Scribd
Upload
106 views1 page

4CS3-04 - II Paper

This document is an exam for a microprocessor and interfaces course. It contains 3 parts with multiple choice questions about microprocessor components like the 8255, 8254, and 8279 ICs. The questions test understanding of topics like control word formats, timer setup, block diagrams, and interfaces. The exam focuses on applying knowledge of microprocessors, peripherals, and interfacing components.

Uploaded by

Abhishek Dadhich
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
106 views1 page

4CS3-04 - II Paper

This document is an exam for a microprocessor and interfaces course. It contains 3 parts with multiple choice questions about microprocessor components like the 8255, 8254, and 8279 ICs. The questions test understanding of topics like control word formats, timer setup, block diagrams, and interfaces. The exam focuses on applying knowledge of microprocessors, peripherals, and interfacing components.

Uploaded by

Abhishek Dadhich
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 1

POORNIMA INSTITUTE OF ENGINEERING & TECHNOLOGY, JAIPUR

II B.TECH. (IV Sem.) Roll No. __________________


SECOND MID TERM EXAMINATION 2019-20
Code: 4CS3-04 Category: ESC Subject Name–MICROPROCESSOR & INTERFACES
(BRANCH – COMPUTER ENGINEERING)
Max. Time: 2 hrs. Max. Marks: 60
NOTE:- Read the guidelines given with each part carefully.

PART - A: (All questions are compulsory) Max. Marks (10)


Q.1 Draw the control word format of BSR mode for 8255 IC. (2)(CO4)
Q.2 Calculate the value of COUNT if we want to generate 1KHz Square wave with the (2)(CO4)
help of 8254 IC. Assume system clock frequency is 2 MHz

Q.3 What is the significance of Read Back command? (2)(CO4)


Q.4 Draw the pin configuration of LCD (2)(CO5)
Q.5 Write any four important things that one should keep in the mind while designing the (2)(CO5)
microprocessor unit
PART - B: (Attempt 4 questions out of 6) Max. Marks (20)
Q.6 Draw the block diagram of 8255 IC and also explain it. (5)(CO4)
Q.7 Write a BSR control word subroutine to set bits PC7 and PC3 and reset them after (5)(CO4)
10ms. Assume that a delay subroutine is available.
Q.8 Explain the block diagram of 8254 IC. (5)(CO4)
Q.9 Discuss about Centronics parallel interface. (5)(CO5)
Q.10 Explain different microprocessor applications in brief. (5)(CO5)
Q.11 Explain working methodology of matrix keyboard. (5)(CO5)

PART - C: (Attempt 3 questions out of 4) Max. Marks (30)


Q.12 (a) Specify the conditions to start the timer 8254 and setup 8254 as a square wave (5)(CO4)
generator with a 1 ms time period, if the input frequency is 2 MHz
Q.12 (b) Discuss the block diagram of 8279 IC briefly. (5)(CO4)

Q.13 Draw the pin diagram of 8254 IC. Also explain all the operating modes of 8254 along (10)(CO4)
with the suitable waveforms.
Q.14 (a) Discuss about the significance of USART 8251. Also draw its block diagram. (5)(CO5)

Q.14 (b) Explain IEEE-488 parallel interface with a suitable diagram (5)(CO5)
Q.15 Write a short note on: (10)(CO5)
(i) RS232C and RS422A
(ii) 8085 MPU Design
-----

Page 1 of 1

You might also like