Oil & Gas /

Heavy Industry

Type 2REX-A
· EX d-Proof Shaft Encoder - Ø 68
· Shaft Ø 10 mm to ø5/8”
· Resolution up to 10,000 ppr
· IP 66 (IP 64, 65, 67 option)
· “Seawater-proof “ 22 micron Anodization
· ATEX certified EX-Proof
IECEx certified EX-Proof
EN 60079

Electrical Specifications Mechanical Specifications

Code: Incremental Housing: Aluminum
1 to 10,000 ppr (pulses per Material: Cap: Aluminum
Resolution: Shaft: Stainless Steel (AISI 303)
revolution)
4.5 Vdc min. to 30 Vdc max. ** Encoder: Approx. 540 gr (19 oz)
Supply Voltage: Weight:
(45 mA max. - no load) Cable: 50 gr / meter (1.76 oz / meter)
Low: 500 mV max. at 10 mA Bearing Life: > 1.9 x 1010 revolutions at rated load
Output Voltage: High: (Vin – 0.6) at -10 mA Shaft Speed: 3,000 rpm continuous (max.) IP 67 T5
(Vin – 1.3) at -25 mA
30 mA max. load ** Starting Torque: < 0.1 Nm (14.16 oz-in) at 25° C IP 67
Output Current:
per output channel Mass Moment of
50 gcm² (7.08 x 10-4 oz-in-sec²)
Frequency Response: 300 kHz max. ** Inertia:
Two channel (A, B) quadrature with Axial 50 N (11.25 lbs) max.
Shaft Loads:
Output Format: Index (Z) and optional Radial 100 N (22.50 lbs) max.
complementary (A-, B-, Z-) outputs
A leads B clockwise (CW) from the
Phase Sense:
mounting end of the encoder
Index: Gated with Channels A and B high Environmental Specifications
Accuracy: +/- 0.8 arc-min. Operating Temp.: -40° to +70° C
ASIC Push-pull and Differential Storage Temp.: -40° to +85° C
OL7272 Differential Line Driver Shock: 100 G / 11 ms
Outputs: (M and MP options) Vibration: 10-2000 Hz / 10 G
26C31 Differential Line Driver Bump: 10 G / 16 ms (1000 x 3 axis)
5V output (with 5V input)
Humidity: 98 % RH without condensation
Output short circuit protected
IP 64 / Nema 4 (approx.) option
Electrical Protection: Reverse polarity protected (ASIC
IP 65 / Nema 4 (approx.) option
and MP (OL7272) outputs only) Enclosure Rating:
IP 66 / Nema 6 (approx.)
IP 67 / Nema 6 (approx.) option
Tested to EN61000-6-2 : 2005
(industrial environments)
Electromagnetic compatibility (EMC) Connection Options
Noise Immunity: and EN 61000-6-3 : 2007 (residential, 8 leads (0.14 mm2, 26 AWG) twisted pairs;
commercial, and light-industrial Cable:
shielded; halogen free
environments) for Electromagnetic
compatibility (EMC) 9-position terminal block (inside cap)
Cable Glands:
M20 cable gland (fits cable Ø 11 – 14.5 mm)
**= It is recommended user not to combine max. Value for all 3 parameters

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 1
Tlf +45 48 17 27 02 www.scancon.dk
 Type 2REX-A

Certifications
Certificate No.: ITS09ATEX16847X
ATEX:
II 2 G Ex db IIC T5 II 2 D Ex tb IIIC T100°C Db -40°C < Tamb < +70°C
Certificate No.: IECEx ITS 10.0015X
IECEx:
Ex db IIC T5 Gb Ex tb IIIC T100°C Db -40°C < Tamb < +70°C
НАНИО «ЦСВЭ» No. ЕАЭС RU C-DK.AA87.B.00266/19
EAC Ex:
1Ex db IIC T5 Gb X, Ex tb IIIC T100°C Db X, -40°C<T.amb<+70°C

Output waveform Disk Resolutions (pluses per revolution)

1 32 125 720 3000

2 36 150 800 3072
5 40 180 1000 3600
6 45 200 1000 4000
7 47 250 1024 4096
8 50 256 1131 5000
10 60 300 1200 8192
12 64 360 1250 9000*
15 70 400 1270 10000
16 75 455 1500
18 80 500 2000
20 90 512 2048
Channel tolerance 180 e° +/- 36 e°
Phase difference tolerance 90 e° +/- 18 e° 25 100 600 2400
Z channel tolerance 90 e° +/- 18 e°
30 120 635 2500

Other options on request

Pulses per revolution,
min. 1 – max. 10.000

* Operating temperature: -20° C to 50° C

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 2
Tlf +45 48 17 27 02 www.scancon.dk
 Type 2REX-A

Mechanical Dimensions

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 3
Tlf +45 48 17 27 02 www.scancon.dk
 Type 2REX-A

Measurements: mm (inches)

Encoder Length
Total length of encoder L = Lb + Lf

Body
Flange Standard Standard Standard End Cap
Type Side - (SS) Back - (BS) SH08 (EC01)
A 61,5 (2,42) 60,0 (2,36) 62,5 (2,46) 75,0 (2,95)
K 73,5 (2,89) 72,0 (2,83) 74,5 (2,93) 87,0 (3,43)

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 4
Tlf +45 48 17 27 02 www.scancon.dk
 Type 2REX-A
Output Terminations

Removable End Cap

Terminal Block
Standard Differential
Output Output
Position Channel Channel
1 * Z-
2 Z Z
3 * B-
4 B B
5 * A-
6 A A
7 Vsup Vsup
1 2 3 4 5 6 7 8 9
8 GND GND
9 Shield Shield

* Do not attach any wires to terminal block Z- Z B- B A- A Vsup GND Shield

GND = Circuit Ground Shield = Case Ground

Standard Cable
Standard Differential
Output Output

Channel Wire Color Wire Color

A Pink Pink
A- Gray* Gray
B Green Green
B- Yellow* Yellow
Z White White
Z- Brown* Brown
Vsup Red Red
GND Blue Blue

* Gray, Yellow, and Brown are internally connected to Circuit Ground

GND = Circuit Ground

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 5
Tlf +45 48 17 27 02 www.scancon.dk
 Type 2REX-A
Ordering Code

Example: 2REX-A – 1024 – AL – D – 10 – 20 – 67 – 01 – SS – A – 00

2REX-A - - AL - - - - - - - - 00
Pulses per Material Output Shaft Shaft IP Cable Cable Flange Accessory
Revolution Dia. Length Rating Length Takeout
See table

IP 64 64 A A
IP 65 65 K K

Aluminium AL IP 66 66
IP 67 67

Standard N
Standard is 1 meter 01 None 00
Standard –open Collector NPN NON
Specify length XX
Standard –open Collector NOP NOP No Cable (End Cap) 00
Differential D
26C31 Line Driver 5V only L Side (Standard) SS
OL 7272 Line Driver M Back (Standard) BS
End Cap (M20 x 1.5 cable gland) EC01
Side (1 - 1/6” – 12 UNF) SH08
*Cable Glands may be ordered as separate

10 mm x 20 mm (Flanges A, K) 10 - 20
10 mm x 27 mm (Flange A) 10 - 27
10 mm x 30 mm (Flange A) 10 - 30
5/8 inch x 20 mm (Flange A) 5/8 - 20
11 mm x 27 mm (Flange A) 11 - 27

Other options on request:

Please contact Scancon A/S

Rev. 3.2 10. Feb. 2020 Scancon Encoders A/S Huginsvej 8 3400 Hilleroed Denmark p. 6
Tlf +45 48 17 27 02 www.scancon.dk