This may be changed to J or P by 5
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3335 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
179
 S Series 3340
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

167
340
334
238

376
400
165
25
Return pin

2 X 6-M14 154
30 186
Guide pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

180
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3340 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
3
35 40 50 60 70 80
A DIMM 90 100 110 120 130 4
This may be changed to J or P by 0
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3340 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
181
 S Series 3345
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

192
426
450
390
384
288

190
25
Return pin

2 X 6-M16 154
30 186
Guide pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

182
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3345 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
3
35 40 50 60 70 80
A DIMM 90 100 110 120 130 4
This may be changed to J or P by 5
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3345 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
183
 S Series 3350
Clamping plate spec. TW
Clamping type 400
TW Bolt-fastening type 550

330
58 210 58
M24

217
476
500
440
434
338

25
Return pin
215

2 X 6-M16 154
30 186
Guide pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 30 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

184
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3350 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
3
35 40 50 60 70 80
A DIMM 90 100 110 120 130 5
This may be changed to J or P by 0
35 40 50 60 70 80 Futaba if there is any addition or
B DIMM 90 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3350 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 30 A 30

B 30 A 30
B 30 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
185
 S Series 3535
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

142
326
350
290
284
178

140
25
Return pin

2 X 4-M16 164
30 196
Guide pin
Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

186
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3535 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 3
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3535 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
187
 S Series 3540
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

167
376
400
340
334
224

165
25
Return pin

2 X 6-M16 164
30 196
Guide pin
Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

188
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3540 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 4
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3540 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Material Changes the material of Plate A, S or B.
change ※ Details ☞ P.260 Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
189
 S Series 3545
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M24

192
390
384
274

426
450
190
25
Return pin

2 X 6-M16 164
30 196
Guide pin
Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

190
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3545 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 4
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3545 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
191
 S Series 3550
Clamping plate spec. TW
Clamping type 400
TW Bolt-fastening type 550

350
63 220 63
M24

212
440
424
308

476
500
210
25
Return pin

2 X 6-M16 152
35 196
Guide pin
Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

192
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3550 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 5
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3550 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
193
 S Series 3555
Clamping plate spec. TW
TW Clamping type 400
Bolt-fastening type 550
350
63 220 63
M24

237
490
474
358

526
550
235
25
Return pin

2 X 6-M16 152
35 196
Guide pin
Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

194
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3555 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 5
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3555 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
195
 S Series 3560
TW Clamping plate spec. TW
350 Clamping type 400
Bolt-fastening type 550
63 220 63
M24

262
576
600
540
524
408

260
25
Return pin

2 X 6-M16 152
35 196
Guide pin
Datum plane
4-M10 274
285
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

U
20

20

20
C

C
C
25

25

25
30

30

30

196
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 3560 50 50 80 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 3
5
40 50 60 70 80 90
A DIMM 100 110 120 130 6
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 change to the specification.

C DIMM 70 80 90 100 110

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 400

X 550 U DIMM
V 45
Y 400 W 60
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 3560 50 60 70 S V M N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
20

C
C
C

25

30
30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
197
 S Series 4040
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

162
340
324
208

374
400
160
25
Return pin

2 X 6-M16 198
35 234
Guide pin

4-M12 324 Datum plane

330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 30
B A 30

A 30

Plate S
B
U

25

25
25

C
C

30

30
30
30

30

30

198
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4040 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 4
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4040 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A Plate S Thickness Changes the Plate S thickness 35 to 40 , 50 or 60
Changes the material of Plate A, S or B.
#FB Removes the threaded holes for eye bolts for Plate B Material change
※ Details ☞ P.260

Removes the threaded holes for eye bolts Additional Specifications other than the above are also available.
#FK for Plate A and B processing
See the separate volume“Additional Mold Base Processing &
Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 30

B 35 A 30
B 35 A 30

Plate S
Plate S Plate S
U
25

C
C
C

30

30

30
30

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
199
 S Series 4045
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

187
390
374
254

424
450
185
25
Return pin

2 X 6-M16 198
35 234
Guide pin

4-M12 324 Datum plane

330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 35
B A 35

A 35

Plate S
B
U

25

25
25

C
C

30

30
30
35

35

35

200
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4045 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 4
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4045 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 35

B 35 A 35
B 35 A 35

Plate S
Plate S Plate S
U
25

C
C

C
30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
201
 S Series 4050
HT DIMM FK Clamping plate spec. TW
80～365 Ｍ24 Clamping type 450
370～430 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

212
424
304

474
500
440

210
25
Return pin

2 X 6-M16 198
35 234 Datum plane
Guide pin

4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25

25
25

C
C

30

30
30
35

35

35

202
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4050 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 5
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4050 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 35

B 35 A 35
B 35 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

C
30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
203
 S Series 4055
HT DIMM FK Clamping plate spec. TW
80～310 Ｍ24 Clamping type 450
315～430 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

237
524
550
490
474
354

235
25
Return pin

2 x 6-M16 198
35 234 Datum plane
Guide pin

4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

204
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4055 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 5
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4055 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 35

B 35 A 35
B 35 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
205
 S Series 4060
HT DIMM FK Clamping plate spec. TW
80～265 Ｍ24 Clamping type 450
270～430 Ｍ30 Bolt-fastening type 550
TW
400
68 260 68
FK

262
540

574
600
524
404

25 260
Return pin

2 X 6-M16 198
35 234
Guide pin
Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

206
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4060 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 6
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4060 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 35

B 35 A 35
B 35 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
207
 S Series 4070
HT DIMM FK Clamping plate spec. TW
80～195 Ｍ24
TW Clamping type 450
200～430 Ｍ30 400 Bolt-fastening type 550

68 260 68
FK

312

700
674
624
640

504

310
25
Return pin

2 X 6-M16 198
35 234
Guide pin

324 Datum plane

4-M12
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 35 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

208
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4070 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 7
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 450

X 550 U DIMM
V 50
Y 450 W 70
— Types without backing plate
Z 550

■ How to order optional specification

■ Order example MDC SB 4070 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 35 A 35

B 35 A 35
B 35 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
209
 S Series 4545
HT DIMM FK Clamping plate spec. TW
80～360 Ｍ24 Clamping type 500
365～440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

182
424
384
364
236

450
180
30
Return pin

2 x 6-M16 226
40 264
Guide pin

4-M12 364 Datum plane

370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

210
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4545 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
5
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 4
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
J 500

S 550 U DIMM
V 60
K 500 W 80
— Types without backing plate
Y 550

■ How to order optional specification

■ Order example MDC SB 4545 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
211
 S Series 4550
HT DIMM FK Clamping plate spec. TW
80～300 Ｍ24 Clamping type 500
305～440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

207
434
414
286

500
474
205
30
Return pin

2 X 6-M16 226
40 264
Guide pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

212
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4550 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
5
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 5
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
J 500

S 550 U DIMM
V 60
K 500 W 80
— Types without backing plate
Y 550

■ How to order optional specification

■ Order example MDC SB 4550 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
213
 S Series 4555
HT DIMM FK Clamping plate spec. TW
80～250 Ｍ24 Clamping type 500
255～440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

232

550
336
464

524
484

230
30
Return pin

2 X 6-M16 226
40 264
Guide pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

214
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4555 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
5
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 5
This may be changed to J or P by 5
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
J 500

S 550 U DIMM
V 60
K 500 W 80
— Types without backing plate
Y 550

■ How to order optional specification

■ Order example MDC SB 4555 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
215
 S Series 4560
HT DIMM FK Clamping plate spec. TW
80～210 Ｍ24 Clamping type 500
215～440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

257
386
534
514

600
574
255
30
Return pin

2 X 6-M16 226
40 264
Guide pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

216
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 4560 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 4
5
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 6
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
J 500

S 550 U DIMM
V 60
K 500 W 80
— Types without backing plate
Y 550

■ How to order optional specification

■ Order example MDC SB 4560 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
217
 S Series 5050
HT DIMM FK Clamping plate spec. TW
80～220 Ｍ24 Clamping type 600
225～440 Ｍ30 Bolt-fastening type 700

TW
500
88 320 88
FK

207
434
414
286

474
500
205
30
Return pin

2 X 6-M16 256
40 294
Guide pin
Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

218
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5050 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 5
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 5
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 600

X 700 U DIMM
V 60
Y 600 W 80
— Types without backing plate
Z 700

■ How to order optional specification

■ Order example MDC SB 5050 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
219
 S Series 5060
HT DIMM FK Clamping plate spec. TW
80～380 Ｍ30 Clamping type 600
385～440 Ｍ36 Bolt-fastening type 700

TW
500
88 320 88
FK

257
534
514
386

574
600
255
30
Return pin

2 X 6-M16 256
40 294
Guide pin
Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

220
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5060 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 5
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 6
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 600

X 700 U DIMM
V 60
Y 600 W 80
— Types without backing plate
Z 700

■ How to order optional specification

■ Order example MDC SB 5060 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
221
 S Series 5070
HT DIMM FK Clamping plate spec. TW
80～280 Ｍ30 Clamping type 600
285～440 Ｍ36 Bolt-fastening type 700
● The dimension of Plate A or Plate TW
B is 40, M30 is applied for FK.
500
88 320 88
FK

307
674
700
634
614
486

305
30
Return pin

2 X 6-M16 256
40 294
Guide pin
Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U

25
25

25
C

C
C

30
30

30
35

35

35

222
TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5070 70 70 10 S V M N Option

Type SA SB SC SD SE SF

Nominal Dimension 5
0
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 7
This may be changed to J or P by 0
40 50 60 70 80 90 Futaba if there is any addition or
B DIMM 100 110 120 130 140 150 change to the specification.

C DIMM 100 110 120 130

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Specification of ejector plate
※ When selecting SE or SF without Plate C, specify 00.
M Counterbore type
Width of clamping Orientation of L Spacer type
plate TW guide
— When selecting SE or SF type
S 600

X 700 U DIMM
V 60
Y 600 W 80
— Types without backing plate
Z 700

■ How to order optional specification

■ Order example MDC SB 5070 10 60 10 S V M N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Removes the threaded holes for eye bolts for Plate See the separate volume“Additional Mold Base
#FK A and B
processing Processing & Mold Parts Edition”for details.

SDtype SEtype SFtype

B 40 A 35

B 40 A 35
B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C
C

30

35

35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
223
 S Series 5555
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700

TW
550
100 340 100

222
480
444
300

520
550
220
30
Return pin

2 X 6-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

224
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5555 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 5
U DIMM 5
60 70 80 90 100 110 120 V 70
B DIMM 130 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5555 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 400 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 405 ∼ 560 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
225
 S Series 5560
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700

TW
550
100 340 100

247
570
600
530
494
350

245
30
Return pin

2 X 6-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

226
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5560 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 6
U DIMM 0
60 70 80 90 100 110 120 V 70
B DIMM 130 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5560 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 350 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 355 ∼ 560 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
227
 S Series 5565
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700

TW
550
100 340 100

272
580
544
400

620
650
270
30
Return pin

2 X 6-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

228
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5565 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 6
U DIMM 5
60 70 80 90 100 110 120 V 70
B DIMM 130 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5565 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 310 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 315 ∼ 560 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
229
 S Series 5570
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700

TW
550
100 340 100

297
670
700
630
594
450

295
30
Return pin

2 X 6-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

230
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5570 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 7
U DIMM 0
60 70 80 90 100 110 120 V 70
B DIMM 130 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5570 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 270 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 275 ∼ 530 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) 535 ∼ 560 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
231
 S Series 5575
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700

TW
550
100 340 100

322
680
644
500
170

720
750
30
Return pin 320

2 X 8-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

232
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5575 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
80 90 100 110 120 130
A DIMM 150 160 180 200 220 250 — When selecting SE or SF type 7
U DIMM 5
80 90 100 110 120 130 V 70
B DIMM 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5575 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
160 ∼ 240 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 245 ∼ 480 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) 485 ∼ 560 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
233
 S Series 5580
Clamping plate spec. TW
Clamping type 600
Bolt-fastening type 700
TW
550
100 340 100

347
730
694
550
180

770
800
345
30
Return pin

2 X 8-M20 270
50 310
Guide pin
Datum plane
6-M12 444
450

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 40 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

234
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5580 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 5
L Spacer type 5
80 90 100 110 120 130
A DIMM 150 160 180 200 220 250 — When selecting SE or SF type 8
U DIMM 0
80 90 100 110 120 130 V 70
B DIMM 150 160 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 600
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 700

Y 600

Z 700

■ How to order optional specification

■ Order example MDC SC 5580 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
160 ∼ 210 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 215 ∼ 440 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) 445 ∼ 560 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 40 A 35
B 40 A 35

B 40 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35
35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
235
 S Series 6060

700
600
100 390 100

247
570
600
530
494
350

245
30
Return pin

2 X 6-M20 320
50 360
Guide pin
Datum plane
6-M12 494
500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 50 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25

C
C

30
30

30
35

35

35

236
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6060 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 0
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 6
U DIMM 0
60 70 80 90 100 110 120 V 80
B DIMM 130 150 160 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6060 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 320 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 325 ∼ 580 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 50 A 35

B 50 A 35
B 50 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
237
 S Series 6065

700
600
100 390 100

272
620
650
580
544
400

270
30
Return pin

2 X 6-M20 320
50 360
Guide pin
Datum plane
6-M12 494
500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 50 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25

C
C

30
30

30
35

35

35

238
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6065 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 0
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 6
U DIMM 5
60 70 80 90 100 110 120 V 80
B DIMM 130 150 160 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6065 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 280 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 285 ∼ 540 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) 545 ∼ 580 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 50 A 35

B 50 A 35
B 50 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
239
 S Series 6070

700
600
100 390 100

297
630
594
450

670
700
295
30
Return pin

2 X 6-M20 320
50 360
Guide pin
Datum plane
6-M12 494
500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 50 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25

C
C

30
30

30
35

35

35

240
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6070 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 0
60 70 80 90 100 110 120
A DIMM 130 150 160 180 200 220 250 — When selecting SE or SF type 7
U DIMM 0
60 70 80 90 100 110 120 V 80
B DIMM 130 150 160 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6070 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
120 ∼ 240 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 245 ∼ 480 M36 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) 485 ∼ 580 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 50 A 35

B 50 A 35
B 50 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
241
 S Series 6075

700
600
100 390 100

322
720
750
680
644
500
170

320
30
Return pin

2 X 8-M20 320
50 360
Guide pin
Datum plane
6-M12 494
500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 50 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25

C
C

30
30

30
35

35

35

242
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6075 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 0
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 7
U DIMM 5
100 110 120 130 150 160 V 80
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6075 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 440 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 445 ∼ 580 M42 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 50 A 35

B 50 A 35
B 50 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
243
 S Series 6080

700
600
100 390 100

347
730
694
550
180

770
800
345
30
Return pin

2 X 8-M20 320
50 360
Guide pin
Datum plane
6-M12 494
500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 50 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25

C
C

30
30

30
35

35

35

244
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6080 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 0
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 8
U DIMM 0
100 110 120 130 150 160 V 80
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6080 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 400 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 405 ∼ 580 M42 Plate S Stripper plate M16
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 50 A 35

B 50 A 35
B 50 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
245
 S Series 6565

750
650
120 400 120

272
620
650
580
544
400

270
30
Return pin

2 X 6-M20 330
50 370
Guide pin
Datum plane
6-M12 530
544

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

246
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6565 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 5
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 6
U DIMM 5
100 110 120 130 150 160 V 90
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6565 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 230 M30 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 235 ∼ 480 M36 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) 485 ∼ 600 M42 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 35
B 60 A 35

B 60 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
247
 S Series 6570

750
650
120 400 120

297
670
700
630
594
450
150

295
30
Return pin

2 X 8-M20 330
50 370
Guide pin
Datum plane
6-M12 530
544

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

248
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6570 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 5
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 7
U DIMM 0
100 110 120 130 150 160 V 90
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6570 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 430 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 435 ∼ 600 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 35
B 60 A 35

B 60 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
249
 S Series 6575

750
650
120 400 120

322
720
750
680
644
500
170

320
30
Return pin

2 X 8-M20 330
50 370
Guide pin
Datum plane
6-M12 530
544

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

250
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6575 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 5
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 7
U DIMM 5
100 110 120 130 150 160 V 90
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6575 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 380 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 385 ∼ 600 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 35
B 60 A 35

B 60 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
251
 S Series 6580

750
650
120 400 120

347
730
694
550
180

770
800
345
30
Return pin

2 X 8-M20 330
50 370
Guide pin
Datum plane
6-M12 530
544

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 35
B A 35

A 35

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
35

35

35

252
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6580 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 6
L Spacer type 5
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 8
U DIMM 0
100 110 120 130 150 160 V 90
B DIMM 180 200 — Types without backing plate

Orientation of guide
C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） S
※ When selecting SE or SF without Plate C, specify 00.

■ How to order optional specification

■ Order example MDC SC 6580 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 350 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 355 ∼ 600 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 35
B 60 A 35

B 60 A 35

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

30

35
35

35

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
253
 S Series 7070
Clamping plate spec. TW
Clamping type 800
Bolt-fastening type 890

TW
700
120 450 120

290
630
580
420
140

670
700
288
30
Return pin

2 X 8-M20 380
60 420
Guide pin
Datum plane
6-M12 580

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 40
B A 40

A 40

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
40

40

40

254
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 7070 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 7
L Spacer type 0
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 7
U DIMM 0
100 110 120 130 150 160 V 100
B DIMM 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 800
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 890

Y 800

Z 890

■ How to order optional specification

■ Order example MDC SC 7070 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 360 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 365 ∼ 610 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 40

B 60 A 40
B 60 A 40

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

C
30

40

40
40

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
255
 S Series 7075
Clamping plate spec. TW
Clamping type 800
Bolt-fastening type 890

TW
700
120 450 120

315
680
630
470
160

720
750
313
30
Return pin

2 X 8-M20 380
60 420
Guide pin
Datum plane
6-M12 580

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 40
B A 40

A 40

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
40

40

40

256
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 7075 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 7
L Spacer type 0
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 7
U DIMM 5
100 110 120 130 150 160 V 100
B DIMM 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 800
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 890

Y 800

Z 890

■ How to order optional specification

■ Order example MDC SC 7075 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 320 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 325 ∼ 590 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) 595 ∼ 610 M48 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 40

B 60 A 40
B 60 A 40

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

C
30

40

40
40

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
257
 S Series 7080
Clamping plate spec. TW
Clamping type 800
Bolt-fastening type 890

TW
700
120 450 120

340
730
680
520
170

800
770
338
30
Return pin

2 X 8-M20 380
60 420
Guide pin
Datum plane
6-M12 580

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

SAtype SBtype SCtype

B 60 A 40
B A 40

A 40

Plate S
HT
HT

HT
B
U
U

25
25
25
C

30
30

30
40

40

40

258
 TD Technical Data P.787

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 7080 10 10 12 S V M N Option
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector plate
Nominal Dimension M Counterbore type 7
L Spacer type 0
100 110 120 130 150 160
A DIMM 180 200 220 250 — When selecting SE or SF type 8
U DIMM 0
100 110 120 130 150 160 V 100
B DIMM 180 200 — Types without backing plate

Width of clamping plate TW Orientation of guide

C DIMM 100 120 150 170
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
S 800
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00. X 890

Y 800

Z 890

■ How to order optional specification

■ Order example MDC SC 7080 10 12 10 S - M N / #FA

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A #FK Removes the threaded holes for eye bolts for all Plates

#FB Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base Processing &
processing Mold Parts Edition”for details.

■ Specification of threaded holes for eye bolts

Name of the plate HT DIMM Nominal size of thread Name of the plate Nominal size of thread
200 ∼ 280 M36 Plate T and L Clamping plate M16
Plate A: Cavity plate (fixed half) 285 ∼ 530 M42 Plate S Stripper plate M20
Plate B: Cavity plate (moving half) 535 ∼ 610 M48 Plate C Spacer block M16
Plate U: Backing plate Plate E Ejector retainer plate M16
Plate F Ejector base plate M16
※ Threaded holes for eye bolts for cavity plates (fixed and moving halves) and backing plate are determined by HT dimension. Threaded holes for eye bolts for the other plates are defined as listed above.

SDtype SEtype SFtype

B 60 A 40

B 60 A 40
B 60 A 40

Plate S
Plate S Plate S
HT

HT
HT

U
25

C
C

C
30

40

40
40

※ SE and SF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
259
 S Series Material Change Option

SA type SB type SC type

Plate A
Plate A Plate S
Plate A
Plate B Plate B
Plate B

SD type SE type SF type

Plate A
Plate A Plate S Plate A
Plate S Plate B Plate S
Plate B Plate B

■ How to order material change specification

■ Order example MDC SA 2025 40 30 60 S V M N / F – AB

Material changing plate code

A Cavity plate (fixed half)
S Stripper plate
B Cavity plate (moving half)
Mold base order code
Following the － symbol, specify the
When ordering, specify the mold material changing plate. The plate of
base specification with codes shown which material can be changed are the
in each page. above three types, Plate A, S and B.

Material designation code

◆How to order F HPM1
In addition to the mold base order codes, please specify K NAK55
“Material designation code” and “Material changing R NAK80
plate code”. A AAS (aluminum alloy A7075 or equivalent)

260
TD Technical Data P.787

︲2 PlateType
Material Mold base

S series
Material name Plate A thickness Plate B thickness Plate S thickness
designation code nominal dimension
1515
1518
1520
1523
15 20 30 40
1818 20 25 30 35 40 20 25 30 35 40
1820

Material Change Option

1823
1825
F HPM1 2020
K NAK55 2023
R NAK80 2025 25 30 35 40 25 30 35 40
20 30 40

2030
2323
2325
20 30 40 50
2327 25 30 35 40 50 25 30 35 40 50
2330
2525
2527 25 30 40 50
30 35 40 50 30 35 40 50
2530
1515
1518
1520
20 25 30 35 40 50 60 20 25 30 35 40 50 60 15
1818
1820
1825
2020
2025 20 25 30 35 40 50 60 70 80 20 25 30 35 40 50 60 70 80
∗ 2030
AAS 2323
20
A （aluminum alloy A7075 or
2325
equivalent）
2330
25 30 35 40 50 60 70 80 25 30 35 40 50 60 70 80
2525
2530 25
2535
3030 30 35 40 50 60 70 80 90 100 30 35 40 50 60 70 80 90 100
3035 30
35 40 50 60 70 80 90 100 35 40 50 60 70 80 90 100
3040
3540
40 50 60 70 80 90 100 40 50 60 70 80 90 100 35
4040
＊ When using AAS, specify the AAS for all of Plate A, Plate S and Plate B. If Plate S is not used, specify AAS for Plate A and Plate B. As the thermal expansion
coefficients of aluminum alloy and steel are completely different, these two materials cannot be combined.
※Product of materials and sizes not listed above will also be made to order. Please consult our sales office.

261
262
 LARGE-SIZE S-SERIES
Large-Size S series
■Large-Size S Series Overview ・・・・・・・・・・・・・・・・・・・・・・・・・ P.264

■Large-Size S Series

  Width 550 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.268

  Width 600 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.270

  Width 650 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.272

  Width 700 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.274

  Width 750 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.276

  Width 800 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.278

  Width 850 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.280

  Width 900 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.282

 Large-Size S series Overview
■ Features of large-size S series
This series standardizes 34 types of mold bases with mold plate sizes from 550×850 to 900×1000. The
configuration of a mold base is the same as that of other 2-plate type S series, but items that need to select or
specify are increased as shown below.
1. The combination of spacer block width and ejector plate width (M specification or B specification) can be selected as
follows:
●Combination table of spacer blocks and ejector plates
Ejector plate M specification B specification
specification
Nominal dimension CW EFW CX CW EFW CX
5585 ∼ 5510 100 340 5 – – –
6085 ∼ 6010 100 390 5 120 350 5
6585 ∼ 6510 100 440 5 120 400 5
7085 ∼ 7010 100 490 5 120 450 5
7575 ∼ 7510 120 490 10 140 450 10
8080 ∼ 8010 120 550 5 140 510 5 CW EFW CW
8585 ∼ 8510 140 560 5 160 510 10 CX CX
9090 ∼ 9010 140 610 5 160 560 10
※For the combination of nominal dimension 5585 to 5510, only M specification is available.
2. As the diameter of return pins is defined, please specify the pitch.
3. As the number of hexagon socket head cap screws and nominal size of threads are defined, please specify the pitch.
4. Please specify the threaded hole for eye bolts, taking account in the weight of the mold base.

■ How to order
For large-size S series, the dimension tables and drawings are shown by width of mold plates in two-facing
pages from P.268 to P.283. As the dimension tables are shown on the left page and order examples are on the
right page as below, specify the specifications and dimensions with codes and numbers shown in the table. The
length of guide pins, the pitch of return pins and hexagon socket head cap screws and threaded holes for eye
bolts needs to be specified with codes for“additional processing specifications”
.

●Dimension drawing & tables

TW Clamping plate spec. TW
Clamping type 800
700
Bolt-fastening type 890
CW EFW CW
Ejector plate width Spacer block width
EFW CW
490 100
450 120
GP2

Guide pin
Nominal
GP3

L Pitch
L

dimension Dia. Length

GP1 GP2 GP3
GP1

7085 850 363 365 730 Please specify.

30 ※ How to specify ☞
Return pin
7090 900 388 390 780 See P.48 of our separate
φ 60
7095 950 413 415 830 volume“Additional Mold
Base Processing & Mold
60 580 Datum plane 7010 1000 438 440 880 Parts Edition”.
Guide pin

264
●Order example
（Mold base structure）

S series
2-Plate Type
■ Order example MDC SA 7085 13 10 10 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Overview
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 490 100
A DIMM 230 250 260 270 300 320 350
B 450
When selecting SE or 120
100 110 120 130 150 160 180 200 220 — SF type
B DIMM 230 250 260 270 300 320 350 U DIMM
V 100
C DIMM 100 120 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ） Width of clamping Orientation of
※ When selecting SE or SF without Plate C, specify 00. plate guide

S 800

X 890

Y 800

Z 890
●Items to specify (items other than mold base structure)
Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can
Pitch of return pins be specified.
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

265
 Large-Size S series Overview
■Order examples
This section describes the outline of the ordering procedures, taking the following mold base specification as an example.
800
700
100 490 100
M42

120 180

277
820
250

300
590
770
850

150
410
460
610

●Outline of ordering procedures

Item to specify Specification example Order code example
Mold base structure Type SA Type MDC SA 7085 18 12 15 S V M N
Size of mold plates 700×850
Thickness of cavity plate (fixed half) 180
Thickness of cavity plate (moving half) 120
Width of spacer block 100
Height of spacer block 150
Width of ejector plate 490
Guide pin length L dimension 277 CGPGB1 － GPHO － L277
How to specify ☞ See P.48 in the (SL dimension will be set by
separate volume“Additional Mold Futaba. However, if there is any
L

Base Processing & Mold Parts desired value, please specify it.)
SL

Edition”

Pitch of return pins A dimension 410 CPP － RP － A410 － B770

How to specify ☞ See P.76 in the B dimension 770
separate volume“Additional Mold
B

Base Processing & Mold Parts

Edition”
A
For clamping plate A dimension 610 CPNP － TCS － S101 － A610 － B590 － C300
Pitch of hexagon socket head cap screws

How to specify ☞ See B dimension 590 CPNP － LCS － S101 － A610 － B590 － C300
P.78 in the separate volume C dimension 300
B
C

“Additional Mold Base (Different pitches can be

Processing & Mold Parts specified for TCS and LCS)
A
Edition” Position code S101
For ejector plate A dimension 460 CPNP － ECS － S081 － A460 － B820 － C250
How to specify ☞ See P.78 B dimension 820
in the separate volume C dimension 250
B
C

“Additional Mold Base

Processing & Mold Parts Position code S081
A
Edition”
Threaded holes for eye bolts M Machines M42 threaded holes at MFK2AC － A － M42 － H90
How to specify ☞ See P.226 in the positions shown on the left MFK2AC － B － M42 － H60
the separate volume“Additional figure on the cavity plates (fixed
Mold Base Processing & Mold and moving halves).
Parts Edition”

266
Thus, the order code will be as follows:

S series
2-Plate Type
Mold base structure-------------------------- MDC SA 7085 18 12 15 S V M N
Please specify desired specification with codes Guide pin length ----------------------------- CGPGB1 － GPHO － L277
as shown in the portion. Pitch of return pins--------------------------- CPP － RP － A410 － B770
Pitch of hexagon socket head cap screws --- CPNP － TCS － S101 － A610 － B590 － C300
CPNP － LCS － S101 － A610 － B590 － C300
CPNP － ECS － S081 － A460 － B820 － C250

Overview
Threaded holes for eye bolts ----------------- MFK2AC － A － M42 － H90
MFK2AC － B － M42 － H60

■ Additional processing
Other additions or changes to the standard specification are also available.
For details, please refer to the separate volume“Additional Mold Base Processing & Mold Parts Edition”
.

■ Price
We will be pleased to provide you with a preliminary price quotation. Please request a quotation from our sales office.

■ Large-size S series machining standard

● Machining of holes for guide pins and return pins
If the plate thickness is over 200 when installing a guide pin and over 150 when installing a return pin, a relief
should be provided on the opposite side of the PL surface as shown below.

Depending on the thickness

of the mold plate, the guide
bushing may be changed to
M-GBB. PL surface (parting line surface)

d D
150

※ Details ☞ See P.31 in the

200

separate volume“Additional
Processing & Mold Parts
d+1 D+1
Edition”

d D
50 60 70 30 35

■ Specifications not listed in the catalogs

For specifications not listed in the catalogs, specify with a drawing or consult your nearest Futaba sales office.

267
 Large-SizeS series Width 550
TW Clamping plate spec. TW
Clamping type 600
550 Bolt-fastening type 700
100 340 100
Guide pin
Nominal
L Pitch
dimension Dia. Length
GP1 GP2 GP3
5585 850 370 372 744 Please specify.

GP2
※ How to specify ☞
5590 900 395 397 794 See P.48 of our separate
φ 50
GP3

5595 950 420 422 844 volume“Additional Mold

L
Base Processing & Mold
5510 1000 445 447 894 Parts Edition”.
30 GP1
Return pin

50 444 Datum plane

Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

5585 5590･5595･5510
8-M20 8-M20
TCS TCS
LCS LCS

8-M12 10-M12
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
B 40 A 35
B A 35

A 35
B
70

70

25
25

25
C

30
30

30
35

35

35

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
B 40 A 35
B 40 A 35

B 40 A 35
70
25

C
C

C
30

35
35

35

LCS ECS LCS LCS

268
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 5585 13 10 10 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table M Counterbore type
— When selecting SE or SF type
80 90 100 110 120 130 150 160 180
A DIMM 200 220 250 260 270 280 300 320 350 U DIMM
V 70
80 90 100 110 120 130 150 160 180 — Types without backing plate
B DIMM 200 220 250 260 270 280 300 320 350
Width of clamping plate Orientation of guide

C DIMM 100 120 150 170 S 600

※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers. 5
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
X 700 5
0
Y 600

Z 700

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch.
Pitch of return pins Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold
Pitch of hexagon socket
LCS bases. Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 5585 10 12 10 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A270 － B780
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S081 － A450 － B600 － C200
CPNP － LCS － S081 － A450 － B600 － C200
CPNP － ECS － S081 － A310 － B820 － C270
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M30
MFK2AC － B － M30
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

269
 Large-SizeS series Width 600
700
600
CW EFW CW
Ejector plate width Spacer block width
EFW CW
390 100
350 120

GP2
Guide pin
Nominal
GP3

L Pitch

L
dimension Dia. Length
GP1 GP2 GP3

GP1
6085 850 370 372 744 Please specify.
30 ※ How to specify ☞
Return pin
6090 900 395 397 794 See P.48 of our separate
φ 50
6095 950 420 422 844 volume“Additional Mold
Base Processing & Mold
50 494 Datum plane 6010 1000 445 447 894 Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

6085 6090･6095･6010
8-M20 10-M20
TCS TCS
LCS LCS

8-M12 10-M12
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
B 50 A 35
B A 35

A 35
B
80

80

25
25

25
C

30
30

30
35

35

35

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
B 50 A 35
B 50 A 35

B 50 A 35
80
25

C
C

C
30

35
35

35

LCS ECS LCS LCS

270
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6085 13 10 10 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 390 100
A DIMM 250 260 270 280 300 320 350
B 350
120
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 250 260 270 280 300 320 350 U DIMM
V 80
C DIMM 100 120 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
6
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
0
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 6085 10 12 10 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A320 － B780
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S081 － A500 － B600 － C200
CPNP － LCS － S081 － A500 － B600 － C200
CPNP － ECS － S081 － A360 － B820 － C270
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M36
MFK2AC － B － M36
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

271
 Large-SizeS series Width 650
750
650
CW EFW CW
Ejector plate width Spacer block width
EFW CW
440 100
400 120

GP2
Guide pin
Nominal
GP3

L Pitch

L
dimension Dia. Length
GP1 GP2 GP3

GP1
6585 850 370 372 744 Please specify.
30 ※ How to specify ☞
Return pin
6590 900 395 397 794 See P.48 of our separate
φ 50
6595 950 420 422 844 volume“Additional Mold
Base Processing & Mold
50 544 Datum plane 6510 1000 445 447 894 Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

6585 6590･6595･6510
10-M20 10-M20
TCS TCS
LCS LCS

8-M12 10-M12
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
B 60 A 35
B A 35

A 35
B
90

90

25
25

25
C

30
30

30
35

35

35

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
B 60 A 35
B 60 A 35

B 60 A 35
90
25

C
C

C
30

35
35

35

LCS ECS LCS LCS

272
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 6585 13 10 10 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 440 100
A DIMM 250 260 270 300 320 350
B 400
120
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 250 260 270 300 320 350 U DIMM
V 90
C DIMM 100 120 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
6
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
5
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 6585 10 12 10 S － B N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A330 － B780
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S101 － A530 － B600 － C300
CPNP － LCS － S101 － A530 － B600 － C300
CPNP － ECS － S081 － A370 － B820 － C270
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M36
MFK2AC － B － M36
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

273
 Large-SizeS series Width 700
TW Clamping plate spec. TW
Clamping type 800
700 Bolt-fastening type 890
CW EFW CW
Ejector plate width Spacer block width
EFW CW
490 100
450 120

GP2
Guide pin
Nominal
GP3

L Pitch

L
dimension Dia. Length
GP1 GP2 GP3

GP1
7085 850 363 365 730 Please specify.
30 ※ How to specify ☞
Return pin
7090 900 388 390 780 See P.48 of our separate
φ 60
7095 950 413 415 830 volume“Additional Mold
Base Processing & Mold
60 580 Datum plane 7010 1000 438 440 880 Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

7085 7090 7095･7010

10-M20 10-M20 12-M20
TCS TCS TCS
LCS LCS LCS

8-M12 10-M12 10-M12

ECS ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
100 B 60 A 40
100 B A 40

A 40
B
25
25

25
C

30
30

30
40

40

40

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
100 B 60 A 40
B 60 A 40

B 60 A 40
25

C
C

C
30

40
40

40

LCS ECS LCS LCS

274
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 7085 13 10 10 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 490 100
A DIMM 230 250 260 270 300 320 350
B 450
120
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 230 250 260 270 300 320 350 U DIMM
V 100
C DIMM 100 120 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Width of clamping plate Orientation of guide
7
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
0
S 800 0
X 890

Y 800

Z 890
■ Other items to specify
Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 7085 10 12 10 S － B N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A380 － B780
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S101 － A580 － B570 － C280
CPNP － LCS － S101 － A580 － B570 － C280
CPNP － ECS － S081 － A420 － B820 － C270
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M36
MFK2AC － B － M36
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

275
 Large-SizeS series Width 750
890
Ejector plate width Spacer block width
750
EFW CW
CW EFW CW 490 120
450 140

Guide pin
Nominal
L Pitch

GP2
dimension Dia. Length
GP1 GP2 GP3
7575 750 313 315 630
GP3

L
7580 800 338 340 680 Please specify.
※ How to specify ☞
30 GP1 7585 850 363 365 730
φ 60
See P.48 of our separate
Return pin
7590 900 388 390 780 volume“Additional Mold
Base Processing & Mold
7595 950 413 415 830 Parts Edition”.
60 630 Datum plane 7510 1000 438 440 880
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

7575･7580･7585 7590･7595･7510
10-M20 12-M20
TCS TCS
LCS LCS

8-M12 10-M12
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
110 B 70 A 40
110 B A 40

A 40
B
30
30

30
C

40
40

40
40

40

40

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
110 B 70 A 40
B 70 A 40

B 70 A 40
30

C
C

C
40

40
40

40

LCS ECS LCS LCS

276
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 7575 13 10 12 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 490 120
A DIMM 230 250 260 300 350
B 450
140
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 230 250 260 300 350 U DIMM
V 110
C DIMM 120 130 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
7
e.g.:（100→ 10 ）
5
※ When selecting SE or SF without Plate C, specify 00.
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 7575 10 12 12 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A420 － B680
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S101 － A630 － B470 － C240
CPNP － LCS － S101 － A630 － B470 － C240
CPNP － ECS － S081 － A460 － B720 － C240
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M36
MFK2AC － B － M36
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

277
 Large-SizeS series Width 800
890
800
CW EFW CW Ejector plate width Spacer block width
EFW CW
550 120
510 140

GP2
Guide pin
Nominal
L Pitch
dimension Dia. Length
GP3

GP1 GP2 GP3

L
8080 800 328 330 660
Please specify.
35 GP1 8085 850 353 355 710 ※ How to specify ☞
Return pin See P.48 of our separate
8090 900 378 380 760 φ 70
volume“Additional Mold
8095 950 403 405 810 Base Processing & Mold

70 660 Datum plane 8010 1000 428 430 860

Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

8080･8085 8090 8095･8010

8-M24 8-M24 10-M24
TCS TCS TCS
LCS LCS LCS

8-M16 10-M16 10-M16

ECS ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
120 B 70 A 40
120 B A 40

A 40
B
30
30

30
C

40
40

40
40

40

40

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
120 B 70 A 40
B 70 A 40

B 70 A 40
30

C
C

C
40

40
40

40

LCS ECS LCS LCS

278
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 8080 13 10 12 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 550 120
A DIMM 230 250 260 300 350
B 510
140
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 230 250 260 300 350 U DIMM
V 120
C DIMM 120 130 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
8
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
0
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 8080 10 12 12 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A460 － B720
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S081 － A660 － B480 － C160
CPNP － LCS － S081 － A660 － B480 － C160
CPNP － ECS － S081 － A510 － B760 － C250
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M36
MFK2AC － B － M36
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

279
 Large-SizeS series Width 850
950
850
CW EFW CW
Ejector plate width Spacer block width
EFW CW
560 140
510 160

GP2
Guide pin
Nominal
GP3

L Pitch

L
dimension Dia. Length
GP1 GP2 GP3

GP1
8585 850 353 355 710 Please specify.
35 ※ How to specify ☞
Return pin
8590 900 378 380 760 See P.48 of our separate
φ 70
8595 950 403 405 810 volume“Additional Mold
Base Processing & Mold
70 710 Datum plane 8510 1000 428 430 860 Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

8585 8590･8595･8510
10-M24 10-M24
TCS TCS
LCS LCS

8-M16 10-M16
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
130 B 70 A 40
130 B A 40

A 40
B
30
30

30
C

40
40

40
40

40

40

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
130 B 70 A 40
B 70 A 40

B 70 A 40
30

C
C

C
40

40
40

40

LCS ECS LCS LCS

280
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 8585 13 10 13 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 560 140
A DIMM 230 250 270 300 350
B 510
160
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 230 250 270 300 350 U DIMM
V 130
C DIMM 130 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
8
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
5
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 8585 10 12 13 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A470 － B770
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S101 － A710 － B520 － C260
CPNP － LCS － S101 － A710 － B520 － C260
CPNP － ECS － S081 － A520 － B810 － C270
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M42
MFK2AC － B － M42
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

281
 Large-SizeS series Width 900
1150
900
CW EFW CW
Ejector plate width Spacer block width
EFW CW
610 140
560 160

GP2
Guide pin
Nominal
GP3

L Pitch

L
dimension Dia. Length
GP1 GP2 GP3

GP1
Please specify.
35 9090 900 378 380 760
Return pin
※ How to specify ☞
See P.48 of our separate
9095 950 403 405 810 φ 70
volume“Additional Mold
Base Processing & Mold
70 760 Datum plane
9010 1000 428 430 860
Parts Edition”.
Guide pin

●The layout of hexagon socket head cap screws　(the layout may differ depending on the nominal dimensions).

9090 9095･9010
10-M24 12-M24
TCS TCS
LCS LCS

10-M16 10-M16
ECS ECS

Please specify the pitches for ECS, TCS and LCS (different pitches can be specified for TCS and LCS).
※How to specify ☞ P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

SAtype SBtype SCtype

TCS
TCS
TCS
150 B 70 A 50
150 B A 50

A 50
B
30
30

30
C

40
40

40
50

50

50

LCS ECS LCS ECS LCS ECS

SDtype SEtype SFtype

TCS
TCS TCS
150 B 70 A 50
B 70 A 50

B 70 A 50
30

C
C

C
40

50
50

50

LCS ECS LCS LCS

282
TD Technical Data P.787 AP Additional processing Separate volume“Additional Mold Base Processing & Mold Parts Edition”

︲2 PlateType
■ How to order

S series
■ Order example MDC SA 9090 13 10 13 S V M N
（Mold base structure）
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
Type SA SB SC SD SE SF
Specification of ejector Plates

Large-Size Width
Nominal dimension See left table Ejector plate width Spacer block width
EFW CW
100 110 120 130 150 160 180 200 220 M 610 140
A DIMM 230 250 270 300 350
B 560
160
— When selecting SE or SF type
100 110 120 130 150 160 180 200 220
B DIMM 230 250 270 300 350 U DIMM
V 150
C DIMM 130 150 170 200 — Types without backing plate
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Orientation of guide
9
e.g.:（100→ 10 ）
※ When selecting SE or SF without Plate C, specify 00.
0
0
S

■ Other items to specify

Item to specify Description
Select the length from the dimension table in page 276 in the separate volume“Additional Mold Base Processing & Mold Parts
Guide pin length Edition ”Even the dimensions not listed in the dimension table can be specified.
※ How to specify ☞ See P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
The diameter of return pins is defined. Please specify the pitch. Even the dimensions not listed in the dimension table can be specified.
Pitch of return pins
※ How to specify ☞ See P.76 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
TCS The number of hexagon socket head cap screws and the nominal size of threads are set by nominal dimension of mold bases.
Pitch of hexagon socket
LCS Please specify the pitch of the hexagon socket head cap screw.
head cap screws
ECS ※ How to specify ☞ See P.78 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”
Specify threaded holes for eye bolts, which are machined on cavity plates and backing plates, etc., by taking into account
Threaded holes for eye bolts the weight of the mold base.
※ How to specify ☞ See P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

■ Order examples including other Mold base structure--------------------------- MDC SC 9090 10 12 13 S － M N

items to specify Guide pin length ------------------------------ CGPGB1 － GPHO － L277 － SL99
Please specify desired specification with codes as Pitch of return pins---------------------------- CPP － RP － A520 － B820
shown in the portion. Pitch of hexagon socket head cap screws ---- CPNP － TCS － S101 － A760 － B580 － C290
CPNP － LCS － S101 － A760 － B580 － C290
CPNP － ECS － S101 － A570 － B860 － C430
Threaded holes for eye bolts ------------------ MFK2AC － T － M16
MFK2AC － A － M42
MFK2AC － B － M42
MFK2AC － C － M16
MFK2AC － E － M16
MFK2AC － F － M16
MFK2AC － L － M16

283
284
 THREE-PLATE TYPE D・E-SERIES
3-Plate Type
D & E series
■Structure and Component Name ・・・・・・・・・・・・・・・・・・・・・・・ P.286

■High Rigidity Type D & E Series

  1518∼1830 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.288∼303

  2020∼2540 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.304∼327

  2730∼3040 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.328∼337

■D & E Series

  1113∼1835 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.338∼363

  2020∼2340 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.364∼389

  2525∼2940 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.390∼417

  3030∼3560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.418∼453

  4040∼4560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.454∼473

  5050∼5070 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.474∼479

■D & E Series Material Change Option・・・・・・・・・・・・・・・・・・・・ P.480

 D&E Series Structure & Component Name

Hexagon socket head cap screw Threaded hole for eye bolt

Support pin

Guide pin & guide bushing Hole for ejector rod

Hexagon socket head cap screw

Return pin

T Top clamping plate

R Runner plate

A Cavity plate (fixed half) GBA Guide Bushing

S Stipper plate GBB Guide Bushing

B Cavity plate (moving half) GPA Guide Pin

U Backing plate
RPN Return pin
SPN Support pin

C Spacer block

E Ejector retainer plate

F Ejector base plate

L Bottom clamping plate

This diagram shows DB type as a representative example.

286
DAType DDType
Stripper plate ejection type without backing
Ejector pin ejection type
plate

T T
R R
A GBA
A GBA
GPA

D & E series
3-Plate Type
B S GBB
U B GPA
RPN SPN
SPN
C C RPN
E E
F F
L L

Structure and Component Name

DBType DEType
Stripper plate ejection type,
Stripper plate ejection type
which is actuated by mold opening behavior

T T
R R
A GBA A GBA
S GBB S GBB
B GPA B GPA
U U
RPN
SPN SPN
C
E C
F
L L

DCType DFType
Ejector pin ejection type without backing Stripper plate ejection type, which is actuated
plate by mold opening behavior, without backing plate

T
T R
R A GBA
A GBA S GBB
B GPA GPA
B
SPN
C SPN
RPN
E C
F
L L

EAType Ejector pin ejection type without runner plate

T
A GBA
B GPA EA type is a mold base specification defined by eliminating a runner

U plate from DA type. Likewise, those defined by eliminating a runner

RPN plate from DB, DC and DD type will become EB, EC and ED type
SPN
C respectively.
E
F
L

287
 High Rigidity Type
D & E Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

72
34

26

162
180
144
96
52

24
70
12 16
Return pin Guide pin

4-M10 28
16 52
Support pin
Datum plane
4-M6 114
120

◆ High regidity type

Standard type P.344
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 25
B A 15 25

Plate R
Plate R
Plate S
U

13
13

C
C

15
15
20

20

288 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.344

■ How to order

■ Order example MDC DA 1518 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
Futaba if there is any addition or 5
S 200 change to the specification.
1
X 230 Specification of ejector 8
U DIMM
B Counterbore type
V 30
Y 200 D Spacer type
W 40
※ The order method (code) of this part is
Z 230 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1518 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 25
A 15 25

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

289
 High Rigidity Type
D & E Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

82
34

36

182
200
116
164

72

34
80
16
12 Guide pin
Return pin

4-M10 28
16 52
Support pin
Datum plane
4-M6 114
120

◆ High regidity type

Standard type P.346
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 25
B A 15 25

Plate R
Plate R
Plate S
U

13
13

C
C

15
15
20

20

290 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.346

■ How to order

■ Order example MDC DA 1520 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 200
Futaba if there is any addition or 5
change to the specification.
2
X 230 U DIMM
Specification of ejector 0
B Counterbore type
V 30
Y 200 D Spacer type
W 40
※ The order method (code) of this part is
Z 230 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1520 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 25
A 15 25

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

291
 High Rigidity Type
D & E Series 1523
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230
TW
150
38 70 38
M12

97
34

51
102
146

212
230
194

49
95
12 16
Guide pin
Return pin

4-M10 28
16 52
Support pin
114 Datum plane
4-M6
120

◆ High regidity type

Standard type P.348
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 25
B A 15 25

Plate R
Plate R
Plate S
U

13
13

C
C

15
15
20

20

292 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.348

■ How to order

■ Order example MDC DA 1523 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 200
Futaba if there is any addition or 5
change to the specification.
2
X 230 U DIMM
Specification of ejector 3
B Counterbore type
V 30
Y 200 D Spacer type
W 40
※ The order method (code) of this part is
Z 230 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1523 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 25
A 15 25

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

293
 High Rigidity Type
D & E Series 1525
Clamping plate spec. TW
Clamping type 200
TW Bolt-fastening type 230

150
38 70 38
M12

107
34

61
214

122

232
250
166

59
105
16
12 Guide pin
Return pin

4-M10 28
16 52
Support pin
Datum plane
4-M6 114
120

◆ High regidity type

Standard type P.350
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 25
B A 15 25

Plate R
Plate R
Plate S
U

13
13

C
C

15
15
20

20

294 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.350

■ How to order

■ Order example MDC DA 1525 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 200
Futaba if there is any addition or 5
change to the specification.
2
X 230 U DIMM
Specification of ejector 5
B Counterbore type
V 30
Y 200 D Spacer type
W 40
※ The order method (code) of this part is
Z 230 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1525 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 25
A 15 25

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

295
 High Rigidity Type
D & E Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

77
34

21 23
154

182
200
164

98
46

20

75
12 Guide pin

Return pin

4-M12 48
20 72
Support pin
140 Datum plane
4-M6
145

◆ High regidity type

Standard type P.354
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 30
B A 15 30

Plate R
Plate R
Plate S
U

U
13

13
C
C

15

15
20

20

296 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.354

■ How to order

■ Order example MDC DA 1820 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 230
Futaba if there is any addition or 8
2
change to the specification.

X 280 U DIMM
Specification of ejector 0
B Counterbore type
V 30
Y 230 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1820 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 30
A 15 30

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

297
 High Rigidity Type
D & E Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

92
34

38

212
230
128
194
184

76

36
90
20
12 Guide pin

Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.356
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 30
B A 15 30

Plate R
Plate R
Plate S
U

U
13

13
C
C

15

15
20

20

298 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.356

■ How to order

■ Order example MDC DA 1823 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 230
Futaba if there is any addition or 8
2
change to the specification.

X 280 U DIMM
Specification of ejector 3
B Counterbore type
V 30
Y 230 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1823 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 30
A 15 30

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

299
 High Rigidity Type
D & E Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

102
34

48

232
250
148
214
204

96

46
100
20
12 Guide pin

Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.358
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 30
B A 15 30

Plate R
Plate R
Plate S
U

U
13

13
C
C

15

15
20

20

300 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.358

■ How to order

■ Order example MDC DA 1825 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 230
Futaba if there is any addition or 8
2
change to the specification.

X 280 U DIMM
Specification of ejector 5
B Counterbore type
V 30
Y 230 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1825 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 30
A 15 30

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

301
 High Rigidity Type
D & E Series 1830
Clamping plate spec. TW

TW Clamping type 230

Bolt-fastening type 280
180
43 90 43
M12

127
34

73
264
254

282
300
198
146

71
125
20
12 Guide pin

Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.360
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 15 A 15 30
B A 15 30

Plate R
Plate R
Plate S
U

U
13

13
C
C

15

15
20

20

302 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.360

■ How to order

■ Order example MDC DA 1830 30 30 60 S V B N OH 160 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 IH
Installs support pins at the inner
positions with bushings
Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 1
S 230
Futaba if there is any addition or 8
3
change to the specification.

X 280 U DIMM
Specification of ejector 0
B Counterbore type
V 30
Y 230 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 1830 40 30 50 S V B N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 15 A 15 30
A 15 30

Plate R
Plate R
Plate S
B

13
13
C

15
15

20
20

303
 High Rigidity Type
D & E Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

34

77
21 23

200
154
164

182
98
46

75
12 20
Return pin Guide pin

4-M12 48
20 72
Support pin
Datum plane
4-M6 154
160

◆ High regidity type

Standard type P.364
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

304 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.364

■ How to order

■ Order example MDC DA 2020 30 30 60 S V B N OH 170 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 250
Futaba if there is any addition or
0
2
change to the specification.

X 280 U DIMM
Specification of ejector 0
B Counterbore type
V 30
Y 250 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2020 40 30 50 S V B N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

305
 High Rigidity Type
D & E Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

92
34

38
194
184
128

230
212
76

36
90
12 20
Return pin Guide pin

4-M12 48
20 72
Support pin
Datum plane
4-M6 154
160

◆ High regidity type

Standard type P.366
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

306 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.366

■ How to order

■ Order example MDC DA 2023 30 30 60 S V B N OH 170 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 250
Futaba if there is any addition or
0
2
change to the specification.

X 280 U DIMM
Specification of ejector 3
B Counterbore type
V 30
Y 250 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2023 40 30 50 S V B N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

307
 High Rigidity Type
D & E Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

102
34

48
214
204
148

250
232
96

46
100
12 20
Return pin Guide pin

4-M12 48
20 72
Support pin
154 Datum plane
4-M6
160

◆ High regidity type

Standard type P.368
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

308 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.368

■ How to order

■ Order example MDC DA 2025 30 30 60 S V B N OH 170 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 250
Futaba if there is any addition or
0
2
change to the specification.

X 280 U DIMM
Specification of ejector 5
B Counterbore type
V 30
Y 250 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2025 40 30 50 S V B N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

309
 High Rigidity Type
D & E Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

127
34

73

282
264
254
198
146

300
71
125
12 20
Return pin Guide pin

6-M12 48
20 72
Support pin

4-M6 154 Datum plane

160

◆ High regidity type

Standard type P.370
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

310 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.370

■ How to order

■ Order example MDC DA 2030 30 30 60 S V B N OH 170 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 50 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 250
Futaba if there is any addition or
0
3
change to the specification.

X 280 U DIMM
Specification of ejector 0
B Counterbore type
V 30
Y 250 D Spacer type
W 40
※ The order method (code) of this part is
Z 280 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2030 40 30 50 S V B N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

311
 High Rigidity Type
D & E Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

92
34

37

230
210
188
184
128
74

35
90
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin
184 Datum plane
4-M8
185

◆ High regidity type

Standard type P.378
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

312 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.378

■ How to order

■ Order example MDC DA 2323 40 40 70 S V B N OH 200 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 280
Futaba if there is any addition or
3
2
change to the specification.

X 350 U DIMM
Specification of ejector 3
B Counterbore type
V 35
Y 280 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2323 50 40 60 S V B N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

313
 High Rigidity Type
D & E Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

102
34

47

250
208

230
204
148
94

45
100
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin
Datum plane
4-M8 184
185

◆ High regidity type

Standard type P.380
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

314 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.380

■ How to order

■ Order example MDC DA 2325 40 40 70 S V B N OH 200 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 280
Futaba if there is any addition or
3
2
change to the specification.

X 350 U DIMM
Specification of ejector 5
B Counterbore type
V 35
Y 280 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2325 50 40 60 S V B N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

315
 High Rigidity Type
D & E Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

127
34

71

300
258

280
254
196
142

69
125
12 20
Return pin Guide pin

4-M14 68
20 90
Support pin
184 Datum plane
4-M8
185

◆ High regidity type

Standard type P.384
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

316 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.384

■ How to order

■ Order example MDC DA 2330 40 40 70 S V B N OH 200 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 280
Futaba if there is any addition or
3
3
change to the specification.

X 350 U DIMM
Specification of ejector 0
B Counterbore type
V 35
Y 280 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2330 50 40 60 S V B N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

317
 High Rigidity Type
D & E Series 2335
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

152
96
34

350
308

330
304
246
192

94
150
12 20
Return pin Guide pin

6-M14 68
20 90
Support pin
184 Datum plane
4-M8
185

◆ High regidity type

Standard type P.386
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 20 A 20 30
B A 20 30

Plate R
Plate R
Plate S
U

13
13

C
C

15
15

25
25

318 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.386

■ How to order

■ Order example MDC DA 2335 40 40 70 S V B N OH 200 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 IH
Installs support pins at the inner
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers. positions with bushings
e.g.:（100→ 10 ） Installs support pins at the inner
IN positions without bushings

Width of clamping
plate
Orientation of
guide This may be changed to J or P by 2
S 280
Futaba if there is any addition or
3
3
change to the specification.

X 350 U DIMM
Specification of ejector 5
B Counterbore type
V 35
Y 280 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2335 50 40 60 S V B N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DCtype DDtype
B 20 A 20 30
A 20 30

Plate R
Plate R
Plate S
B

13
13
C

15
15
25

25

319
 High Rigidity Type
D & E Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

97
34

33 35

250
200

230
194
130
70

15

95
25
Return pin Guide pin

4-M14 80
25 100
Support pin
194 Datum plane
4-M8
200

◆ High regidity type

Standard type P.390
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

320 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.390

■ How to order

■ Order example MDC DA 2525 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
25 30 35 40 50 60 OH
B DIMM 70 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 300
Futaba if there is any addition or
change to the specification. 5
2
X 350 U DIMM
B
Specification of ejector
Counterbore type
5
V 35
Y 300 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2525 50 40 70 S V B N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480 Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

321
 High Rigidity Type
D & E Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

122
34

60

300
250

280
244
180
120

58
120
15 25
Return pin
Guide pin

4-M14 80
25 100
Support pin
Datum plane
4-M8 194
200

◆ High regidity type

Standard type P.394
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

322 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.394

■ How to order

■ Order example MDC DA 2530 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
25 30 35 40 50 60 OH
B DIMM 70 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 300
Futaba if there is any addition or
change to the specification. 5
3
X 350 U DIMM
B
Specification of ejector
Counterbore type
0
V 35
Y 300 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2530 50 40 70 S V B N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480 Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

323
 High Rigidity Type
D & E Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
63 120 63
M16

147
34

85
300

330
294
230
170

350
83
145
15 25
Return pin
Guide pin

6-M14 80
25 100
Support pin
Datum plane
4-M8 194
200

◆ High regidity type

Standard type P.396
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

324 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.396

■ How to order

■ Order example MDC DA 2535 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
25 30 35 40 50 60 OH
B DIMM 70 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 300
Futaba if there is any addition or
change to the specification. 5
3
X 350 U DIMM
B
Specification of ejector
Counterbore type
5
V 35
Y 300 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2535 50 40 70 S V B N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

325
 High Rigidity Type
D & E Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350
TW
250
63 120 63
M16

172
110
34
350

380
344
280
220

400
108
170
15 25
Return pin Guide pin

6-M14 80
25 100
Support pin
Datum plane
4-M8 194
200

◆ High regidity type

Standard type P.398
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

326 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.398

■ How to order

■ Order example MDC DA 2540 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
25 30 35 40 50 60 OH
B DIMM 70 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 60 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 300
Futaba if there is any addition or
change to the specification. 5
4
X 350 U DIMM
B
Specification of ejector
Counterbore type
0
V 35
Y 300 D Spacer type
W 50
※ The order method (code) of this part is
Z 350 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2540 50 40 70 S V B N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

327
 High Rigidity Type
D & E Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

122
60
250
244
180
120

280
300
58
φ15

120
Return pin φ25
Guide pin

4-M14 90
φ25 110
Support pin

4-M8 214 Datum plane

215

◆ High regidity type

Standard type P.404
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

328 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.404

■ How to order

■ Order example MDC DA 2730 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
30 35 40 50 60 70 OH
B DIMM 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 320
Futaba if there is any addition or
change to the specification. 7
3
X 400 U DIMM
B
Specification of ejector
Counterbore type
0
V 40
Y 320 D Spacer type
W 50
※ The order method (code) of this part is
Z 400 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2730 50 40 70 S V B N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

329
 High Rigidity Type
D & E Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

147
85
300
294
230
170

330
350
83
145
φ15
Return pin φ25
Guide pin

6-M14 90
φ25 110
Support pin

4-M8 214 Datum plane

215

◆ High regidity type

Standard type P.406
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 25 A 25 35
B A 25 35

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

330 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.406

■ How to order

■ Order example MDC DA 2735 40 40 70 S V B N OH 210 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120
Specification of support pin
Installs support pins at the outer
30 35 40 50 60 70 OH
B DIMM 80 90 100 110 120 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 70 80 90 IH
Installs support pins at the inner
positions with bushings
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 2
S 320
Futaba if there is any addition or
change to the specification. 7
3
X 400 U DIMM
B
Specification of ejector
Counterbore type
5
V 40
Y 320 D Spacer type
W 50
※ The order method (code) of this part is
Z 400 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 2735 50 40 70 S V B N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 25 A 25 35
A 25 35

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

331
 High Rigidity Type
D & E Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

117
49
250
234
164

280
300
98

47
φ15
φ30

115
Return pin
Guide pin

4-M14 106
φ30 120
Support pin
Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.418
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 30 A 30 45
B A 30 45

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

332 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.418

■ How to order

■ Order example MDC DA 3030 50 50 80 S V B N OH 260 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
30 35 40 50 60 70 310 320 330 340 350 360
A DIMM 80 90 100 110 120 130
Specification of support pin
Installs support pins at the outer
30 35 40 50 60 70 OH
B DIMM 80 90 100 110 120 130 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 70 80 90 100 IH
Installs support pins at the inner
positions with bushings
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 3
S 350
Futaba if there is any addition or
change to the specification. 0
3
X 400 U DIMM
B
Specification of ejector
Counterbore type
0
V 45
Y 350 D Spacer type
W 60
※ The order method (code) of this part is
Z 400 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 3030 50 60 70 S V B N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 30 A 30 45
A 30 45

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

333
 High Rigidity Type
D & E Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

142
74
300
284
214
148

330
350
72
φ15

140
Return pin φ30
Guide pin

6-M14 106
φ30 120
Support pin
Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.422
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 30 A 30 45
B A 30 45

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

25
25

334 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.422

■ How to order

■ Order example MDC DA 3035 50 50 80 S V B N OH 260 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130
Specification of support pin
Installs support pins at the outer
35 40 50 60 70 80 OH
B DIMM 90 100 110 120 130 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 70 80 90 100 IH
Installs support pins at the inner
positions with bushings
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 3
S 350
Futaba if there is any addition or
change to the specification. 0
3
X 400 U DIMM
B
Specification of ejector
Counterbore type
5
V 45
Y 350 D Spacer type
W 60
※ The order method (code) of this part is
Z 400 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 3035 50 60 70 S V B N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 30 A 30 45
A 30 45

Plate R
Plate R
Plate S
B

15
15
C

20
20
25

25

335
 High Rigidity Type
D & E Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M20

167
99
350
334
264
198

380
400
97
165
φ15
Return pin φ30
Guide pin

6-M14 106
φ30 120
Support pin
Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.424
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype
B 30 A 30 45
B A 30 45

Plate R
Plate R
Plate S
U

15
15

C
C

20
20

30
30

336 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 STD Standard type P.424

■ How to order

■ Order example MDC DA 3040 50 50 80 S V B N OH 260 Option

DA DB DC DD
Type Length of support pin
EA EB EC ED
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130
Specification of support pin
Installs support pins at the outer
35 40 50 60 70 80 OH
B DIMM 90 100 110 120 130 position side with bushings

High Rigidity type

Installs support pins at the outer
ON positions without bushings
C DIMM 70 80 90 100 IH
Installs support pins at the inner
positions with bushings
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
Installs support pins at the inner
e.g.:（100→ 10 ） IN positions without bushings
Width of clamping Orientation of
plate guide This may be changed to J or P by 3
S 350
Futaba if there is any addition or
change to the specification. 0
4
X 400 U DIMM
B
Specification of ejector
Counterbore type
0
V 45
Y 350 D Spacer type
W 60
※ The order method (code) of this part is
Z 400 — Types without backing plate different from that of standard type.

■ How to order optional specification

■ Order example MDC DB 3040 50 60 70 S V B N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DCtype DDtype
B 30 A 30 45
A 30 45

Plate R
Plate R
Plate S
B

15
15
C

20
20
30

30

337
 D&E Series 1113

175
110
24 60 24

51
24

15 17
102

108
130
88
66
34

10 12

49
Return pin Guide pin

4-M8 30
12 46
Support pin
Datum plane
4-M5 82
90

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13

13

13
C

C
C
13

13
13
15
15

15

338 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 1113 25 25 50 X V M N OH 120 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
60 70 80 90 100 110

D & E series
3-Plate Type
Nominal dimension 120 150

20 25 30 35 40 50
A DIMM 60
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 40 50
positions without bushings
1
※ When selecting DE or DF without Plate C, specify 00.
IH
Installs support pins at the inner
positions with bushings 1
IN
Installs support pins at the inner 3
positions without bushings
Orientation of
guide
This may be changed to J or P by
Futaba if there is any addition or
X change to the specification.

U DIMM Specification of ejector

V 25 M Counterbore type

Z W 30 L Spacer type
— Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1113 30 25 40 X V M N OH 150 / S20 / #EH

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30 .

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 10 A 10 25

Plate R
B 10 A 10 25

B 10 A 10 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

C
13

15
15

15

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
339
 D&E Series 1313

175
130
24 80 24

51
24

15 17
102

108
130
34
66
88

49
10 12
Return pin Guide pin

4-M8 48
12 66
Support pin
Datum plane
4-M5 102
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13

13

13
C

C
C
13

13
13
15
15

15

340 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 1313 25 25 50 X V M N OH 120 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
60 70 80 90 100 110

D & E series
3-Plate Type
Nominal dimension 120 150

20 25 30 35 40 50
A DIMM 60
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 40 50
positions without bushings
Installs support pins at the inner
3
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 1
IN
Installs support pins at the inner
positions without bushings
3
Orientation of
guide
This may be changed to J or P by
Futaba if there is any addition or
X change to the specification.

U DIMM Specification of ejector

V 25 M Counterbore type

Z W 30 L Spacer type
— Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1313 30 25 40 X V M N OH 150 / S20 / #EH

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30 .

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 10 A 10 25

Plate R
B 10 A 10 25

B 10 A 10 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

C
13

15
15

15

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
341
 D&E Series 1315

175
130
24 80 24

61
24

27
122
108

128
150
86
54

25
59
10 12
Return pin Guide pin

4-M8 48
12 66
Support pin
Datum plane
4-M5 102
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13

13

13
C

C
C
13

13
13
15
15

15

342 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 1315 25 25 50 X V M N OH 120 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
60 70 80 90 100 110

D & E series
3-Plate Type
Nominal dimension 120 150

20 25 30 35 40 50
A DIMM 60
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 40 50
positions without bushings
Installs support pins at the inner
3
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 1
IN
Installs support pins at the inner
positions without bushings
5
Orientation of
guide
This may be changed to J or P by
Futaba if there is any addition or
X change to the specification.

U DIMM Specification of ejector

V 25 M Counterbore type

Z W 30 L Spacer type
— Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1315 30 25 40 X V M N OH 150 / S20 / #EH

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30 .

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 10 A 10 25

Plate R
B 10 A 10 25

B 10 A 10 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

C
13

15
15

15

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
343
 D&E Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

72
34

26

162
180
144
96
52

24
70
12 16
Return pin Guide pin

4-M10 48
16 72
Support pin
Datum plane
4-M6 114
120

High Regidity type P.288

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

344 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.288

■ How to order

■ Order example MDC DA 1518 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
5
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 1
IN
Installs support pins at the inner
positions without bushings
8
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 200 Futaba if there is any addition or
change to the specification.

X 230
U DIMM Specification of ejector
Y 200 V 30 M Counterbore type
W 40 L Spacer type
Z 230 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1518 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 25

Plate R
B 15 A 15 25

B 15 A 15 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
345
 D&E Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

82
34

36

200
182
164
116
72

34
16

80
12
Guide pin

Return pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120

High Regidity type P.290

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

346 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.290

■ How to order

■ Order example MDC DA 1520 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
5
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 200 Futaba if there is any addition or
change to the specification.

X 230
U DIMM Specification of ejector
Y 200 V 30 M Counterbore type
W 40 L Spacer type
Z 230 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1520 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 25

Plate R
B 15 A 15 25

B 15 A 15 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
347
 D&E Series 1523
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230
TW
150
28 90 28
M12

97
34

51
194
146
102

212
230
49
95
12 16
Return pin Guide pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120

High Regidity type P.292

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

348 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.292

■ How to order

■ Order example MDC DA 1523 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
5
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
3
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 200 Futaba if there is any addition or
change to the specification.

X 230
U DIMM Specification of ejector
Y 200 V 30 M Counterbore type
W 40 L Spacer type
Z 230 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1523 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 25

Plate R
B 15 A 15 25

B 15 A 15 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
349
 D&E Series 1525
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230
TW
150
28 90 28
M12

107
34

61

232
250
122
214
166

59
105
12 16
Return pin Guide pin

4-M10 48
16 72
Support pin
Datum plane
4-M6 114
120

High Regidity type P.294

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

350 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.294

■ How to order

■ Order example MDC DA 1525 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
5
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 200 Futaba if there is any addition or
change to the specification.

X 230
U DIMM Specification of ejector
Y 200 V 30 M Counterbore type
W 40 L Spacer type
Z 230 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1525 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 25

Plate R
B 15 A 15 25

B 15 A 15 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
351
 D&E Series 1530
TW Clamping plate spec. TW
Clamping type 200
150 Bolt-fastening type 230

28 90 28
M12

132
86
34
264
216
172

282
300
84
130
12 16
Return pin Guide pin

4-M10 48
16 72
Support pin
Datum plane
4-M6 114
120
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

352 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 1530 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
80 90 100 110 120 130

D & E series
3-Plate Type
Nominal dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
5
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 3
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 200 Futaba if there is any addition or
change to the specification.

X 230
U DIMM Specification of ejector
Y 200 V 30 M Counterbore type
W 40 L Spacer type
Z 230 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1530 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 25

Plate R
B 15 A 15 25

B 15 A 15 25

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
353
 D&E Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

34

77
21 23
158
154

180
200
98
46

75
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin
Datum plane
4-M8 140
145

High Regidity type P.296

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

354 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.296

■ How to order

■ Order example MDC DA 1820 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
8
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 230 Futaba if there is any addition or
change to the specification.

X 280
U DIMM Specification of ejector
Y 230 V 30 M Counterbore type
W 40 L Spacer type
Z 280 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1820 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 30

Plate R
B 15 A 15 30

B 15 A 15 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
355
 D&E Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

92
34

38
188
184
128

210
230
76

36
90
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin
Datum plane
4-M8 140
145

High Regidity type P.298

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

356 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.298

■ How to order

■ Order example MDC DA 1823 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
8
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
3
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 230 Futaba if there is any addition or
change to the specification.

X 280
U DIMM Specification of ejector
Y 230 V 30 M Counterbore type
W 40 L Spacer type
Z 280 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1823 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 30

Plate R
B 15 A 15 30

B 15 A 15 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
357
 D&E Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

102
34

48

230
250
208
204
148
96

46
100
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin
Datum plane
4-M8 140
145

High Regidity type P.300

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

358 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.300

■ How to order

■ Order example MDC DA 1825 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
8
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 2
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 230 Futaba if there is any addition or
change to the specification.

X 280
U DIMM Specification of ejector
Y 230 V 30 M Counterbore type
W 40 L Spacer type
Z 280 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1825 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 30

Plate R
B 15 A 15 30

B 15 A 15 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
359
 D&E Series 1830
Clamping plate spec. TW
Clamping type 230
TW Bolt-fastening type 280

180
33 110 33
M12

127
34

73

280
300
254
198
258

146

71
125
12 20
Return pin Guide pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Regidity type P.302

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

360 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.302

■ How to order

■ Order example MDC DA 1830 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
8
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 3
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 230 Futaba if there is any addition or
change to the specification.

X 280
U DIMM Specification of ejector
Y 230 V 30 M Counterbore type
W 40 L Spacer type
Z 280 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1830 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 30

Plate R
B 15 A 15 30

B 15 A 15 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
361
 D&E Series 1835
TW Clamping plate spec. TW
Clamping type 230
180 Bolt-fastening type 280
33 110 33
M12

152
98
34

330
350
308
304
248
196

96
12 20 150
Return pin Guide pin

6-M12 68
20 90
Support pin Datum plane
4-M8 140
145
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

13
C

15
15

15

20
20

20

362 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 1835 30 30 60 S V M N OH 160 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 OH position side with bushings

ON
Installs support pins at the outer 1
C DIMM 50 60 70 80
positions without bushings
Installs support pins at the inner
8
※ When selecting DE or DF without Plate C, specify 00.
IH positions with bushings 3
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
S 230 Futaba if there is any addition or
change to the specification.

X 280
U DIMM Specification of ejector
Y 230 V 30 M Counterbore type
W 40 L Spacer type
Z 280 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 1835 40 30 50 S V M N OH 180 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 15 A 15 30

Plate R
B 15 A 15 30

B 15 A 15 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

15
20

20

20

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
363
 D&E Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

34

77
21 23

180
200
154
150
98
46

12 20

75
Return pin Guide pin

4-M12 84
20 100
Support pin
Datum plane
4-M8 154
160

High Rigidity type P.304

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

13
13

13
C

15
15

15
25

25
25

364 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.304

■ How to order

■ Order example MDC DA 2020 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2020 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
13

C
C

C
15

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
365
 D&E Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

92
34

38
184
180
128

210
230
76

36
15 20

90
Return pin Guide pin

4-M12 80
20 100
Support pin Datum plane
4-M8 154
160

High Rigidity type P.306

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

366 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.306

■ How to order

■ Order example MDC DA 2023 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
3
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2023 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
367
 D&E Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

102
34

48

230
250
204
200
148
96

46
100
15 20
Return pin Guide pin

4-M12 80
20 100
Support pin Datum plane
4-M8 154
160

High Rigidity type P.308

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

368 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.308

■ How to order

■ Order example MDC DA 2025 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2025 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
369
 D&E Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

127
34

73
254
250
198
146

280
300
71
125
15 20
Return pin Guide pin

6-M12 80
20 100
Support pin
Datum plane
4-M8 154
160

High Rigidity type P.310

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

370 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.310

■ How to order

■ Order example MDC DA 2030 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 3
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2030 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
371
 D&E Series 2035
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

152
98
34
304
300
248
196

330
350
96
150
15 20
Return pin Guide pin

6-M12 80
20 100
Support pin Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

372 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2035 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 3
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2035 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
373
 D&E Series 2040
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 250
50 or more Ｍ16 TW Bolt-fastening type 280

200
38 120 38
FK

177
123
34
354
350
298
246

380
400
121
175
15 20
Return pin Guide pin

6-M12 80
20 100
Support pin Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

374 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2040 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 4
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2040 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
375
 D&E Series 2045
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12
TW Clamping type 250
50 or more Ｍ16 200 Bolt-fastening type 280

38 120 38
FK

202
148
34
404
400
348
296

430
450
146
200
15 20
Return pin
Guide pin

6-M12 80
20 100
Support pin Datum plane
4-M8 154
160
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

376 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2045 30 30 60 S V M N OH 170 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100
Specification of support pin
20 25 30 35 40 50 Installs support pins at the outer
B DIMM 60 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 50 60 70 80 90
positions without bushings
Installs support pins at the inner 0
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 4
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 250 change to the specification.

X 280 U DIMM Specification of ejector

V 30 M Counterbore type
Y 250 W 40 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 280

■ How to order optional specification

■ Order example MDC DB 2045 40 30 50 S V M N OH 190 / S30 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
377
 D&E Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

92
34

37

210
230
184
180
128
74

35
15 20

90
Return pin Guide pin

4-M12 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.312

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

378 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.312

■ How to order

■ Order example MDC DA 2323 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
3
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2323 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
379
 D&E Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

102
34

47
204
200
148

230
250
94

45
100
15 20
Return pin Guide pin

4-M12 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.314

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

380 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.314

■ How to order

■ Order example MDC DA 2325 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2325 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
381
 D&E Series 2327
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

112
34

56

250
270
224
220
166
112

54
110
15 20
Return pin Guide pin

4-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

382 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2327 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 2
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
7
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2327 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
383
 D&E Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

127
34

71

280
300
254
250
196
142

69
125
15 20
Return pin Guide pin

4-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.316

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

384 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.316

■ How to order

■ Order example MDC DA 2330 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 3
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2330 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B Refer to the separate volume“Additional Mold Base
change ※ Details ☞ P.480 processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
385
 D&E Series 2335
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

152
96
34
304
300
246
192

330
350
94
150
15 20
Return pin Guide pin

6-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.318

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

386 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.318

■ How to order

■ Order example MDC DA 2335 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 3
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2335 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
387
 D&E Series 2340
Clamping plate spec. TW
Clamping type 280
TW Bolt-fastening type 350

230
43 140 43
M16

177
121
34
354
350
296
242

380
400
119

  
15 20 175
Return pin Guide pin

6-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

388 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2340 40 40 70 S V M N OH 200 Option

DA DB DC DD DE DF
Type Length of support pin
EA EB EC ED
90 100 110 120 130 140

D & E series
3-Plate Type
Nominal dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100
Specification of support pin
25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
IH positions with bushings 4
e.g.:（100→ 10 ）
※ When selecting DE or DF without Plate C, specify 00.
IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide This may be changed to J or P by
Futaba if there is any addition or
S 280 change to the specification.

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 280 W 50 L Spacer type
— Types without backing plate — When selecting DE or DF type
Z 350

■ How to order optional specification

■ Order example MDC DB 2340 50 40 60 S V M N OH 240 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

DDtype DEtype DFtype

B 20 A 20 30

Plate R
B 20 A 20 30

B 20 A 20 30

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
389
 D&E Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

97
34

33 35
200
194
130

230
250
70

15 25

95
Return pin Guide pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.320

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

390 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.320

■ How to order

■ Order example MDC DA 2525 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 2
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2525 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480 Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
391
 D&E Series 2527
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

107
34

45

250
270
220
214
150
90

43
105
15 25
Return pin Guide pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

392 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2527 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 2
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
7
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2527 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480 Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
393
 D&E Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

122
34

60
250
244
180
120

280
300
58
120
15 25
Return pin Guide pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.322

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

394 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.322

■ How to order

■ Order example MDC DA 2530 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2530 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.480 Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
395
 D&E Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
48 150 48
M16

147
34

85
298
294
230
170

330
350
83
145
  20  25
Return pin Guide pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.324

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

396 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.324

■ How to order

■ Order example MDC DA 2535 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2535 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
397
 D&E Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350
TW
250
48 150 48
M16

172
110
34
348
344
280
220

380
400
108
170
20 25
Return pin Guide pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.326

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

398 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.326

■ How to order

■ Order example MDC DA 2540 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2540 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
399
 D&E Series 2545
Clamping plate spec. TW
Clamping type 300
TW Bolt-fastening type 350

250
48 150 48
M16

197
135
34
398
394
330
270

430
450
133
20 25 195
Return pin Guide pin

6-M14 102
25 130
Support pin Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

400 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2545 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2545 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
401
 D&E Series 2550
Clamping plate spec. TW
TW Clamping type 300
250 Bolt-fastening type 350

48 150 48
M16

222
160
34
448
444
380
320

480
500
158
220
25
20 Guide pin
Return pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

402 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2550 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120 280 290 300 320

Specification of support pin

25 30 35 40 50 60 Installs support pins at the outer
B DIMM 70 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 60 70 80 90 100
IH
positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 300
change to the specification.

X 350
U DIMM Specification of ejector
V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2550 50 40 70 S V M N OH 240 / R20 / S40 / #FK / #EH

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
※ For DE & DF type, ejector rod hole will not be machined.
403
 D&E Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

122
60
244
240
180
120

276
300
58
120
20 25
Return pin Guide pin

4-M14 114
25 136
Support pin
Datum plane
4-M10 214
215

High Rigidity type P.328

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

404 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.328

■ How to order

■ Order example MDC DA 2730 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 7
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 320
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2730 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
405
 D&E Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

147
85
294
290
230

326
350
170

83
145
20 25
Return pin Guide pin

6-M14 114
25 136
Support pin
Datum plane
4-M10 214
215

High Rigidity type P.330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

406 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.330

■ How to order

■ Order example MDC DA 2735 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 7
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 320
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2735 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
407
 D&E Series 2740
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400
TW
270
53 160 53
M16

172
110
344
340
280

376
400
220

108
170
20 25
Return pin Guide pin

6-M14 114
25 136
Support pin
Datum plane
4-M10 214
215

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

408 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2740 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 7
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 320
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2740 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
409
 D&E Series 2750
B DIMM FK Clamping plate spec. TW
70 or less Ｍ16
TW Clamping type 320
80 or more Ｍ20 270 Bolt-fastening type 400

53 160 53
FK

222
160
444
440
380

476
500
320

158
220
20 25
Return pin Guide pin

6-M14 114
25 136
Support pin
Datum plane
4-M10 214
215

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

15
15

15
C

20
20

20
25

25
25

410 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2750 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 7
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 320
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2750 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
15

C
C

C
20

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
411
 D&E Series 2930
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

122
60

276
300
244
240
180
120

58
120
20 25
Return pin Guide pin

4-M14 134
25 156
Support pin
Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

20
20

20
C

25
25

25
25

25
25

412 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2930 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 9
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 350
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2930 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
20

C
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
413
 D&E Series 2935
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

147
85

326
350
294
290
230
170

83
145
20 25
Return pin Guide pin

6-M14 134
25 156
Support pin
Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

20
20

20
C

25
25

25
25

25
25

414 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2935 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 9
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 350
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2935 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
20

C
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
415
 D&E Series 2940
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

172
110

376
400
344
340
280
220

108
170
20 25
Return pin Guide pin

6-M14 134
25 156
Support pin
Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U
U

20
20

20
C

25
25

25
25

25
25

416 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 2940 40 40 70 S V M N OH 210 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
100 110 120 130 140 150

D & E series
3-Plate Type
Nominal dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70
A DIMM 80 90 100 110 120 280 290 300 320

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 OH position side with bushings

ON
Installs support pins at the outer 2
C DIMM 70 80 90 100 positions without bushings
Installs support pins at the inner 9
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 40 M Counterbore type
Y 350
W 50 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 2940 50 40 70 S V M N OH 240 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 25 A 25 35

Plate R
B 25 A 25 35

B 25 A 25 35

Plate R Plate R
Plate S
Plate S Plate S
U
20

C
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
417
 D&E Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

117
49
240
234
164

276
300
98

47
115
20 30
Return pin Guide pin

4-M14 134
30 156
Support pin
Datum plane
4-M10 234
240

High Rigidity type P.332

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

25
25
25

418 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.332

■ How to order

■ Order example MDC DA 3030 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
30 35 40 50 60 70
A DIMM 80 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

30 35 40 50 60 70 Installs support pins at the outer
B DIMM 80 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3030 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
419
 D&E Series 3032
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

127
59

296
320
260
254
184
118

57
125
20 30
Return pin Guide pin

4-M14 134
30 156
Support pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

25
25
25

420 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3032 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
2
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3032 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
421
 D&E Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

142
74

326
350
290
284
214
148

72
140
20 30
Return pin Guide pin

6-M14 134
30 156
Support pin
Datum plane
4-M10 234
240

High Rigidity type P.334

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

25
25
25

422 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.334

■ How to order

■ Order example MDC DA 3035 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3035 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

25
25

25

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
423
 D&E Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M20

167
99

376
400
340
334
264
198

97
165
20 30
Return pin Guide pin

6-M14 134
30 156
Support pin
Datum plane
4-M10 234
240

High Rigidity type P.336

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

424 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787 HR High Rigidity type P.336

■ How to order

■ Order example MDC DA 3040 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3040 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
425
 D&E Series 3045
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400
TW
300
58 180 58
M20

192
122
390
384
312
244

426
450
120
190
25 30
Return pin Guide pin

6-M16 128
30 156
Support pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

426 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3045 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3045 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
427
 D&E Series 3050
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400
TW
300
58 180 58
M20

217
147
440
434
362
294

476
500
145
25 30 215
Return pin Guide pin

6-M16 128
30 156
Support pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

428 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3050 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3050 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
429
 D&E Series 3055
Clamping plate spec. TW
TW Clamping type 350
Bolt-fastening type 400
300
58 180 58
M24

242
172
490
484
412
344

526
550
170
240
25 30
Return pin Guide pin

6-M16 128
30 156
Support pin
Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

430 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3055 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3055 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
431
 D&E Series 3060
TW Clamping plate spec. TW
300 Clamping type 350
Bolt-fastening type 400
58 180 58
M24

267
197
540
534
462
394

576
600
195
265
25 30
Return pin Guide pin

6-M16 128
30 156
Support pin
Datum plane
4-M10 234
240
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

432 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3060 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 6
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 350
change to the specification.

X 400
U DIMM Specification of ejector
V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3060 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
433
 D&E Series 3335
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

142
74
290
284
214

326
350
148

72
140
25 30
Return pin Guide pin

6-M14 154
30 186
Support pin Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

434 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3335 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3335 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
435
 D&E Series 3340
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

167
99
340
334
264

376
400
198

97
165
25 30
Return pin Guide pin

6-M14 154
30 186
Support pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

436 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3340 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3340 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
437
 D&E Series 3345
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550
TW
330
58 210 58
M20

192
122
390
384
312

426
450
244

120
190
25 30
Return pin Guide pin

6-M16 154
30 186
Support pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

438 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3345 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3345 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
439
 D&E Series 3350
Clamping plate spec. TW
Clamping type 400
TW Bolt-fastening type 550

330
58 210 58
M24

217
147

476
500
440
434
362
294

145
215
25 30
Return pin Guide pin

6-M16 154
30 186
Support pin
Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

440 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3350 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80
A DIMM 90 100 110 120 130 310 320 330 340 350 360

Specification of support pin

35 40 50 60 70 80 Installs support pins at the outer
B DIMM 90 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 3
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3350 50 60 70 S V M N OH 280 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 30 A 30 45

Plate R
B 30 A 30 45

B 30 A 30 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
441
 D&E Series 3535
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

142
72
290
284
212
144

326
350
70
140
25 30
Return pin Guide pin

6-M16 164
30 196
Support pin Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

442 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3535 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90
A DIMM 100 110 120 130 310 320 330 340 350 360

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 3
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3535 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 45

Plate R
B 35 A 35 45

B 35 A 35 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
443
 D&E Series 3540
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

167
97

376
400
340
334
262
194

95
165
25 30
Return pin Guide pin

6-M16 164
30 196
Support pin
Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

444 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3540 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90
A DIMM 100 110 120 130 310 320 330 340 350 360

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3540 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 45

Plate R
B 35 A 35 45

B 35 A 35 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
445
 D&E Series 3545
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M24

192
122

426
450
390
384
312
244

120
190
25 30
Return pin Guide pin

6-M16 164
30 196
Support pin
Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

446 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3545 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
130 140 150 160 170 180

D & E series
3-Plate Type
Nominal dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90
A DIMM 100 110 120 130 310 320 330 340 350 360

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3545 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 45

Plate R
B 35 A 35 45

B 35 A 35 45

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
447
 D&E Series 3550
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550
TW
350
63 220 63
M24

212
134

476
500
440
424
344
268

132
210
25 35
Return pin Guide pin

6-M16 152
35 196
Support pin
Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

448 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3550 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110
IH
positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3550 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
449
 D&E Series 3555
Clamping plate spec. TW
TW Clamping type 400
Bolt-fastening type 550
350
63 220 63
M24

237
159

526
550
490
474
394
318

157
25
Return pin
35
Guide pin 235

6-M16 152
35 196
Support pin
Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

450 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3555 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110
IH
positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3555 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
451
 D&E Series 3560
TW Clamping plate spec. TW
350 Clamping type 400
Bolt-fastening type 550
63 220 63
M24

262
184
540
524
444
368

576
600
182
25 35 260
Return pin Guide pin

6-M16 152
35 196
Support pin
Datum plane
4-M10 274
285
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

20
20

20
C

25
25

25

30
30
30

452 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 3560 50 50 80 S V M N OH 260 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 OH position side with bushings

ON
Installs support pins at the outer 3
C DIMM 70 80 90 100 110 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 6
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 400
change to the specification.

X 550
U DIMM Specification of ejector
V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 3560 50 60 70 S V M N OH 280 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
U
20
C

C
25

30
30

30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
453
 D&E Series 4040
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

162
84

374
400
340
324
244
168

82
160
25 35
Return pin Guide pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U
U

25

25
25
C

30
30

30

30
30
30

454 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4040 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4040 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
U
25
C

C
30
30

30
30

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
455
 D&E Series 4045
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

187
109
390
374
294
218

424
450
107
185
25 35
Return pin Guide pin

6-M16 198
35 234
Support pin
Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U
U

25

25
25
C

30
30

30

35
35
35

456 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4045 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4045 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
U
25
C

C
30
35

35
35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
457
 D&E Series 4050
HT DIMM FK Clamping plate spec. TW
80～365 Ｍ24 Clamping type 450
370～465 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

212
134

474
500
440
424
344
268

132
210
25 35
Return pin Guide pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
A 35 50

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

458 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4050 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4050 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
459
 D&E Series 4055
HT DIMM FK Clamping plate spec. TW
80～310 Ｍ24 Clamping type 450
315～465 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

237
159

524
550
490
474
394
318

157
235
25 35
Return pin Guide pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
A 35 50

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

460 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4055 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4055 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
461
 D&E Series 4060
HT DIMM FK Clamping plate spec. TW
80～265 Ｍ24 Clamping type 450
270～465 Ｍ30 Bolt-fastening type 550
TW
400
68 260 68
FK

262
184
540
524
444
368

574
600
182
25
Return pin
35
Guide pin
260

6-M16 198
35 234 Datum plane
Support pin

4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
A 35 50

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

462 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4060 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 6
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4060 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
463
 D&E Series 4070
HT DIMM FK Clamping plate spec. TW
80～195 Ｍ24 TW Clamping type 450
200～465 Ｍ30 400 Bolt-fastening type 550

68 260 68
FK

312
234
640
624
544
468

674
700
232
310
25 35
Return pin Guide pin

6-M16 198
35 234
Support pin
Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 35 A 35 50
B A 35 50

Plate R
A 35 50

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

464 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4070 70 70 10 S V M N OH 330 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
160 170 180 190 200 210

D & E series
3-Plate Type
Nominal dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 340 350 360 380 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 7
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 450
change to the specification.

X 550
U DIMM Specification of ejector
V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4070 80 60 10 S V M N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 35 A 35 50

Plate R
B 35 A 35 50

B 35 A 35 50

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
465
 D&E Series 4545
HT DIMM FK Clamping plate spec. TW
80～360 Ｍ24 Clamping type 500
365～480 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

182
97
384
364
276
194

424
450
95
180
30 40
Return pin Guide pin

6-M16 226
40 264
Support pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

466 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4545 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 4
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
J 500
change to the specification.

S 550
U DIMM Specification of ejector
V 60 M Counterbore type
K 500
W 80 L Spacer type

Y 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4545 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT
HT

HT
U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
467
 D&E Series 4550
HT DIMM FK Clamping plate spec. TW
80～300 Ｍ24 Clamping type 500
305～480 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

207
122

474
500
434
414
326
244

120
205
30 40
Return pin Guide pin

6-M16 226
40 264
Support pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

468 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4550 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130
IH
positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
J 500
change to the specification.

S 550
U DIMM Specification of ejector
V 60 M Counterbore type
K 500
W 80 L Spacer type

Y 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4550 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT
HT

HT
U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
469
 D&E Series 4555
HT DIMM FK Clamping plate spec. TW
80～250 Ｍ24 Clamping type 500
255～480 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

232
147
484
464
376
294

524
550
145
230
30 40
Guide pin
Return pin

6-M16 226
40 264
Support pin Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

470 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4555 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130
IH
positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
5
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
J 500
change to the specification.

S 550
U DIMM Specification of ejector
V 60 M Counterbore type
K 500
W 80 L Spacer type

Y 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4555 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT
HT

HT
U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
471
 D&E Series 4560
HT DIMM FK Clamping plate spec. TW
80～210 Ｍ24 Clamping type 500
215～480 Ｍ30 Bolt-fastening type 550
TW
450
78 290 78
FK

257
172
344

574
534
514
426

600
170
255
30 40
Return pin Guide pin

6-M16 226
40 264
Support pin
Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

472 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 4560 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 4
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 5
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 6
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
J 500
change to the specification.

S 550
U DIMM Specification of ejector
V 60 M Counterbore type
K 500
W 80 L Spacer type

Y 550 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 4560 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT
HT

HT
U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
473
 D&E Series 5050
HT DIMM FK Clamping plate spec. TW
80～220 Ｍ24 Clamping type 600
225～480 Ｍ30 Bolt-fastening type 700

TW
500
88 320 88
FK

207
122

474
434
414
326
244

500
120
205
30 40
Return pin Guide pin

6-M16 256
40 294
Support pin
Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

474 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 5050 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 5
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 5
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 600
change to the specification.

X 700
U DIMM Specification of ejector
V 60 M Counterbore type
Y 600
W 80 L Spacer type

Z 700 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 5050 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
475
 D&E Series 5060
HT DIMM FK Clamping plate spec. TW
80～380 Ｍ30 Clamping type 600
385～480 Ｍ36 Bolt-fastening type 700

TW
500
88 320 88
FK

257
172
534
514
426

574
600
344

170
255
30 40
Return pin Guide pin

6-M16 256
40 294
Support pin
Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

476 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 5060 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 5
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 6
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 600
change to the specification.

X 700
U DIMM Specification of ejector
V 60 M Counterbore type
Y 600
W 80 L Spacer type

Z 700 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 5060 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
477
 D&E Series 5070
HT DIMM FK Clamping plate spec. TW
80～280 Ｍ30 Clamping type 600
285～480 Ｍ36 Bolt-fastening type 700
● The dimension of Plate A or Plate
B is 40, M30 is applied for FK.
TW
500
88 320 88
FK

307
222

674
700
634
614
526
444

220
305
30 40
Return pin Guide pin

6-M16 256
40 294
Support pin Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

DAtype DBtype DCtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT

HT
B
U

U
25

25

25
C

C
C

30
30

30
35

35
35

478 ※E series DA, DB, DC and DD types without the runner stripper plate will become EA, EB, EC and ED types respectively
TD Technical Data P.787

■ How to order

■ Order example MDC DA 5070 70 70 10 S V M N OH 350 Option

DA DB DC DD DE DF
Type
EA EB EC ED Length of support pin
200 210 220 230 240 250

D & E series
3-Plate Type
Nominal dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90
A DIMM 100 110 120 130 140 150 400

Specification of support pin

40 50 60 70 80 90 Installs support pins at the outer
B DIMM 100 110 120 130 140 150 OH position side with bushings

ON
Installs support pins at the outer 5
C DIMM 100 110 120 130 positions without bushings
Installs support pins at the inner 0
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
IH positions with bushings 7
※ When selecting DE or DF without Plate C, specify 00. IN
Installs support pins at the inner
positions without bushings
0
Width of clamping Orientation of
plate guide
This may be changed to J or P by
Futaba if there is any addition or
S 600
change to the specification.

X 700
U DIMM Specification of ejector
V 60 M Counterbore type
Y 600
W 80 L Spacer type

Z 700 — Types without backing plate — When selecting DE or DF type

■ How to order optional specification

■ Order example MDC DB 5070 80 60 10 S V M N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
Removes the threaded holes for eye bolts for Plate
#FK A and B Specifications other than the above are also available.
Additional
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

DDtype DEtype DFtype

B 40 A 40 60

Plate R
B 40 A 40 60

B 40 A 40 60

Plate R Plate R
Plate S
Plate S Plate S
HT

HT
HT

U
25
C

C
C
30
35

35

35

※ DE and DF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
479
 D&E Series Material Change Option

DAtype DBtype DCtype

Plate R
Plate R Plate A
Plate A Plate R
Plate S
Plate A
Plate B Plate B
Plate B

DDtype DEtype DFtype

Plate R
Plate R Plate A Plate R
Plate A Plate S Plate A
Plate S Plate B Plate S
Plate B Plate B

※ E series can be specified such as D series.

■ How to order material change specification

■ Order example MDC DB 1518 40 30 50 S V M N OH 170 / F – ASB

Material changing plate code

R Runner plate
A Cavity plate (fixed half)
S Stripper plate
Mold base order code
When ordering, specify the mold
B Cavity plate (moving half)
base specification with codes shown Following the － symbol, specify the
in each page. material changing plate. The plate of
which material can be changed are the
above four types, Plate R, A, S and B.

◆How to order Material designation code

In addition to the mold base order codes, please specify F HPM1
“Material designation code”and“Material changing K NAK55
plate code” . R NAK80

480
TD Technical Data P.787

Mold base nominal

Material designation code Material name Plate A thickness Plate B thickness Plate R thicknes Plate S thickness
dimension
1518
1520
1523
15 15 20 30 40
1820 20 25 30 35 40 20 25 30 35 40
1823
1825

D & E series
3-Plate Type
2020
F HPM1 2023
20 30 40
K NAK55 2025 25 30 35 40 25 30 35 40
R NAK80 2030
20
2323
2325
20 30 40 50
2327 25 30 35 40 50 25 30 35 40 50
2330

Material Change Option

2525
2527 20 25 25 30 40 50
30 35 40 50 30 35 40 50
2530
※ Product of materials and sizes not listed above will also be made to order. Please consult our sales office.

481
482
 THREE-PLATE TYPE F・G-SERIES
3-Plate Type
F & G series
■Structure and Component Name ・・・・・・・・・・・・・・・・・・・・・・・ P.484

■High Rigidity Type F & G Series

  1515∼1830 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.486∼505

  2020∼2540 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.506∼529
  2730∼3040 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.530∼539

■F & G Series

  1113∼1835 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.540∼569

  2020∼2340 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.570∼595
  2525∼2940 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.596∼623
  3030∼3555 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.624∼651
  4040∼4560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.652∼667
  5050∼5070 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.668∼673

■F & G Series Material Change Option ・・・・・・・・・・・・・・・・・・・・ P.674

 F&G Series Structure & Component Name

Hexagon socket head cap screw Threaded hole for eye bolt

Support pin & guide bushing

Hexagon socket head cap screw

Hole for ejector rod

Return pin

T Top clamping plate

R Runner plate GBB Guide bushing

A Cavity plate (fixed half)

GBA Guide bushing

B Cavity plate (moving half)

U Backing plate SPN Support pin

C Spacer block RPN Return pin

E Ejector retainer plate

F Ejector base plate

L Bottom clamping plate

This diagram shows FA type as a representative example.

484
FAType FFType
Stripper plate ejection type, which is actuated
Ejector pin ejection type
by mold opening behavior, without backing plate

T T
R GBB R GBB
A A GBA
GBA
B S GBB

U SPN B GBA

C RPN SPN

E C

F & G series
3-Plate Type
F
L L

FCType GAType
Ejector pin ejection type without backing
Ejector pin ejection type without runner plate
plate

Structure and Component Name

T T
R GBB A
A GBA
GBA B

B U SPN
SPN
C C RPN
E RPN E
F F
L L

FEType GCType
Stripper plate ejection type, which is actuated Ejector pin ejection type without runner plate
by mold opening behavior and backing plate

T
R GBB
A GBA
T
S GBB
A
B GBA GBA

U SPN B

C SPN
C RPN
E
F
L L

485
 High Rigidity Type
F & G Series 1515
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

34

57
132
150
114
66

55
12
Return pin

4-M10 28
16 52
Support pin

4-M6 114 Datum plane

120

◆ High regidity type

Standard type P.546
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 25

A 15 25

Plate R
Plate R
B
U

13

13
C
C

15

15
20

20

486
TD Technical Data P.787 STD Standard type P.546

■ How to order

■ Order example MDC FA 1515 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 200

High Rigidity type

B Counterbore type
X 230 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
5
1
■ How to order optional specification
5
■ Order example MDC FA 1515 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 25

A 25
B
U

13

13
C
C

15

15
20

20

487
 High Rigidity Type
F & G Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

72
34

162
144

180
96

70
12
Return pin

4-M10 28
16 52
Support pin

4-M6 114 Datum plane

120

◆ High regidity type

Standard type P.548
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 25

A 15 25

Plate R
Plate R
B
U

13

13
C
C

15

15
20

20

488
TD Technical Data P.787 STD Standard type P.548

■ How to order

■ Order example MDC FA 1518 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 200

High Rigidity type

B Counterbore type
X 230 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
5
1
■ How to order optional specification
8
■ Order example MDC FA 1518 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 25

A 25
B
U

13

13
C
C

15

15
20

20

489
 High Rigidity Type
F & G Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
38 70 38
M12

82
34

182
200
164
116

80
12
Return pin

4-M10 28
16 52
Support pin

4-M6 114 Datum plane

120

◆ High regidity type

Standard type P.550
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 25

A 15 25

Plate R
Plate R
B
U

13

13
C
C

15

15
20

20

490
TD Technical Data P.787 STD Standard type P.550

■ How to order

■ Order example MDC FA 1520 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 200

High Rigidity type

B Counterbore type
X 230 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
5
2
■ How to order optional specification 0
■ Order example MDC FA 1520 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 25

A 25
B
U

13

13
C
C

15

15
20

20

491
 High Rigidity Type
F & G Series 1523
Clamping plate spec. TW
Clamping type 200

TW Bolt-fastening type 230

150
38 70 38
M12

97
34

212
230
146
194

95
12
Return pin

4-M10 28
16 52
Support pin

4-M6 114 Datum plane

120

◆ High regidity type

Standard type P.552
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 25

A 15 25

Plate R
Plate R
B
U

13

13
C
C

15

15
20

20

492
TD Technical Data P.787 STD Standard type P.552

■ How to order

■ Order example MDC FA 1523 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 200

High Rigidity type

B Counterbore type
X 230 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
5
2
■ How to order optional specification 3
■ Order example MDC FA 1523 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 25

A 25
B
U

13

13
C
C

15

15
20

20

493
 High Rigidity Type
F & G Series 1525
Clamping plate spec. TW
TW Clamping type 200
Bolt-fastening type 230
150
38 70 38
M12

107
34

250
232
214
166

12
Return pin 105

4-M10 28
16 52
Support pin

4-M6 114 Datum plane

120

◆ High regidity type

Standard type P.554
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 25

A 15 25

Plate R
Plate R
B
U

13

13
C
C

15

15
20

20

494
TD Technical Data P.787 STD Standard type P.554

■ How to order

■ Order example MDC FA 1525 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 200

High Rigidity type

B Counterbore type
X 230 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
5
2
■ How to order optional specification 5
■ Order example MDC FA 1525 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

GAtype GCtype
B A 25

A 25
B
U

13

13
C
C

15

15
20

20

495
 High Rigidity Type
F & G Series 1818
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

34

67

180
134
144

162
78

65
12
Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.558
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 30

A 15 30

Plate R
Plate R
B
U

13

13
C

C
15

15
20

20

496
TD Technical Data P.787 STD Standard type P.558

■ How to order

■ Order example MDC FA 1818 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 230

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
8
1
■ How to order optional specification
8
■ Order example MDC FA 1818 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
20

20

497
 High Rigidity Type
F & G Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

34

77
154
164

182
200
98

75
12
Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.560
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 30

A 15 30

Plate R
Plate R
B
U

13

13
C

C
15

15
20

20

498
TD Technical Data P.787 STD Standard type P.560

■ How to order

■ Order example MDC FA 1820 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 230

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
8
2
■ How to order optional specification 0
■ Order example MDC FA 1820 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
20

20

499
 High Rigidity Type
F & G Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
43 90 43
M12

92
34
194

230
184
128

212
90
12
Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.562
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 30

A 15 30

Plate R
Plate R
B
U

13

13
C

C
15

15
20

20

500
TD Technical Data P.787 STD Standard type P.562

■ How to order

■ Order example MDC FA 1823 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 230

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
8
2
■ How to order optional specification 3
■ Order example MDC FA 1823 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
20

20

501
 High Rigidity Type
F & G Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280
TW
180
43 90 43
M12

102
34

232
250
204
148
214

100
12
Return pin

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.564
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 30

A 15 30

Plate R
Plate R
B
U

13

13
C

C
15

15
20

20

502
TD Technical Data P.787 STD Standard type P.564

■ How to order

■ Order example MDC FA 1825 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 230

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
8
2
■ How to order optional specification 5
■ Order example MDC FA 1825 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
20

20

503
 High Rigidity Type
F & G Series 1830
Clamping plate spec. TW
TW Clamping type 230
Bolt-fastening type 280
180
43 90 43
M12

127
34
264
254
198

282
300
12
Return pin
125

4-M12 48
20 72
Support pin

4-M6 140 Datum plane

145

◆ High regidity type

Standard type P.566
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 15 30

A 15 30

Plate R
Plate R
B
U

13

13
C

C
15

15
20

20

504
TD Technical Data P.787 STD Standard type P.566

■ How to order

■ Order example MDC FA 1830 30 30 60 S V B N OH 180 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70

Width of clamping
Specification of ejector
S 230

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 1
8
3
■ How to order optional specification 0
■ Order example MDC FA 1830 40 30 50 S V B N OH 190 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
20

20

505
 High Rigidity Type
F & G Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

34

77
154
164

200
182
98

75
12
Return pin

4-M12 48
20 72
Support pin

4-M6 154 Datum plane

160

◆ High regidity type

Standard type P.570
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

506
TD Technical Data P.787 STD Standard type P.570

■ How to order

■ Order example MDC FA 2020 30 30 60 S V B N OH 190 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 250

High Rigidity type

B Counterbore type
X 280
D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 2
0
2
■ How to order optional specification 0
■ Order example MDC FA 2020 40 30 50 S V B N OH 200 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

507
 High Rigidity Type
F & G Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

92
34
194
184
128

212
230
90
12
Return pin

4-M12 48
20 72
Support pin

4-M6 154 Datum plane

160

◆ High regidity type

Standard type P.572
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

508
TD Technical Data P.787 STD Standard type P.572

■ How to order

■ Order example MDC FA 2023 30 30 60 S V B N OH 190 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 250

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 2
0
2
■ How to order optional specification 3
■ Order example MDC FA 2023 40 30 50 S V B N OH 200 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

509
 High Rigidity Type
F & G Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

102
34
148
204
214

232
250
100
12
Return pin

4-M12 48
20 72
Support pin

4-M6 154 Datum plane

160

◆ High regidity type

Standard type P.574
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

510
TD Technical Data P.787 STD Standard type P.574

■ How to order

■ Order example MDC FA 2025 30 30 60 S V B N OH 190 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 250

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 2
0
2
■ How to order optional specification 5
■ Order example MDC FA 2025 40 30 50 S V B N OH 200 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

511
 High Rigidity Type
F & G Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
53 90 53
M12

127
34
264
254
198

282
300
125
12
Return pin

6-M12 48
20 72
Support pin

4-M6 154 Datum plane

160

◆ High regidity type

Standard type P.576
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

512
TD Technical Data P.787 STD Standard type P.576

■ How to order

■ Order example MDC FA 2030 30 30 60 S V B N OH 190 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 250

High Rigidity type

B Counterbore type
X 280 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 30
W 40
— Types without backing plate 2
0
3
■ How to order optional specification 0
■ Order example MDC FA 2030 40 30 50 S V B N OH 200 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

513
 High Rigidity Type
F & G Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

34

92
188
184
128

210
230
90
12
Return pin

4-M12 68
20 90
Support pin

4-M8 184 Datum plane

185

◆ High regidity type

Standard type P.584
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

514
TD Technical Data P.787 STD Standard type P.584

■ How to order

■ Order example MDC FA 2323 40 40 70 S V B N OH 220 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 280

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
3
2
■ How to order optional specification 3
■ Order example MDC FA 2323 50 40 60 S V B N OH 250 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

515
 High Rigidity Type
F & G Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

102
34
208
204
148

230
250
100
12
Return pin

4-M12 68
20 90
Support pin

4-M8 184 Datum plane

185

◆ High regidity type

Standard type P.586
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

516
TD Technical Data P.787 STD Standard type P.586

■ How to order

■ Order example MDC FA 2325 40 40 70 S V B N OH 220 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 280

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
3
2
■ How to order optional specification 5
■ Order example MDC FA 2325 50 40 60 S V B N OH 250 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

517
 High Rigidity Type
F & G Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
58 110 58
FK

127
34
258
254
196

280
300
125
12
Return pin

4-M14 68
20 90
Support pin

4-M8 184 Datum plane

185

◆ High regidity type

Standard type P.590
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

518
TD Technical Data P.787 STD Standard type P.590

■ How to order

■ Order example MDC FA 2330 40 40 70 S V B N OH 220 Option

FA FC
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 280

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
3
3
■ How to order optional specification 0
■ Order example MDC FA 2330 50 40 60 S V B N OH 250 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

Material Changes the material of Plate R, A or B

change ※ Details ☞ P.674

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

519
 High Rigidity Type
F & G Series 2335
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350
TW
230
58 110 58
FK

152
34
308
304
246

330
350
12
Return pin 150

6-M14 68
20 90
Support pin

4-M8 184 Datum plane

185

◆ High regidity type

Standard type P.592
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 20 30

A 20 30

Plate R
Plate R
B
U

13

13
C
C

15

15
25

25

520
TD Technical Data P.787 STD Standard type P.592

■ How to order

■ Order example MDC FA 2335 40 40 70 S V B N OH 220 Option

FA FC
Type サポートピンの長さ
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 280

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
3
3
■ How to order optional specification 5
■ Order example MDC FA 2335 50 40 60 S V B N OH 250 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
#EH Removes the hole for ejector rod processing & Mold Parts Edition”for details.

GAtype GCtype
B A 30

A 30
B
U

13

13
C
C

15

15
25

25

521
 High Rigidity Type
F & G Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

34

97
200
194
130

230
250
95
15
Return pin

4-M14 80
25 100
Support pin

4-M8 194 Datum plane

200

◆ High regidity type

Standard type P.596
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

522
TD Technical Data P.787 STD Standard type P.596

■ How to order

■ Order example MDC FA 2525 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 300

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
5
■ How to order optional specification
2
5
■ Order example MDC FA 2525 50 40 70 S V B N OH 250 / R20 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
Material Changes the material of Plate R, A or B processing & Mold Parts Edition”for details.
change ※ Details ☞ P.674

※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

523
 High Rigidity Type
F & G Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
63 120 63
FK

122
34
250
244
180

280
300
120
15
Return pin

4-M14 80
25 100
Support pin

4-M8 194 Datum plane

200

◆ High regidity type

Standard type P.600
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

524
TD Technical Data P.787 STD Standard type P.600

■ How to order

■ Order example MDC FA 2530 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 300

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
5
■ How to order optional specification
3
0
■ Order example MDC FA 2530 50 40 70 S V B N OH 250 / R20 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
Material Changes the material of Plate R, A or B processing & Mold Parts Edition”for details.
change ※ Details ☞ P.674

※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

525
 High Rigidity Type
F & G Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
63 120 63
M16

147
34
300
294
230

330
350
145
15
Return pin

6-M14 80
25 100
Support pin

4-M8 194 Datum plane

200

◆ High regidity type

Standard type P.602
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

526
TD Technical Data P.787 STD Standard type P.602

■ How to order

■ Order example MDC FA 2535 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 300

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
5
■ How to order optional specification
3
5
■ Order example MDC FA 2535 50 40 70 S V B N OH 250 / R20 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

527
 High Rigidity Type
F & G Series 2540
Clamping plate spec. TW
Clamping type 300

TW Bolt-fastening type 350

250
63 120 63
M16

172
34
350
344
280

380
400
15
Return pin
170

6-M14 80
25 100
Support pin

4-M8 194 Datum plane

200

◆ High regidity type

Standard type P.604
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

528
TD Technical Data P.787 STD Standard type P.604

■ How to order

■ Order example MDC FA 2540 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 300

High Rigidity type

B Counterbore type
X 350 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 35
W 50
— Types without backing plate 2
5
■ How to order optional specification
4
0
■ Order example MDC FA 2540 50 40 70 S V B N OH 250 / R20 / #FK / #EH
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

529
 High Rigidity Type
F & G Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

122
250
244
180

280
300
φ15

120
Return pin

4-M14 90
φ25 110
Support pin

4-M8 214 Datum plane

215

◆ High regidity type

Standard type P.610
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

530
TD Technical Data P.787 STD Standard type P.610

■ How to order

■ Order example MDC FA 2730 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 320

High Rigidity type

B Counterbore type
X 400 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 40
W 50
— Types without backing plate 2
7
■ How to order optional specification
3
0
■ Order example MDC FA 2730 50 40 70 S V B N OH 250 / R20 / #FK
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

531
 High Rigidity Type
F & G Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
68 130 68
M16

147
300
294
230

330
350
145
φ15
Return pin

6-M14 90
φ25 110
Support pin

4-M8 214 Datum plane

215

◆ High regidity type

Standard type P.612
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 25 35

A 25 35

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

532
TD Technical Data P.787 STD Standard type P.612

■ How to order

■ Order example MDC FA 2735 40 40 70 S V B N OH 230 Option

FA FC
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 320

High Rigidity type

B Counterbore type
X 400 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 40
W 50
— Types without backing plate 2
7
■ How to order optional specification
3
5
■ Order example MDC FA 2735 50 40 70 S V B N OH 250 / R20 / #FK
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 35

A 35
B
U

15

15
C
C

20

20
25

25

533
 High Rigidity Type
F & G Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

117
250
234
164

280
300
φ15

115
Return pin

4-M14 106
φ30 120
Support pin Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.624
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 30 45

A 30 45

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

534
TD Technical Data P.787 STD Standard type P.624

■ How to order

■ Order example MDC FA 3030 50 50 80 S V B N OH 280 Option

FA FC
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
30 35 40 50 60 70 310 320 330 340 350 360
A DIMM 80 90 100 110 120 130

30 35 40 50 60 70
B DIMM 80 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 350

High Rigidity type

B Counterbore type
X 400 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 45
W 60
— Types without backing plate 3
0
■ How to order optional specification
3
0
■ Order example MDC FA 3030 50 60 70 S V B N OH 290 / R25 / #FK
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 45

A 45
B
U

15

15
C
C

20

20
25

25

535
 High Rigidity Type
F & G Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M16

142
300
284
214

330
350
φ15

140
Return pin

6-M14 106
φ30 120
Support pin
Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.628
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 30 45

A 30 45

Plate R
Plate R
B
U

15

15
C

C
20

20
25

25

536
TD Technical Data P.787 STD Standard type P.628

■ How to order

■ Order example MDC FA 3035 50 50 80 S V B N OH 280 Option

FA FC
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 350

High Rigidity type

B Counterbore type
X 400 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 45
W 60
— Types without backing plate 3
0
■ How to order optional specification
3
5
■ Order example MDC FA 3035 50 60 70 S V B N OH 290 / R25 / #FK
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 45

A 45
B
U

15

15
C
C

20

20
25

25

537
 High Rigidity Type
F & G Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
78 140 78
M20

167
350
334
264

380
400
165
φ15
Return pin

6-M14 106
φ30 120
Support pin
Datum plane
4-M8 234
240

◆ High regidity type

Standard type P.630
Mold base specification which features wider spacer block than the standard type
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype
B A 30 45

A 30 45

Plate R
Plate R
B
U

15

15
C

C
20

20
30

30

538
TD Technical Data P.787 STD Standard type P.630

■ How to order

■ Order example MDC FA 3040 50 50 80 S V B N OH 280 Option

FA FC
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）

Width of clamping
Specification of ejector
S 350

High Rigidity type

B Counterbore type
X 400 D Spacer type
※ The order method (code) of this part is
U DIMM
different from that of standard type.
V 45
W 60
— Types without backing plate 3
0
■ How to order optional specification
4
0
■ Order example MDC FA 3040 50 60 70 S V B N OH 290 / R25 / #FK
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

GAtype GCtype
B A 45

A 45
B
U

15

15
C
C

20

20
30

30

539
 F&G Series 1113

175
110
24 60 24

51
24

108
130
102
88
66

49
10
Return pin

4-M8 30
12 46
Support pin

4-M5 82 Datum plane

90

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13
13

C
C

13
13
15

15
15

540 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 1113 25 25 50 X V M N OH 150 Option

FA FC FE FF
Type Length of support pin
GA GC
60 70 80 90 100 110
Nominal Dimension 120 150

20 25 30 35 40 50
A DIMM 60

20 25 30 35 40 50
B DIMM 60

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 40 50
※ When selecting FE or FF without Plate C, specify 00.

U DIMM Specification of ejector

V 25 M Counterbore type 1
W 30 L Spacer type 1
— Types without backing plate — When selecting FE or FF type 1
3

■ How to order optional specification

■ Order example MDC FE 1113 30 25 40 X V - N OH 150 / S20

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 10 A 10 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

13
13
15
15

15

541
 F&G Series 1313

175
130
24 80 24

51
24
102

108
130
88
66

49
10
Return pin

4-M8 48
12 66
Support pin

102 Datum plane

4-M5
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13
13

C
C

13
13
15

15
15

542 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 1313 25 25 50 X V M N OH 150 Option

FA FC FE FF
Type Length of support pin
GA GC
60 70 80 90 100 110
Nominal Dimension 120 150

20 25 30 35 40 50
A DIMM 60

20 25 30 35 40 50
B DIMM 60

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 40 50
※ When selecting FE or FF without Plate C, specify 00.

U DIMM Specification of ejector

V 25 M Counterbore type 1
W 30 L Spacer type 3
— Types without backing plate — When selecting FE or FF type 1
3

■ How to order optional specification

■ Order example MDC FE 1313 30 25 40 X V - N OH 150 / S20

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 10 A 10 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

13
13
15
15

15

543
 F&G Series 1315

175
130
24 80 24

61
24
122
108

128
150
86

59
10
Return pin

4-M8 48
12 66
Support pin

102 Datum plane

4-M5
110

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 10 A 10 25
B A 10 25

Plate R
Plate R
A 10 25

Plate R
Plate S
B
U

U
13
13

C
C

13
13
15

15
15

544 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 1315 25 25 50 X V M N OH 150 Option

FA FC FE FF
Type Length of support pin
GA GC
60 70 80 90 100 110
Nominal Dimension 120 150

20 25 30 35 40 50
A DIMM 60

20 25 30 35 40 50
B DIMM 60

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 40 50
※ When selecting FE or FF without Plate C, specify 00.

U DIMM Specification of ejector

V 25 M Counterbore type 1
W 30 L Spacer type 3
— Types without backing plate — When selecting FE or FF type 1
5

■ How to order optional specification

■ Order example MDC FE 1315 30 25 40 X V - N OH 150 / S20

Code Description Code Description
#EH Removes the hole for ejector rod
Plate S Thickness
Changes the Plate S thickness 10 to
20 or 30

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 10 A 10 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

13
13
15
15

15

545
 F&G Series 1515
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

34

57
114

132
150
66

12

55
Return pin

4-M10 48
16 72
Support pin
Datum plane
4-M6 114
120

High Rigidity type P.486

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

546 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.486

■ How to order

■ Order example MDC FA 1515 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 1
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1515 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

547
 F&G Series 1518
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

34

72
144

162
180
96

70
12
Return pin

4-M10 48
16 72
Support pin

4-M6 114 Datum plane

120

High Rigidity type P.488

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

548 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.488

■ How to order

■ Order example MDC FA 1518 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 1
V 30 8
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1518 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

549
 F&G Series 1520
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

82
34
164
116

182
200
80
12
Return pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120

High Rigidity type P.490

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

550 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.490

■ How to order

■ Order example MDC FA 1520 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 2
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1520 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

551
 F&G Series 1523
Clamping plate spec. TW
Clamping type 200
Bolt-fastening type 230

TW
150
28 90 28
M12

97
34

212
230
194
146

12 95
Return pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120

High Rigidity type P.492

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

552 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.492

■ How to order

■ Order example MDC FA 1523 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 2
V 30 3
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1523 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

553
 F&G Series 1525
Clamping plate spec. TW
Clamping type 200
TW Bolt-fastening type 230

150
28 90 28
M12

107
34
214
166

232
250
105
12
Return pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120

High Rigidity type P.494

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

554 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.494

■ How to order

■ Order example MDC FA 1525 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 2
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1525 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

555
 F&G Series 1530
TW Clamping plate spec. TW
Clamping type 200
150 Bolt-fastening type 230
28 90 28
M12

132
34

282
300
264
216

130

12
Return pin

4-M10 48
16 72
Support pin Datum plane
4-M6 114
120
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 25
B A 15 25

Plate R
Plate R
A 15 25

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20
20

20

556 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 1530 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
80 90 100 110 120 130
Nominal Dimension 140 150 160 170 180 190
200 210 220
20 25 30 35 40 50
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
200
230
M Counterbore type 1
L Spacer type 5
U DIMM — When selecting FE or FF type 3
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1530 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 25

B A 25

Plate R
A 25

Plate S
B
U

13
13
C

15
15
20

20

20

557
 F&G Series 1818
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

67
34
138
134

160
180
78

65
12
Return pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Rigidity type P.496

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

558 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.496

■ How to order

■ Order example MDC FA 1818 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 1
V 30 8
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1818 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

559
 F&G Series 1820
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

77
34
158
154

180
200
98

75
12
Return pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Rigidity type P.498

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

560 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.498

■ How to order

■ Order example MDC FA 1820 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 2
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1820 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

561
 F&G Series 1823
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

92
34
188
184
128

210
230
90
12
Return pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Rigidity type P.500

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

562 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.500

■ How to order

■ Order example MDC FA 1823 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 2
V 30 3
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1823 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

563
 F&G Series 1825
Clamping plate spec. TW
Clamping type 230
Bolt-fastening type 280

TW
180
33 110 33
M12

102
34

230
250
208
204
148

100
12
Return pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Rigidity type P.502

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

564 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.502

■ How to order

■ Order example MDC FA 1825 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 2
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1825 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

565
 F&G Series 1830
Clamping plate spec. TW
Clamping type 230
TW Bolt-fastening type 280

180
33 110 33
M12

127
34

280
300
258
254
198

125
12
Return pin

4-M12 68
20 90
Support pin Datum plane
4-M8 140
145

High Rigidity type P.504

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

566 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.504

■ How to order

■ Order example MDC FA 1830 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 3
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1830 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

567
 F&G Series 1835
TW Clamping plate spec. TW
Clamping type 230
180 Bolt-fastening type 280
33 110 33
M12

152
34

330
350
308
304
248

150

12
Return pin

6-M12 68
20 90
Support pin Datum plane
4-M8 140
145
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 15 A 15 30
B A 15 30

Plate R
Plate R
A 15 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
20

20
20

568 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 1835 30 30 60 S V M N OH 180 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80

20 25 30 35 40 50
B DIMM 60 70 80

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping
Specification of ejector
S
X
230
280
M Counterbore type 1
L Spacer type 8
U DIMM — When selecting FE or FF type 3
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 1835 40 30 50 S V - N OH 190 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 15 A 15 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
20
20
20

569
 F&G Series 2020
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

77
34
154
150

180
200
98

12

75
Return pin

4-M12 84
20 100
Support pin Datum plane
4-M8 154
160

High Rigidity type P.506

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
13

13

C
C

C
15

15
25

25

25

570 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.506

■ How to order

■ Order example MDC FA 2020 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
2
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2020 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

13

13
C

C
15

15
25

25
25

571
 F&G Series 2023
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

92
34
184
180
128

210
230
15

90
Return pin

4-M12 80
20 100
Support pin
Datum plane
4-M8 154
160

High Rigidity type P.508

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

572 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.508

■ How to order

■ Order example MDC FA 2023 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
2
V 30 3
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2023 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

573
 F&G Series 2025
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

102
34

230
250
204
200
148

100
15
Return pin

4-M12 80
20 100
Support pin Datum plane
4-M8 154
160

High Rigidity type P.510

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

574 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.510

■ How to order

■ Order example MDC FA 2025 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
2
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2025 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

575
 F&G Series 2030
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

127
34
254
250
198

280
300
15 125
Return pin

6-M12 80
20 100
Support pin Datum plane
4-M8 154
160

High Rigidity type P.512

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

576 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.512

■ How to order

■ Order example MDC FA 2030 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
3
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2030 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

577
 F&G Series 2035
Clamping plate spec. TW
Clamping type 250
Bolt-fastening type 280

TW
200
38 120 38
M12

152
34

330
350
304
300
248

150
15
Return pin

6-M12 80
20 100
Support pin
Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

578 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2035 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
3
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2035 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

579
 F&G Series 2040
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 250
50 or more Ｍ16 TW Bolt-fastening type 280

200
38 120 38
FK

177
34
354
350
298

380
400
175

15
Return pin

6-M12 80
20 100
Support pin
Datum plane
4-M8 154
160

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

580 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2040 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
4
V 30 0
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2040 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

581
 F&G Series 2045
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12
TW Clamping type 250
50 or more Ｍ16 200 Bolt-fastening type 280

38 120 38
FK

202
34

430
450
404
400
348

200

15
Return pin

6-M12 80
20 100
Support pin
Datum plane
4-M8 154
160
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

582 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2045 30 30 60 S V M N OH 190 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
20 25 30 35 40 50 270 280
A DIMM 60 70 80 90 100

20 25 30 35 40 50
B DIMM 60 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 50 60 70 80 90
※ If A and B dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 250 M Counterbore type 2
X 280 L Spacer type 0
U DIMM — When selecting FE or FF type
4
V 30 5
W 40
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2045 40 30 50 S V - N OH 200 / S30 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

583
 F&G Series 2323
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

92
34
184
180
128

210
230
15

90
Return pin

4-M12 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.514

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

584 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.514

■ How to order

■ Order example MDC FA 2323 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
2
V 35 3
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2323 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

585
 F&G Series 2325
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

102
34

230
250
204
200
148

100
15
Return pin

4-M12 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.516

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

586 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.516

■ How to order

■ Order example MDC FA 2325 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
2
V 35 5
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2325 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

587
 F&G Series 2327
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

112
34

250
270
224
220
166

110
15
Return pin

4-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

588 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2327 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
2
V 35 7
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2327 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

589
 F&G Series 2330
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

127
34
254
250
196

280
300
125
15
Return pin

4-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.518

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

590 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.518

■ How to order

■ Order example MDC FA 2330 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
3
V 35 0
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2330 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
Material Changes the material of Plate R, A, S or B See the separate volume“Additional Mold Base
change ※ Details ☞ P.674 processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

591
 F&G Series 2335
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 280
50 or more Ｍ16 Bolt-fastening type 350

TW
230
43 140 43
FK

152
34
304
300
246

330
350
15 150
Return pin

6-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

High Rigidity type P.520

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

592 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.520

■ How to order

■ Order example MDC FA 2335 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
3
V 35 5
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2335 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

593
 F&G Series 2340
Clamping plate spec. TW
Clamping type 280
TW Bolt-fastening type 350

230
43 140 43
M16

177
34

380
400
354
350
296

175
15
Return pin

6-M14 106
20 120
Support pin
Datum plane
4-M8 184
185

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 20 A 20 30
B A 20 30

Plate R
Plate R
A 20 30

Plate R
Plate S
B
U

U
15

15

C
C

20
20

25

25
25

594 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2340 40 40 70 S V M N OH 220 Option

FA FC FE FF
Type Length of support pin
GA GC
90 100 110 120 130 140
Nominal Dimension 150 160 170 180 190 200
210 220 230 240 250 260
25 30 35 40 50 60 270 280
A DIMM 70 80 90 100

25 30 35 40 50 60
B DIMM 70 80 90 100

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 280 M Counterbore type 2
X 350 L Spacer type 3
U DIMM — When selecting FE or FF type
4
V 35 0
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2340 50 40 60 S V - N OH 250 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
#EH Removes the hole for ejector rod
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

FFtype GAtype GCtype

B 20 A 20 30

B A 30

Plate R
A 30

Plate S
B
U

15
15
C

20
20
25

25

25

595
 F&G Series 2525
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

97
34

230
250
200
194
130

95
15
Return pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.522

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

596 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.522

■ How to order

■ Order example MDC FA 2525 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
2
W 50 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2525 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.674
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

597
 F&G Series 2527
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

107
34

250
270
220
214
150

105
15
Return pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

598 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2527 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
2
W 50
7
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2527 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.674
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

599
 F&G Series 2530
B DIMM FK Clamping plate spec. TW
40 or less Ｍ12 Clamping type 300
50 or more Ｍ16 Bolt-fastening type 350

TW
250
48 150 48
FK

122
34
250
244
180

280
300
120
15
Return pin

4-M14 110
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.524

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

600 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.524

■ How to order

■ Order example MDC FA 2530 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
3
W 50 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2530 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Material Changes the material of Plate R, A, S or B
change ※ Details ☞ P.674
Additional Specifications other than the above are also available.
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

601
 F&G Series 2535
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
48 150 48
M16

147
34

330
350
298
294
230

20 145
Return pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.526

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

602 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.526

■ How to order

■ Order example MDC FA 2535 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
3
W 50 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2535 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

603
 F&G Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350
TW
250
48 150 48
M16

172
34

380
400
348
344
280

170
20
Return pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

High Rigidity type P.528

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

604 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787 HR High Rigidity type P.528

■ How to order

■ Order example MDC FA 2540 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
4
W 50 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2540 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

605
 F&G Series 2545
Clamping plate spec. TW
Clamping type 300
TW Bolt-fastening type 350

250
48 150 48
M16

197
34
398
394
330

430
450
195

20
Return pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

606 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2545 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
4
W 50 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2545 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

607
 F&G Series 2550
Clamping plate spec. TW
TW Clamping type 300
250 Bolt-fastening type 350

48 150 48
M16

222
34

480
500
448
444
380

220

20
Return pin

6-M14 102
25 130
Support pin
Datum plane
4-M8 194
200

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15

15

C
C

C
20

20
25
25

25

608 ※※ FEForand FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
FE & FF type, ejector rod hole will not be machined.
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2550 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
25 30 35 40 50 60 280 290 300 320
A DIMM 70 80 90 100 110 120

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 60 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 300 M Counterbore type 2
X 350 L Spacer type 5
V 35
U DIMM — When selecting FE or FF type
5
W 50 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2550 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25

25
25

609
 F&G Series 2730
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

122
276
300
244
240
180

120
20
Return pin

4-M14 114
25 136
Support pin Datum plane
4-M10 214
215

High Rigidity type P.530

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15
15

C
C

20
20
25

25

25

610 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787 HR High Rigidity type P.530

■ How to order

■ Order example MDC FA 2730 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 320 M Counterbore type 2
X 400 L Spacer type 7
V
U DIMM — When selecting FE or FF type 3
0
40
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2730 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25
25

25

611
 F&G Series 2735
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

147
326
350
294
290
230

145
20
Return pin

6-M14 114
25 136
Support pin Datum plane
4-M10 214
215

High Rigidity type P.532

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15
15

C
C

20
20
25

25

25

612 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787 HR High Rigidity type P.532

■ How to order

■ Order example MDC FA 2735 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 320 M Counterbore type 2
X 400 L Spacer type 7
V 40
U DIMM — When selecting FE or FF type 3
W 50
5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2735 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25
25

25

613
 F&G Series 2740
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

172
344
340
280

376
400
20 170
Return pin

6-M14 114
25 136
Support pin Datum plane
4-M10 214
215

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15
15

C
C

20
20
25

25

25

614 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2740 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 320 M Counterbore type 2
X 400 L Spacer type 7
V
U DIMM — When selecting FE or FF type 4
0
40
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2740 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25
25

25

615
 F&G Series 2750
B DIMM FK Clamping plate spec. TW
70 or less Ｍ16
TW Clamping type 320
80 or more Ｍ20 270 Bolt-fastening type 400

53 160 53
FK

222
476
500
444
440
380

220

20
Return pin

6-M14 114
25 136
Support pin Datum plane
4-M10 214
215
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
15
15

C
C

20
20
25

25

25

616 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2750 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 320 M Counterbore type 2
X 400 L Spacer type 7
V
U DIMM — When selecting FE or FF type 5
0
40
W 50
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2750 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

15
15
C

20
20
25
25

25

617
 F&G Series 2930
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

122
276
300
244
240
180

120
20
Return pin

4-M14 134
25 156
Support pin Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
20

20

C
C

25
25
25

25

25

618 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2930 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 2
X 400 L Spacer type 9
V 40
U DIMM — When selecting FE or FF type
3
W 50 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2930 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

20

20
C

C
25

25
25
25

25

619
 F&G Series 2935
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

147
326
350
294
290
230

145
20
Return pin

6-M14 134
25 156
Support pin Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
20

20

C
C

25
25
25

25

25

620 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2935 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 2
X 400 L Spacer type 9
V 40
U DIMM — When selecting FE or FF type
3
W 50 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2935 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

20

20
C

C
25

25
25
25

25

621
 F&G Series 2940
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
290
53 180 53
M16

172
376
400
344
340
280

20
Return pin 170

6-M14 134
25 156
Support pin Datum plane
4-M10 234
235

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 25 A 25 35
B A 25 35

Plate R
Plate R
A 25 35

Plate R
Plate S
B
U

U
20

20

C
C

25
25
25

25

25

622 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 2940 40 40 70 S V M N OH 230 Option

FA FC FE FF
Type Length of support pin
GA GC
100 110 120 130 140 150
Nominal Dimension 160 170 180 190 200 210
220 230 240 250 260 270
30 35 40 50 60 70 280 290 300 320
A DIMM 80 90 100 110 120

30 35 40 50 60 70
B DIMM 80 90 100 110 120

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 2
X 400 L Spacer type 9
V 40
U DIMM — When selecting FE or FF type
4
W 50 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 2940 50 40 70 S V - N OH 250 / R20 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 25 A 25 35

B A 35

Plate R
A 35

Plate S
B
U

20

20
C

C
25

25
25
25

25

623
 F&G Series 3030
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

117
240
234
164

276
300
115
20
Return pin

4-M14 134
30 156
Support pin Datum plane
4-M10 234
240

High Rigidity type P.534

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20

20

C
C

C
25

25
25

25
25

624 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787 HR High Rigidity type P.534

■ How to order

■ Order example MDC FA 3030 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
30 35 40 50 60 70 310 320 330 340 350 360
A DIMM 80 90 100 110 120 130

30 35 40 50 60 70
B DIMM 80 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
3
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3030 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
25

25

25

625
 F&G Series 3032
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

127
260
254
184

296
320
125
20
Return pin

4-M14 134
30 156
Support pin Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20

20

C
C

C
25

25
25

25
25

626 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3032 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
3
W 60 2
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3032 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
25

25

25

627
 F&G Series 3035
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M16

142
290
284
214

326
350
140
20
Return pin

6-M14 134
30 156
Support pin Datum plane
4-M10 234
240

High Rigidity type P.536

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20

20

C
C

C
25

25
25

25
25

628 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787 HR High Rigidity type P.536

■ How to order

■ Order example MDC FA 3035 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
3
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3035 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
25

25

25

629
 F&G Series 3040
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400

TW
300
58 180 58
M20

167
340
334
264

376
400
20 165
Return pin

6-M14 134
30 156
Support pin Datum plane
4-M10 234
240

High Rigidity type P.538

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

630 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787 HR High Rigidity type P.538

■ How to order

■ Order example MDC FA 3040 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
4
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3040 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

631
 F&G Series 3045
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400
TW
300
58 180 58
M20

192
390
384
312

426
450
190
25
Return pin

6-M16 128
30 156
Support pin Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

632 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3045 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
4
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3045 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

633
 F&G Series 3050
Clamping plate spec. TW
Clamping type 350

TW Bolt-fastening type 400

300
58 180 58
M20

217
440
434
362

476
500
215

25
Return pin

6-M16 128
30 156
Support pin Datum plane
4-M10 234
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

634 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3050 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 350 M Counterbore type 3
X 400 L Spacer type 0
V 45
U DIMM — When selecting FE or FF type
5
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3050 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

635
 F&G Series 3335
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

142
290
284
214

326
350
140
25
Return pin

6-M14 154
30 186
Support pin Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

636 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3335 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 3
V 45
U DIMM — When selecting FE or FF type
3
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3335 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

637
 F&G Series 3340
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

167
340
334
264

376
400
165
25
Return pin

6-M14 154
30 186
Support pin Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

638 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3340 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 3
V 45
U DIMM — When selecting FE or FF type
4
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3340 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

639
 F&G Series 3345
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
330
58 210 58
M20

192
390
384
312

426
450
25 190
Return pin

6-M16 154
30 186
Support pin Datum plane
4-M10 264
270

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 30 A 30 45
B A 30 45

Plate R
Plate R
A 30 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

640 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3345 50 50 80 S V M N OH 280 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
35 40 50 60 70 80 310 320 330 340 350 360
A DIMM 90 100 110 120 130

35 40 50 60 70 80
B DIMM 90 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 3
V 45
U DIMM — When selecting FE or FF type
4
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3345 50 60 70 S V - N OH 290 / R25 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 30 A 30 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

C
25

25
30

30
30

641
 F&G Series 3535
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

142
326
350
290
284
212

140
25
Return pin

6-M16 164
30 196
Support pin Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

642 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3535 50 50 80 S V M N OH 290 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90 310 320 330 340 350 360
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 5
V 45
U DIMM — When selecting FE or FF type
3
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3535 50 60 70 S V - N OH 290 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

25
25
30

30

30

643
 F&G Series 3540
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M20

167
340
334
262

376
400
165
25
Return pin

6-M16 164
30 196
Support pin Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

644 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3540 50 50 80 S V M N OH 290 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90 310 320 330 340 350 360
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 5
V 45
U DIMM — When selecting FE or FF type
4
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3540 50 60 70 S V - N OH 290 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

25
25
30

30

30

645
 F&G Series 3545
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550

TW
350
63 220 63
M24

192
390
384
312

426
450
25
Return pin
190

6-M16 164
30 196
Support pin Datum plane
4-M10 284
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 45
B A 35 45

Plate R
Plate R
A 35 45

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

646 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3545 50 50 80 S V M N OH 290 Option

FA FC FE FF
Type Length of support pin
GA GC
130 140 150 160 170 180
Nominal Dimension 190 200 210 220 230 240
250 260 270 280 290 300
40 50 60 70 80 90 310 320 330 340 350 360
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 5
V 45
U DIMM — When selecting FE or FF type
4
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3545 50 60 70 S V - N OH 290 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 45

B A 45

Plate R
A 45

Plate S
B
U

20

20
C

25
25
30

30

30

647
 F&G Series 3550
Clamping plate spec. TW
Clamping type 400
TW Bolt-fastening type 550

350
63 220 63
M24

212
440
424
344

476
500
25 210
Return pin

6-M16 152
35 196
Support pin Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

648 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3550 50 50 80 S V M N OH 290 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 5
V 45
U DIMM — When selecting FE or FF type
5
W 60 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3550 50 60 70 S V - N OH 290 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
B
U

20
20
C

25
25
30

30
30

649
 F&G Series 3555
Clamping plate spec. TW
TW Clamping type 400
Bolt-fastening type 550
350
63 220 63
M24

237
490
474
394

526
550
235
25
Return pin

6-M16 152
35 196
Support pin Datum plane
4-M10 274
285

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

U
20
20

C
C

25
25

30
30

30

650 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 3555 50 50 80 S V M N OH 290 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 70 80 90 100 110
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 400 M Counterbore type 3
X 550 L Spacer type 5
V 45
U DIMM — When selecting FE or FF type
5
W 60 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 3555 50 60 70 S V - N OH 290 / R30 / S40 / #FK

Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
B
U

20
20
C

25
25
30

30
30

651
 F&G Series 4040
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

162
374
400
340
324
244

160
25
Return pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

U
25
25

C
C

30
30

30
30

30

652 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4040 70 70 10 S V M N OH 350 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 450 M Counterbore type 4
X 550 L Spacer type 0
V 50
U DIMM — When selecting FE or FF type
4
W 70 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4040 80 60 10 S V - N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#EB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
Removes the threaded holes for eye bolts for Plate 40 , 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
B
U

25
25
C

30
30
30

30
30

653
 F&G Series 4045
Clamping plate spec. TW
Clamping type 450
Bolt-fastening type 550

TW
400
68 260 68
M24

187
390
374
294

424
450
185
25
Return pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
B
U

U
25
25

C
C

30
30
35

35
35

654 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4045 70 70 10 S V M N OH 350 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 450 M Counterbore type 4
X 550 L Spacer type 0
V 50
U DIMM — When selecting FE or FF type
4
W 70 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4045 80 60 10 S V - N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
Removes the threaded holes for eye bolts for Plate 40 , 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
B
U

25

25
C

C
30

30
35

35

35

655
 F&G Series 4050
HT DIMM FK Clamping plate spec. TW
80∼365 Ｍ24 Clamping type 450
370∼425 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

212
440
424
344

474
500
210
25
Return pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
HT

HT
HT
B
U

U
25

25

C
C

C
30

30
35

35
35

656 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4050 70 70 10 S V M N OH 350 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 450 M Counterbore type 4
X 550 L Spacer type 0
V 50
U DIMM — When selecting FE or FF type
5
W 70 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4050 80 60 10 S V - N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
Removes the threaded holes for eye bolts for Plate 40 , 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
HT

HT
HT

B
U

25
25
C

30
30
35

35

35

657
 F&G Series 4055
HT DIMM FK Clamping plate spec. TW
80∼310 Ｍ24 Clamping type 450
315∼425 Ｍ30 Bolt-fastening type 550

TW
400
68 260 68
FK

237
490
474
394

524
550
235
25
Return pin

6-M16 198
35 234
Support pin Datum plane
4-M12 324
330

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 35 A 35 50
B A 35 50

Plate R
Plate R
A 35 50

Plate R
Plate S
HT

HT
HT
B
U

U
25

25

C
C

C
30

30
35

35
35

658 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4055 70 70 10 S V M N OH 350 Option

FA FC FE FF
Type Length of support pin
GA GC
160 170 180 190 200 210
Nominal Dimension 220 230 240 250 260 270
280 290 300 310 320 330
40 50 60 70 80 90 340 350 360 380 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 450 M Counterbore type 4
X 550 L Spacer type 0
V 50
U DIMM — When selecting FE or FF type
5
W 70 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4055 80 60 10 S V - N OH 360 / R30 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
Removes the threaded holes for eye bolts for Plate 40 , 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 35 A 35 50

B A 50

Plate R
A 50

Plate S
HT

HT
HT

B
U

25
25
C

30
30
35

35

35

659
 F&G Series 4545
HT DIMM FK Clamping plate spec. TW
80∼360 Ｍ24 Clamping type 500
365∼440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

182
384
364
276

424
450
180
30
Return pin

6-M16 226
40 264
Support pin Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

660 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4545 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

J 500 M Counterbore type 4
S 550 L Spacer type 5
V 60
U DIMM — When selecting FE or FF type
4
W 80 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4545 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

661
 F&G Series 4550
HT DIMM FK Clamping plate spec. TW
80∼300 Ｍ24 Clamping type 500
305∼440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

207
434
414
326

474
500
205
30
Return pin

6-M16 226
40 264
Support pin Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

662 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4550 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

J 500 M Counterbore type 4
S 550 L Spacer type 5
V 60
U DIMM — When selecting FE or FF type
5
W 80 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4550 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

663
 F&G Series 4555
HT DIMM FK Clamping plate spec. TW
80∼250 Ｍ24 Clamping type 500
255∼440 Ｍ30 Bolt-fastening type 550

TW
450
78 290 78
FK

232
484
464
376

524
550
230
30
Return pin

6-M16 226
40 264
Support pin Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

664 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4555 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

J 500 M Counterbore type 4
S 550 L Spacer type 5
V 60
U DIMM — When selecting FE or FF type
5
W 80 5
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4555 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

665
 F&G Series 4560
HT DIMM FK Clamping plate spec. TW
80∼210 Ｍ24 Clamping type 500
215∼440 Ｍ30 Bolt-fastening type 550
TW
450
78 290 78
FK

257
534
514
426

574
600
30
Return pin 255

6-M16 226
40 264
Support pin Datum plane
4-M12 364
370

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

666 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 4560 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

J 500 M Counterbore type 4
S 550 L Spacer type 5
V 60
U DIMM — When selecting FE or FF type
6
W 80 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 4560 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

667
 F&G Series 5050
HT DIMM FK Clamping plate spec. TW
80∼220 Ｍ24 Clamping type 600
225∼440 Ｍ30 Bolt-fastening type 700

TW
500
88 320 88
FK

207
474
500
434
414
326

205
30
Return pin

6-M16 256
40 294
Support pin Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

668 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 5050 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 600 M Counterbore type 5
X 700 L Spacer type 0
V 60
U DIMM — When selecting FE or FF type
5
W 80 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 5050 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

669
 F&G Series 5060
HT DIMM FK Clamping plate spec. TW
80∼380 Ｍ30 Clamping type 600
385∼440 Ｍ36 Bolt-fastening type 700

TW
500
88 320 88
FK

257
534
514
426

574
600
255
30
Return pin

6-M16 256
40 294
Support pin Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

670 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 5060 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 600 M Counterbore type 5
X 700 L Spacer type 0
V 60
U DIMM — When selecting FE or FF type
6
W 80 0
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 5060 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

671
 F&G Series 5070
HT DIMM FK Clamping plate spec. TW
80∼280 Ｍ30 Clamping type 600
285∼440 Ｍ36 Bolt-fastening type 700
● The dimension of Plate A or Plate TW
B is 40, M30 is applied for FK.
500
88 320 88
FK

307
674
700
634
614
526

305
30
Return pin

6-M16 256
40 294
Support pin Datum plane
4-M12 410
414

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

FAtype FCtype FEtype

B 40 A 40 60
B A 40 60

Plate R
A 40 60

Plate R
Plate R
Plate S
HT

HT
HT
B
U

U
25
25

C
C

30
30
35

35

35

672 ※ FE and FF specifications without Plate C are also available (When ordering them, please specify 00 for C dimension).
TD Technical Data P.787

■ How to order

■ Order example MDC FA 5070 70 70 10 S V M N OH 380 Option

FA FC FE FF
Type Length of support pin
GA GC
200 210 220 230 240 250
Nominal Dimension 260 270 280 290 300 310
320 330 340 350 360 380
40 50 60 70 80 90 400
A DIMM 100 110 120 130

40 50 60 70 80 90
B DIMM 100 110 120 130

F & G series
3-Plate Type
This may be changed to J or P by
Futaba if there is any addition or
change to the specification.
C DIMM 100 110 120 130
※ If A, B and C dimension are 3 digits, specify the dimension with the first two-digit numbers.
e.g.:（100→ 10 ）
※ When selecting FE or FF without Plate C, specify 00.

Width of clamping Specification of ejector

S 600 M Counterbore type 5
X 700 L Spacer type 0
V
U DIMM — When selecting FE or FF type
7
0
60
W 80
— Types without backing plate

■ How to order optional specification

■ Order example MDC FE 5070 80 60 10 S V - N OH 380 / R35 / S50 / #FK

Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R35 Changes the Plate R thickness 40 to 35 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 40 to
Removes the threaded holes for eye bolts for Plate 50 or 60
#FK A and B Specifications other than the above are also available.
Additional
See the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

FFtype GAtype GCtype

B 40 A 40 60

B A 60

Plate R
A 60

Plate S
HT

HT
HT

B
U

25

25
C

C
30

30
35

35
35

673
 F&G Series Material Change Option

FAtype FCtype FEtype

Plate R
Plate R
Plate A
Plate A Plate R
Plate S
Plate A
Plate B Plate B
Plate B

FFtype GAtype GCtype

Plate R
Plate A Plate R
Plate S Plate A
Plate B
Plate B Plate B

■ How to order material change specification

■ Order example MDC FA 1518 40 30 50 S V M N OH 170 / F – AB

Material changing plate code

R Runner plate
A Cavity plate (fixed half)
S Stripper plate
Mold base order code
When ordering, specify the mold
B Cavity plate (moving half)
base specification with codes shown Following the − symbol, specify the
in each page. material changing plate. The plate of
which material can be changed are the
above four types, Plate R, A, S and B.

◆How to order Material designation code

In addition to the mold base order codes, please specify F HPM1
“Material designation code”and“Material changing K NAK55
plate code” . R NAK80

674
TD Technical Data P.787

Mold base
Material designation code Material name Plate A thickness Plate B thickness Plate R thickness Plate S thickness
nominal
1515
1518
1520
1523
15 15 20 30 40
1818 20 25 30 35 40 20 25 30 35 40
1820
1823
1825
F HPM1 2020
K NAK55 2023
20 30 40
R NAK80 2025 25 30 35 40 25 30 35 40
2030
20
2323

F & G series
3-Plate Type
2325
20 30 40 50
2327 25 30 35 40 50 25 30 35 40 50
2330
2525
2527 20 25 25 30 40 50
30 35 40 50 30 35 40 50
2530
※ Product of materials and sizes not listed above will also be made to order. Please consult our sales office.

Material Change Option

675
 F&G Series Material Change Option

676
 THREE-PLATE TYPE H-SERIES
3-Plate Type
H series
■Structure and Component Name ・・・・・・・・・・・・・・・・・・・・・・・ P.678

■H Series

  2540∼2750 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.680∼689

  3045∼3350 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.690∼699

  3550∼3560 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.700∼705

  4060∼4070 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.706∼709
 H Series Structure & Component Name

Hexagon socket head cap screw Threaded hole for eye bolt

Puller bolt

Support pin
Hole for ejector rod

Hexagon socket head cap screw

Guide pin & guide bushing Return pin

T Top clamping plate PBC Puller bolt

R Runner plate

A Cavity plate (fixed half) GBA Guide bushing

S Stripper plate GBB Guide bushing

GPA Guide pin
B Cavity plate (moving half)

U Backing plate PBA Puller bolt

SPN Support pin

C Spacer block RPN Return pin

E Ejector retainer plate

F Ejector base plate

L Bottom clamping plate

This diagram shows HB type as a representative example.

678
HAType HCType
Ejector pin ejection type without backing
Ejector pin ejection type
plate

T PBC
R T PBC

A GBA R
B A GBA
GPA
U B GPA
PBA
SPN SPN PBA
C RPN C RPN
E E

H series
3-Plate Type
F F
L L

Structure and Component Name

HBType HDType
Stripper plate ejection type without backing
Stripper plate ejection type
plate

T PBC
T PBC
R
A GBA R
S GBB A GBA

B GPA S GBB

U PBA B GPA

SPN SPN PBA

C RPN C RPN
E E
F F
L L

679
 H Series 2540
Clamping plate spec. TW
Clamping type 300
Bolt-fastening type 350

TW
250
48 150 48
M16

147
118
34
380
356
294
290
236

350
400
116
25

145
Support pin

25
Guide pin
15
Return pin

102
6-M14 130
20 140 Datum plane
Puller bolt
194
4-M8
200
220

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 25 A 25 35
10
B A 25 35

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

15
15

C
C

20
20

25
25

680
TD Technical Data P.787

■ How to order

■ Order example MDC HA 2540 40 40 70 S V M N IH 230:150 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120

Length of support pin

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120 100 110 120 130 140 150
160 170 180 190 200 210
220 230 240 250 260 270
C DIMM 60 70 80 90 100
280 290 300 320
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 300

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate 2

5
■ How to order optional specification 4
■ Order example MDC HB 2540 40 50 70 S V M N IH 230:150 / R20 / S40 / #FK / #EH 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 25 A 25 35
10
A 25 35

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

15

15
C

C
20

20
25

25

681
 H Series 2545
Clamping plate spec. TW
Clamping type 300
TW Bolt-fastening type 350

250
48 150 48
M16

172
143
34
430
406
344
340
286

400
450
141
170
25
Support pin

25
Guide pin
15
Return pin

102
6-M14 130
20 140 Datum plane
Puller bolt
194
4-M8
200
220

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 25 A 25 35
10
B A 25 35

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

15
15

C
C

20
20

25
25

682
TD Technical Data P.787

■ How to order

■ Order example MDC HA 2545 40 40 70 S V M N IH 230:150 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120

Length of support pin

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120 100 110 120 130 140 150
160 170 180 190 200 210
220 230 240 250 260 270
C DIMM 60 70 80 90 100
280 290 300 320
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 300

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate 2

5
■ How to order optional specification 4
■ Order example MDC HB 2545 40 50 70 S V M N IH 230:150 / R20 / S40 / #FK / #EH 5
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 25 A 25 35
10
A 25 35

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

15

15
C

C
20

20
25

25

683
 H Series 2550
Clamping plate spec. TW
TW Clamping type 300
250 Bolt-fastening type 350
48 150 48
M16

197
168
34
480
456
394
390
336

450
500
166
195
25
Support pin

25
Guide pin
15
Return pin

102
6-M14 130
20 140 Datum plane
Puller bolt
194
4-M8
200
220
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 25 A 25 35
10
B A 25 35

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

15
15

C
C

20
20

25
25

684
TD Technical Data P.787

■ How to order

■ Order example MDC HA 2550 40 40 70 S V M N IH 230:150 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260
25 30 35 40 50 60
A DIMM 70 80 90 100 110 120

Length of support pin

25 30 35 40 50 60
B DIMM 70 80 90 100 110 120 100 110 120 130 140 150
160 170 180 190 200 210
220 230 240 250 260 270
C DIMM 60 70 80 90 100
280 290 300 320
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 300

X 350 U DIMM Specification of ejector

V 35 M Counterbore type
Y 300
W 50 L Spacer type

Z 350 — Types without backing plate 2

5
■ How to order optional specification 5
■ Order example MDC HB 2550 40 50 70 S V M N IH 230:150 / R20 / S40 / #FK / #EH 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※

#EH Removes the hole for ejector rod

Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 25 A 25 35
10
A 25 35

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

15

15
C

C
20

20
25

25

685
 H Series 2740
Clamping plate spec. TW
Clamping type 320
Bolt-fastening type 400

TW
270
53 160 53
M16

147
118
376
356
294
290
236

350
400
116
25

145
Support pin

25
Guide pin
15
Return pin

104
6-M14 136
20 160 Datum plane
Puller bolt
214
4-M10
220
240

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 25 A 25 35
10
B A 25 35

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
15

15
C
C

20

20
25
25

686
TD Technical Data P.787

■ How to order

■ Order example MDC HA 2740 40 40 70 S V M N IH 230:150 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260
30 35 40 50 60 70
A DIMM 80 90 100 110 120

Length of support pin

30 35 40 50 60 70
B DIMM 80 90 100 110 120 100 110 120 130 140 150
160 170 180 190 200 210
220 230 240 250 260 270
C DIMM 70 80 90 100
280 290 300 320
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 320

X 400 U DIMM Specification of ejector

V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate 2

7
■ How to order optional specification 4
■ Order example MDC HB 2740 40 50 70 S V M N IH 230:150 / R20 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 25 A 25 35
10
A 25 35

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

15

15
C

C
20

20
25

25

687
 H Series 2750
B DIMM FK Clamping plate spec. TW
70 or less Ｍ16
TW Clamping type 320
80 or more Ｍ20 270 Bolt-fastening type 400
53 160 53
FK

197
168
476
456
394
390
336

450
500
166
195
25
Support pin

25
Guide pin
15
Return pin

104
6-M14 136
20
Puller bolt
160 Datum plane
214
4-M10
220
240
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 25 A 25 35
10
B A 25 35

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
15

15
C
C

20

20
25
25

688
TD Technical Data P.787

■ How to order

■ Order example MDC HA 2750 40 40 70 S V M N IH 230:150 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260
30 35 40 50 60 70
A DIMM 80 90 100 110 120

Length of support pin

30 35 40 50 60 70
B DIMM 80 90 100 110 120 100 110 120 130 140 150
160 170 180 190 200 210
220 230 240 250 260 270
C DIMM 70 80 90 100
280 290 300 320
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 320

X 400 U DIMM Specification of ejector

V 40 M Counterbore type
Y 320
W 50 L Spacer type

Z 400 — Types without backing plate 2

7
■ How to order optional specification 5
■ Order example MDC HB 2750 40 50 70 S V M N IH 230:150 / R20 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R20 Changes the Plate R thickness 25 to 20 ※
Changes the Plate S thickness 25 to
Plate S Thickness
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 25 A 25 35
10
A 25 35

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

15

15
C

C
20

20
25

25

689
 H Series 3045
Clamping plate spec. TW
Clamping type 350
Bolt-fastening type 400
TW
300
58 180 58
M20

173
135

400
450
426
396
346
336
270

133
30

171
Support pin

30
20 Guide pin
Return pin

110
6-M16 156
20 180 Datum plane
Puller bolt
234
4-M10
250
266

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 30 A 30 45
10
B A 30 45

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
20

20
C
C

25

25
30
30

690
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3045 50 50 80 S V M N IH 280:190 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260 280
35 40 50 60 70 80
A DIMM 90 100 110 120 130

Length of support pin

35 40 50 60 70 80
B DIMM 90 100 110 120 130 130 140 150 160 170 180
190 200 210 220 230 240
250 260 270 280 290 300
C DIMM 70 80 90 100 110
310 320 330 340 350 360
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 350

X 400 U DIMM Specification of ejector

V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate 3

0
■ How to order optional specification 4
■ Order example MDC HB 3045 50 60 70 S V M N IH 280:190 / R25 / S40 / #FK 5
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 30 A 30 45
10
A 30 45

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

691
 H Series 3050
Clamping plate spec. TW
Clamping type 350

TW Bolt-fastening type 400

300
58 180 58
M20

198
160

450
500
476
446
396
386
320

158
30

196
Support pin

30
20 Guide pin
Return pin

110
6-M16 156
20 180 Datum plane
Puller bolt
234
4-M10
250
266

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 30 A 30 45
10
B A 30 45

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
20

20
C
C

25

25
30
30

692
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3050 50 50 80 S V M N IH 280:190 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260 280
35 40 50 60 70 80
A DIMM 90 100 110 120 130

Length of support pin

35 40 50 60 70 80
B DIMM 90 100 110 120 130 130 140 150 160 170 180
190 200 210 220 230 240
250 260 270 280 290 300
C DIMM 70 80 90 100 110
310 320 330 340 350 360
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 350

X 400 U DIMM Specification of ejector

V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate 3

0
■ How to order optional specification 5
■ Order example MDC HB 3050 50 60 70 S V M N IH 280:190 / R25 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 30 A 30 45
10
A 30 45

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

693
 H Series 3055
Clamping plate spec. TW
TW Clamping type 350

300 Bolt-fastening type 400

58 180 58
M24

223
185
526
496
446
436
370

500
550
183
221
30
Support pin

30
20 Guide pin
Return pin

110
6-M16 156
20 180 Datum plane
Puller bolt
234
4-M10
250
266

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 30 A 30 45
10
B A 30 45

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
20

20
C
C

25

25
30
30

694
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3055 50 50 80 S V M N IH 280:190 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260 280
35 40 50 60 70 80
A DIMM 90 100 110 120 130

Length of support pin

35 40 50 60 70 80
B DIMM 90 100 110 120 130 130 140 150 160 170 180
190 200 210 220 230 240
250 260 270 280 290 300
C DIMM 70 80 90 100 110
310 320 330 340 350 360
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 350

X 400 U DIMM Specification of ejector

V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate 3

0
■ How to order optional specification 5
■ Order example MDC HB 3055 50 60 70 S V M N IH 280:190 / R25 / S40 / #FK 5
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 30 A 30 45
10
A 30 45

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

695
 H Series 3060
TW Clamping plate spec. TW
300 Clamping type 350
58 180 58 Bolt-fastening type 400

M24

248
210
576
546
496
486
420

550
600
208
246
30
Support pin

30
20 Guide pin
Return pin

110
6-M16 156
20 180 Datum plane
Puller bolt
234
4-M10
250
266
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 30 A 30 45
10
B A 30 45

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
20

20
C
C

25

25
30
30

696
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3060 50 50 80 S V M N IH 280:190 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260 280
35 40 50 60 70 80
A DIMM 90 100 110 120 130

Length of support pin

35 40 50 60 70 80
B DIMM 90 100 110 120 130 130 140 150 160 170 180
190 200 210 220 230 240
250 260 270 280 290 300
C DIMM 70 80 90 100 110
310 320 330 340 350 360
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 350

X 400 U DIMM Specification of ejector

V 45 M Counterbore type
Y 350
W 60 L Spacer type

Z 400 — Types without backing plate 3

0
■ How to order optional specification 6
■ Order example MDC HB 3060 50 60 70 S V M N IH 280:190 / R25 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 30 A 30 45
10
A 30 45

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

697
 H Series 3350
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550
TW
330
58 210 58
M24

198
160

450
500
476
446
396
386
320

158
30

196
Support pin

20 30
Guide pin
Return pin

140
6-M16 186
20 210 Datum plane
Puller bolt
264
4-M10
280
296

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 30 A 30 45
10
B A 30 45

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

U
20

20
C
C

25

25
30
30

698
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3350 50 50 80 S V M N IH 280:190 Option

Type HA HB HC HD Length of puller bolt

130 140 150 160 170
Nominal dimension 180 190 200 220 240
260 280
35 40 50 60 70 80
A DIMM 90 100 110 120 130

Length of support pin

35 40 50 60 70 80
B DIMM 90 100 110 120 130 130 140 150 160 170 180
190 200 210 220 230 240
250 260 270 280 290 300
C DIMM 70 80 90 100 110
310 320 330 340 350 360
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 400

X 550 U DIMM Specification of ejector

V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate 3

3
■ How to order optional specification 5
■ Order example MDC HB 3350 50 60 70 S V M N IH 280:190 / R25 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R25 Changes the Plate R thickness 30 to 25 ※
Changes the Plate S thickness 30 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 30 A 30 45
10
A 30 45

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

699
 H Series 3550
Clamping plate spec. TW
Clamping type 400
Bolt-fastening type 550
TW
350
63 220 63
M24

183
143
476
446
366
286

440
500
141
35

181
Support pin

35
Guide pin

20
Return pin

158
6-M16 196
25 204 Datum plane
Puller bolt
274
4-M10
290
310

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 35 A 35 50
10
B A 35 50

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

20
20

C
C

25
25

30
30

700
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3550 50 50 80 S V M N IH 290:190 Option

Type HA HB HC HD Length of puller bolt

150 160 170 180 190
Nominal dimension 200 220 240 260 280
300
40 50 60 70 80 90
A DIMM 100 110 120 130

Length of support pin

40 50 60 70 80 90
B DIMM 100 110 120 130 160 170 180 190 200 210
220 230 240 250 260 270
280 290 300 310 320 330
C DIMM 70 80 90 100 110
340 350 360 380 400
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 400

X 550 U DIMM Specification of ejector

V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate 3

5
■ How to order optional specification 5
■ Order example MDC HB 3550 50 60 70 S V M N IH 280:190 / R30 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 35 A 35 50
10
A 35 50

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

701
 H Series 3555
Clamping plate spec. TW
TW Clamping type 400

350 Bolt-fastening type 550

63 220 63
M24

208
168
526
496
416
336

490
550
166
35

206
Support pin

35
Guide pin

20
Return pin

158
6-M16 196
25 204 Datum plane
Puller bolt
274
4-M10
290
310

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 35 A 35 50
10
B A 35 50

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

20
20

C
C

25
25

30
30

702
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3555 50 50 80 S V M N IH 290:190 Option

Type HA HB HC HD Length of puller bolt

150 160 170 180 190
Nominal dimension 200 220 240 260 280
300
40 50 60 70 80 90
A DIMM 100 110 120 130

Length of support pin

40 50 60 70 80 90
B DIMM 100 110 120 130 160 170 180 190 200 210
220 230 240 250 260 270
280 290 300 310 320 330
C DIMM 70 80 90 100 110
340 350 360 380 400
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 400

X 550 U DIMM Specification of ejector

V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate 3

5
■ How to order optional specification 5
■ Order example MDC HB 3555 50 60 70 S V M N IH 280:190 / R30 / S40 / #FK 5
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 35 A 35 50
10
A 35 50

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

703
 H Series 3560
TW Clamping plate spec. TW
350 Clamping type 400
63 220 63 Bolt-fastening type 550

M24

233
193
576
546
466
386

540
600
191
231
35
Support pin

35
Guide pin

20
Return pin

158
6-M16 196
25
Puller bolt
204 Datum plane
274
4-M10
290
310
※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 35 A 35 50
10
B A 35 50

Plate R
Plate R
Length of puller bolt

Plate S
puller bolt
Length of
U

20
20

C
C

25
25

30
30

704
TD Technical Data P.787

■ How to order

■ Order example MDC HA 3560 50 50 80 S V M N IH 290:190 Option

Type HA HB HC HD Length of puller bolt

150 160 170 180 190
Nominal dimension 200 220 240 260 280
300
40 50 60 70 80 90
A DIMM 100 110 120 130

Length of support pin

40 50 60 70 80 90
B DIMM 100 110 120 130 160 170 180 190 200 210
220 230 240 250 260 270
280 290 300 310 320 330
C DIMM 70 80 90 100 110
340 350 360 380 400
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 400

X 550 U DIMM Specification of ejector

V 45 M Counterbore type
Y 400
W 60 L Spacer type

Z 550 — Types without backing plate 3

5
■ How to order optional specification 6
■ Order example MDC HB 3560 50 60 70 S V M N IH 280:190 / R30 / S40 / #FK 0
Code Description Code Description
#FK Removes the threaded holes for eye bolts for Plate B R30 Changes the Plate R thickness 35 to 30 ※
Changes the Plate S thickness 35 to
Plate S Thickness
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 35 A 35 50
10
A 35 50

Plate R
Plate R
Plate S
puller bolt
Length of

puller bolt
Length of
B

20
20
C

25
25
30

30

705
 H Series 4060
HT DIMM FK Clamping plate spec. TW
80∼265 Ｍ24 Clamping type 450
270∼425 Ｍ30 Bolt-fastening type 550
TW
400
68 260 68
FK

233
193
574
546
466
386

540
600
191
35

231
Support pin
35
Guide pin
20
Return pin

198
6-M16 234
25 254 Datum plane
Puller bolt
324
4-M12
340
360

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 35 A 35 50
10
B A 35 50

Plate R
Plate R
Length of puller bolt

Plate S
HT
HT

puller bolt
Length of
U

25
25

C
C

30
30

35
35

706
TD Technical Data P.787

■ How to order

■ Order example MDC HA 4060 70 70 10 S V M N IH 350:240 Option

Type HA HB HC HD Length of puller bolt

150 160 170 180 190
Nominal dimension 200 220 240 260 280
300
40 50 60 70 80 90
A DIMM 100 110 120 130

Length of support pin

40 50 60 70 80 90
B DIMM 100 110 120 130 160 170 180 190 200 210
220 230 240 250 260 270
280 290 300 310 320 330
C DIMM 100 110 120 130
340 350 360 380 400
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 450

X 550 U DIMM Specification of ejector

V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate 4

0
■ How to order optional specification 6
■ Order example MDC HB 4060 70 60 10 S V M N IH 350:240 / R30 / S50 / #FK 0
Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FK Removes the threaded holes for eye bolts for Plate A and B
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 35 A 35 50
10
A 35 50

Plate R
Plate R
Plate S
HT
puller bolt
HT

Length of

puller bolt
Length of
B

25
25
C

30
30
35

35

707
 H Series 4070
HT DIMM FK Clamping plate spec. TW
80∼195 Ｍ24 TW Clamping type 450
200∼425 Ｍ30 400 Bolt-fastening type 550
68 260 68
FK

283
243
674
646
566
486

640
700
241
281
35
Support pin
35
Guide pin
20
Return pin

198
6-M16 234
25 254 Datum plane
Puller bolt
324
4-M12
340
360

※ Please note that the 2D diagrams in this catalog are created with isometric images, but not accurate.

HAtype HBtype
10
B 35 A 35 50
10
B A 35 50

Plate R
Plate R
Length of puller bolt

Plate S
HT
HT

puller bolt
Length of
U

25
25

C
C

30
30

35
35

708
TD Technical Data P.787

■ How to order

■ Order example MDC HA 4070 70 70 10 S V M N IH 350:240 Option

Type HA HB HC HD Length of puller bolt

150 160 170 180 190
Nominal dimension 200 220 240 260 280
300
40 50 60 70 80 90
A DIMM 100 110 120 130

Length of support pin

40 50 60 70 80 90
B DIMM 100 110 120 130 160 170 180 190 200 210
220 230 240 250 260 270
280 290 300 310 320 330
C DIMM 100 110 120 130
340 350 360 380 400
※ If A, B and C dimension are 3 digits, specify the dimension with the
first two-digit numbers. e.g.:（100→ 10 ）

Width of clamping Orientation of This may be changed to J or P by

H series
3-Plate Type
plate guide Futaba if there is any addition or
change to the specification.
S 450

X 550 U DIMM Specification of ejector

V 50 M Counterbore type
Y 450
W 70 L Spacer type

Z 550 — Types without backing plate 4

0
■ How to order optional specification 7
■ Order example MDC HB 4070 70 60 10 S V M N IH 350:240 / R30 / S50 / #FK 0
Code Description Code Description
#FA Removes the threaded holes for eye bolts for Plate A R30 Changes the Plate R thickness 35 to 30 ※

#FB Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FK Removes the threaded holes for eye bolts for Plate A and B
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
※ If the thickness of a runner plate (Plate R) becomes thinner, the guide bushing and the length of the guide part shorten.

HCtype HDtype
10
B 35 A 35 50
10
A 35 50

Plate R
Plate R
Plate S
HT
puller bolt
HT

Length of

puller bolt
Length of
B

25
25
C

30
30
35

35

709
710
 CASSETTE MOLD BASES
Cassette Mold Bases
■QMC

 Overview and Systematic Diagram ・・・・・・・・・・・・・・・・・・・・・ P.712

 Holder Overview ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.714

 Insert Unit - Overview and Parts ・・・・・・・・・・・・・・・・・・・・・・・ P.716

 Request a Catalog ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.718

■Sumitomo Cassette Mold Base

 Overview ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.720

 Request a Catalog ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.722

■NISSEI FP SYSTEM

 Overview ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.724

 Request a Catalog ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.725
 Overview & Systematic Diagram
R

A high precision insert

R A versatile holder that unit with an extensive
can be mounted on product variations of
every molding machine over 2,000 types

QMC enables you to:

Mold design Mold production Mold setup Mold management
・Mold design ・Mold production ・A skilled person ・A Save on
completes only completes only
is not required storage space
with the with the
designing of the machining of the ・Precise setup is ・Precise setup is
product section product section assured assured

・Reduce production
・Reduce design time lead time ・Reduce mold ・Handle molds easily
changeover time
・Cut production costs
※QMC is a registered trade mark of Futaba Corporation.

712
■Systematic diagram

Type B holder Type A holder

Type of holders
(For 2-plate mold only) (For both 2 & 3 plate molds only)

Insert unit for Insert unit for

Gate system 2-plate mold 3-plate mold

Size of
mold plates 130 X 130 150 X 150 150 X 180
Specification and selection of insert units

Cassette Mold Bases

Thickness of
20 25 30 35 40
mold plates

Ejector pin Stripper plate Ejector sleeve

Ejection type
ejection type ejection type ejection type
※1

Material of
F -S55C HPM1 AAS
mold plates
※2

※1. This can be used only on the holder with an adapter plate
※2. AAS: aluminum alloy (JIS A7075 equivalent)

713
 Holder overview
R

Type B for 2-plate mold base

Clamp lever
Unclamped state Clamped state
Tuning the handle shaft will push
down the clamp lever via an
eccentric shaft and lock the
clamping and backing plates into
place.

Adapter plate The size of the insert unit is indicated.

This plate is removed when This stopper is used by turning around according to the
size of mold plates.
sleeve ejection is used, and the
core pin plate of the insert unit is
installed. and core pin plate of
When turning the handle
the insert unit is installed.
shaft, the yellow indicator
Heat insulator sheet turns into black, indicating
that the holder is clamped.

Operation
confirmation
window

I.U. stopper

Special T-shaped
wrench
Positioning pin
Sub guide way When turning the handle shaft, the
This is used as a guide when
positioning pin protrudes from the Handle shaft
installing the movable insert unit. Two handle shafts are provided on the operating sides of the
holder and penetrates the
positioning hole. fixed and movable holders respectively. Turning the handle
shaft with a special T-shaped wrench will activate the
positioning pin and the clamp lever at the same time. This
Adapter plate fixing screw
handle shaft is designed to tighten automatically and self-lock
By turning the screws just one turn, you can fix the
with a spring force acting in that direction for increased safety.
adapter plate or core pin plate securely.
Therefore, it is not necessary to tighten the shaft with a strong
force.

※The picture shows a holder with an adapter plate (optional).

Features of holders
■Realize high cost performance ■High precision positioning
・A versatile holder designed for 2-plate mold only. The positioning of the insert unit is kept precise by the positioning

・Three different sizes of insert units can be mounted, which

pin, which protrudes from the holder and penetrates the
positioning hole of the insert unit.
enables the production of a variety of molded products.
■Mold changeover with a simple
Simply by side loading the insert unit from the operating side and
■Support generally used molding turning the handle shaft with the T-shaped wrench, it will be
This holder supports 25 to 50 ton horizontal and vertical injection
securely clamped (the clamp lever will be depressed by an
molding machines manufactured by each maker.
eccentric cam engaging with the positioning pin). It can also be
easily unclamped.
714
 Type A for both 2 & 3 plate molds
Clamp lever
Tuning the handle shaft will push down
the clamp lever via an eccentric shaft
and lock the clamping and backing
plates into place.

Adapter plate The size of the insert unit is indicated. For 2-plate molding, the cavity plate
This plate is removed when This stopper is used by turning around according to the (fixed half) and clamping plate are
size of mold plates. fastened.
sleeve ejection is used, and the
core pin plate of the insert unit
is installed. and core pin plate of
Strap
the insert unit is installed.

Heat insulator sheet

Special T-shaped wrench

I.U. stopper
Unclamped state Clamped state

Ejector pin

Cassette Mold Bases

Runner lock pin
Operation confirmation
When turning the handle
Sub guide way Positioning pin window shaft, the yellow indicator
This is used as a guide when When turning the handle shaft, the turns into black, indicating
installing the movable insert unit. that the holder is clamped.
positioning pin protrudes from the
holder and penetrates the
positioning hole. Handle shaft
Adapter plate fixing screw Two handle shafts are provided on the operating sides of the fixed and
By turning the screws just one turn, you can fix the movable holders respectively. Turning the handle shaft with a special
adapter plate or core pin plate securely. T-shaped wrench will activate the positioning pin and the clamp lever at
the same time. This handle shaft is designed to tighten automatically and
self-lock with a spring force acting in that direction for increased safety.
Therefore, it is not necessary to tighten the shaft with a strong force.

Features of holders
■Support multiple applications ■High precision positioning
・Three different sizes of insert units can be mounted, which The positioning of the insert unit is kept precise by the positioning
enables the production of a variety of molded products. pin, which protrudes from the holder and penetrates the

・Puller bolts, runner lock pins and ejector pins that support both positioning hole of the insert unit.
the 2 & 3 plate molds are installed.
■Mold changeover with a simple operation
・This holder has a mechanism to fasten an ejector plate for sleeve Simply by side loading the insert unit from the operating side and
ejection easily and securely, which also supports sleeve ejection. turning the handle shaft with the T-shaped wrench, it will be
securely clamped (the clamp lever will be depressed by an
■Support generally used molding machine eccentric cam engaging with the positioning pin). It can also be
This holder supports 25 to 50 ton horizontal and vertical injection
easily unclamped.
molding machines manufactured by each maker. 715
 Insert Unit Overview and Parts
R

Return spring Temperature control hole

Material
In addition to F-S55C, prehardened
steel and aluminum alloy can be
selected.

Datum planes
These two right-angled side surfaces
are machined accurately. All holes
are machined by using these
Steel handle surfaces as reference surfaces. Positioning hole
These right-angled two side surfaces are machined Roughness of finished surface is increased
accurately. All holes are machined by using these by burnishing in order to enhance wear
surfaces as reference surfaces. resistance.

Features of insert units

■A broad range of selections and options ■Realize reduction in both lead time and cost
・Mold plates are available in 3 sizes: 130×130, 150×150 and As parting locks and springs are installed, and temperature control
150×180. channels are machined, mold production will be completed only by

・The thickness of the mold plates can be selected from 20, 25, 30, 35 and 40.
machining the product section. In addition, it is not necessary to install
runner lock pins, spring pins and puller bolts, as they are already
・Three ejection methods are available: ejector pin, stripper plate mounted, which leads to a significant reduction in production costs.
and ejector sleeve.
■Easy handling
・Three different materials of mold plates are available: As the hole-basis system of fits is used for this insert unit,
F-S55C, HPM1 and AAS (aluminum alloy A7075 equivalent),
no precision defect is caused due to foreign matters, etc. on the
which can be selected from.
abutting surface and it is not necessary to protect datum planes
■2-plate and 3-plate sharing type during storage.
The mold configuration is the same for both 2-plate mold and
3-plate mold. Parting locks are installed for 3-plate mold.

716
Maintenance parts and components

M-SBA sprue bushing Material SK3

M5 bolt hole

-0.011
0
φ13
φ36

φd
26

2°
15 +0.3
+0.2

+0.6
L +0.4

Note 1. This sprue bushing is installed in the insert unit when a combination of a ■Dimension & price list (in yen)
Type A holder and a 2-plate mold is used.
L 35 40 45 50 55
Note 2. For sprue bushing to install on the insert unit accompanying a Type B holder, please refer to
the separate volume “Additional Mold Base Processing & Mold Parts Edition”. d 3.5 4.5 3.5 4.5 3.5 4.5 3.5 4.5 3.5 4.5
Nominal code of d A B A B A B A B A B
Price (in yen) 3,800 3,900 4,000 4,100

■How to order

■Order example M- SBA13 X 40 X A QM

Cassette Mold Bases

L DIMM Nominal code of d

M-PLLA Parting locks Material PAR (plastic sleeve) SCM435 (taper bolt)

①Taper bolt ②Plastic sleeve

17 M5
φ8.5
φ10

4 2 24

■Price ①+② 600 yen ①200 yen  ②400 yen

■How to order

①＋②M- PLLA10
①M- PLLS10
②M- PLLM5
717
 Request a catalog
R

CATALOG ORDER A catalog with

R

specifications is

718
 Cassette Mold Bases

719
available.
 Sumitomo Cassette Mold Base Overview
About cassette holders
■ These holders are designed based on the micro injection molding machine MINIMAT (Sumitomo Heavy Industries, Ltd.)
specifications and support horizontal molding machines with a clamping force ranging from 8 ton to 25 ton which are
manufactured by each maker. The holders are available in two types: split mold holders and standard type holders.
■ The split type holder is fitted with slide cores and angular pins that are required for undercut processes. Therefore, the
split type mold (slide type mold), which have been difficult to support on the traditional cassette type holder, can now be
used in the same way as other common 2-plate and 3-plate type molds.
■ The standard type holders for the MINIMAT M5/7 and M8/7 molding machines have become more squre shaped in
accordance with the tie bar spacing so that it can produce larger molded products for increased versatility.
■ The holders for the MINIMAT M26/15 molding machine adopts the same size for both the standard type and split type to
allow the accompanying insert molds to have compatibility.

List of insert molds and holder types

Injection molding machine Holders Insert molds

MINIMAT Standard type 2-plate

M5/7
M8/7

Split type 2-plate

MINIMAT Standard type

M26/15

720 Split type 2-plate

Features of insert molds
■ The insert molds for the MINIMAT M5/7 and M8/7 are available in two sizes, 120×120 and 120×170 and three types, 2-plate mold, 3-plate
mold base and split mold (120×170 size only) (5 types in total) in order to support the production of a broader range of molded products.
■ The insert molds for the MINIMAT M26/15 are available in one size, 150×200 and three types, 2-plate mold, 3-plate
mold and split mold (3 types in total) and adopts common layouts for pins, etc. for more ease of use.
■ As the 3-plate type split mold is equipped with piece molds for cavity, bobbin shape, etc. can be easily produced with molds.
■ As puller bolts, parting locks and springs required for molding operations are installed and temperature control channel
are also machined, molds can be produced only by machining the product sections.
■ The 3-plate type insert molds are designed to allow larger amount of mold opening by using guide pins longer than the thickness of the mold.
■ Prehardened steel (38HRC) is used for mold plates and runner plates to increase strength and wear resistance.
■ The insert molds can be mounted on molding machines only by inserting along the grooves provided on the holder.

Insert mold

3-plate

3-plate Split type Cassette Mold Bases

Sumitomo Cassette Mold Base

※This insert mold cannot be

3-plate Split type used with the standard type 721
 Sumitomo Cassette Mold Base – Catalog Request
CATALOG ORDER A catalog with Sumitomo cassette mold

722
base specifications is available.

Cassette Mold Bases住友カセットモールドベース

723
 NISSEI FP SYSTEM

Reduce mold design & machining Reduce molding setup time dramatically
time significantly & improve quality with a one touch mold changeover
■ In the FP system, the unit mold (U.M) is standardized,
so mold design time will be significantly reduced. In
addition, the mold production completes only by
machining the product section. U.M

■ A significant reduction in mold weight will cut the

time required for transportation, centering and mold
assembling work, etc., resulting in increased
uptime of machining machines. ■ The production of parts can be changed over only by
switching the U.M. In addition, this can be done by
hand easily.
【FP system】 【Traditional molds】
■ The cooling circuit will be automatically connected
Order U.M base Nesting
upon installation. Traditional piping work is not
necessary (FP connector for cooling is used).
Contour finishing
■ The maintenance is easy and substantial reduction in
Base machining setup time will increase the uptime of molding
machine.
Machine product section Machine product section

Mold assembling

Completion of molding
724
A catalog with NISSEI FP SYSTEM specifications
is available.

CATALOG ORDER

Cassette Mold Bases

N
I
S
S
E
I
F
P
S
Y
S
T
E
M

725
726
 CAVITY RETAINER SETS
Cavity Retainer Sets
■Features ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.728

■Specification and Selection ・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.729

■Cavity Retainer Set

  Width 150 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.730

  Width 180 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.732
  Width 200 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.734
  Width 230 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.736
  Width 250 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.738
  Width 270 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.740
  Width 290 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.742
  Width 300 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.744
  Width 330 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.746
  Width 350 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.748
  Width 400 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.750
  Width 450 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.752
  Width 500 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.754
  Width 600 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.756

■Cavity Retainer Set Material Change Option ・・・・・・・・・・・・・・ P.758

 Cavity
Retainer Sets Features
● Carefully selected materials used
● Consistent quality
● A broad range of size
● Low price and short delivery time

❶ This guide, which is installed with a different pitch, prevents improper installation.
❷ Squareness datum planes are clearly marked with . As the planes are simultaneously machined, there is no datum plane
deviation.
❸ Threaded holes for eye bolts are machined in this direction and at the symmetrical position.
❹ For cavity plates, F-S55C is used (if the thickness is 25 mm or less, F-S50C is used).

728
 Cavity
Retainer Sets Specification & Selection
■ Inner or outer position installation specification of guide pins
For the installation positions of guide pins, two types of specifications are available: inner and outer positions. Please select one of them.

● Code I: Installs guide pins at the inner position ● Code O: Install guide pins at the outer positions

■ Simplified weight calculation table

Use this formula when calculating approx. weight of standard cavity retainer set.

● Weight calculation W= a×T

formula W : weight (kg)
ａ : weight coefficient
T : thickness of cavity retainer set (mm)
T

● Weight coefficient table

Cavity Retainer Sets

Nominal dimension Weight coefficient (a) Nominal dimension Weight coefficient (a) Nominal dimension Weight coefficient (a) Nominal dimension Weight coefficient (a)
1515 0.18 2035 0.55 2935 0.80 3555 1.51
1518 0.21 2323 0.42 2940 0.91 3560 1.65
1520 0.24 2325 0.45 3030 0.71 4040 1.26
1523 0.27 2327 0.49 3032 0.75 4045 1.41
1525 0.29 2330 0.54 3035 0.82 4050 1.57
Features, Specification & Selection

1530 0.35 2335 0.63 3040 0.94 4055 1.73

1818 0.25 2525 0.49 3045 1.06 4060 1.89
1820 0.28 2527 0.53 3050 1.18 4545 1.59
1823 0.32 2530 0.59 3335 0.91 4550 1.77
1825 0.35 2535 0.69 3340 1.04 4555 1.94
1830 0.42 2540 0.79 3345 1.17 4560 2.12
1835 0.49 2545 0.88 3350 1.30 5050 1.96
2020 0.31 2730 0.63 3535 0.96 5060 2.36
2023 0.36 2735 0.74 3540 1.10 6060 2.83
2025 0.39 2740 0.85 3545 1.24 6070 3.30
2030 0.47 2930 0.68 3550 1.37

729
 Cavity
Retainer Sets Width 150
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
150 150

A
114 114
M12 M12

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

16 Plate S
16

15
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
1515 150 55 57 114 – – –
1518 180 70 72 144 24 26 52
1520 200 80 82 164 34 36 72
1523 230 95 97 194 49 51 102
1525 250 105 107 214 59 61 122
1530 300 130 132 264 84 86 172
※ For nominal dimension 1515, the inner position installation specification of guide pins is not available.

■ Combinations of A dimensions and B dimensions

● Combination table for cavity plates with a nominal dimension 1515, 1518, 1520, 1523 or 1525
A DIMM 20 25 30 35 40 50 60
20 20 20 20 20
25 25 25 25 25 25
30 30 30 30 30 30 30
B DIMM 35 35 35 35 35 35 35
40 40 40 40 40 40 40
50 50 50 50 50 50 50
60 60 60 60 60

● Combination table for cavity plates with a nominal dimension 1530

A DIMM 20 25 30 35 40 50 60 70 80
20 20 20 20 20
25 25 25 25 25 25
30 30 30 30 30 30 30
35 35 35 35 35 35 35 35
B DIMM 40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60
70 70 70 70 70 70
80 80 80 80 80

730
TD Technical Data P.787

■ How to order

■ Order example MDB – A 1518 50 40 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 1520 30 50 S O N / S30 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
Changes the material of Plate A, S or B
Material ※Applicable to 1515, 1518, 1520, and 1523 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

1
5
0

731
 Cavity
Retainer Sets Width 180
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
180 180

A
134 140
M12 M12

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

20 Plate S
20

15
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
1818 180 65 67 134 – – –
1820 200 75 77 154 21 23 46
1823 230 90 92 184 36 38 76
1825 250 100 102 204 46 48 96
1830 300 125 127 254 71 73 146
1835 350 150 152 304 96 98 196
※ For nominal dimension 1818, the inner position installation specification of guide pins is not available.

■ Combinations of A dimensions and B dimensions

A DIMM 20 25 30 35 40 50 60 70 80
20 20 20 20 20
25 25 25 25 25 25
30 30 30 30 30 30 30
35 35 35 35 35 35 35 35
B DIMM 40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60
70 70 70 70 70 70
80 80 80 80 80

732
TD Technical Data P.787

■ How to order

■ Order example MDB – A 1820 50 40 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 1825 30 50 S O N / S30 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 15 to
20 , 30 or 40
Changes the material of Plate A, S or B
Material ※Applicable to 1818, 1820, 1823 and 1825 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

1
8
0

733
 Cavity
Retainer Sets Width 200
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
200 200

A
154 154
M12 M12

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

20 Plate S
20

20
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
2020 200 75 77 154 21 23 46
2023 230 90 92 184 36 38 76
2025 250 100 102 204 46 48 96
2030 300 125 127 254 71 73 146
2035 350 150 152 304 96 98 196

■ Combinations of A dimensions and B dimensions

● Combination table for cavity plates with a nominal dimension 2020
A DIMM 20 25 30 35 40 50 60 70 80
20 20 20 20 20
25 25 25 25 25 25
30 30 30 30 30 30 30
35 35 35 35 35 35 35 35
B DIMM 40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60
70 70 70 70 70 70
80 80 80 80 80

● Combination table for cavity plates with a nominal dimension 2023

A DIMM 25 30 35 40 50 60 70 80
25 25 25 25 25
30 30 30 30 30 30
35 35 35 35 35 35 35
40 40 40 40 40 40 40 40
B DIMM 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60
70 70 70 70 70 70
80 80 80 80 80

734
TD Technical Data P.787

■ How to order

■ Order example MDB – A 2025 50 40 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 2030 30 50 S O N / S30 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
Changes the material of Plate A, S or B
Material ※Applicable to 2020, 2023, 2025 and 2030 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

● Combination table for cavity plates with a nominal dimension 2025, 2030, or 2035
A DIMM 25 30 35 40 50 60 70 80 90 100
25 25 25 25 25
30 30 30 30 30 30
35 35 35 35 35 35 35

Cavity Retainer Sets

40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
B DIMM
60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70
80 80 80 80 80 80 80
90 90 90 90 90 90
100 100 100 100 100 100
Width

2
0
0

735
 Cavity
Retainer Sets Width 230
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
230 230

A
184 184
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

20 Plate S
20

20
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
2323 230 90 92 184 35 37 74
2325 250 100 102 204 45 47 94
B ≦ 40 → M12
2327 270 110 112 224 54 56 112
B ≧ 50 → M16
2330 300 125 127 254 69 71 142
2335 350 150 152 304 94 96 192

■ Combinations of A dimensions and B dimensions

A DIMM 25 30 35 40 50 60 70 80 90 100
25 25 25 25 25
30 30 30 30 30 30
35 35 35 35 35 35 35
40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
B DIMM
60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70
80 80 80 80 80 80 80
90 90 90 90 90 90
100 100 100 100 100 100

736
TD Technical Data P.787

■ How to order

■ Order example MDB – A 2325 50 40 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 2330 30 50 S O N / S30 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 20 to
30 , 40 or 50
Changes the material of Plate A, S or B
Material ※Applicable to 2323, 2325, 2327 and 2330 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

2
3
0

737
 Cavity
Retainer Sets Width 250
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
250 250

A
194 194
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

25 Plate S
25

25
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
2525 250 95 97 194 33 35 70
B ≦ 40 → M12
2527 270 105 107 214 43 45 90
B ≧ 50 → M16
2530 300 120 122 244 58 60 120
2535 350 145 147 294 83 85 170
2540 400 170 172 344 108 110 220 M16
2545 450 195 197 394 133 135 270

■ Combinations of A dimensions and B dimensions

● Combination table for cavity plates with a nominal dimension 2525
A DIMM 25 30 35 40 50 60 70 80 90 100
25 25 25 25 25
30 30 30 30 30 30
35 35 35 35 35 35 35
40 40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
B DIMM
60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70
80 80 80 80 80 80 80
90 90 90 90 90 90
100 100 100 100 100 100

● Combination table for cavity plates with a nominal dimension 2527, 2530, 2535, 2540 or 2545
A DIMM 30 35 40 50 60 70 80 90 100 110 120
30 30 30 30 30
35 35 35 35 35 35
40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60 60
B DIMM 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

738
TD Technical Data P.787

■ How to order

■ Order example MDB – A 2530 40 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 2540 40 50 S O N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50
Changes the material of Plate A, S or B
Material ※Applicable to 2525, 2527, 2530 and 2535 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

2
5
0

739
 Cavity
Retainer Sets Width 270
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
270 270

A
214 214
M16 M16

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

25 Plate S
25

25
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
2730 300 120 122 244 58 60 120
2735 350 145 147 294 83 85 170
2740 400 170 172 344 108 110 220

■ Combinations of A dimensions and B dimensions

A DIMM 30 35 40 50 60 70 80 90 100 110 120

30 30 30 30 30
35 35 35 35 35 35
40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60 60
B DIMM 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

740
TD Technical Data P.787

■ How to order

■ Order example MDB – A 2730 60 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 2740 40 50 S O N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

2
7
0

741
 Cavity
Retainer Sets Width 290
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
290 290

A
234 234
M16 M16

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

25 Plate S
25

25
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
2930 300 120 122 244 58 60 120
2935 350 145 147 294 83 85 170
2940 400 170 172 344 108 110 220

■ Combinations of A dimensions and B dimensions

A DIMM 30 35 40 50 60 70 80 90 100 110 120

30 30 30 30 30
35 35 35 35 35 35
40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60 60
B DIMM 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

742
TD Technical Data P.787

■ How to order

■ Order example MDB – A 2930 60 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 2935 40 50 S O N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 25 to
30 , 40 or 50

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

2
9
0

743
 Cavity
Retainer Sets Width 300
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
300 300

A
234 234
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

30 Plate S
30

30
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
3030 300 115 117 234 47 49 98
3032 320 125 127 254 57 59 118 M16
3035 350 140 142 284 72 74 148
3040 400 165 167 334 97 99 198
3045 450 190 192 384 120 122 244 M20
3050 500 215 217 434 145 147 294

■ Combinations of A dimensions and B dimensions

● Combination table for cavity plates with a nominal dimension 3030
A DIMM 30 35 40 50 60 70 80 90 100 110 120
30 30 30 30 30
35 35 35 35 35 35
40 40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60 60
B DIMM 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

● Combination table for cavity plates with a nominal dimension 3032, 3035, 3040, 3045 or 3050
A DIMM 35 40 50 60 70 80 90 100 110 120
35 35 35 35 35
40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70
B DIMM
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

744
TD Technical Data P.787

■ How to order

■ Order example MDB – A 3040 60 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 3035 40 50 S O N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60
Changes the material of Plate A, S or B
Material ※Applicable to 3030, 3035 and 3040 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

3
0
0

745
 Cavity
Retainer Sets Width 330
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
330 330

A
264 264
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

30 Plate S
30

30
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
3335 350 140 142 284 72 74 148
3340 400 165 167 334 97 99 198 M20
3345 450 190 192 384 120 122 244
3350 500 215 217 434 145 147 294 M24

■ Combinations of A dimensions and B dimensions

A DIMM 35 40 50 60 70 80 90 100 110 120

35 35 35 35 35
40 40 40 40 40 40 40
50 50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70
B DIMM
80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100
110 110 110 110 110 110 110
120 120 120 120 120 120 120

746
TD Technical Data P.787

■ How to order

■ Order example MDB – A 3340 60 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 3335 80 60 S O N / S40 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 30 to
40 , 50 or 60

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

3
3
0

747
 Cavity
Retainer Sets Width 350
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
350 350

A
GPW GPW
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

GP Plate S
GP

35
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L GPW GP FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
3535 350 140 142 284 70 72 144
M20
3540 400 284 165 167 334 95 97 194 30
3545 450 190 192 384 120 122 244
3550 500 210 212 424 132 134 268
M24
3555 550 274 235 237 474 157 159 318 35
3560 600 260 262 524 182 184 368

■ Combinations of A dimensions and B dimensions

A DIMM 40 50 60 70 80 90 100 110 120 130

40 40 40 40 40 40
50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80 80
B DIMM
90 90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100 100
110 110 110 110 110 110 110 110
120 120 120 120 120 120 120 120
130 130 130 130 130 130 130

748
TD Technical Data P.787

■ How to order

■ Order example MDB – A 3540 60 50 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 3350 80 60 S O N / S50 / #FK

Code Description Code Description

#FK Removes the threaded holes for eye bolts for Plate B
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
Changes the material of Plate A, S or B
Material ※ Applicable to 3540 Specifications other than the above are also available.
change Additional
※Details ☞ P.758 Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

3
5
0

749
 Cavity
Retainer Sets Width 400
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
400 400

A
324 324
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

35 Plate S
35

35
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
4040 400 160 162 324 82 84 168
4045 450 185 187 374 107 109 218 M24
4050 500 210 212 424 132 134 268
4055 550 235 237 474 157 159 318 B ＝ 40 → M24
4060 600 260 262 524 182 184 368 B ≧ 50 → M30

■ Combinations of A dimensions and B dimensions

A DIMM 40 50 60 70 80 90 100 110 120 130

40 40 40 40 40 40
50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80 80
B DIMM
90 90 90 90 90 90 90 90 90
100 100 100 100 100 100 100 100 100
110 110 110 110 110 110 110 110
120 120 120 120 120 120 120 120
130 130 130 130 130 130 130

750
TD Technical Data P.787

■ How to order

■ Order example MDB – A 4045 80 70 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 4050 100 80 S O N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 35 to
40 , 50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Changes the material of Plate A, S or B
#FK Removes the threaded holes for eye bolts for Plate A and B Material change ※Applicable to 4040
※Details ☞ P.758

Additional Specifications other than the above are also available.

Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

4
0
0

751
 Cavity
Retainer Sets Width 450
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
450 450

A
364 364
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

40 Plate S
40

40
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
4545 450 180 182 364 95 97 194 B ＝ 40 → M24
4550 500 205 207 414 120 122 244 B ≧ 50 → M30
4555 550 230 232 464 145 147 294
M30
4560 600 255 257 514 170 172 344

■ Combinations of A dimensions and B dimensions

A DIMM 40 50 60 70 80 90 100 110 120 130 140 150

40 40 40 40 40 40
50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90 90 90 90
B DIMM
100 100 100 100 100 100 100 100 100 100 100
110 110 110 110 110 110 110 110 110 110
120 120 120 120 120 120 120 120 120 120
130 130 130 130 130 130 130 130 130
140 140 140 140 140 140 140 140 140
150 150 150 150 150 150 150 150

752
TD Technical Data P.787

■ How to order

■ Order example MDB – A 4550 80 70 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 4560 100 80 S O N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
#FK Removes the threaded holes for eye bolts for Plate A and B processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

4
5
0

753
 Cavity
Retainer Sets Width 500
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
500 500

A
414 414
FK FK

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

40 Plate S
40

40
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L FK
dimension GP1 GP2 GP3 GP4 GP5 GP6
5050 500 205 207 414 120 122 244 M30
5060 600 255 257 514 170 172 344 B ≦ 100 → M30 B ≧ 110 → M36

■ Combinations of A dimensions and B dimensions

A DIMM 40 50 60 70 80 90 100 110 120 130 140 150

40 40 40 40 40 40
50 50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90 90 90 90
B DIMM
100 100 100 100 100 100 100 100 100 100 100
110 110 110 110 110 110 110 110 110 110
120 120 120 120 120 120 120 120 120 120
130 130 130 130 130 130 130 130 130
140 140 140 140 140 140 140 140 140
150 150 150 150 150 150 150 150

754
TD Technical Data P.787

■ How to order

■ Order example MDB – A 5050 80 70 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 5060 100 80 S O N / S50 / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A
Plate S Thickness
Changes the Plate S thickness 40 to
50 or 60
#FB Removes the threaded holes for eye bolts for Plate B
Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
#FK Removes the threaded holes for eye bolts for Plate A and B processing Processing & Mold Parts Edition”for details.

Cavity Retainer Sets

Width

5
0
0

755
 Cavity
Retainer Sets Width 600
O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
A type
600 600

A
494 494
M36 M36

B
GP2

B type

GP4 GP5
GP6
GP3

L
L

A
GP1

50 Plate S
50

50
B
Datum plane Datum plane

■ Dimension table
Nominal O：Installs guide pins at the outer positions I：Installs guide pins at the inner positions
L
dimension GP1 GP2 GP3 GP4 GP5 GP6
6060 600 245 247 494 143 145 290
6070 700 295 297 594 193 195 390

■ Combinations of A dimensions and B dimensions

A DIMM 50 60 70 80 90 100 110 120 130 150

50 50 50 50 50 50 50
60 60 60 60 60 60 60 60 60
70 70 70 70 70 70 70 70 70 70
80 80 80 80 80 80 80 80 80 80
90 90 90 90 90 90 90 90 90 90
B DIMM
100 100 100 100 100 100 100 100 100 100
110 110 110 110 110 110 110 110 110
120 120 120 120 120 120 120 120 120
130 130 130 130 130 130 130 130
150 150 150 150 150 150 150

756
TD Technical Data P.787

■ How to order

■ Order example MDB – A 6060 80 70 S O N Option

Type A B This may be changed to J or P by

Futaba if there is any addition or
change to the specification.
Nominal dimension

A DIMM install specification of guide pin

O Installs guide pins at the outer positions
B DIMM I Installs guide pins at the inner positions

■ How to order optional specification

■ Order example MDB–B 6070 100 80 S O N / #FK

Code Description Code Description

#FA Removes the threaded holes for eye bolts for Plate A Additional Specifications other than the above are also available.
Refer to the separate volume“Additional Mold Base
processing Processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Cavity Retainer Sets

Width

6
0
0

757
 Cavity
Retainer Sets Material Change Option Option

A type B type
Plate A Plate A

Plate S
Plate B
Plate B

■ How to order material change specification

■ Order example MDB – A 2530 40 50 S O N / F – AB

Material changing plate code

A Cavity plate (fixed half)
S Stripper plate
B Cavity plate (moving half)
Order code of cavity retainer set
Following the － symbol, specify the
When ordering a cavity retainer set, material changing plate. The plate of
specify with codes shown in each which material can be changed are the
page. above three types, Plate A, S and B.

Material designation code

◆How to order F HPM1
In addition to the order codes of the cavity retainer set, K NAK55
please specify“Material designation code”and“Material R NAK80
changing plate code” . A AAS（aluminum alloy A7075 or equivalent）

758
TD Technical Data P.787

Material Nominal dimension Plate S

Material name Plate A thickness Plate B thickness
designation code of cavity retainer set thickness
1515
1518
1520
1523
15 20 30 40
1818 20 25 30 35 40 20 25 30 35 40
1820
1823
1825
HPM1 2020
F NAK55
K 2023
NAK80 20 30 40
R 2025 25 30 35 40 25 30 35 40
2030
2323
2325
20 30 40 50
2327 25 30 35 40 50 25 30 35 40 50
2330
2525
2527 25 30 40 50
30 35 40 50 30 35 40 50
2530
1515
1518
1520
20 25 30 35 40 50 60 20 25 30 35 40 50 60 15
1818
1820
1825
2020 20 25 30 35 40 50 60 70 80 20 25 30 35 40 50 60 70 80
2025

AAS∗ 2030
20
（aluminum 2323
A alloy A7075 or
25 30 35 40 50 60 70 80 25 30 35 40 50 60 70 80
2325
equivalent） 2330

Cavity Retainer Sets

2525
2530 25
30 35 40 50 60 70 80 30 35 40 50 60 70 80
2535
3030 30 35 40 50 60 70 80 90 100 30 35 40 50 60 70 80 90 100
3035 30
35 40 50 60 70 80 90 100 35 40 50 60 70 80 90 100
3040
3540
40 50 60 70 80 90 100 40 50 60 70 80 90 100 35
Material Change Option

4040
＊ When using AAS, specify the AAS for all of Plate A, Plate S and Plate B. If Plate S is not used, specify AAS for Plate A and Plate B. As the thermal expansion
coefficients of aluminum alloy and steel are completely different, these two materials cannot be combined.
※Product of materials and sizes not listed above will also be made to order. Please consult our sales office.

759
760
 CAVITY RETAINER SETS FOR DIE CAST
Cavity Retainer Sets For Die Cast
■Features ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.762

■Specification and Selection ・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.763

■Cavity Retainer Sets for Die Cast

  Width 150 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.764

  Width 200 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.766
  Width 220 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.768
  Width 250 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.770
  Width 300 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.772
  Width 320 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.774
  Width 350 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.776
  Width 380 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.778
  Width 400 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.780
  Width 420 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.782
  Width 500 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.784
 Cavity Retainer
Sets for Die Cast Features
● Carefully selected materials used
● Consistent quality
● A broad range of sizes
● Low priced & short delivery time

5
1

❶ This guide, which is installed with a different pitch, prevents improper installation.
❷ Squareness datum planes are clearly marked with . As the planes are simultaneously machined, there is no datum plane
deviation.
❸ A relief is provided to prevent troubles even when any casting debris enters.
❹ Taking into account the casting port, the threaded holes for eye bolts are machined on one side.
❺ Clamp slots are provided on two side surfaces.
❻ For mold plates, F-S55C is used.
762
 Cavity Retainer
Sets for Die Cast Specification & Selection
■ Small type (for hot chamber) ■ Middle type (for hot chamber & cold chamber)

Guide pin Guide bushing Guide pin Guide bushing

Cavity Plate Cavity Plate Cavity Plate Cavity Plate

(fixed half) (moving half) (fixed half) (moving half)

This type is designed for die casting machines from This type is designed for die casting machines from 25 tons to 350
7 tons to 20 tons. The mold is mounted by directly tons. The mold is mounted by fastening with a clamping tool, etc.
fastening with bolts from the fixed side mold plate.

■ Length of guide pin ■ Specification of clamp slots

Features, Specification & Selection For Die Cast

R

A B T
Cavity Retainer Sets

The length of guide pins is set according to the The positions of clamp slots (T dimension) are available in four types.
thickness of the plate as shown below. Please select one of them.

B dimension Length of guide pin (L)

60 or less L=A＋B−3

L=A＋R
70 or more
（R≒0.6×B）

763
 Cavity Retainer
Sets for Die Cast Width 150

GP3 GPL

16
M12
150
114

33

GP1 31
GP2 4
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3
1518 180 70 72 144
1520 200 80 82 164
1523 230 95 97 194

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

40 77 40 87 40 97
40 50 87 50 50 97 60 50 107
60 97 60 107 60 117

764
TD Technical Data P.787

■ How to order

■ Order example MDE – A 1518 40 50 SN Option

Nominal dimension

A DIMM 40 50 60
This may be changed to J or P by
Futaba if there is any addition or
B DIMM 40 50 60 change to the specification.

■ How to order optional specification

■ Order example MDE–A 1520 50 60 S N / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
1
5
0
For Die Cast
Cavity Retainer Sets

765
 Cavity Retainer
Sets for Die Cast Width 200

GP3 GPL

20
M12
200
154

40

38
GP1 GP2 4
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3
2023 230 90 92 184
2025 250 100 102 204

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL
50 97 50 107 50 117 50 127
60 107 60 117 60 127 60 137
50 60 70 80
70 92 70 102 70 112 70 122
80 97 80 107 80 117 80 127

766
TD Technical Data P.787

■ How to order

■ Order example MDE – A 2025 60 50 SN Option

Nominal dimension

A DIMM 50 60 70 80
This may be changed to J or P by
Futaba if there is any addition or
B DIMM 50 60 70 80 change to the specification.

■ How to order optional specification

■ Order example MDE–A 2023 50 60 S N / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
2
0
0
For Die Cast
Cavity Retainer Sets

767
 Cavity Retainer
Sets for Die Cast Width 220

GP3 GPL

20
M12
220
174

40

38
GP1 GP2 4
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3
2225 250 100 102 204
2227 270 110 112 224
2230 300 125 127 254

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL
50 97 50 107 50 117 50 127
60 107 60 117 60 127 60 137
50 60 70 80
70 92 70 102 70 112 70 122
80 97 80 107 80 117 80 127

768
TD Technical Data P.787

■ How to order

■ Order example MDE – A 2225 60 50 SN Option

Nominal dimension

A DIMM 50 60 70 80
This may be changed to J or P by
Futaba if there is any addition or
B DIMM 50 60 70 80 change to the specification.

■ How to order optional specification

■ Order example MDE–A 2227 50 60 S N / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
2
2
0
For Die Cast
Cavity Retainer Sets

769
 Cavity Retainer
Sets for Die Cast Width 250
GPL
GP3 4

25
M16
250
182

54

52

20
GP1 GP2 T 20
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
2527 270 99 101 202
2530 300 114 116 232 15 20 25 30
2535 350 139 141 282

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

60 117 60 137 60 157
70 102 70 122 70 142
60 80 107 80 80 127 100 80 147
90 112 90 132 90 152
100 122 100 142 100 167
60 127 60 147
70 112 70 132
70 80 117 90 80 137
90 122 90 142
100 132 100 152

770
TD Technical Data P.787

■ How to order

■ Order example MDE – A 2527 80 90 SN: 20 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 60 70 80 90 100 change to the specification.

B DIMM 60 70 80 90 100

■ How to order optional specification

■ Order example MDE–A 2530 70 80 S N : 20 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
2
5
0
For Die Cast
Cavity Retainer Sets

771
 Cavity Retainer
Sets for Die Cast Width 300
GPL
GP3 4

30
M16
300
228

59

57

20
GP1 GP2 T 20
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
3032 320 122 124 248
3035 350 137 139 278 15 20 25 30
3040 400 162 164 328

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

70 112 70 137 70 152
80 117 80 137 80 157
90 122 90 142 90 162
70 90 110
100 132 100 152 100 172
110 137 110 157 110 177
120 142 120 162 120 182
70 122 70 142 70 162
80 127 80 147 80 167
90 137 90 152 90 177
80 100 120
100 142 100 162 100 177
110 147 110 167 110 187
120 152 120 172 120 197

772
TD Technical Data P.787

■ How to order

■ Order example MDE – A 3032 120 100 SN: 20 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 70 80 90 100 110 120 change to the specification.

B DIMM 70 80 90 100 110 120

■ How to order optional specification

■ Order example MDE–A 3035 70 80 S N : 20 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
3
0
0
For Die Cast
Cavity Retainer Sets

773
 Cavity Retainer
Sets for Die Cast Width 320
GPL
GP3 4

30
M20
320
248

59

57

20
GP1 GP2 T 20
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
3235 350 137 139 278
3240 400 162 164 328 15 20 25 30
3245 450 187 189 378

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

70 112 70 137 70 152
80 117 80 137 80 157
90 122 90 142 90 162
70 90 110
100 132 100 152 100 172
110 137 110 157 110 177
120 142 120 162 120 182
70 122 70 142 70 162
80 127 80 147 80 167
90 137 90 152 90 177
80 100 120
100 142 100 162 100 177
110 147 110 167 110 187
120 152 120 172 120 197

774
TD Technical Data P.787

■ How to order

■ Order example MDE – A 3240 120 100 SN: 20 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 70 80 90 100 110 120 change to the specification.

B DIMM 70 80 90 100 110 120

■ How to order optional specification

■ Order example MDE–A 3235 70 80 S N : 20 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
3
2
0
For Die Cast
Cavity Retainer Sets

775
 Cavity Retainer
Sets for Die Cast Width 350
GPL
GP3 4

30
M20
350
278

59

57

20
GP1 GP2 T 20
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
3540 400 162 164 328
15 20 25 30
3545 450 187 189 378

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

80 127 80 147 80 167
90 137 90 152 90 177
100 142 100 162 100 177
80 100 120
110 147 110 167 110 187
120 152 120 172 120 197
130 157 130 177 130 197
80 137 80 157 80 177
90 142 90 162 90 187
100 152 100 172 100 187
90 110 130
110 157 110 177 110 197
120 162 120 182 120 207
130 167 130 187 130 207

776
TD Technical Data P.787

■ How to order

■ Order example MDE – A 3540 120 100 SN: 20 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 80 90 100 110 120 130 change to the specification.

B DIMM 80 90 100 110 120 130

■ How to order optional specification

■ Order example MDE–A 3540 80 90 S N : 20 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
3
5
0
For Die Cast
Cavity Retainer Sets

777
 Cavity Retainer
Sets for Die Cast Width 380
GPL
GP3 4

30
M24
380
308

59

57

20
GP1 GP2 T 20
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
3840 400 162 164 328
3845 450 187 189 378
15 20 25 30
3850 500 212 214 428
3855 550 237 239 478

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

90 142 90 162 90 187
100 152 100 172 100 187
110 157 110 177 110 197
90 110 130
120 162 120 182 120 207
130 167 130 187 130 207
140 172 140 192 140 217
90 152 90 177 90 197
100 162 100 177 100 197
110 167 110 187 110 207
100 120 140
120 172 120 197 120 217
130 177 130 197 130 227
140 182 140 202 140 227

778
TD Technical Data P.787

■ How to order

■ Order example MDE – A 3840 120 100 SN: 20 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 90 100 110 120 130 140 change to the specification.

B DIMM 90 100 110 120 130 140

■ How to order optional specification

■ Order example MDE–A 3845 100 90 S N : 20 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
3
8
0
For Die Cast
Cavity Retainer Sets

779
 Cavity Retainer
Sets for Die Cast Width 400
GPL
GP3 4

35
M24
400
312

70

68

25
GP1 GP2 T 25
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
4045 450 179 181 362
4050 500 204 206 412 15 20 25 30
4055 550 229 231 462

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

100 162 100 187 100 207
110 167 110 187 110 207
120 172 120 192 120 217
100 120 140
130 177 130 197 130 217
140 182 140 207 140 227
150 192 150 217 150 237
100 172 100 197 100 217
110 177 110 197 110 217
120 182 120 207 120 227
110 130 150
130 187 130 207 130 227
140 192 140 217 140 237
150 207 150 227 150 247

780
TD Technical Data P.787

■ How to order

■ Order example MDE – A 4045 120 100 SN: 25 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 100 110 120 130 140 150 change to the specification.

B DIMM 100 110 120 130 140 150

■ How to order optional specification

■ Order example MDE–A 4050 100 130 S N : 25 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
4
0
0
For Die Cast
Cavity Retainer Sets

781
 Cavity Retainer
Sets for Die Cast Width 420
GPL
GP3 4

35
M30
420
332

70

68

25
GP1 GP2 T 25
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
4245 450 179 181 362
4250 500 204 206 412 15 20 25 30
4255 550 229 231 462

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

100 162 100 187 100 207
110 167 110 187 110 207
120 172 120 192 120 217
100 120 140
130 177 130 197 130 217
140 182 140 207 140 227
150 192 150 217 150 237
100 172 100 197 100 217
110 177 110 197 110 217
120 182 120 207 120 227
110 130 150
130 187 130 207 130 227
140 192 140 217 140 237
150 207 150 227 150 247

782
TD Technical Data P.787

■ How to order

■ Order example MDE – A 4245 120 100 SN: 25 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 100 110 120 130 140 150 change to the specification.

B DIMM 100 110 120 130 140 150

■ How to order optional specification

■ Order example MDE–A 4250 100 130 S N : 25 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
4
2
0
For Die Cast
Cavity Retainer Sets

783
 Cavity Retainer
Sets for Die Cast Width 500
GPL
GP3 4

40
M30
500
408

76

74

25
GP1 GP2 T 25
Datum plane L A B

■ Dimension table
Nominal dimension L GP1 GP2 GP3 T
5055 550 227 229 458
5060 600 252 254 508 15 20 25 30
5065 650 277 279 558

■ Combinations of A dimensions and B dimensions

A DIMM B DIMM GPL A DIMM B DIMM GPL A DIMM B DIMM GPL

110 177 110 197 110 217
120 187 120 207 120 227
130 187 130 207 130 227
110 130 150
140 197 140 217 140 237
150 207 150 227 150 247
160 207 160 227 160 247
110 187 110 207 110 227
120 197 120 217 120 237
130 197 130 217 130 237
120 140 160
140 207 140 227 140 247
150 217 150 237 150 257
160 217 160 237 160 257

784
TD Technical Data P.787

■ How to order

■ Order example MDE – A 5055 120 150 SN: 25 Option

Nominal dimension T DIMM 15 20 25 30

This may be changed to J or P by

Futaba if there is any addition or
A DIMM 110 120 130 140 150 160 change to the specification.

B DIMM 110 120 130 140 150 160

■ How to order optional specification

■ Order example MDE–A 5060 150 130 S N : 25 / #FK

Code Description Code Description
Specifications other than the above are also available.
#FA Removes the threaded holes for eye bolts for Plate A Additional
Refer to the separate volume“Additional Mold Base Processing
processing & Mold Parts Edition”for details.
#FB Removes the threaded holes for eye bolts for Plate B

#FK Removes the threaded holes for eye bolts for Plate A and B

Width
5
0
0
For Die Cast
Cavity Retainer Sets

785
786
 TECHNICAL DATA
Product data/Technical data
■Plate Precision of Mold Base ・・・・・・・・・・・・・・・・・・・・・・・・・・ P.788

■Dimension of Holes for Parts Installed in Mold Bases ・・・・・・・ P.789

■Threaded Holes for Eye Bolts on Mold Bases ・・・・・・・・・・・・・・ P.790

■Length of Guide Pins for Mold Bases ・・・・・・・・・・・・・・・・・・・・ P.791

■Hexagon Socket Head Cap Screw ・・・・・・・・・・・・・・・・・・・・・・ P.792

■Calculation of Gravity Center of a Mold Base ・・・・・・・・・・・・・・ P.793

■Calculation of the Deflection of the Cavity Plate (Moving Half) ・・・ P.794

■Calculation of the Deflection of Support Pins ・・・・・・・・・・・・・・ P.795

■Simplified Calculation of the Weight of Mold Bases ・・・・・・・・・ P.796

■Clamping Force & Tie Bar Spacing ・・・・・・・・・・・・・・・・・・・・・ P.797

■Material Property F-S50C/F-S55C ・・・・・・・・・・・・・・・・・・・・ P.798
■Material Property HPM1 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.799

■Material Property NAK55/NAK80 ・・・・・・・・・・・・・・・・・・・・・ P.800

■Material Property AAS/Aluminum Alloy ・・・・・・・・・・・・・・・・・ P.802

■Plastic Mold Steel Brand Comparison Table ・・・・・・・・・・・・・・・ P.804

■Material Property Data List ・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.806

■Limit Deviations for Fits Used Frequently (Holes) ・・・・・・・・・・・ P.808

■Limit Deviations for Fits Used Frequently (Shafts) ・・・・・・・・・・ P.810

■Hardness Conversion Table ・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.812

■SI Unit Conversion Table / Weight and Measure Conversion Table ・・・ P.813
 Precision of Mold Base Plates
The precision specification of standard mold bases is defined as follows:

Cavity plates, ejector plates and other plates

W F-S50C (thickness 25 or less)
Material
6.3 F-S55C (thickness 30 or more)

L dimension Limit deviations of T

300 or less ＋0.1 ∼＋0.2
Limit deviation of T
Over 300 and 600 or less ＋0.15 ∼＋0.25
Over 600 and 1150 or less ＋0.2 ∼＋0.3
6.3

1.6
L

Uniformity of
0.008 per 100 mm
thickness (T)

L dimension Over 300 and

300 or less
T dimension 1150 or less
1.6 Datum plane 5 or more and 10 or less 0.020 0.040
G Flatness of both
Over 10 and 20 or less 0.015 0.020
3.2 surfaces of T
Over 20 and 40 or less 0.010 0.015
Over 40 and 350 or less 0.008 0.010
T

※ Values per 100 mm

G
3.2 Squareness of datum
0.008 per 100 mm
plane
※The surface roughness symbols shown in the above chart
are arithmetic average roughness (Ra).

Spacer blocks

6.3
6.3

6.3

6.3
G
3.2

Material F-SS400 or equivalent or higher

＋0.15
T ＋0.05

Uniformity of thickness (T) 0.008 or 100 mm

G Variation of T in a pair of plates 0.02

3.2

※The surface roughness symbols shown in the above

charts are arithmetic average roughness (Ra).

788
Dimension of Holes for Parts Installed in Mold Bases
The dimensions of holes for guide pins, support pins and other parts installed in the standard mold bases are as follows:

V
I X

J
E

Y
H
W

F
M G
D V
S A
P
U

B
C

T N

M
R

K L X

A type of pin supplied A type of pin supplied

with a support pin collar without a support pin collar

Hole dimension of guide pins, guide bushings and support pins

Nominal Guide pin hole Guide bushing hole Support pin hole

Precision of Mold Base Plates

Dimensions of Holes for Parts Installed in Mold Bases
dimension A B C D E F G H I J K L
12 12 18 5 18 23 5 M4 12 18 6 18 14
16 16 21 25 31 6 M5 16 21 8 22 18
6
20 20 26 30 36 M6 20 26 10 28 24
8
25 25 31 35 41 25 31 12 33 29
30 30 36 8 42 48 30 36 14 40 34
M8
35 35 41 48 55 10 35 41 16 45 39
40 40 46 10 55 62 40 46 18 50 45
50 50 57 12 70 77 12 − − − − −
60 60 67 80 87 M10 − − − − −
15 15
70 70 77 90 97 − − − − −

Hole dimensions of return pins Hole dimensions of hexagon Hole dimensions of puller bolts
Nominal Return pin hole socket head cap screws Nominal Puller bolt hole
dimension M N O P＊2 ＊3 R Hexagon socket head cap dimension V W X Y＊1
Nominal screw hole
10 10 11 16 35 dimension 20 21 13 31 25
12 12 13 18 50 S T U 25 26 17 36 29
15 15 16 21 60 M8 M8 9 21 ＊1.These are dimension of H series.
20 20 21 26 80 4 M10 M10 11 24
25 25 26 31 100 M12 M12 14 28
30 30 31 36 120 M14 M14 16 31
Technical data
Product data/

35 35 36 41 130 M16 M16 18 34

＊2. The P dimensions in the above table are minimum M20 M20 22 46
values. The P dimensions can be larger than these M24 M24 26 56
values.
＊3. When plate thickness ≦P, P= plate thickness.

789
 Threaded Holes for Eye Bolts on Mold Bases
On the standard mold bases, threaded holes for eye bolts are provided for securing safety and convenience of persons transporting and handling them.
The plates on which to create the threaded holes for eye bolts are determined based on the size of the mold base as shown below. The thread size is
determined based on the maximum weight of the mold base.
Adding threaded holes for eye bolts P.226 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

Plates on which to create threaded holes

Plate T
Plate A
Plate A Plate S
Plate B
Plate B Plate B Plate U
Plate C
Plate E
Plate F
Plate L

Name of the plate on Name of the plate on Name of the plate on

Applicable mold Applicable mold Applicable mold
which threaded holes for which threaded holes for which threaded holes for
base base base
eye bolts are provided eye bolts are provided eye bolts are provided
Nominal dimension Nominal dimension Nominal dimension
Plate B Plate A and Plate B All plates
1515 to 3560 4040 to 5070 5555 to 7080

Specification of threaded holes for eye bolts

W T/2

K
F

Detailed view of P section

L

P M F K
M12 24 33
M16 29 39
M20 33 46
M24 41 56
M30 49 67
M36 59 82
M42 70 95
M48 75 103

790
Length of Guide Pins for Mold Bases
Length of guide pins
When setting the length of guide pins for a standard mold base, N dimension is determined by the thickness of the plate in which to install guide
bushings, and the length of the guide pin is determined based on the N dimension. Depending on the thickness of plates, N dimension is provided as a
range, so guide pins with a length within the range is installed in the mold base.
How to specify length of guide pins P.48 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”

N
A
A

L
L
φD φD
B

B
Mold base with stripper plate Mold base without stripper plate

N dimensions
A
D
20∼50 60 70 80 90 100 110 120 130 140 150
12 3 3∼8
16 3 3 3∼8 3∼8
20 3 3 3 3∼8 3∼13 3∼13
25 3 3 3 3∼8 3∼13 3∼13 3∼13 3∼18
30 3 3 3 3∼8 3∼13 3∼13 3∼13 3∼18 3∼18
35 3 3 3 3 3 3∼13 3∼13 3∼18 3∼18 3∼18 3∼23
40 3 3 3 3 3 3∼13 3∼13 3∼18 3∼18 3∼18 3∼23

A
D

Threaded Holes for Eye Bolts on Mold Bases

Length of Guide Pins for Mold Bases
50∼130 150 160 180 200 220 250
50 3 3∼23 3∼23 3∼33 3∼43 3∼53 3∼63
60 3 3∼23 3∼23 3∼33 3∼43 3∼53 3∼63

How to differentiate the use of guide bushing M-GBA and M-GBB

If the plate in which to install guide bushing is thin, use M-GBA and if it is thick, use M-GBB. For details on the classification of length of guide bushings
and thickness of plates, see page 31 in the separate volume“Additional Mold Base Processing & Mold Parts Edition”.

M-GBA M-GBB
Technical data
Product data/

791
 Hexagon Socket Head Cap Screw Excerpt from JIS B 1176 (2000)
Excerpt from JIS B 1176 (1974)

Dimensions of counterbore and bolt holes for hexagon socket head cap screw (reference)

φdk' φdk'
φdk φdk

k
k'

k"
k
φds φds
φds' d φds' d

Nominal size of thread (d) M3 M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 M30
ds 3 4 5 6 8 10 12 14 16 20 24 30
ds' 3.4 4.5 5.5 6.6 9 11 14 16 18 22 26 33
dk 5.5 7 8.5 10 13 16 18 21 24 30 36 45
dk' 6.5 8 9.5 11 14 17.5 20 23 26 32 39 48
k 3 4 5 6 8 10 12 14 16 20 24 30
k' 2.7 3.6 4.6 5.5 7.4 9.2 11 12.8 14.5 18.5 22.5 28
k" 3.3 4.4 5.4 6.5 8.6 10.8 13 15.2 17.5 21.5 25.5 32

Dimensions of hexagon socket

r
da
dk

ds

s t （b）
k L

Nominal size of thread (d) M3 M4 M5 M6 M8 M10 M12 （M14） M16 M20 M24 M30
Pitch of thread (P) 0.5 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5 3 3.5
b Reference 18 20 22 24 28 32 36 40 44 52 60 72
Max.＊1 5.50 7.00 8.50 10.00 13.00 16.00 18.00 21.00 24.00 30.00 36.00 45.00
dk Max.＊2 5.68 7.22 8.72 10.22 13.27 16.27 18.27 21.33 24.33 30.33 36.39 45.39
Min. 5.32 6.78 8.28 9.78 12.73 15.73 17.73 20.67 23.67 29.67 35.61 44.61
da Max. 3.6 4.7 5.7 6.8 9.2 11.2 13.7 15.7 17.7 22.4 26.4 33.4
Max. 3.00 4.00 5.00 6.00 8.00 10.00 12.00 14.00 16.00 20.00 24.00 30.00
ds
Min. 2.86 3.82 4.82 5.82 7.78 9.78 11.73 13.73 15.73 19.67 23.67 29.67
Max. 3.00 4.00 5.00 6.00 8.00 10.00 12.00 14.00 16.00 20.00 24.00 30.00
k
Min. 2.86 3.82 4.82 5.7 7.64 9.64 11.57 13.57 15.57 19.48 23.48 29.48
r Min. 0.1 0.2 0.2 0.25 0.4 0.4 0.6 0.6 0.6 0.8 0.8 1
Nominal size 2.5 3 4 5 6 8 10 12 14 17 19 22
＊3
Max. 2.56 3.071 4.084 5.084 6.095 8.115 10.115 12.142 14.142
s 17.23 19.275 22.275
Max.＊4 2.58 3.080 4.095 5.140 6.140 8.175 10.175 12.212 14.212
Min. 2.52 3.020 4.020 5.020 6.020 8.025 10.025 12.032 14.032 17.05 19.065 22.065
t Min. 1.3 2 2.5 3 4 5 6 7 8 10 12 15.5
※The above table shows main dimensions excerpt from JIS B1176: 2000. For details, refer to the standard.
＊1. This should be applied to the heads with no knurled pattern.
＊2. This should be applied to the heads with no knurled pattern.
＊3. This should be applied to strength class 12.9.
＊4. This should be applied to other strength classes.

792
Calculation of Gravity Center of a Mold Base
Calculating the center of gravity of a mold base is not an easy task because various parts are installed on a mold base and different alterations are made to
it. Shown below is a simple formula for calculating center of gravity of a mold base with plates assembled.

TW
KW
CW EFW CW
Plate T

Bt St At Rt Tt
Plate R

Mc
Plate A
KL (clamping plate: TL)

Plate S
Plate B

Plate U

Ut
Plate C

Et
Ct
Plate E
Plate F

Ft
Lt
Plate L
Center of gravity of
the mold base

Sum of the moment of each plate

Mc ＝
  Weight of mold base  
（Tm＋Rm＋Am＋Sm＋Bm＋Um＋Cm＋Em＋Fm＋Lm）
＝
（Tw＋Rw＋Aw＋Sw＋Bw＋Uw＋Cw＋Ew＋Fw＋Lw）

Hexagon Socket Head Cap Screw

Calculation of Gravity Center of a Mold Base
Mc: Center of gravity position from the top surface of Plate T
Tm∼Lm: moment of each plate with the top surface of clamping plate as a reference (omit if there is no plate)
Tw∼Lw: weight of each plate (omit if there is no plate)
※Protrusion amount of the clamping plate is assumed to be even.
※The width of the right and left side spacer blocks is assumed to be the same.

Plate code Calculation of weight of each plate Calculation of moment of each plate
Plate T Tw＝TW×TL×Tt×specific weight Tm＝Tw×Tt／2
Plate R Rw＝KW×KL×Rt×specific weight （Tt＋Rt／2）
Rm＝Rw×
Plate A Aw＝KW×KL×At×specific weight （Tt＋Rt＋At／2）
Am＝Aw×
Plate S Sw＝KW×KL×St×specific weight （Tt＋Rt＋At＋St／2）
Sm＝Sw×
Plate B Bw＝KW×KL×Bt×specific weight （Tt＋Rt＋At＋St＋Bt／2）
Bm＝Bw×
Plate U Uw＝KW×KL×Ut×specific weight （Tt＋Rt＋At＋St＋Bt＋Ut／2）
Um＝Uw×
Plate C Cw＝CW×KL×Ct×2×specific weight （Tt＋Rt＋At＋St＋Bt＋Ut＋Ct／2）
Cm＝Cw×
Plate E Ew＝EFW×KL×Et×specific weight ｛Tt＋Rt＋At＋St＋Bt＋Ut＋Ct−Ft−
Em＝Ew× （4＊1）
−Et／2｝
Plate F Fw＝EFW×KL×Ft×specific weight （Tt＋Rt＋At＋St＋Bt＋Ut＋Ct−Ft／2）
Fm＝Fw×
Plate L Lw＝TW×TL×Lt×specific weight （Tt＋Rt＋At＋St＋Bt＋Ut＋Ct＋Lt／2）
Lm＝Lw×
＊1. Applied if the specification of the ejector plates is spacer type. No need if it is counterbore type.
Technical data
Product data/

Reference: Yuichi Fukushima,“Comprehensible Plastic Injection Molding Design”Nikkan Kogyo Shinbunsya

793
 Calculation of the Deflection of the Cavity Plate (Moving Half)
The injection pressure applied by the injection molding machine acts on the projection surface inside the cavity and causes a deflection of the cavity
plate (moving half). If the deflection is large, it may result in a change in thickness of molded products, flash on them or other problems. Therefore, it
is necessary to check possible deflection by using a formula for cantilever. As shown in the formula below, the deflection increases in proportion to the
cube of thickness of backing plate (h) and to the forth power of the spacing on the inside of the spacer block. Thus, it is more effective in decreasing the
deflection to narrow the spacing on the inside of the spacer block. Increasing the thickness of the backing plate or width of the spacer block has a limit
due to the restrictions on the height of the mold and effective space of the ejector plate. Reinforcement with support pillars, etc. is also another option
that can be used to reduce deflection.

B: Width of mold plate (mm)

L: Spacing (mm) on the inside of the spacer block
W h: Thickness of backing plate (mm)
W: Length (mm) of the part receiving the cavity internal
injection pressure P
b : Width (mm) of the part receiving the cavity internal
Cavity
projection injection pressure P
area p : Cavity internal injection pressure（kgf/cm2）
B
b

E : modules of longitudinal elasticity (Young’

s modules) of the
material（kgf/cm2）
δmax : maximum deflection of the backing plate (mm)

[ When assuming W＝L for simplifying the calculation ]

p Cavity 5･p･b･L4
δmax＝
32･E･B･h3
Cavity plate (moving half)
3 5･p･b･L4
Backing plate h＝
h

32･E･B･δmax
Spacer block
δmax

Bottom clamping plate

L

E values A rough guide of cavity internal injection pressure

Material E（kgf/cm2） P (reference value)
Soft steel 210×104 Molding condition p（kgf/cm2）
Prehardened steel Lower injection pressure 200∼400
203×104
(SCM440 series) Higher injection pressure 400∼600
Cast iron （75∼105）
×10 4
(Note) In practice, it is desirable to measure the actual values using a
Ultra duralumin pressure sensor P.816
73×104
(ALQUEEN 300)

A rough guide of maximum allowable deflection that takes parting line flash
into account (reference value)
Molding material, etc. Maximum allowable deflection δmax (mm)
Materials with high liquidity (PA, PP, etc.) 0.025 or less
Materials with regular liquidity 0.03∼0.05
Molded product that allows flash 0.1∼0.2

Reference: Michio Komatsu,“Plastic Injection Molding Design Manual”Nikkan Kogyo Shinbunsya

794
Calculation of the Deflection of Support Pins
In addition to the parting line for taking out molded products, a three-plate mold has one more parting line for taking runner out. Therefore, the three-plate
mold makes a larger mold opening stroke to take out runner, and thus the support pin that guides and supports the opening and closing of cavity plate
(fixed half) is subject to a bending moment that is a product of weight of the cavity plate (fixed half). and distance to the fully open position resulting in a
deflection. Therefore, it is necessary to check possible deflection by using a formula for cantilever.

Center of gravity
φD

Y
N M
L

W : Load applied per support pin (kgf)

s modules) 21,000kgf/mm2
E : Modules of longitudinal elasticity (Young’
I : Cross sectional secondary moment I＝π （D−1） 4
／64
※Oil groove is assumed here and (D -1) is used as diameter.

Deflection Y (mm) in L (mm)

Calculation of the Deflection of the Movable Side Mold Plate

Calculation of the Deflection of Support Pins
W・M3 3・N
Y＝ 1＋
3・E・I 2・M

As shown in the above, the deflection increases in proportion to the load applied to the support pin (W) and to the cube of mold opening distance (M).
Therefore, it significantly changes depending on the mold base used and the mold opening distance required. If the deflection becomes larger than the
clearance of the pin and bushing, they will slide with interference, making a squeak noise, which will cause binding, etc.
In practice, however, the clearance between the pin and bushing is only 0.03 mm, and keeping all the molds smaller than this value requires the use of
pins with a larger diameter, and is thus difficult from the perspective of effective space and costs.
It would be better to use such a measure when necessary for quality reason, etc.
For allowable deflection, 0.3 to 0.4 mm or less values are used in many applications, but the values are generally determined on a case by case basis as
they change according to the level of precision required for the molded products, appearance and mold. Calculating deflection is suggested to evaluate the
precision of the molds that have been produced in the past to evaluate their level of precision, including potential of binding and other troubles in planning
a new design, or establish and maintain an internal design standard.
Technical data
Product data/

Reference: Kazunobu Uchida,“Mold Technology”April, 1987, Nikkan Kogyo Shinbunsya

795
 Simplified Calculation of the Weight of Mold Bases
Use this formula when calculating approximate weight of the standard mold bases.
The weight coefficient differs depending on the sizes and series of the mold bases. Please select an appropriate
weight coefficient from the table below:

W ＝ a×H ※1. The calculated result is the

weight of the mold bases for
clamping type clamping plate.
W : weight (kg) 2. The calculated weight has an
H

a : Weight coefficient error of 5% at maximum.

H : Height of the mold base (mm)

Weight coefficient table

Nominal Weight coefficient (a) Nominal Weight coefficient (a) Nominal Weight coefficient (a)
dimension 2-plate type 3-plate type dimension 2-plate type 3-plate type dimension 2-plate type 3-plate type
1113 0.12 0.12 2330 0.51 0.51 3060 1.34 1.36
1313 0.13 0.13 2335 0.59 0.60 3335 0.87 0.88
1315 0.15 0.15 2340 0.68 0.68 3340 0.99 1.00
1515 0.17 0.17 2525 0.46 0.47 3345 1.11 1.13
1518 0.20 0.20 2527 0.50 0.51 3350 1.24 1.25
1520 0.23 0.23 2530 0.56 0.56 3535 0.91 0.92
1523 0.26 0.26 2535 0.65 0.66 3540 1.04 1.05
1525 0.28 0.28 2540 0.74 0.75 3545 1.17 1.18
1530 0.34 0.34 2545 0.83 0.84 3550 1.30 1.32
1818 0.24 0.24 2550 0.93 0.94 3555 1.43 1.45
1820 0.27 0.27 2730 0.59 0.60 3560 1.56 1.58
1823 0.31 0.31 2735 0.69 0.70 4040 1.16 1.18
1825 0.33 0.34 2740 0.79 0.80 4045 1.31 1.33
1830 0.40 0.41 2750 0.99 1.00 4050 1.46 1.47
1835 0.47 0.48 2930 0.65 0.66 4055 1.60 1.62
2020 0.30 0.30 2935 0.76 0.77 4060 1.75 1.77
2023 0.35 0.35 2940 0.87 0.88 4070 2.04 2.06
2025 0.38 0.38 3030 0.67 0.68 4545 1.50 1.53
2030 0.45 0.46 3032 0.71 0.72 4550 1.67 1.70
2035 0.53 0.53 3035 0.78 0.79 4555 1.84 1.87
2040 0.61 0.61 3040 0.90 0.91 4560 2.00 2.04
2045 0.68 0.69 3045 1.01 1.02 5050 1.85 1.88
2323 0.39 0.39 3050 1.12 1.13 5060 2.22 2.26
2325 0.42 0.43 3055 1.23 1.25 5070 2.59 2.64
2327 0.46 0.46

※ These coefficients do not apply to the high rigidity type mold bases.

796
Clamping Force & Tie Bar Spacing [Reference Values]

Clamping plate dimension

Mold plate dimension (A) Tie bar

Mold base
Tiber spacing

Tiber spacing (H)

Simplified Calculation of the Weight of Mold Bases

Clamping Force & Tie Bar Spacing [Reference Values]
Futaba mold bases
Clamping force Standard tie bar spacing＊1
Dimension of applicable Clamping plate dimension (mm)
(tonf) （V）
(H)× （mm）
mold plate (A)＊2（mm） Clamping type Bolt fastening type
15 225×225 150 200 230
25 260×260 200 250 280
30 260×260 200 250 280
50 310×310 250 300 350
75 360×360 300 350 400
100 410×410 350 400 550
150 510×510 450 500 550
180 510×510 450 500 550
220 560×560 450 500 550
250 610×610 550 600 700
280 610×610∼660×660 550 600 700
350 710×710∼750×750 600 700
450 810×810∼855×855 700 800 890
550 860×860∼900×900 700 800 890
650 950×950 800 890
850 1060×1060 850 950
＊1. Please note that the above dimensions are a rough guide only. For accurate dimensions, see the catalog of your injection molding machine.
Technical data
Product data/

＊2. The dimensions of mold bases (A) are defined by reference to those for clamping type clamping plate.

797
 Material Property F-S50C/F-S55C (JIS S50C & S55C)
Features
●Carbon steels that have the highest strength among the carbon steels (carbon steels for mechanical structure)
●To minimize the difference in property values due to the difference in thickness, we use JIS S50C or equivalent for the plates with a thickness
of 25 mm or less, and JIS S55C for the plates with a thickness of 30mm or more.

Properties
Hardness  170 ∼ 240HB

Mechanical strength
0.2% proof stress Tensile strength Charpy impact value
Elongation Reduction in area
Temperature N/mm2 N/mm2 J/cm2
％ ％
{kgf/mm2} {kgf/mm2} {kgf･m/cm2}
366 749
20°
C 17.1 31.2
｛37.3｝ ｛76.4｝
40
348 724 ｛4.1｝
50°
C 18.4 38.2
｛35.5｝ ｛73.8｝
Test temperature 0°
C
303 732
300°
C 19.5 37.1
｛30.9｝ ｛74.6｝

Thermal expansion coefficient Thermal conductivity

Temperature 25∼100°
C 25∼200°
C 25∼300°
C Temperature 50°
C 300°
C
Thermal expansion Thermal conductivity
46.0 46.5
coefficient 11.6 12.6 13.3 W/（m･° C）
｛0.110｝ ｛0.111｝
×10-6/° C {cal/（cm･s･°C）}

Welding conditions
Welding method TIG welding
Electrode φ2.4 thorium tungsten electrode
Welding electrode TGS 50 (Kobe Steel, Ltd. JIS YGT50 or equivalent)
Welding current 80∼140A
Shielding gas Argon 10∼13R/min
Preheat
200°
C or higher
temperature
Postheat
500°
C
temperature

798
Material Property HPM1 (40HRC Class Prehardened Steel)
Features
●A prehardened steel with a hardness of 40 HRC class
●As free-cutting elements are added, it provides excellent machinability.
●A good surface texture is achieved.
 As free-cutting elements are added, do not carry out precision texturing.

Properties
Hardness  37 ∼ 41HRC

Mechanical strength
0.2％ proof stress Tensile strength Charpy impact value
Elongation Reduction in area
Sampling direction N/mm2 N/mm2 J/cm2
(%) (%)
{kgf/mm2} {kgf/mm2} {kgf･m/cm2}
1,029 1,225 15
L 18 40
｛105｝ ｛125｝ ｛1.5｝
1,010 1,216 10
T 10 25
｛103｝ ｛124｝ ｛1.0｝
Test pieces for tensile test: JIS # 10  Test piece for impact test: 10R notch  Impact test temperature：23°
C

Modules of longitudinal elasticity (Young’

s modules) Density Specific heat
Temperature 20°
C Temperature 20°
C Temperature 20°
C 400°
C
Modules of longitudinal elasticity 206,000 3 Specific heat
Density g/cm 7.75 510 654
s modules) N/mm2 {kgf/mm2}
(Young’ ｛21,000｝ J/（kg･° C）

Thermal expansion coefficient

Temperature 20∼100°
C 20∼200°
C 20∼300°
C 20∼400°
C
Thermal expansion coefficient ×10-6/°
C 11.4 11.8 12.3 12.8

Thermal conductivity
Temperature 20°
C 100°
C 200°
C 300°
C 400°
C

Material Property F-S50C/F-S55C

Material Property HPM1
Thermal conductivity W/（m･°
C） 32.7 33.1 33.5 34.7 34.7
{cal/（cm･s･°C）} ｛0.078｝ ｛0.079｝ ｛0.080｝ ｛0.083｝ ｛0.083｝

Welding conditions
Welding method TIG welding
Electrode φ2.4 or φ3.2（2％ thorium tungsten electrode）
Welding electrode HPM1-W or YAG (manufactured by Hitachi Metal)
Welding electrode Current range
φ2.4 ……………… 80∼160A
Welding current
φ3.2 ……………… 110∼200A
φ4.0 ……………… 130∼250A
Nozzle dia. Flow rate
Shielding gas Pure Argon φ10∼φ12 …… 10∼15R/min
Technical data
Product data/

φ12∼φ16 …… 12∼20R/min
Preheat temperature 100∼400°
C
Postheat temperature 200∼500°
C

799
 Material Property NAK55/NAK80 (40HRC Class Prehardened Steel)
Features
NAK55
●A prehardened steel with a hardness of 40 HRC.
●As free-cutting elements are added, it provides excellent machinability.
●As free-cutting elements are added, its polishability and surface texture property are inferior to those of NAK80.
 If polishability and surface texture property are more important for your application, please use NAK80.

NAK80
●A prehardened steel with a hardness of 40 HRC.
●Its machinability is inferior to that of NAK55.
 If machinability is more important for your application, please use NAK50.
●As this is a clean steel, superior surface texture or mirror polish is achieved.

Properties
Hardness  37 ∼ 43HRC

Mechanical strength
0.2％ proof stress Tensile strength Reduction in Charpy impact value
Sampling Elongation
Material N/mm2 N/mm2 area J/cm2
direction (%)
{kgf/mm2} {kgf/mm2} (%) {kgf･m/cm2}
981 1,255 18
L 15 40
｛100｝ ｛128｝ ｛1.8｝
NAK55
981 1,275 12
T 14 38
｛100｝ ｛130｝ ｛1.2｝
1,010 1,255 20
L 16 40
｛103｝ ｛128｝ ｛2.0｝
NAK80
981 1,255 14
T 16 40
｛100｝ ｛128｝ ｛1.4｝
Test pieces for tensile test: JIS # 4  Test piece for impact test: 2mm U notch  Impact test temperature：20°
C

Modules of longitudinal elasticity (Young’

s modules) Density Specific heat
Temperature 20°
C Temperature 20°
C Temperature 20°
C
Modules of longitudinal elasticity (Young’
s modules) 201,000 3 Specific heat
Density g/cm 7.80 481
N/mm2 {kgf/mm2} ｛20,500｝ J/（kg･° C）

Thermal expansion coefficient

Temperature 20∼100°
C 20∼200°
C 20∼300°
C
Thermal expansion coefficient ×10-6/°
C 11.3 12.5 13.4

Thermal conductivity
Temperature 20°
C 100°
C 200°
C 300°
C
Thermal conductivity 38.9 39.3 41.9 42.7
W/（m･° C）{cal/（cm･s･° C）} ｛0.093｝ ｛0.094｝ ｛0.100｝ ｛0.102｝

800
Welding conditions
Welding method TIG welding
Electrode (Tungsten electrode) φ1.6 φ2.4
Welding electrode (NAL-W manufactured by Daido Special Steel) φ1.6 φ2.4
Welding current 70∼150A 150∼250A
Shielding gas (Argon) 6∼9R/min 7∼10R/min
Preheat temperature 300∼400°
C
Postheat temperature 450∼520°
C

Please use high precision plates ideally suited for applications such as insert
①Available in various materials
Material NAK55/NAK80

②High precision milling finish type and high precision

grinding finish type can be selected according to
usage.
③High-quality finishes and squareness will significantly
increase the workability of your machining work
④High precision plates will be made to your specified
sizes and limit deviations
Technical data
Product data/

⑤For details, please refer to our general catalog “Red

Book”.

801
 Material Property AAS/Aluminum Alloy (JIS A7075 equivalent)

Features
●Excellent machinability and EDM performance (three times or more better in comparison to steel) will facilitate your machining work.
●Provides the best strength among aluminum alloys and mechanical properties equivalent to those of carbon steels
●Provides superior corrosion resistance and thermal conductivity in comparison to steels
●Low weight (approx. three times lighter in comparison to steel) enables easy handling.
●To prevent distortion due to machining, residual stresses are relieved after heat treatment.
 (T651 treatment or T652 treatment are carried out)

Properties

0.2％ proof Tensile Young’s Thermal

Thermal conductivity
Thickness stress strength Elongation Hardness modules expansion Specific
Material W/（m･° C）
mm N/mm2 N/mm2 (%) HB N/mm2 coefficient weight
{cal/（cm･s･°
C）}
{kgf/mm2} {kgf/mm2} {kgf/mm2} ×10-6/° C
500 570
AAS-T651 40 13 156
｛51｝ ｛58｝ 71,600 130
23.6 2.80
420 520 ｛7,300｝ ｛0.31｝
AAS-T652 100 9 150
｛43｝ ｛53｝
420 470 73,600 155
A2014-T651 − 5 130 23.0 2.80
｛43｝ ｛48｝ ｛7,500｝ ｛0.37｝
366 749 206,000 46.0
F-S55C − 17.1 170∼240 11.6 7.85
｛37.3｝ ｛76.4｝ ｛21,000｝ ｛0.11｝
275
451 206,000 58.6
F-SS400 − ｛28｝ 36 116∼150 12.2 7.85
｛46｝ ｛21,000｝ ｛0.14｝
Yield point

About thermal refining codes

Aluminum alloy can be cold worked, quenched, tempered or normalized to control its strength, moldability and other properties. Obtaining desired
properties through such operations is called thermal refining.
T651 ……………Solution heat treated, stress relieved by stretching and then artificially aged.
T652 ……………Solution heat treated, stress relieved by compression and then artificially aged.

802
 Product data/
Material AAS/Aluminum Alloy

803
Technical data
 Plastic Mold Steel Brand Comparison Table
Plastic Mold Steel Brands Comparison Table

Applicable standards Material manufacturer

Classification

Hardness DIN Futaba Nippon

for use standard Nihon Sanyo
Kobe Hitachi Daido Bohla Aichi steel Nachi
（HRC） JIS AISI Material product Steel Metals Steel Uddeholm Steel
Kosyuha
& sumi-
special
-Fujikoshi
Name Steel steel
No. tomo metal
As rolled

F-S55C S55C
steel

13
F-S50C S50C
SC 1055 CK55 1.1203
Series 1050 C55 1.0535 KTSM21
KPM1 SD17
13 KTSM2A AUK1 PC55
KPMAX SD18T
KTSM22
SCM
28 4140 42CrMo4 1.7225 KTSM31 PDS3 AUK11 SD61
Series
SCM HPM7
33 P20 <Supeior weldability> HPM7 PXA30 KPM30
(Improved) PXA30
PLAMAX
Pre hardened steel

SCM M238 SD70

33 P20 35CrMo4 1.2330 KTSM3M
(Improved) IMPAX HH SD100
（35∼40HRC）
SCM P20Ni HPM- HPM-
NIMAX
(Improved) Series MAGIC MAGIC
HPM1
<Free-machining> HPM1 NAK55 KAP65 PCM40
NAK55
P21
precipitation NAK80 HPM-
40 <Mirror finishing property> NAK80 KAP88 PCM40S
hardening HPM-PRO PRO
<Rust ‐ prevention
P21 CENA1 CENA1
property>
SKD61 FDAC
（H13）（X40CrMoV51）（1.2344） FDAC DH2F KAP90F
(Improved) DH2F
SKD61 DHA ORVAR-2M
50 H13 X40CrMoV51 1.2344 F-SKD61 DAC SKD61 KDA QD61
Quenched and tempered

Series DHA1 W302

SKD11 （D2） (X155CrVMo121) (1.2379) F-SKD11 SLD DC11 SKD11 KD11 QC11 CDS11
steel

SKD11 HPM31 PD613

56 ∼ 62 HPM31 CALDIE AUD11 KD21 QCM8
(Improved) PD613 DC53

SKD12 A2 RIGOR DC12 RIGOR KD12

SUS Series HPM38 STAVAX

420 (X38Cr13) (1.4031) HPM38 S-STAR 420M PROVA-400
420J2 STAVAX M303
33
Pre hardened

SUS Series
HPM77 G-STAR RoyAlloy
(free-machining)
SUS Series
Stainless steel

35 S17400 PSL NAK101 U630 QSH6

630
EDRO400
40 SUS Series
M303-HH
SUS Series HPM38 HPM38 S-STAR STAVAX
52 420 (X38Cr13) (1.4031) PROVA-400
420J2 STAVAX HPM38S D-STAR M333
M340 QPD5 440C
SUS Series
57 440C X105CrMo17 1.4125 SUS440C SUS440C ELMAX SPC5 PROVA-500
440C
(Power metall) (Power metall) (Power metall)
50
Age hardened

Maraging steel YAG MAS1C KMS18-20 EXEO-M21

or more
steel

40 Non-magunetic steel HPM75 NMS1

（ ）
MOLD-
Alloy steel

HIT71
Copper

MAX
HIT72
HH/LH/
HIT75
XL/V

Reference: Special Steel Vol.56 No.6 2007

804
Stamping Die Steel Brands Comparison Table

Applicable standards Material manufacturer

Classification

Hardness Futaba
for use equivalent equivalent DIN standard Nihon Sanyo
Hitachi Daido Bohla Nachi
（HRC） JIS AISI Material product Metals Steel Uddeholm
Kosyuha special Aichi Steel
-Fujikoshi
Name Steel steel
No.
Carbon tool

53 ∼ 61 SK105
steel

W1-10 C105W1 1.1645 YK3 QK3 SK3

SKS93 （W5） F-SK3 YCS3 YK30 K3M QK3M SK301

SKS3 （O1） 100MnCrW4 1.2510 F-SKS3 SGT GOA KS3 QKS3 SKS3
SKD1 D3 X210Cr12 1.2080 CRD DC1 KD1 QC1 SKD1
SKD11 （D2） (X155CrVMo121) (1.2379) F-SKD11 SLD DC11 K110 KD11 QC11 SKD11 CDS11
For 8% cr high temp. QCM7 AUD15
SLD8 DC53 K340 KD21 MDS9
tempering QCM8 AUD11
High
hardness Free machining &
low quenching strain & SLD-MAGIC SLD-MAGIC
coated long life
SKD 11 KD11S
Alloy tool steel

(Improved) Middle
Free- ARK1 ARK1
56 ∼ 62 machining
Cr SKD

Matrix Series DCMX CALDIE

SXACE
Others NOGA
AUD11X
Powder dies steel VANADIS4E
Nitriding power steel VANCRON40
SKD12 A2 X100CrMoV51 1.2363 RIGOR DC12 RIGOR KD12
FH5 SX105V
Flame hardening steel HMD5 GO5 QF3
KRCX SX4
Low temperature air-cooled quenching ACD37 ACD37 GO4 KSM
High impact steel YSM GS5 KTV5 QF1 AKS4
SCM HPM7
33 P20 <Supeior weldability> HPM7 PXA30 KPM30
(Improved) PXA30
SCM IMPAX HH
37 P20 35CrMo4 1.2330
(35 ∼ 40HRC)
Pre hardened steel

(Improved)
SCM
P20 <Free-machining> GO40F
(Improved)

Mold Steel Brand Comparison Table

HPM1
<Free-machining> HPM1 NAK55 KAP65 PCM40
40 NAK55
Precipitation P21
NAK80
hardening <Mirror finishing property> HPM-PRO NAK80 KAP88 PCM40S
HPM-PRO
P21 <Rust ‐ preventio property> CENA1 CENA1
SKH51 M2 S6-5-2 1.3343 YXM1 MH51 S600 H51 QH51 SKH9
High-speed tool steel

SKH55 HM35
M35 S6-2-5 1.3243 YXM4 MH55 S705 HM35
Series HS53M
55 ∼ 68 SKH57 S10-4-3-10 1.3207 XVC5 MH8 MV10
HS93R
Series DURO-SP
YXR3 DRM1 KMX1 DURO-F1,
Matrix Series High-speed YXR33 DRM2 W360 KMX2 QHZ F3, F7
YXR7 DRM3 KMX3 DURO-V2, V5
SKH40 1.3244 HAP40 DEX40 VANADIS30 FAX38
Powder metal high-
speed tool steel

M3:2 ASP23 HAP10 DEX20 VANADIS23 ASP23 FAX31

VANADIS60 ASP30
58 ∼ 70 HAP50
DEX60 Super ASP60
FAX55
HAP72 FAXG2
Technical data
Product data/

Clean SPMR8
DEX-M1
Matrix Series powder metal high-speed HAP5R
DEX-M3

Reference: Special Steel Vol.56 No.6 2007

805
 Material Property Data List
Property values shown in International system of unit (SI unit)
Hardness for use Tensile property Physical property
Thermal expansion Thermal conductivity
Classification Material 0.2％ proof stress Tensile strength coefficient coefficient
HRC HB
N/mm2 N/mm2 ×10-6/°C （m･°C）
W/
〔20∼200°C〕 〔20°C〕
275 13.1
− 58.6〔 0°C〕
Carbon tool

F-SS400 116∼150 450

（Yield point） 〔0∼300°C〕
steel

12.6
F-S55C 6∼22 170∼240 366 749 46.0〔50°C〕
〔25∼200°C〕
HPM7 29∼33 279∼311 853 973 12.2 34.3
12.7
PXA30 30∼33 286∼311 845 980 34.7
〔30∼200°C〕
12.3
HPM-MAGIC 37∼41 344∼381 1,020 1,200 31.4
〔30∼200°C〕
Prehardened steel

HPM1 37∼41 344∼381 1,010 1,216 11.8 32.7

NAK55 37∼43 344∼400 981 1,255
12.5 38.9
NAK80 37∼43 344∼400 981 1,255
13.0
HPM-PRO 37∼41 344 ∼ 381 1,020 1,200 28.3
〔30 ∼ 200°C〕
CENA1 37∼42 344∼390 1,150 1,225 11.4 28.1
DH2F 38∼42 353∼390 1,100 1,330 10.8 25.5
11.7
FDAC 38∼42 353∼390 1,060 1,240 30.5
〔20∼100°C〕
50∼55 − 1,618 1,912 11.9 25.1
HPM38
Stainless

29∼33HRC (Prehardened state) 〈52HRC〉 〈53HRC〉

50∼55 − 1,610 2,050 11.0 16.0
STAVAX ESR
27∼35HRC (Prehardened state) 〈55HRC〉 〈50HRC〉
1,070 1,250 12.5 30.5
※1 F-SKD61 53 or less −
〈40HRC〉 〈45HRC〉
1,490 2,120 12.3 28.5
HPM31 55∼60 −
〈61HRC〉 〈60HRC〉
1,815 2,280 11.7 28.5
※2 PD613 56∼61 −
〈59HRC〉 〔30∼200°C〕 〈60HRC〉
11.6 26.0
Quenched and tempered steel

RIGOR 54∼59 − − −
〈62HRC〉
− 1,670 11.3 45.2
F-SK3 58∼63 −
〈60HRC〉 〈197HB: annealed state〉
− 1,370 12.4 34.7
F-SKS3 60∼62 −
〈60HRC〉 〈62HRC〉
1,570 1,810 12.5 29.3
Cold work tool steel

F-SKD11 58∼63 −
〈60HRC〉 〈60HRC〉
1,780 1,890
SLD-MAGIC 60∼62 − 12.3 28.9
〈60HRC〉
− 1,690 12.4 29.5
ARK1 58∼62 −
〈60HRC〉 〈59HRC〉
13.1 46.0〔100°C〕
ACD37 58∼62 − − −
〈60HRC〉
11.7 23.9
ASP23 56∼65 − − −
〈62HRC〉
Aluminum AAG − 59 100 200 23.8 138
alloy AAS − 150 420 520 23.6 130
※1. Hot work tool steel ※2. Die steel for plastic mold

806
The table below lists the property values of main plates shown in the Red Book.
For details on each material, see the Red Book. Red Book is the name of our plate general catalog.

Property values shown in traditional unit systems (CGS and MKS units)
Hardness for use Tensile property Physical property
Thermal expansion Thermal conductivity
Classification Material 0.2％ proof stress Tensile strength coefficient coefficient
HRC HB
kgf/mm2 kgf/mm2 ×10-6/°C cal/（cm･s･°C）
〔20∼200°C〕 〔20°C〕
28 13.1
− 0.14〔 0°C〕
Carbon tool

F-SS400 116∼150 46
(Yield point) 〔0∼300°C〕
steel

12.6
F-S55C 6∼22 170∼240 37.3 76.4 0.110〔50°C〕
〔25∼200°C〕
HPM7 29∼33 279∼311 87.0 99.2 12.2 0.082
12.7
PXA30 30∼33 286∼311 86 100 0.083
〔30∼200°C〕
12.3
HPM-MAGIC 37∼41 344∼381 104 122 0.075
〔30∼200°C〕
Prehardened steel

HPM1 37∼41 344∼381 103 124 11.8 0.078

NAK55 37∼43 344∼400 100 128
12.5 0.093
NAK80 37∼43 344∼400 100 128
13.0
HPM-PRO 37∼41 344∼381 104 122 0.068
〔30∼200°C〕
CENA1 37∼42 344∼390 117 125 11.4 0.067
DH2F 38∼42 353∼390 112 136 10.8 0.061
11.7
FDAC 38∼42 353∼390 108 126 0.073
〔20∼100°C〕
50∼55 − 165 195 11.9 0.060
HPM38
Stainless

29∼33HRC (Prehardened state) 〈52HRC〉 〈53HRC〉

50∼55 − 164 209 11.0 0.038
STAVAX ESR
27∼35HRC (Prehardened state) 〈55HRC〉 〈50HRC〉
109 127 12.5 0.073
※1 F-SKD61 53 or less −
〈40HRC〉 〈45HRC〉
152 216 12.3 0.068
HPM31 55∼60 −
〈61HRC〉 〈60HRC〉
185 233 11.7 0.068
※2 PD613 56∼61 −
〈59HRC〉 〔30∼200°C〕 〈60HRC〉
11.6 0.062
Quenched and tempered steel

RIGOR 54∼59 − − −
〈62HRC〉
− 170 11.3 0.108
F-SK3 58∼63 −
〈60HRC〉 〈197HB: annealed state〉
− 140 12.4 0.083
F-SKS3 60∼62 −
〈60HRC〉 〈62HRC〉
160 185 12.5 0.070 Material Property Data List
Cold work tool steel

F-SKD11 58∼63 −
〈60HRC〉 〈60HRC〉
182 193
SLD-MAGIC 60∼62 − 12.3 0.069
〈60HRC〉
− 172 12.4 0.070
ARK1 58∼62 −
〈60HRC〉 〈59HRC〉
13.1 0.11〔100°C〕
ACD37 58∼62 − − −
〈60HRC〉
11.7 0.057
ASP23 56∼65 − − −
〈62HRC〉
Alluminium AAG − 59 10 20 23.8 0.33
alloy AAS − 150 43 53 23.6 0.31
※1. Hot work tool steel ※2. Die steel for plastic mold
Technical data
Product data/

807
 Limit Deviations for Fits Used Frequently (Holes)
Limit deviations for frequently used fits of holes
Classification
of basic size Tolerance class of hole
(mm)
Over Or less B10 C9 C10 D8 D9 D10 E7 E8 E9 F6 F7 F8 G6 G7 H6 H7 H8
＋180 ＋85 ＋100 ＋34 ＋45 ＋60 ＋24 ＋28 ＋39 ＋12 ＋16 ＋20 ＋8 ＋12 ＋6 ＋10 ＋14
− 3
＋140 ＋60 ＋60 ＋20 ＋20 ＋20 ＋14 ＋14 ＋14 ＋6 ＋6 ＋6 ＋2 ＋2 0 0 0
＋188 ＋100 ＋118 ＋48 ＋60 ＋78 ＋32 ＋38 ＋50 ＋18 ＋22 ＋28 ＋12 ＋16 ＋8 ＋12 ＋18
3 6
＋140 ＋70 ＋70 ＋30 ＋30 ＋30 ＋20 ＋20 ＋20 ＋10 ＋10 ＋10 ＋4 ＋4 0 0 0
＋208 ＋116 ＋138 ＋62 ＋76 ＋98 ＋40 ＋47 ＋61 ＋22 ＋28 ＋35 ＋14 ＋20 ＋9 ＋15 ＋22
6 10
＋150 ＋80 ＋80 ＋40 ＋40 ＋40 ＋25 ＋25 ＋25 ＋13 ＋13 ＋13 ＋5 ＋5 0 0 0

10 14
＋220 ＋138 ＋165 ＋77 ＋93 ＋120 ＋50 ＋59 ＋75 ＋27 ＋34 ＋43 ＋17 ＋24 ＋11 ＋18 ＋27
＋150 ＋95 ＋95 ＋50 ＋50 ＋50 ＋32 ＋32 ＋32 ＋16 ＋16 ＋16 ＋6 ＋6 0 0 0
14 18

18 24
＋244 ＋162 ＋194 ＋98 ＋117 ＋149 ＋61 ＋73 ＋92 ＋33 ＋41 ＋53 ＋20 ＋28 ＋13 ＋21 ＋33
＋160 ＋110 ＋110 ＋65 ＋65 ＋65 ＋40 ＋40 ＋40 ＋20 ＋20 ＋20 ＋7 ＋7 0 0 0
24 30

＋270 ＋182 ＋220

30 40
＋170 ＋120 ＋120 ＋119 ＋142 ＋180 ＋75 ＋89 ＋112 ＋41 ＋50 ＋64 ＋25 ＋34 ＋16 ＋25 ＋39
＋280 ＋192 ＋230 ＋80 ＋80 ＋80 ＋50 ＋50 ＋50 ＋25 ＋25 ＋25 ＋9 ＋9 0 0 0
40 50
＋180 ＋130 ＋130
＋310 ＋214 ＋260
50 65
＋190 ＋140 ＋140 ＋146 ＋174 ＋220 ＋90 ＋106 ＋134 ＋49 ＋60 ＋76 ＋29 ＋40 ＋19 ＋30 ＋46
＋320 ＋224 ＋270 ＋100 ＋100 ＋100 ＋60 ＋60 ＋160 ＋30 ＋30 ＋30 ＋10 ＋10 0 0 0
65 80
＋200 ＋150 ＋150
＋360 ＋257 ＋310
80 100
＋220 ＋170 ＋170 ＋174 ＋207 ＋260 ＋107 ＋126 ＋159 ＋58 ＋71 ＋90 ＋34 ＋47 ＋22 ＋35 ＋54
＋380 ＋267 ＋320 ＋120 ＋120 ＋120 ＋72 ＋72 ＋72 ＋36 ＋36 ＋36 ＋12 ＋12 0 0 0
100 120
＋240 ＋180 ＋180
＋420 ＋300 ＋360
120 140
＋260 ＋200 ＋200
＋440 ＋310 ＋370 ＋208 ＋245 ＋305 ＋125 ＋148 ＋185 ＋68 ＋83 ＋106 ＋39 ＋54 ＋25 ＋40 ＋63
140 160
＋280 ＋210 ＋210 ＋145 ＋145 ＋145 ＋85 ＋85 ＋85 ＋43 ＋43 ＋43 ＋14 ＋14 0 0 0
＋470 ＋330 ＋390
160 180
＋310 ＋230 ＋230
＋525 ＋355 ＋425
180 200
＋340 ＋240 ＋240
＋565 ＋375 ＋445 ＋242 ＋285 ＋355 ＋146 ＋172 ＋215 ＋79 ＋96 ＋122 ＋44 ＋61 ＋29 ＋46 ＋72
200 225
＋380 ＋260 ＋260 ＋170 ＋170 ＋170 ＋100 ＋100 ＋100 ＋50 ＋50 ＋50 ＋15 ＋15 0 0 0
＋605 ＋395 ＋465
225 250
＋420 ＋280 ＋280
＋690 ＋430 ＋510
250 280
＋480 ＋300 ＋300 ＋271 ＋320 ＋400 ＋162 ＋191 ＋240 ＋88 ＋108 ＋137 ＋49 ＋69 ＋32 ＋52 ＋81
＋750 ＋460 ＋540 ＋190 ＋190 ＋190 ＋110 ＋110 ＋110 ＋56 ＋56 ＋56 ＋17 ＋17 0 0 0
280 315
＋540 ＋330 ＋330
＋830 ＋500 ＋590
315 355
＋600 ＋360 ＋360 ＋299 ＋350 ＋440 ＋182 ＋214 ＋265 ＋98 ＋119 ＋151 ＋54 ＋75 ＋36 ＋57 ＋89
＋910 ＋540 ＋630 ＋210 ＋210 ＋210 ＋125 ＋125 ＋125 ＋62 ＋62 ＋62 ＋18 ＋18 0 0 0
355 400
＋680 ＋400 ＋400
＋1010 ＋595 ＋690
400 450
＋760 ＋440 ＋440 ＋327 ＋385 ＋480 ＋198 ＋232 ＋290 ＋108 ＋131 ＋165 ＋60 ＋83 ＋40 ＋63 ＋97
＋1090 ＋635 ＋730 ＋230 ＋230 ＋230 ＋135 ＋135 ＋135 ＋68 ＋68 ＋68 ＋20 ＋20 0 0 0
450 500
＋840 ＋480 ＋480

Remarks: In each row of the above table, upper values represent upper deviations and lower values represent lower deviations.

808
 ［Excerpt from JIS B 0401-2 (1998)］

Unit: μm

Classification
of basic size Tolerance class of hole
(mm)
Over Or less H9 H10 JS6 JS7 K6 K7 M6 M7 N6 N7 P6 P7 R7 S7 T7 U7 X7
＋25 ＋40 0 0 −2 −2 −4 −4 −6 −6 −10 −14 −18 −20
− 3 ±3 ±5 −
0 0 −6 −10 −8 −12 −10 −14 −12 −16 −20 −24 −28 −30
＋30 ＋48 ＋2 ＋3 −1 0 −5 −4 −9 −8 −11 −15 −19 −24
3 6 ±4 ±6 −
0 0 −6 −9 −9 −12 −13 −16 −17 −20 −23 −27 −31 −36
＋36 ＋58 ＋2 ＋5 −3 0 −7 −4 −12 −9 −13 −17 −22 −28
6 10 ±4.5 ±7.5 −
0 0 −7 −10 −12 −15 −16 −19 −21 −24 −28 −32 −37 −43
−33
10 14
＋43 ＋70 ＋2 ＋6 −4 0 −9 −5 −15 −11 −16 −21 −26 −51
±5.5 ±9 −
0 0 −9 −12 −15 −18 −20 −23 −26 −29 −34 −39 −44 −38
14 18
−56
−33 −46
18 24 −
＋52 ＋84 ＋2 ＋6 −4 0 −11 −7 −18 −14 −20 −27 −54 −67
±6.5 ±10.5
0 0 −11 −15 −17 −21 −24 −28 −31 −35 −41 −48 −33 −40 −56
24 30
−54 −61 −77
−39 −51 −71
30 40
＋62 ＋100 ＋3 ＋7 −4 0 −12 −8 −21 −17 −25 −34 −64 −76 −96
±8 ±12.5
0 0 −13 −18 −20 −25 −28 −33 −37 −42 −50 −59 −45 −61 −88
40 50
−70 −86 −113
−30 −42 −55 −76 −111
50 65
＋74 ＋120 ＋4 ＋9 −5 0 −14 −9 −26 −21 −60 −72 −85 −106 −141
±9.5 ±15
0 0 −15 −21 −24 −30 −33 −39 −45 −51 −32 −48 −64 −91 −135
65 80
−62 −78 −94 −121 −165
−38 −58 −78 −111 −165
80 100
＋87 ＋140 ＋4 ＋10 −6 0 −16 −10 −30 −24 −73 −93 −113 −146 −200
±11 ±17.5
0 0 −18 −25 −28 −35 −38 −45 −52 −59 −41 −66 −91 −131 −197
100 120
−76 −101 −126 −166 −232
−48 −77 −107 −155 −233
120 140
−88 −117 −147 −195 −273
＋100 ＋160 ＋4 ＋12 −8 0 −20 −12 −36 −28 −50 −85 −119 −175 −265
140 160 ±12.5 ±20

Limit Deviations for Fits Used Frequently (Holes)

0 0 −21 −28 −33 −40 −45 −52 −61 −68 −90 −125 −159 −215 −305
−53 −93 −131 −195 −295
160 180
−93 −133 −171 −235 −335
−60 −105 −149 −219 −333
180 200
−106 −151 −195 −265 −379
＋115 ＋185 ＋5 ＋13 −8 0 −22 −14 −41 −33 −63 −113 −163 −241 −368
200 225 ±14.5 ±23
0 0 −24 −33 −37 −46 −51 −60 −70 −79 −109 −159 −209 −287 −414
−67 −123 −179 −267 −408
225 250
−113 −169 −225 −313 −454
−74 −138 −198 −295 −455
250 280
＋130 ＋210 ＋5 ＋16 −9 0 −25 −14 −47 −36 −126 −190 −250 −347 −507
±16 ±26
0 0 −27 −36 −41 −52 −57 −66 −79 −88 −78 −150 −220 −330 −505
280 315
−130 −202 −272 −382 −557
−87 −169 −247 −369 −569
315 355
＋140 ＋230 ＋7 ＋17 −10 0 −26 −16 −51 −41 −144 −226 −304 −426 −626
±18 ±28.5
0 0 −29 −40 −46 −57 −62 −73 −87 −98 −93 −187 −273 −414 −639
355 400
−150 −244 −330 −471 −696
−103 −209 −307 −467 −717
400 450
＋155 ＋250 ＋8 ＋18 −10 0 −27 −17 −55 −45 −166 −272 −370 −530 −780
±20 ±31.5
0 0 −32 −45 −50 −63 −67 −80 −95 −108 −109 −229 −337 −517 −797
450 500
−172 −292 −400 −580 −860
Technical data
Product data/

809
 Limit Deviations for Fits Used Frequently (Shafts)
Limit deviations for frequently used fits of shafts
Classification
of basic size Tolerance class of shaft
(mm)
Over Or less b9 c9 d8 d9 e7 e8 e9 f6 f7 f8 g5 g6 h5 h6 h7
−140 −60 −20 −20 −14 −14 −14 −6 −6 −6 −2 −2 0 0 0
− 3
−165 −85 −34 −45 −24 −28 −39 −12 −16 −20 −6 −8 −4 −6 −10
−140 −70 −30 −30 −20 −20 −20 −10 −10 −10 −4 −4 0 0 0
3 6
−170 −100 −48 −60 −32 −38 −50 −18 −22 −28 −9 −12 −5 −8 −12
−150 −80 −40 −40 −25 −25 −25 −13 −13 −13 −5 −5 0 0 0
6 10
−186 −116 −62 −76 −40 −47 −61 −22 −28 −35 −11 −14 −6 −9 −15

10 14
−150 −95 −50 −50 −32 −32 −32 −16 −16 −16 −6 −6 0 0 0
−193 −138 −77 −93 −50 −59 −75 −27 −34 −43 −14 −17 −8 −11 −18
14 18

18 24
−160 −110 −65 −65 −40 −40 −40 −20 −20 −20 −7 −7 0 0 0
−212 −162 −98 −117 −61 −73 −92 −33 −41 −53 −16 −20 −9 −13 −21
24 30

−170 −120
30 40
−232 −182 −80 −80 −50 −50 −50 −25 −25 −25 −9 −9 0 0 0
−180 −130 −119 −142 −75 −89 −112 −41 −50 −64 −20 −25 −11 −16 −25
40 50
−242 −192
−190 −140
50 65
−264 −214 −100 −100 −60 −60 −60 −30 −30 −30 −10 −10 0 0 0
−200 −150 −146 −174 −90 −106 −134 −49 −60 −76 −23 −29 −13 −19 −30
65 80
−274 −224
−220 −170
80 100
−307 −257 −120 −120 −72 −72 −72 −36 −36 −36 −12 −12 0 0 0
−240 −180 −174 −207 −107 −126 −159 −58 −71 −90 −27 −34 −15 −22 −35
100 120
−327 −267
−260 −200
120 140
−360 −300
−280 −210 −145 −145 −85 −85 −85 −43 −43 −43 −14 −14 0 0 0
140 160
−380 −310 −208 −245 −125 −148 −185 −68 −83 −106 −32 −39 −18 −25 −40
−310 −230
160 180
−410 −330
−340 −240
180 200
−455 −355
−380 −260 −170 −170 −100 −100 −100 −50 −50 −50 −15 −15 0 0 0
200 225
−495 −375 −242 −285 −146 −172 −215 −79 −96 −122 −35 −44 −20 −29 −46
−420 −280
225 250
−535 −395
−480 −300
250 280
−610 −430 −190 −190 −110 −110 −110 −56 −56 −56 −17 −17 0 0 0
−540 −330 −271 −320 −162 −191 −240 −88 −108 −137 −40 −49 −23 −32 −52
280 315
−670 −460
−600 −360
315 355
−740 −500 −210 −210 −125 −125 −125 −62 −62 −62 −18 −18 0 0 0
−680 −400 −299 −350 −182 −214 −265 −98 −119 −151 −43 −54 −25 −36 −57
355 400
−820 −540
−760 −440
400 450
−915 −595 −230 −230 −135 −135 −135 −68 −68 −68 −20 −20 0 0 0
−840 −480 −327 −385 −198 −232 −290 −108 −131 −165 −47 −60 −27 −40 −63
450 500
−995 −635

Remarks: In each row of the above table, upper values represent upper deviations and lower values represent lower deviations.

810
 ［Excerpt from JIS B 0401-2 (1998)］

Unit: μm

Classification of
basic size Tolerance class of shaft
(mm)
Over Or less h8 h9 js5 js6 js7 k5 k6 m5 m6 n6 p6 r6 s6 t6 u6 x6
0 0 ＋4 ＋6 ＋6 ＋8 ＋10 ＋12 ＋16 ＋20 ＋24 ＋26
− 3 ±2 ±3 ±5 −
−14 −25 0 0 ＋2 ＋2 ＋4 ＋6 ＋10 ＋14 ＋18 ＋20
0 0 ＋6 ＋9 ＋9 ＋12 ＋16 ＋20 ＋23 ＋27 ＋31 ＋36
3 6 ±2.5 ±4 ±6 −
−18 −30 ＋1 ＋1 ＋4 ＋4 ＋8 ＋12 ＋15 ＋19 ＋23 ＋28
0 0 ＋7 ＋10 ＋12 ＋15 ＋19 ＋24 ＋28 ＋32 ＋37 ＋43
6 10 ±3 ±4.5 ±7.5 −
−22 −36 ＋1 ＋1 ＋6 ＋6 ＋10 ＋15 ＋19 ＋23 ＋28 ＋34
＋51
10 14
0 0 ＋9 ＋12 ＋15 ＋18 ＋23 ＋29 ＋34 ＋39 ＋44 ＋40
±4 ±5.5 ±9 −
−27 −43 ＋1 ＋1 ＋7 ＋7 ＋12 ＋18 ＋23 ＋28 ＋33 ＋56
14 18
＋45
＋54 ＋67
18 24 −
0 0 ＋11 ＋15 ＋17 ＋21 ＋28 ＋35 ＋41 ＋48 ＋41 ＋54
±4.5 ±6.5 ±10.5
−33 −52 ＋2 ＋2 ＋8 ＋8 ＋15 ＋22 ＋28 ＋35 ＋54 ＋61 ＋77
24 30
＋41 ＋48 ＋64
＋64 ＋76 ＋96
30 40
0 0 ＋13 ＋18 ＋20 ＋25 ＋33 ＋42 ＋50 ＋59 ＋48 ＋60 ＋80
±5.5 ±8 ±12.5
−39 −62 ＋2 ＋2 ＋9 ＋9 ＋17 ＋26 ＋34 ＋43 ＋70 ＋86 ＋113
40 50
＋54 ＋70 ＋97
＋60 ＋72 ＋85 ＋106 ＋141
50 65
0 0 ＋15 ＋21 ＋24 ＋30 ＋39 ＋51 ＋41 ＋53 ＋66 ＋87 ＋122
±6.5 ±9.5 ±15
−46 −74 ＋2 ＋2 ＋11 ＋11 ＋20 ＋32 ＋62 ＋78 ＋94 ＋121 ＋165
65 80
＋43 ＋59 ＋75 ＋102 ＋146
＋73 ＋93 ＋113 ＋146 ＋200
80 100
0 0 ＋18 ＋25 ＋28 ＋35 ＋45 ＋59 ＋51 ＋71 ＋91 ＋124 ＋178
±7.5 ±11 ±17.5
−54 −87 ＋3 ＋3 ＋13 ＋13 ＋23 ＋37 ＋76 ＋101 ＋126 ＋166 ＋232
100 120
＋54 ＋79 ＋104 ＋144 ＋210
＋88 ＋117 ＋147 ＋195 ＋273
120 140
＋63 ＋92 ＋122 ＋170 ＋248
0 0 ＋21 ＋28 ＋33 ＋40 ＋52 ＋68 ＋90 ＋125 ＋159 ＋215 ＋305

Limit Deviations for Fits Used Frequently (Shafts)

140 160 ±9 ±12.5 ±20
−63 −100 ＋3 ＋3 ＋15 ＋15 ＋27 ＋43 ＋65 ＋100 ＋134 ＋190 ＋280
＋93 ＋133 ＋171 ＋235 ＋335
160 180
＋68 ＋108 ＋146 ＋210 ＋310
＋106 ＋151 ＋195 ＋265 ＋379
180 200
＋77 ＋122 ＋166 ＋236 ＋350
0 0 ＋24 ＋33 ＋37 ＋46 ＋60 ＋79 ＋109 ＋159 ＋209 ＋287 ＋414
200 225 ±10 ±14.5 ±23
−72 −115 ＋4 ＋4 ＋17 ＋17 ＋31 ＋50 ＋80 ＋130 ＋180 ＋258 ＋385
＋113 ＋169 ＋225 ＋313 ＋454
225 250
＋84 ＋140 ＋196 ＋284 ＋425
＋126 ＋190 ＋250 ＋347 ＋507
250 280
0 0 ＋27 ＋36 ＋43 ＋52 ＋66 ＋88 ＋94 ＋158 ＋218 ＋315 ＋475
±11.5 ±16 ±26
−81 −130 ＋4 ＋4 ＋20 ＋20 ＋34 ＋56 ＋130 ＋202 ＋272 ＋382 ＋557
280 315
＋98 ＋170 ＋240 ＋350 ＋525
＋144 ＋226 ＋304 ＋426 ＋626
315 355
0 0 ＋29 ＋40 ＋46 ＋57 ＋73 ＋98 ＋108 ＋190 ＋268 ＋390 ＋590
±12.5 ±18 ±28.5
−89 −140 ＋4 ＋4 ＋21 ＋21 ＋37 ＋62 ＋150 ＋244 ＋330 ＋471 ＋696
355 400
＋114 ＋208 ＋294 ＋435 ＋660
＋166 ＋272 ＋370 ＋530 ＋780
400 450
0 0 ＋32 ＋45 ＋50 ＋63 ＋80 ＋108 ＋126 ＋232 ＋330 ＋490 ＋740
±13.5 ±20 ±31.5
−97 −155 ＋5 ＋5 ＋23 ＋23 ＋40 ＋68 ＋172 ＋292 ＋400 ＋580 ＋860
450 500
＋132 ＋252 ＋360 ＋540 ＋820
Technical data
Product data/

811
 Hardness Conversion Table［SAE J 417］Revised in 1983
Approximate Conversion Values for Rockwell C Hardness Values of Steel（1）
Brinell hardness
Rockwell superficial hardness
10 mm ball Load Rockwell hardness(3)
Diamond conical indenter

Shore hardness
3000 kgf Tensile
Rockwell strength Rockwell C
Vickers A scale D scale
C scale B scale 15-N 30-N 45-N (approximate scale
hardness Tungsten Load 60 kgf Load 100
Hardness(3) Standard Load 100 kgf scale scale scale value) MPa Hardness（3）
carbide Diamond kgf Diamond ｛kgf/mm2｝ （2）
ball Dia. 1.6 mm Load Load Load
ball conical conical
(1/16 in.) ball 15 kgf 30 kgf 45 kgf
indenter indenter
HRC HV HBS HBW HRA HRB HRD HR15N HR30N HR45N HS − HRC
68 940 − − 85.6 − 76.9 93.2 84.4 75.4 97 − 68
67 900 − − 85.0 − 76.1 92.9 83.6 74.2 95 − 67
66 865 − − 84.5 − 75.4 92.5 82.8 73.3 92 − 66
65 832 − （739） 83.9 − 74.5 92.2 81.9 72.0 91 − 65
64 800 − （722） 83.4 − 73.8 91.8 81.1 71.0 88 − 64
63 772 − （705） 82.8 − 73.0 91.4 80.1 69.9 87 − 63
62 746 − （688） 82.3 − 72.2 91.1 79.3 68.8 85 − 62
61 720 − （670） 81.8 − 71.5 90.7 78.4 67.7 83 − 61
60 697 − （654） 81.2 − 70.7 90.2 77.5 66.6 81 − 60
59 674 − （634） 80.7 − 69.9 89.8 76.6 65.5 80 − 59
58 653 − 615 80.1 − 69.2 89.3 75.7 64.3 78 − 58
57 633 − 595 79.6 − 68.5 88.9 74.8 63.2 76 − 57
56 613 − 577 79.0 − 67.7 88.3 73.9 62.0 75 − 56
55 595 − 560 78.5 − 66.9 87.9 73.0 60.9 74 2075｛212｝ 55
54 577 − 543 78.0 − 66.1 87.4 72.0 59.8 72 2015｛205｝ 54
53 560 − 525 77.4 − 65.4 86.9 71.2 58.6 71 1950｛199｝ 53
52 544 （500） 512 76.8 − 64.6 86.4 70.2 57.4 69 1880｛192｝ 52
51 528 （487） 496 76.3 − 63.8 85.9 69.4 56.1 68 1820｛186｝ 51
50 513 （475） 481 75.9 − 63.1 85.5 68.5 55.0 67 1760｛179｝ 50
49 498 （464） 469 75.2 − 62.1 85.0 67.6 53.8 66 1695｛173｝ 49
48 484 451 455 74.7 − 61.4 84.5 66.7 52.5 64 1635｛167｝ 48
47 471 442 443 74.1 − 60.8 83.9 65.8 51.4 63 1580｛161｝ 47
46 458 432 432 73.6 − 60.0 83.5 64.8 50.3 62 1530｛156｝ 46
45 446 421 421 73.1 − 59.2 83.0 64.0 49.0 60 1480｛151｝ 45
44 434 409 409 72.5 − 58.5 82.5 63.1 47.8 58 1435｛146｝ 44
43 423 400 400 72.0 − 57.7 82.0 62.2 46.7 57 1385｛141｝ 43
42 412 390 390 71.5 − 56.9 81.5 61.3 45.5 56 1340｛136｝ 42
41 402 381 381 70.9 − 56.2 80.9 60.4 44.3 55 1295｛132｝ 41
40 392 371 371 70.4 − 55.4 80.4 59.5 43.1 54 1250｛127｝ 40
39 382 362 362 69.9 − 54.6 79.9 58.6 41.9 52 1215｛124｝ 39
38 372 353 353 69.4 − 53.8 79.4 57.7 40.8 51 1180｛120｝ 38
37 363 344 344 68.9 − 53.1 78.8 56.8 39.6 50 1160｛118｝ 37
36 354 336 336 68.4 （109.0） 52.3 78.3 55.9 38.4 49 1115｛114｝ 36
35 345 327 327 67.9 （108.5） 51.5 77.7 55.0 37.2 48 1080｛110｝ 35
34 336 319 319 67.4 （108.0） 50.8 77.2 54.2 36.1 47 1055｛108｝ 34
33 327 311 311 66.8 （107.5） 50.0 76.6 53.3 34.9 46 1025｛105｝ 33
32 318 301 301 66.3 （107.0） 49.2 76.1 52.1 33.7 44 1000｛102｝ 32
31 310 294 294 65.8 （106.0） 48.4 75.6 51.3 32.5 43 980｛100｝ 31
30 302 286 286 65.3 （105.5） 47.7 75.0 50.4 31.3 42 950｛ 97｝ 30
29 294 279 279 64.7 （104.5） 47.0 74.5 49.5 30.1 41 930｛ 95｝ 29
28 286 271 271 64.3 （104.0） 46.1 73.9 48.6 28.9 41 910｛ 93｝ 28
27 279 264 264 63.8 （103.0） 45.2 73.3 47.7 27.8 40 880｛ 90｝ 27
26 272 258 258 63.3 （102.5） 44.6 72.8 46.8 26.7 38 860｛ 88｝ 26
25 266 253 253 62.8 （101.5） 43.8 72.2 45.9 25.5 38 840｛ 86｝ 25
24 260 247 247 62.4 （101.0） 43.1 71.6 45.0 24.3 37 825｛ 84｝ 24
23 254 243 243 62.0 100.0 42.1 71.0 44.0 23.1 36 805｛ 82｝ 23
22 248 237 237 61.5 99.0 41.6 70.5 43.2 22.0 35 785｛ 80｝ 22
21 243 231 231 61.0 98.5 40.9 69.9 42.3 20.7 35 770｛ 79｝ 21
20 238 226 226 60.5 97.8 40.1 69.4 41.5 19.6 34 760｛ 77｝ 20
（18） 230 219 219 − 96.7 − − − − 33 730｛ 75｝ （18）
（16） 222 212 212 − 95.5 − − − − 32 705｛ 72｝ （16）
（14） 213 203 203 − 93.9 − − − − 31 675｛ 69｝ （14）
（12） 204 194 194 − 92.3 − − − − 29 650｛ 66｝ （12）
（10） 196 187 187 − 90.7 − − − − 28 620｛ 63｝ （10）
（ 8） 188 179 179 − 89.5 − − − − 27 600｛ 61｝ （ 8）
（ 6） 180 171 171 − 87.1 − − − − 26 580｛ 59｝ （ 6）
（ 4） 173 165 165 − 85.5 − − − − 25 550｛ 56｝ （ 4）
（ 2） 166 158 158 − 83.5 − − − − 24 530｛ 54｝ （ 2）
（ 0） 160 152 152 − 81.7 − − − − 24 515｛ 53｝ （ 0）
Note (1) Figures in blue are based on ASTM E 140, Table 1 (jointly prepared by SAE, ASM and ASTM).
(2) The units and figures shown in parentheses { } following the listed values are the results of conversion from psi figures by reference to JIS Z 8413 and Z8438
conversion tables. For your reference, 1MPa＝1N/mm2
(3) The figures in parentheses ( ) are in ranges not frequently used. They are given as reference data.

812
SI Unit Conversion Table / Weight & Measure Conversion Table [Excerpt from JIS Handbook]
Conversion rate of JIS units upon switchover to SI units (units in red are SI Units)

Pressure Specific heat

2 mmHg or J/（kg･K） kcal/（kg･°C）、cal/（g･°C）
Pa bar kgf/cm atm mmH2O
Torr 1 2.388 89×10−4
−5 −5 −6 −1 −3
4.186 05×103 1
1 1×10 1.019 72×10 9.869 23×10 1.019 72×10 7.500 62×10
Note: 1cal＝4.186 05J (by Measurement Act)
1×105 1 1.019 72 9.869 23×10−1 1.019 72×104 7.500 62×102
4 −1 −1 4 2
9.806 65×10 9.806 65×10 1 9.678 41×10 1×10 7.355 59×10
Coefficient of heat transfer
1.013 25×105 1.013 25 1.033 23 1 1.033 23×104 7.600 00×102
−5 −4 −5 −2 W/（m2･K） kcal/（h･m2･°C）
9.806 65 9.806 65×10 1×10 9.678 41×10 1 7.355 59×10
1 8.600 0×10−1
1.333 22×102 1.333 22×10−3 1.359 51×10−3 1.315 79×10−3 1.359 51×10 1
1.162 79 1
Note: 1Pa＝1N/m2 Note: 1cal＝4.186 05J (by Measurement Act)

Power (process rate, power), heat flow

kW kgf･m/s PS kcal/h Note: 1W＝1J/s, PS: French horse power
1 1.019 72×102 1.359 62 8.600 0×102 1PS＝0.735 5kW (by Act for Enforcement of Measurement Act)
9.806 65×10−3 1 1.333 33×10−2 8.433 71 1cal＝4.186 05J (in accordance with Measurement Act)
7.355×10−1 7.5×10 1 6.325 29×102
1.162 79×10−3 1.185 72×10−1 1.580 95×10−3 1

Stress Work, energy & quantity of heat

Pa MPa or N/mm2 kgf/mm2 kgf/cm2 J kW･h kgf･m kcal

Hardness Conversion Table

SI Unit Conversion Table/Weight & Measure Conversion Table
1 1×10−6 1.019 72×10−7 1.019 72×10−5 1 2.777 78×10−7 1.019 72×10−1 2.388 89×10−4
1×106 1 1.019 72×10−1 1.019 72×10 3.600×106 1 3.670 98×105 8.600 0×102
9.806 65×106 9.806 65 1 1×102 9.806 65 2.724 07×10−6 1 2.342 70×10−3
9.806 65×104 9.806 65×10−2 1×10−2 1 4.186 05×103 1.162 79×10−3 4.268 58×102 1
Note: 1J＝1W･s、1J=1N･m
1cal＝4.186 05J (by Measurement Act)

Weight & measure Conversion Table

Measure comparison table Volume comparison table

Cubic Gallon Gallon
Shaku Kan Meter Inch Feet Yard Go Liter Cubic inch
centimeters (UK) (US)

1 0.166667 0.30303 11.9303 0.994194 0.33140 1 180.39 0.18039 0.03968 0.04765 11.01
6 1 1.81818 71.5819 5.96516 1.98839 0.00554 1 0.001 0.00022 0.00026 0.06102
3.3 0.55 1 39.3701 3.28084 1.09361 5.5435 1000 1 0.21997 0.26417 61.024
0.08382 0.01397 0.0254 1 0.08333 0.02778 25.2 4546.09 4.54609 1 1.20095 277.42
1.00584 0.16764 0.3048 12 1 0.33333 20.98 3785.41 3.78541 0.833 1 231
3.01752 0.50292 0.9144 36 3 1 0.0908 16.3871 0.01639 0.0036 0.0043 1

Weight comparison table

Ka Kin Gram Ton (UK) Ton (US) Ounce Pound

1 6.25 3750 0.003691 0.004134 132.277 8.26733

0.16 1 600 0.000591 0.000661 21.1644 1.32277
0.000267 0.001667 1 0.00000098 0.0000011 0.035274 0.0022046
Technical data
Product data/

262.4543 1640.339 1016050 1 1.12 35840 2240

241.916 1511.975 907185 0.892857 1 32000 2000
0.007569 0.047249 28.3495 0.000028 0.000031 1 0.0625
0.120958 0.755987 453.5924 0.000446 0.0005 16 1

813
814
 INFORMATION OF OUR BUSINESS
Customer Guide
■New Proposition for In-Mold Resin Pressure Measurement,
   MOLD MARSHALLING SYSTEM ・・・・・・・・・・・・・・・・・・・・ P.816
■Company Profile ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.818

■Catalog Request ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.820

 Mold Marshalling System

What is Mold Marshalling System?

Mold marshalling system is a measuring system for injection
molding that visualizes resin behavior inside the mold, which
has been a black box so far. It uses a sensor mounted inside
PC the mold and a special amplifier installed outside to measure
in-mold resin temperature and pressure, convert them into
electrical signals or voltages and output the data on the PC or
Pressure sensor
various measuring devices. Quantified data can be used for
Relay box
various purposes such as automated selection of defective
MPS08 (Pressure measuring amplifier)
LAN connection (can be disconnected to allow the products, quality control, evaluation of molds, etc.
amplifier to monitor alarm standalone).

Features

A variety of measurement & monitoring functions

Ejector pin shaped pin sensor that

can be easily mounted in the mold.
Low cost

Easy to use
Visualize the in-mold resin temperature
and pressure with waveforms.
Functional

Compact

An example of measurement screen Examples of molding defects that can be determined from in-mold pressure values.
In-mold pressure

Waveform rises
(Flash, over-packing
occurs)

Good product
waveform

Waveform falls (Short

mold, sink mark occurs)

突出し抵抗値
離型性の判定

Time

816
 Benefits of in-mold resin pressure measurements

• Alarm signals triggered by fluctuations in waveform with respect to a reference waveform

Detection of defective products notify the occurrence of molding defects such as short shots and over packing, etc.

Setting of molding conditions according to • By saving a waveform when a good product has been produced and performing molding
changes in molding machine or environment operations with the waveform, the same quality of molded products can be produced.

• By analyzing the time required until the resin reaches the sensor and the pressure during the
Analysis of mold structure and resin flow period, products of uniform quality can be achieved at the time of multi-cavity molding.

Identification of relations of in-mod • The type of potential defects can be projected by checking the pressure waveform against the
pressure and molding defects good product waveform (reference waveform).

Benefits of in-mold resin temperature measurement

Actual measurement of • Accurate grasp of in-mold temperature is now possible.

resin temperature Fast 8 ms response time for high-speed actual measurement. Contactless temperature measurement system (optical fiber infrared system)

Detection of defective • Alarm signals triggered by fluctuations in waveform with respect to a reference waveform
products notify the occurrence of molding defects such as short shots, sink marks, and gas burning, etc.

Optimization of molding
• Molding conditions can be optimized through resin temperature controls
conditions

Comparison with CAE • By comparing the CAE comparison results with the actual measurement, the data can be
Analysis effectively utilized to improve the accuracy of CAE analysis.

817
 Company Profile

Futaba’s high technology connects dreams and

future of people and society
Modern society is progressing rapidly and its needs becoming increasingly diversified.
To respond to these needs, and helps the society develop further and achieve more in
the future, advanced technologies are required. By utilizing its accumulated advanced
technologies and experiences, Futaba is dedicated to developing new products that are
needed and useful in every aspect of life, thereby contributing to dreams and future of
people and society.

“Supports Manufacturing”

Machinery & Provides a wide variety of components and equipments that realize streamlining
tooling Division production of molds, which become the source of every product

818
“Eye Communication”

Electronic Fluorescent display tubes boasting superior performance and reliability. We respond to
Components Division needs flexibly with our advanced technology and a strong product development capability.

Electronic Systems Radio control systems with overwhelming popularity appeals Futaba’s advanced
Division technology to the world.

Nurturing dreams Propositions to industries

Radio control devices for hobby Radio control devices for commercial use

819
 Catalog Request

Please use our catalogs as an aid while designing plastic

molding line or developing tools.

For plastic molds

Futaba Standard

Plastic Mold Components

Blue Book

BLUE BOOK Plastic Mold Components Edition BLUE BOOK Additional Mold Base Processing & Mold Parts Edition

For molds & equipment

RED BOOK Plate General Catalog Red Book for Equipment

For in-mold resin temp. & pressure measuring system For stamping molds

System for measuring resin pressure inside molds

MOLD
MARSHALLING
SYSTEM
金型用部品
®

グリーンブック
VOL.5

Mold Marshalling System Green Book Stamping Mold Components

For stamping & plastic molding lines

プレス・モールド関連

省力機器
総合カタログ 送り装置

AFE 小形エアフィーダ

VOL.5
AFE ベルトフィーダ

AFA 自動機向けエアフィーダ

NC グリップフィーダ

NC ロールフィーダ

繰出し／巻取り装置

オートリール

リールスタンド

テンションリール

コムリール

ユニットレベラ

コイルクレードル

Power Saving Device General Catalog

820
memo

821
 Code Index
Code Name and description Page

A
A Cavity Plates (Fixed Half) 22, 286, 484, 678
AAS Aluminum Alloy A7075 or Equivalent 802

B
B Cavity Plates (Moving Half) 22, 286, 484, 678

C
C Spacer Blocks 22, 286, 484, 678

D
D Series 3-Plate Type D Series 286
D•E Series 3-Plate Type D & E Series 286
D•E Series Material Change Option 3-Plate Type D & E Series Material Change Option 480
DA Type D Series, Ejector Pin Ejection Type 287
DB Type D Series, Stripper Plate Ejection Type 287
DC Type D Series, Ejector Pin Ejection Type without Backing Plate 287
DD Type D Series, Stripper Plate Ejection Type without Backing Plate 287
DE Type D Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior 287
DF Type D Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior, without Backing Plate 287

E
E Ejector Retainer Plates 22, 286, 484, 678
E Series 3-Plate Type E Series 286
EA Type E Series, Ejector Pin Ejection Type without Runner Plate 287
EB Type E Series, Stripper Plate Ejection Type without Runner Plate 287
EC Type E Series, Ejector Pin Ejection Type without Runner Plate and Backing Plate 287
ED Type E Series, Stripper Plate Ejection Type without Runner Plate and Backing Plate 287

F
F Ejector Base Plate 22, 286, 484, 678
F Series 3-Plate Type F Series 484
F•G Series 3-Plate Type F & G Series 484
F•G Series Material Change Option 3-Plate Type F & G Series Material Change Option 674

FA Type F Series, Ejector Pin Ejection Type 485

FC Type F Series, Ejector Pin Ejection Type without Backing Plate 485
FE Type F Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior 485
FF Type F Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior without Backing Plate 485
F-S55C Carbon Steels for Mechanical Structure 798

G
G Series 3-Plate Type G Series 484
GA Type G Series, Ejector Pin Ejection Type without Runner Plate 485
GC Type G Series, Ejector Pin Ejection Type without Runner Plate and Backing Plate 485

822
Code Name and description Page

H
H Series 3-Plate Type H Series 678
HA Type H Series, Ejector Pin Ejection Type 679
HB Type H Series, Stripper Plate Ejection Type 679
HC Type H Series, Ejector Pin Ejection Type without Backing Plate 679
HD Type H Series, Stripper Plate Ejection Type without Backing Plate 679
HPM1 Prehardened Steel for Plastic Mold 799

K
KABB NISSEI FP SYSTEM/ Base Blocks (Please refer to each exclusive catalogue for the details) 724
KASP NISSEI FP SYSTEM/ Maintenance Parts (Please refer to each exclusive catalogue for the 724
KAUM NISSEI FP SYSTEM/ Unit Mold (Please refer to each exclusive catalogue for the details) 724

L
L Bottom Clamping Plates 22, 286, 484, 678

M
M-PLLA Parting Locks (Sets) 717
M-PLLS Parting Locks (Plastic Sleeve) 717
M-PLLM Parting Locks (Tapered Bolt) 717
M-SBA Sprue Bushings for QMC 717
MDB Cavity Retainer Sets 728
MDCZSFHS Sumitomo Cassette Mold Base M5/7，M8/7 Standard Type Holders 720
0120 × 0120 (Please refer to each exclusive catalogue for the details)
MDCZSFHS Sumitomo Cassette Mold Base M26/15 Standard Type Holders 720
0150 × 0200 (Please refer to each exclusive catalogue for the details)
MDCZSFHW Sumitomo Cassette Mold Base M5/7，M8/7 Split Type Holders 720
0120 × 0170 (Please refer to each exclusive catalogue for the details)
MDCZSFHW Sumitomo Cassette Mold Base M26/15 Split Type Holders 720
0150 × 0200 (Please refer to each exclusive catalogue for the details)
MDCZSFPG Sumitomo Cassette Mold Base M5/7，M8/7 Standard Type 3-Plate 720
0120 × 0120 (Please refer to each exclusive catalogue for the details)
MDCZSFPG Sumitomo Cassette Mold Base M5/7，M8/7 Split Type 3-Plate 720
0120 × 0170 (Please refer to each exclusive catalogue for the details)
MDCZSFPG Sumitomo Cassette Mold Base M26/15 3-Plate 720
0150 × 0200 (Please refer to each exclusive catalogue for the details)
MDCZSFSG Sumitomo Cassette Mold Base M5/7，M8/7 Standard Type 2-Plate 720
0120 × 0120 (Please refer to each exclusive catalogue for the details)
MDCZSFSG Sumitomo Cassette Mold Base M5/7，M8/7 Split Type 2-Plate 720
0120 × 0170 (Please refer to each exclusive catalogue for the details)
MDCZSFSG Sumitomo Cassette Mold Base M26/15 2-Plate 720
0150 × 0200 (Please refer to each exclusive catalogue for the details)
MDCZSFWS Sumitomo Cassette Mold Base M5/7，M8/7 Split Type 720
0120 × 0170 (Please refer to each exclusive catalogue for the details)
MDCZSFWS Sumitomo Cassette Mold Base M26/15 Split Type 720
0150 × 0200 (Please refer to each exclusive catalogue for the details)
MDE Cavity Retainer Sets for Die Cast 762

N
NAK55 Prehardened Steel for Plastic Mold 800
NAK80 Prehardened Steel for Plastic Mold 800

823
 Code Index
Code Name and description Page

Q
QMC Quick Mold Changer for Plastic Mold 712
(Please refer to each exclusive catalogue for the details)
QMC-IPA Insert Unit, 3-Plate Type, Ejector Pin Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMC-IPB Insert Unit, 3-Plate Type, Stripper Plate Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMC-IPC Insert Unit, 3-Plate Type, Ejector Sleeve Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMC-ISA Insert Unit, 2-Plate Type, Ejector Pin Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMC-ISB Insert Unit, 2-Plate Type, Stripper Plate Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMC-ISC Insert Unit, 2-Plate Type, Ejector Sleeve Ejection Type 716
(Please refer to each exclusive catalogue for the details)
QMCAH QMC Type A: Holders for Both 2 & 3 Plate Molds 715
(Please refer to each exclusive catalogue for the details)
QMCBH QMC Type B: Holders for 2-Plate Mold Base 714
(Please refer to each exclusive catalogue for the details)

R
R Runner Plates 286, 484, 678

S
S Stripper Plates 22, 286, 484, 678
S Series 2-Plate Type S Series 22
S Series Material Change Option 2-Plate Type S Series Material Change Option 260
SA Type S Series, Ejector Pin Ejection Type 23
SB Type S Series, Stripper Plate Ejection Type 23
SC Type S Series, Ejector Pin Ejection Type without Backing Plate 23
SD Type S Series, Stripper Plate Ejection Type without Backing Plate 23
SE Type S Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior 23
SF Type S Series, Stripper Plate Ejection Type, Which is Actuated by Mold Opening Behavior without Backing Plate 23

T
T Top Clamping Plate 22, 286, 484, 678

U
U Backing Plate 22, 286, 484, 678

Discontinued standard products

＊ Mold bases with pockets and temperature control holes…Please order by additional processing.
＊ Mold bases with pockets …Please order by additional processing.
＊ Mold bases with temperature control holes…Please order by additional processing
＊ Clamping plate specification (dedicated clamping plate for Yamashiro) of nominal dimension 1515 in S series
＊ Nominal dimension 1515 types in D & E series
＊ Nominal dimension 2024 types in S series, D & E series, F & G series and cavity retainer sets
＊ Arburg mold bases

824
memo

825
 BLUE BOOK Plastic
Mold Components VOL. 1
Published March, 2014 Initial Edition

Futaba Corporation
629 Oshiba, Mobara, Chiba Prefecture 297- 8588, Japan

URL http://www.futaba.co.jp/
copyright C 2011 by FUTABA CORPORATION
All right Reserved. 1403ABE
 Safety Precautions
● Check the weight of the mold base and plates and take necessary safety measures before performing operations.
The weight of the merchandize is indicated on the address label placed on the top surface of the carton. When
transporting or moving heavy goods, only qualified personnel who have completed the required skill training courses
such as those for “crane operations”, “slinging operation” and “forklift operations” should operate suspension
equipment, and perform slinging and forklift operations in accordance with the Industrial Safety and Health Act.
● When disassembling or assembling mold bases and main molds, etc., care must be taken not to get your hand or
finger caught between the parting surfaces. Also, adequate precautions should be taken to prevent mold bases or
main molds from falling off from the parting line, resulting in an injury or accident.
● Some merchandizes may have sharp edges depending on the contents of order (specifications and structure).
Please use extreme care when handling these merchandizes.

◎ About inquiry: If you have any inquiries about this catalog, contact your nearest Futaba office or sales office.
◎ The contents of this catalog is as of March, 2014. Specifications and dimensions herein are subject to change
without notice due to design improvement.
◎ Consumption tax: The prices shown in this catalog do not include consumption tax. The tax will be added to
the price.
◎ Shipping fee: Shipping fee will be separately charged.
◎ Export Control: If you export MOLDZUKAN overseas, the export might be regulated under the Foreign Exchange
and Foreign Trade Act, depending on the use of the software (is or is likely to be used or diverted for devel-
oping weapons). Before exporting MOLDZUKAN, you should make sure whether or not the export is subject
to regulations in accordance with the act and take necessary procedures such as obtaining a license, etc.
The products listed in other catalogs do not fall under the paragraph 1 to 15, Appended Table 1 of Foreign
Exchange Table, however, they fall under the paragraph 16 of Catch-All Controls that has been introduced in
April 2002. Also, please note that if they are exported, combined with other devices, they may be subject to
the Foreign Exchange Law or Foreign Trade Law.

Marketing & Sales Group

Chosei Machinery & Tooling Technology Center, 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba Prefecture,
299-4395, Japan

TEL.0475-30-0809 FAX.0475-30-0818

URL http://www.futaba.co.jp/
 Korea
Kishin Corporation
Japan
China Futaba Corporation
Machinery & Tooling Division,
Kishin Precision Die & Mold Machinery (TianJin) Co., Ltd.
Marketing & Sales Group
Kishin Precision Die & Mold Machinery (China) Co., Ltd.
Futaba International Trading (Shanghai) Co., Ltd.
Hong Kong
Futaba Precision Mold (Shenzhen) Corp. Ltd.
Futaba (Hong Kong) Co., Ltd.

Thailand
Indonesia
FUTABA JTW（THAILAND）LTD.
PT.FutabaDenshi Indonesia
Vietnam
… Sales office FUTABA（VIETNAM）CO., LTD.
… Production facility

KISHIN CORPORATION KISHIN PRECISION DIE AND MOLD FUTABA PRECISION DIE AND MOLD
TEL.82-32-815-0222 ∼ 8 MACHINERY (TIANJIN) CO.,LTD. MACHINERY (CHINA) CO.,LTD.
FAX.82-32-814-7188 TEL.86-22-8396-8801 TEL.86-512-57035900
URL http://www.kishin.com FAX.86-22-8396-8802 FAX.86-512-57035840

FUTABA PRECISION MOULD FUTABA (Hong Kong) CO.,LTD. FUTABA International Trading
(SHENZHEN) CORP., LTD. TEL.852-2563-6141  (Shanghai) CO.,LTD.
TEL.86-755-84736190 FAX.852-2811-0802 TEL.86-21-50366399
FAX.86-755-84736197 URL http://www.futabahk.com.hk/ FAX.86-21-50366386

FUTABA JTW (THAILAND) LTD. FUTABA (VIETNAM) CO., LTD. PT.FutabaDenshi Indonesia
TEL.66-38-522-270 ∼ 4 TEL.84-8-3-7700-551 ∼ 5 TEL.62-21-292-88616
FAX.66-38-522-275 FAX.84-8-3-7700-550 FAX.62-21-292-88617
URL http://www.fjthai.com
«Futaba Corporation (in Japan)»
Headquarters
629 Oshiba, Mobara, Chiba Prefecture 297-8588, Japan Germany
TEL: 81-475-24-1111 FAX: 81-475-23-1346
U.S.A

Marketing & Sales Office Chicago Detroit

□Makuhari Marketing & Sales Center (Electronic Compornents)

Makuhari Techno-garden B6, 1-3 Nakase, Mihama-ku, Chiba, 261-8555, Japan Korea

TEL: 81-43-296-5111 FAX: 81-43-296-5121 China

Japan
□Machinery & Tooling Division
1080-Yabutsuka, Chosei-mura, Chosei, Chiba Prefecture 299-4395, Japan Taiwan
Vietnam
TEL: 81-475-30-0809 FAX: 81-475-30-0818 Thailand
Philippines

«Overseas Affiliates»
Singapore
Asia Overseas Affiliates
Machinery & Tooling Division
□FUTABA (Hong Kong) Corporation, Ltd.
Indonesia
Electronic Components Division
Electronic Systems Divisionivision
18F.,The Cameron, 33 Cameron Road, Tsim Sha Tsui, Kowloon, Hong Kong
TEL: 852-2563-6141 FAX: 852-2811-0802
□ FUTABA Precision Mould (Shenzhen) Corp., Ltd.
No.1 Futaba Road, Danzhutou Industrial Estate, Nanwan Street, Longgang, North America
Shenzhen, Guangdong, China
TEL: 86-755-84736190 FAX: 86-755-84736197 □ FUTABA Corporation of America
Chicago Office
□ FUTABA International Trading (Shanghai) Co., Ltd. 711 E. State Parkway Schaumburg, Illinois 60173, U.S.A.
Unit F, 8/F, International Ocean Shipping & Finance Center, No.720 Pudong TEL: 1-847-884-1444 FAX: 1-847-884-1635
Avenue, Pudong New District, Shanghai, China
TEL: 86-21-50366399 FAX: 86-21-50366386 Detroit Office
Shenzhen Office 14492 Sheldon Road, Suite #370, Plymouth, Michigan 48170, U.S.A.
Room07, 13F, Office Tower, Shun Hing Square, Di Wang Commercial Centre, TEL: 1-734-459-1177 FAX: 1-734-459-1268
5002 Shen Nan Dong Road, Luohu, Shenzhen, Guangdong, China Huntsville Office
TEL: 86-755-8207-0299 FAX: 86-755-2583-0083 101 Electronics Boulevard, Huntsville, Alabama 35824, U.S.A.
□ FUTABA Precision Die and Mold Machinery (China) Co., Ltd. TEL: 1-256-461-9399 FAX: 1-256-461-1059
1098 Fuchunjiang Road, Kunshan, Jiangsu, 215300, China El Paso (Distribution Center)
TEL: 86-512-57035900 FAX: 86-512-57035840 24 Spur Dr, El Paso, TX, United States
TEL: 1-915-771-7858
□ FUTABA Corporation of Huizhou
16 Zhongkai Hi-Tech Industrial Development Zone, Huizhou, Guangdong, China
TEL: 86-752-2627111 FAX: 86-752-2627118 □ FUTABA (Europe) GmbH
□ Kishin Precision Die and Mold Machinery (Tianjin) Co., Ltd. Halskestrasse 9, D-47877 Willich, Germany
No.3 4th Branch Road, 2nd Saida Avenue, Xiqing Economic Development TEL: 49-2154-943-0 FAX: 49-2154-943-200
Area, Tianjin, China
TEL: 86-22-8396-8801 FAX: 86-22-8396-8802
«Affiliates in Japan»
□ FUTABA Electronics (Beijing) Co., Ltd.
101, A-14, Tiantan Dongli Zhongqu, Dongcheng District, Beijing, 100061, China □ FUTABA Industry Co., Ltd.
TEL: 86-10-67050717 FAX: 86-10-67050576 Miyakawa Bldg., 2-9 Kanda Suda-cho, Chiyoda-ku, Tokyo 101-0041, Japan
TEL: 81-3-3255-9984 FAX: 81-3-3251-9984
□ FUTABA DENSHI Corp. (S) Pte. Ltd.
152 Beach Road, The Gateway East, #23-08, Singapore 189721 □ FUTABA Business System Co., Ltd.
TEL: 65-6291-9882 FAX: 65-6291-7391 599 Oshiba, Mobara, Chiba Prefecture 297-0033, Japan
TEL: 81-475-26-0192
□ Taiwan FUTABA Electronics Corporation
No.1 Shing Kai Fa Road, Nan Tze Export Processing Zone, Kaohsiung, Taiwan □ O.S.ENGINES Mfg. Co., Ltd.
TEL: 886-7-3646516~7 FAX: 886-7-3642876 6-15 Imagawa 3-Chome, Higashi-Sumiyoshi-ku, Osaka Prefecture 546-0003, Japan
Taipei Office TEL: 81-6-6702-0225 FAX: 81-6-6704-2722
Room 3G03, No.5, Hsin-Yi Road, Sec.5, Taipei 11011, Taiwan,R.O.C □ Futaba Precision Co., Ltd.
TEL: 886-2-8789-5068 FAX: 886-2-8789-5069 10-159-2 Kasshi-cho, Kamaishi, Iwate Prefecture 026-0055, Japan
□ Kishin Corporation TEL: 81-193-23-0241 FAX: 81-193-25-1706
111 Eunbong-ro, Namdong-gu, Incheon, 405-849 Korea □ SATSUKI KIZAI CO., LTD.
TEL: 82-32-815-0222~8 FAX: 82-32-814-7188 598-1 Monoi, Yotsukaido, Chiba Prefecture 284-0012, Japan
□ SAMILMEGATEC Co., Ltd. TEL: 81-43-422-1447 FAX: 81-43-422-1435
466-7 Hyundai-Kia St, Hwaseong-si, Gyeonggi-do,445-020 Korea □ Futaba Mobile Display Corporation.
TEL: 82-31-355-9811 FAX: 82-31-355-9820 644-55, Hitana, Nakago-cho,Kitaibaraki,Ibaraki,319-1556,Japan
□ Futaba Electronics Components Korea Co., Ltd. TEL: 81-293-43-6788 FAX: 81-293-43-6722
A-1410, Woolim Lions Valley, Gasan digital 1-ro 168,Gasan-dong, Geumcheon-gu,
Seoul, Korea
TEL: 82-2-2026-2512 FAX: 82-2-2026-2514
□ FUTABA Corporation of The Philippines
120 North Science Avenue, Laguna Technopark-SEPZ, Binan, Laguna, Philippines
TEL: 63-2-843-2866 FAX: 63-2-843-2898
□ FUTABA JTW (Thailand) Ltd.
78 Moo 2 Wellgrow Industrial Estate, Bangna-Trad Road, Tambon Pimpa,
A.Bangpakong, Chachoengsao 24180, Thailand
TEL: 66-38-522270~4 FAX: 66-38-522275
□ FUTABA(Vietnam)CO.,LTD.
Road 12 Tan Thuan E.P.Z. Tan Thuan Dong Ward, District 7 Ho Chi Minh City, Vietnam
TEL: 84-8-3-7700-551~5 FAX: 84-8-3-7700-550
□ PT.FutabaDenshi Indonesia
Jl. Trembesi Blok F19 No. 1A, Delta Silicon 3 Industrial Park, Desa Cicau, Kec.
Cikarang Pusat, Lippo Cikarang, Kab. Bekasi, Provinsi Jawa Barat, Indonesia
TEL: 62-21-292-88616 FAX: 62-21-292-88617