Thrust and Electrical Power by Rectifying Aether/ZPE

with Chaos Converters - 03/01/00

for KeelyNet by Jerry W. Decker

This paper and the associated images are intended to illustrate how aether/zpe can be envisioned
as energy popping into and out of existence to produce mechanical thrust OR electrical energy
as described by Puthoff/Haisch/Rueda as a 'Quantum Vacuum/Foam'(excerpted quote below)
and by Henry Moray, Sr. as a 'Sea of Energy'.

The theory rests on many assumptions, and the one that worries us is the most fundamental:
that the quantum vacuum produces a real electromagnetic field. Physicists normally treat the
virtual photons as just that: virtual, hence unable to produce any far-reaching real effects. But
numerous experiments indicate the field may indeed influence matter.

The quantum vacuum creates an attraction between neutral parallel plates, as predicted by
Dutch physicist Hendrick Casimir in 1948 and confirmed experimentally several years later. The
interaction of the vacuum electromagnetic field with electrons causes a shift of hydrogen spectral
lines, as discovered by American physicists Willis Lamb Jr. and Robert Retherford in 1947 and
explained later that year by Hans Bethe. And the spontaneous emission of photons can be
altered by changing the electromagnetic environment of atoms; this suggests that ``spontaneous''
emission is actually stimulated by the fluctuations of the vacuum.

Distances for Casimir plates.

"...The Casimir force is a short range attraction between any two objects caused by ...
electromagnetic fluctuations in the vacuum. ... any two plates, whether conductor or dielectrics,
would experience a fourth power force law ... also proportional to the dielectric constant of the
plates. ... The equations are only valid down to a separation distance proportional to the
minimum wavelength at which the plates are still a good conductor or the dielectric constant is
not unity. For distances closer than that ... attractive force will ... increase ... at a rate
proportional to the third power of the separation distance. ...

"... The closest separation distance ...[that has been attained is 14

Angstroms]... (about five atoms) with two crossed cylinders of mica.
... the measured force between the two mica cylinders was over ten
tons per square meter! ... [To construct a vacuum fluctuation
battery, make] ... a wide flat spiral of foil built along the lines of a
Slinky toy. ... each turn of the spiral acts against the neighboring
turns. The spiral configuration allows substantial compaction of the
foil from large spacings to small spacings while maintaining uniform
spacing. ... [electric charge could] create an electrostatic repulsion between the plates ... The
Casimir force [could] draw the ... leaves together, doing work against the repulsive electric field
...".

Using Aether/ZPE as a propulsive force

Several experimental formats for tapping the ZPE for practical use are under investigation in
our laboratory. An early one of interest is based on the idea of a Casimir pinch effect in non-
neutral plasmas, basically a plasma equivalent of Forward's electromechanical charged-plate
collapse (see Puthoff, 1990). The underlying physics is described in a paper submitted for
publication by myself and M. Piestrup, and it is illustrative that the first of several patents issued
to a consultant to our laboratory, K.R. Shoulders, contains the descriptive phrase "... energy is
provided... and the ultimate source of this energy appears to be the zero-point radiation of the
vacuum continuum."

".... Many researchers see the vacuum as a central ingredient of 21st- Century physics. Some
even believe the vacuum may be harnessed to provide a limitless supply of energy. This report
summarizes an attempt to find an experiment that would test the Haisch, Rueda and Puthoff
(HRP) conjecture that the mass and inertia of a body are induced effects brought about by
changes in the quantum-fluctuation energy of the vacuum.... It was possible to find an
experiment that might be able to prove or disprove that the inertial mass of a body can be
altered by making changes in the vacuum surrounding the body."

In 1958 Dutch physicist M.J. Spaarnay carried out a series of experiments based on Casimir's
proposal and found that the force did not approach zero when the thermal radiation was
reduced to low intensity. Instead there was a residual attractive force that would persist even at
absolute zero.

The residual force is directly proportional to the area of the plates and inversely proportional to
the fourth power of their separation; the constant of proportionality is 1.3 X 10-18th erg-
centimeter.

Although such a force is small, it is measurable if the plates are sufficiently close together. For
plates with an area of one square centimeter separated by .5 micrometer the Casimir force is
equivalent to the weight of .2 milligram.

For the purposes of this paper, the radiations from aether/zpe quanta
are thought to emanate from all surface areas as they pop in and out of
existence.
This all pervading quantum foam would appear as 'noise' as described in a recent fascinating
article in New Scientist - Random Reality.

Space and the material world could be created out of nothing but noise. That's the startling
conclusion of a new theory that attempts to explain the stuff of reality, as Marcus Chown reports

IF YOU COULD LIFT A CORNER of the veil that shrouds reality, what would you see
beneath? Nothing but randomness, say two Australian physicists. According to Reginald Cahill
and Christopher Klinger of Flinders University in Adelaide, space and time and all the objects
around us are no more than the froth on a deep sea of randomness.

Perhaps we shouldn't be surprised that randomness is a part of the Universe. After all,
physicists tell us that empty space is a swirling chaos of virtual particles. And randomness comes
into play in quantum theory--when a particle such as an electron is observed, its properties are
randomly selected from a set of alternatives predicted by the equations.

But Cahill and Klinger believe that this hints at a much deeper randomness. "Far from being
merely associated with quantum measurements, this randomness is at the very heart of reality,"
says Cahill. If they are right, they have created the most fundamental of all physical theories,
and its implications are staggering. "Randomness generates everything," says Cahill. "It even
creates the sensation of the 'present', which is so conspicuously absent from today's physics."

A better definition of what is Zero Point Energy comes from the University of Virginia and says;

All objects in our universe have wave-like characteristics that manifest themselves in certain
circumstances. These wave-like characteristics become more significant as objects becomes
smaller. Their wave-like characteristics allow small particles to have ill-defined locations.

To understand what I mean by "ill-defined locations", consider a wave on the surface of a lake.
There is no one point at which this wave is located--it is located over a region of the water's
surface. Waves don't have well defined locations.

Similarly, if you observe an electron, which is really a wave, there is no one point at which that
electron is located--it is located over a region of space. Because of the detailed relationships
between wavelength, frequency, and energy, the smaller the region of space in which the
electron-wave can be found, the higher its energy must be.

Thus an electron that is localized at all--that is known to be within a certain region of space--
must have a certain minimum energy, even if it is stationary. This minimum energy is called
zero point energy and it is a consequence of trying to localize the particle within a certain region
of space. Since the zero point energy is a base level and can't be reduced, you can't use zero point
energy to do anything useful. It's just there.

It's just 'there'....and it CAN be used BECAUSE

it is a wave, waves can be intercepted and
RECTIFIED, Nature does it and one day, in the very near future, we too will learn to utilize this
enormous energy source.

Peter Lindemann wrote on the differences between aether and electricity for Borderlands.

As of June 16th and 17th at the KeelyNet Convergence 2001 conference in Dallas, many of us,
including Peter Lindemann, feel major strides have been made in our collective understandings
about how to tap into the aether/zpe energies which could well lead to a self-sustaining overunity
device which might be capable of powering a small load in the near future.

You should seriously consider investing in two items, one is the book and/or video produced by
Lindemann, the other is the book by Gerry Vassilatos, Secrets of Cold War Technology, click on
'new books from AUP'. At this conference, several key principles were presented and discussed;

• 1 - unidirectional discharges without any reflected energy as EV Gray

achieved with his power conversion tube based on Teslas move from AC to
high intensity, short duration pulse DC to produce phenomena - Gray
referred to it as 'splitting the positive' which we understand to mean never
letting the unidirectional arc discharge be allowed to strike zero which
would cause a back reflection, instead the power conversion tube uses a
carbon block on the receiving lower potential side of the arc which slows
the discharge down to +12vdc, thus 'squeezing' or 'splattering' the
entrained aether/zpe into the copper mesh as shown in John Bedini's Power
Conversion Tube
• 2 - Bill Mullers use of 'river sand' magnetite mixed with a fixing agent to
produce a variable reluctance core which responds instantly to changes in
magnetic flux polarity
• 3 - a unique zero resistance core design where an increase in the current
required by the load results in no resistance to the magnet motion past the
coil core, the design for a normal solenoidal coil has the wire wound from
top to bottom and as the magnet passes the coil, the resistance to its passage
increases as the load current requirements increase (remember the old
army hand cranked telephone field generator - the more load you hook to
it, the harder it is to turn the handle), this new design has a core where the
winding begins roughly 1/3 to 1/2 down the length of the core and the
windings increase in turns as it approaches the bottom of the core, taking
the form of a cone with the apex pointing up, this is quite similar to the
HomoPolar motor which does not experience any resistance no matter how
much current is extracted by the load devices.
• 4 - aether/zpe entrainment as described earlier in this paper

• 5 - using bifilar windings and pulses to increase efficiency and even to produce overunity
as Doug Konzen appears to be getting and who some of us feel is a key player in the search for a
working, FREELY SHARED overunity device. We have high hopes for Doug and he is an
inspiration to others, check out his website.

You can follow up on much of this and keep track as new details come in by going to
the KeelyNet Interact Discussion List which is publicly archived and available for viewing as
well as the What's New page.

I also want to add the important observation made by Gerald Orlowski based on the work of
Rory Johnson that magnetism attracts to itself as opposed to electricity which repels itself.

"...Faraday had a great teaching on this subject, he stated, "When a current suddenly ceases, it
can INDUCE a current IN THE SAME WIRE which is stronger than the original current. Thus,
by conservation of force, there must be some force present, AN OPERATIVE, other than
electric force. This force is probably the MAGNETIC FORCE." Science had this enlightening
teaching over 150 years ago! Unbelievable!..."

So what is different between these two energy FORMS? As we know, electrical flow argues, that
is, it sparks, short circuits, and must be CAREFULLY insulated, Magnetic structures, rather,
want to SHARE their flow, and are compatible to the Universal Force. This new energy FORM
responds when it is needed as well as HOW it is needed, manifesting as a MEASURABLE
current.
Thus, in defining these different energies, it is important to understand that although electrical
and magnetic (energy) work with similar ATTITUDES, the MANNER in which they work, sets
up a differing energy effect. THINK MAGNETIC THINK MAGNETIC

• there was a material and/or a shape that would intercept the energies
produced by this randomly appearing 'noise' of the quantum foam?
• this material and/or shape, depending on its ability to interact with this
quantum noise, could be used to produce either a mechanical force or an
electric current?
• this material and/or shape had the ability to absorb and redirect the
random and chaotic appearances of this quantum foam so that it would
effectively have one side that was polarized as a receptor, the other side as
an emitter, where the emitter would radiate a repelling force or conduct an
electric current?
• this material exists everywhere but is so diffuse and randomly directed as
to cancel out its weak abilities?

By using the above described material/shape so that when polarized, it would function as a check
valve to produce either a mechanical pressure or as a diode for electrical current, we could
collimate and channel ambient energy flows from these random quantum foam appearances into
a preferred direction.

The collimation of the random aether/zpe radiations will produce either mechanical thrust or
electricity, depending on the properties of the material/shape used and based on a long
proposed 'Aether/ZPE Spectrum'.

The idea being that aether/zpe consists of a band of frequencies far higher than anything we can
measure, since it suffuses, permeates, creates and sustains all matter and energy.

When these high frequency aether/zpe waves are slowed down and extended they produce
magnetism. When magnetism is slowed and extended, it produces electricity, then light, heat,
sound, physical vibration and matter. The reverse effect is E=MC^ where matter is dissociated
on a nuclear level to yield tremendous energies as it returns up the spectrum to aether/zpe.

Each of these gradations has its own spectrum just as each color can be subdivided for many
shades.

Reload/Refresh this page now please to update graphics that follow

Quantum Foam illustrations of Aether/ZPE

 The background noise of Aether/ZPE popping in and out of
existence, suffuses all matter and space, in sufficient density
near mass to produce the ubiquitous effect we call 'gravity'.

The Aether/ZPE noise magnified to show clusters of primary

points that can be further enlarged to show their structure.

The noise clusters magnified to show as 'primary points' and

whose energy radiates in all directions from each central point
as it explodes into being.

In a way, Aether/ZPE is akin to the random movements of Brownian motion and to the
NEGentropic heat collection of Maxwells Demon.

The Standing
Wave of Matter
It is the flow of this aether/zpe as one or more
frequencies into matter, where it is REFLECTED
FROM THE CENTER to phase conjugate with
incoming aether/zpe as shown in this standing wave
animation.

For our purposes, we are seeking to allow the passage of the random chaos of the aether/zpe
radiations through our check valves or diodes.

Since this 'theoretical' material or shape would function like a check valve to produce
mechanical thrust or a diode to rectify the aether/zpe down to an electric current;

then one such unit would produce a tiny amount of thrust or current;

whereas many such check valves - all oriented in one direction, subject to a wider exposure of
aether/zpe and over a small surface area,
would produce a combined emitter pushing effect that could be made to emanate in any
preferred direction, to provide lift or thrust or, as noted earlier with the right material/shape to
produce an electric current.

It would function like a 'natural' pump which, when placed in a balanced medium and turned
on, will draw in the polarized, rectified, randomized ambient medium in one end and push it out
the other side of the pump as a collimated force.

Think of a car moving at 60 mph. When it stops, you are pushed against the steering wheel, with
the accepted 'understanding' being that this is caused by 'inertia'.

Some today view this as the entrained viscosity of the background aether/zpe when it is
disturbed as matter moves through the medium. The more rapidly the mass accelerates, the
greater will be the disturbance.
If you sit on a motorcycle, gun the engine to high rpms and pop the clutch, you will be left on the
ground as the accelerating motorcycle breaks away from you. Pushed back by the 'dilatant
matrix' of the aether. The rapid acceleration and associated stresses on all the connected pieces
of that motorcycle do not transfer to you when simply sitting unattached to the seat.

As of 03/20/00, a recent update came to my attention of a superb chart of Zero Point Energy
Effects on Mass (as mirrored below), constructed by Robert E. Brady with his website that
describes three types of gravity theories.
If we create a well or hole in the zpe, then mass will 'fall' or rather BE PUSHED into
that hole. As written up elsewhere on KeelyNet, a German researcher named
Zielinski claims his private group has this figured out though he won't give any
details. We were able to get him to admit it used high voltage.
He said the mass to be moved would have something like a 100 pound weight placed
in the front of it, the gravity well is created just ahead of this weight and the 100
pound weight along with the weight of the mass is pushed in that direction. By
adjusting the location of the well, you can make it move in any desired direction.
Thinking along those lines, the chaos converter could simply be an aether/zpe
ABSORBER, where the polarized side FACING UP would cause the mass attached to
them to FALL or BE PUSHED upward! Kind of like a pump, creating a suction and
if its strong enough, it would start 'sucking air' because it would suck faster than the
ambient/zpe could flow in to fill it up. So it absorbs more on one side than on another.
Also elsewhere on KeelyNet are the comments by the high priest in charge of the Ark
of the Covenant, claiming that the giant stone obelisks in Ethiopia were lifted into
place using the 'celestial fire' that came from the Ark.

As well as the Dendera photos from 1,000 BC in the crypt at the Temple of Hathor,
showing men holding what appear to be 5 foot long, 1 foot wide, tapered glass tubes
with a snake in each, connected by a braided cable to a djet capacitor stack.
No one KNOWS what this was for but most of what I've seen points to the probability
of creating a plasma vortex or a successive stream of high intensity, short duration
discharges through the tube, that would entrain aether/zpe into a collimated beam
directed at mass to cause it to absorb, radiate and repel surrounding aether/zpe, thus
losing weight.

As of 03/31/00, additional information that correlates perfectly with this file can be
found in the U.S. Patent 5,590,031 by Mead on Dec. 31, 1996.
Excerpts from the patent;
The invention relates generally to conversion of electromagnetic radiation energy to
electrical energy, and, more particularly, to conversion of high frequency bandwidths
of the spectrum of a type of radiation known as zero point electromagnetic radiation
to electrical energy.
The existence of zero point electromagnetic radiation was discovered in 1958 by the
Dutch physicist M. J. Sparnaay. Mr. Sparnaay continued the experiments carried out
by Hendrik B. G. Casimir in 1948 which showed the existence of a force between two
uncharged parallel plates which arose from electromagnetic radiation surrounding
the plates in a vacuum.
Mr. Sparnaay discovered that the forces acting on the plates arose from not only
thermal radiation but also from another type of radiation now known as classical
electromagnetic zero point radiation. Mr. Sparnaay determined that not only did the
zero point electromagnetic radiation exist in a vacuum but also that it persisted even
at a temperature of absolute zero.
Because it exists in a vacuum, zero point radiation is homogeneous and isotropic as
well as ubiquitous. In addition, since zero point radiation is also invariant with
respect to Lorentz transformation, the zero point radiation spectrum has the
characteristic that the intensity of the radiation at any frequency is proportional to
the cube of that frequency. Consequently, the intensity of the radiation increases
without limit as the frequency increases resulting in an infinite energy density for the
radiation spectrum.
With the introduction of the zero point radiation into the classical electron theory, a
vacuum at a temperature of absolute zero is no longer considered empty of all
electromagnetic fields. Instead, the vacuum is now considered as filled with randomly
fluctuating fields having the zero point radiation spectrum.
The special characteristics of the zero point radiation which are that it has a virtually
infinite energy density and that it is ubiquitous (even present in outer space) make it
very desirable as an energy source.
However, because high energy densities exist at very high radiation frequencies and
because conventional methods are only able to convert or extract energy effectively or
efficiently only at lower frequencies at which zero point radiation has relatively low
energy densities, effectively tapping this energy source has been believed to be
unavailable using conventional techniques for converting electromagnetic energy to
electrical or other forms of easily useable energy.
Consequently, zero point electromagnetic radiation energy which may potentially be
used to power interplanetary craft as well as provide for society's other needs has
remained unharnessed.
What is therefore needed is a system which is capable of converting high frequency
electromagnetic radiation energy into another form of energy which can be more
readily used to provide power for transportation, heating, cooling as well as various
other needs of society. What is also needed is such a system which may be used to
provide energy from any location on earth or in space.
Essentially, the system of the present invention utilizes a pair of structures for
receiving incident electromagnetic radiation which may be propagating through a
vacuum or any other medium in which the receiving structures may be suitably
located. The system of the present invention is specifically designed to convert the
energy of zero point electromagnetic radiation; however, it may also be used to
convert the energy of other types of electromagnetic radiation. The receiving
structures are preferably composed of dielectric material in order to diffract and
scatter the incident electromagnetic radiation.
In addition, the receiving structures are of a volumetric size selected to enable the
structures to resonate at a high frequency of the incident electromagnetic radiation
based on the parameters of frequency of the incident radiation and propagation
characteristics of the medium and of the receiving structures.
Since zero point radiation has the characteristic that its energy density increases as its
frequency increases, greater amounts of electromagnetic energy are available at
higher frequencies. Consequently, the size of the structures are preferably
miniaturized in order to produce greater amounts of energy from a system located
within a space or area of a given size.
In this regard, the smaller the size of the receiving structures, the greater the amount
of energy that can be produced by the system of the present invention.
At resonance, electromagnetically induced material deformations of the receiving
structures produce secondary fields of electromagnetic energy therefrom which may
have evanescent energy densities several times that of the incident radiation.
The structures are of different sizes so that the secondary fields arising therefrom are
of different frequencies. The difference in volumetric size is very small so that
interference between the two emitted radiation fields, and the receiving structures at
the two different frequencies produces a beat frequency radiation which has a much
lower frequency than the incident radiation.
The beat frequency radiation preferably is at a frequency which is sufficiently low
that it may be relatively easily converted to useable electrical energy. In contrast, the
incident zero point radiation has its desirable high energy densities at frequencies
which are so high that conventional systems for converting the radiation to electrical
energy either cannot effectively or efficiently so convert the radiation energy or
simply cannot be used to convert the radiation energy for other reasons.
The system of the present invention also includes an antenna which receives the beat
frequency radiation. The antenna may be a conventional metallic antenna such as a
loop or dipole type of antenna or a rf cavity structure which partially encloses the
receiving structures.
The antenna feeds the radiation energy to an electrical conductor (in the case of a
conventional dipole or comparable type of antenna) or to a waveguide (in the case of a
rf cavity structure). The conductor or waveguide feeds the electrical current (in the
case of the electrical conductor) or the electromagnetic radiation (in the case of the
waveguide) to a converter which converts the received energy to useful electrical
energy.
The converter preferably includes a tuning circuit or comparable device so that it can
effectively receive the beat frequency radiation. The converter may include a
transformer to convert the energy to electrical current having a desired voltage. In
addition, the converter may also include a rectifier to convert the energy to electrical
current having a desired waveform.
ZPE appears across a broad spectrum of frequencies and one of the interesting
comments in the patent is on page 13;

"Since, as set forth hereinabove, the energy density of the zero point radiation
increases as the frequency of the radiation increases, it is desirable that the spheres
resonate in as high a bandwidth of frequencies as possible. Because the spheres 212
and 214 must be small in direct proportion to the wavelength of the high frequencies
of the incident electromagnetic radiation 216 at which resonance is desirably
obtained, the spheres 212 and 214 are preferably MICROSCOPIC in size.
Current lithographic techniques are capable of manufacturing such microscopically
small spheres mounted on a suitable substrate thereby providing a suitably
miniaturized system 210.
A miniaturized system enhances the energy output capability of the system by
enabling it to resonate at higher frequencies at which there are correspondingly
higher energy densities. Consequently, utilization of array 238 in the system 210
enhances the maximum amount of electrical energy provided by the system 210."
Lithographic techniques may be more amenable to manufacturing microscopically
small receiving structures 212 and 214 which may be disc shaped, semispherical or
have another shape other than as shown in FIGS. 4 and 5. Consequently, the
receiving means 212 and 214 may accordingly have such alternative shapes rather
than the spherical shape shown in FIGS. 4 and 5. In addition, a large number of small
spheres may be manufactured by bulk chemical reactions. Packing a volume with
such spheres in close proximity could enhance the output of energy.
Embodiment 210 also includes a plurality of antennas 222 positioned preferably
between the spheres 212 and 214 which receive the beat frequency radiation 224
produced by the interference between the secondary radiation 218 and 220. The
antennas 222 are shown as loop antennas 222 but may be any other suitable type of
antennas as well.
Embodiment 210 has a plurality of electrical conductors 226 which preferably include
traces mounted on the substrate 236 which occupies a finite volume. The electrical
conductors 226 feed the electrical output from the antennas 222 to a suitable
converter 228 which preferably includes tuning capacitor 230, transformer 232 and
rectifier 234, as with embodiments 10 and 110.

Therefore, the interception of local ZPE can be so designed as to be redirected to

produce a repellent force, to produce a 'hole in space' in which mass would 'fall' OR
can be interferred with to generate an 'electromagnetic beat frequency' that will
induce electrical current for power.

In a more outrageous vein, in legends and myths, we read about flying animals such as
Bellerophons' flying horse Pegasus and references to other winged creatures such as gryphons,
giant Roc birds, and other fantastic things whose
weight to wingspread area don't make sense.

We also are told through legend and myth about the

witches flying broom and the flying carpet of
ancient Persia.
What if the ancients discovered this natural shape and/or material which by itself had an almost
imperceptible effect, yet in accumulation, could redirect the chaos of the ambient aether/zpe into
a specific direction to produce a useful effect such as a cancellation of 'gravity' and even a thrust
in a preferred direction?

The carpet could also be kept

earthbound by laying it on the
floor or ground with the
polarized side facing outward in
all directions, thus losing any
lifting abilities due to smaller
surface area and dispersion of
the effect.

Since this ambient aether/zpe

originated chaotic energy, which
appears and disappears to
saturate all local mass, would be intercepting, collimating and redirecting these ambient chaotic
natural energies, no power would have been required in the form of electricity, magnetism or
human physical effort.

Thus they had no recourse for understanding the true cause, having to resort to magic and the
claim that jinn, demons or some other 'supernatural' force was the lifting and propelling agent.

If such a material having this aether/zpe chaos converter effect were to be woven into a carpet
with the right polarization, so that the effect emanated from one side of the carpet, then it could
well be that flying carpets were possible by those who studied and understood such matters.

As of 04/06/00, a fascinating piece of information

came in that ties in perfectly with this document
which I've been working on since around October
99' now. As you can see it relies on a moving
Casimir junction to produce mechanical thrust. It
involves a new $300,000 research project
sponsored by NASA and refers to a vacuum
fluctuation tap which occurs on microscopic levels
as proposed in this document.