Scribd
Upload
241 views2 pages

Flywheel New PDF

1. The document describes an experiment to determine the moment of inertia of a flywheel about its axis of rotation. A mass is attached to the flywheel with string and allowed to fall, causing the flywheel to oscillate. 2. The number of oscillations and time taken for the flywheel to stop are recorded for different masses. 3. The moment of inertia is then calculated using the formula derived from the experiment and checked against the theoretical value to determine accuracy.

Uploaded by

Elizebeth
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
241 views2 pages

Flywheel New PDF

1. The document describes an experiment to determine the moment of inertia of a flywheel about its axis of rotation. A mass is attached to the flywheel with string and allowed to fall, causing the flywheel to oscillate. 2. The number of oscillations and time taken for the flywheel to stop are recorded for different masses. 3. The moment of inertia is then calculated using the formula derived from the experiment and checked against the theoretical value to determine accuracy.

Uploaded by

Elizebeth
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Moment of inertia of a Flywheel

OBJECT: To determine the moment of inertia of a flywheel about its own axis of rotation.
Apparatus used: Flywheel, a few masses, a strong and thin string, stop watch, vernier callipers.
Formula used: The moment of inertia of a flywheel is given by following formula:
2mgh
2 2 − mr 2
2mgh − mr ω 2
I= = ω
⎛ n ⎞ ⎛ n ⎞
ω 2 ⎜⎜1 + 1 ⎟⎟ ⎜⎜1 + 1 ⎟⎟
⎝ n2 ⎠ ⎝ n2 ⎠
2 π n2
Since ω = 2 × and h = 2π r n1
t
2mg( 2π r n1 ) t 2
− mr 2

y
2
( 4 π n2 )
I=
⎛ n ⎞

de
⎜⎜1 + 1 ⎟⎟
⎝ n2 ⎠
⎛ gt 2 n ⎞
mr ⎜ 1 −r⎟
⎜ 4 πn 2 ⎟
I= ⎝ ⎠
an
2
⎛ n1 ⎞
⎜⎜1 + ⎟⎟
⎝ n2 ⎠
gt 2 n1
Since >> r
.P

4 πn22
⎛ n ⎞
mrgt 2 n1 ⎜⎜1 + 2 ⎟⎟
m g r t2
I= = tan θ1 = = ⎝
1 n1 ⎠ = AB
2 ⎛⎜ n1 ⎞ ⎛ n ⎞
.K

4 πn2 ⎜1 + ⎟⎟ 4 π n2 ⎜⎜1 + 2 ⎟⎟ K m BC
⎝ n2 ⎠ ⎝ n1 ⎠
gr m t2 gr
I= = KC
4 π ⎛ n2 ⎞ n2 4 π
D

⎜⎜1 + ⎟⎟
⎝ n1 ⎠
⎛ n ⎞
Where K = m ⎜⎜1 + 2 ⎟⎟ ; C = t 2 n2 ;
⎝ n1 ⎠

g = gravitational acceleration.
r = radius of flywheel axis.
m = mass suspended through string / thread.
n1 = Number of turns of string wrapped on axis. t2 PQ
n2 = Number of oscillation up to flywheel stopped tan θ 2 = C = =
n2 QR
after detaching the mass.
t = time of oscillation up to flywheel stopped after
detaching the mass.
Procedure:
1. Measure the diameter of the axle with vernier calipers at different points and find the mean.
2. Attach the mass with string.
3. Wrap the string or thread axle of flywheel for allotted number of turns (n1=4 or 6 or 8).
4. Allow to fall the mass.
5. After fall of the mass, note the number of oscillation of flywheel (n2) and corresponding time
(t2) till the flywheel stopped.
6. Repeat procedure from 2-5 at fixed n1 for different masses (e.g. m=100, 150, 200, 250, 300gm)
n
7. Draw the graphs between mass (m) and (1+ 2 ) and between n2 and t 2 . The graph should be
n1
separate for each n1.
Observation:
A. For radius of axle
value of one division on main scale
Least count of vernier callipers = = .........cm

y
Number of division on vernier scale
Sr. No. Main scale reading Vernier scale reading Total

de
1
2
3
4
5
an
Diameter of axle (D=Mean of Total = ……………………………………
Radius of axle ( r=D/2 ) = …………………………………………………
B. For n2 and t
n
1+ 2 t2
.P

Sr. no. n1 m n2 t
n1
1
2
.K

3
4
5
Calculation:
D

The moment of inertia can be calculated with following formula:


gr g r tan θ 2
I= KC=
4π 4 π tan θ1
Δ I ⎧Δ r Δt⎫ ΔI ⎧Δ r Δt⎫
Least count error: =⎨ +2 ⎬ ⇒ x100 = ⎨ + 2 ⎬ x100
I ⎩ r t ⎭ I ⎩ r t ⎭
Result:
The moment of inertia of fly wheel is …………….. ± …………..(unit).
Precautions:
1. There should be least friction in flywheel.
2. The length of string should be less than the height of axle from floor.
3. There should be no kink in string.
4. The string should be thin and should be wound evenly.
5. The stop watch should be started just after detaching the loaded string.

You might also like