7 6 5 4 3 2 1

ARCH E 36"x48"
3" MAXIMUM
PROVIDE 1/4" SEAL CAP PLATE AT TYPICAL
SHIM AS REQUIRED TO
TOP OF COLUMN, USE THIS DETAIL
MAINTAIN BAY LENGTH
FOR NON-LOADBEARING
DIMENSION
CONDITIONS AT TOP OF COLUMN

CONTINUOUS HIGH CHAIRS SINGLE PLATE

FLEXURAL
REFER TO NOTE 4 REINFORCEMENT FOR STEEL DECK (CRSI TYPE
CHCM) @ 48" MAXIMUM

CLEAR COVER
CLEAR COVER

CLEAR COVER
TEMPERATURE SLAB REINFORCEMENT
REINFORCEMENT ADDITIONAL #4x8'-0"@12" A A
STEEL BEAM OPENING SCHEDULE CENTERED OVER GIRDERS
DOUBLE ANGLE 4'-0" MAXIMUM 4'-0" MAXIMUM 6" MINIMUM 6" MINIMUM
OPENING PLATE PLATE
WELD A
PLATE PLATE
WELD B
PROJECT
MARK SIZE "A" "A" "B" "B"
SIZE SIZE SNUG-TIGHTENED BOLTED
F WxD B x La x t Fy B x Lb x t Fy CONNECTION WITH STANDARD
HOLES, TYPICAL, RESISTANCE BY NEW ORLEANS ARENA
1 24 x 12 6 x 42 x 3/4 50 3/8 6 x 13 x 1/2 36 1/4 BOLTS TO SHEAR LOAD SHALL BE ENHANCEMENTS 2012
BY SHEAR/BEARING
ARENA RENOVATION & EXPANSION

CLEAR COVER
2 12 x 12 5 x 24 x 1/2 36 3/8 5 x 13 x 3/8 36 1/4 LSED # NOA-ENH-2012-AFC35.4M
CONTINUOUS SLAB BOLSTERS STEEL DECK CONTINUOUS HIGH CHAIRS STEEL DECK STEEL DECK
(CRSI TYPE SB) @ 48" MAXIMUM FOR STEEL DECK (CRSI TYPE New Orleans Arena
3 16 x 8 4 x 32 x 1/2 36 1/4 4 x 9 x 1/4 36 1/4 TO SUPPORT TEMPERATURE CHCM) AT EACH GIRDER AND
SNUG-TIGHTENED BOLTED CONNECTION 1501 Girod Street
WITH STANDARD HOLES, RESISTANCE REINFORCEMENT @ 48" MAXIMUM
BY BOLTS TO SHEAR LOAD SHALL BE BY 4 12 x 6 4 x 26 x 3/8 36 1/4 4 x 7 x 1/4 36 3/16 New Orleans, LA 70113
SHEAR/BEARING INDIVIDUAL BAR CHAIRS (CRSI TYPE BC)
@ 48" MAXIMUM TO SUPPORT FLEXURAL CLIENT
REINFORCEMENT
NOTES: LOUISIANA STADIUM AND
1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. NOTE 3
STEEL GIRDER STEEL GIRDER STEEL GIRDER EXPOSITION DISTRICT
2. REFER TO PLAN FOR CONNECTION DESIGN REACTIONS.
3. PROVIDE PREDESIGNED CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF STEEL SECTION A-A 1500 Girod Street
CONSTRUCTION MANUAL WHERE APPLICABLE. New Orleans, LA 70112
4. SHOP WELD ON 3 SIDES TO DEVELOP BEAM REACTION, TYPICAL. NOTES: NOTES:
5. WT CAN BE SUBSTITUTED FOR DOUBLE ANGLES. 1. REINFORCEMENT SHOWN OVER GIRDERS IS IN ADDITION TO THE 1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA.
TYPICAL SLAB REINFORCEMENT SPECIFIED ON THE DRAWINGS 2. REFER TO PLAN FOR CONNECTION DESIGN REACTIONS. ARCHITECTS
3. MINIMUM FILLET WELD SIZE SHALL BE 5/8 TIMES THE PLATE THICKNESS.
AECOM LOUISIANA, A PROFESSIONAL
CORPORATION
TYPICAL SHEAR CONNECTION TYPICAL REINFORCEMENT PLACEMENT TYPICAL REINFORCEMENT PLACEMENT TYPICAL ADDITIONAL REINFORCEMENT IN TYPICAL SHEAR CONNECTION 2380 McGee Suite 200
AT COLUMN FLANGE SEE PLAN FOR COMPOSITE SLABS FOR COMPOSITE SLABS COMPOSITE SLABS AT INTERIOR GIRDERS AT RECTANGULAR/SQUARE HSS COLUMN Kansas City, Missouri 64108

6 NO SCALE 05120-CN-BMCOL-37
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
CL OPENING 4 NO SCALE 03200-FL-RSPT-05
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
3 NO SCALE 03200-FL-RSPT-06
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
2 NO SCALE 03200-FL-RSPT-08
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
1 NO SCALE 05120-CN-BMCOL-22A
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2012
816.561.4443 tel
www.aecom.com
816.561.2863 fax

WELD WELD
B
La
A ESKEW+DUMEZ+RIPPLE
EQ W EQ NOTES: 365 Canal Street Suite 3150
1. WHERE CLEAR SPACING BETWEEN ADJACENT SLEEVES IS LESS THAN 3", THE SLEEVE New Orleans, LA 70130
E 504.561.8686 tel 504.522.2253 fax
GROUP SHALL BE TREATED AS AN EQUIVALENT RECTANGULAR OPENING WITH LENGTH "L"
CL COLUMN AND WIDTH "W" AS SHOWN. www.eskewdumezripple.com

TYP
1/2"
EQ
2. WHERE CLEAR SPACING BETWEEN ADJACENT SLEEVES IS GREATER THAN OR EQUAL TO 3",
PL TO MATCH BEAM
FLANGE +1/8", TYPICAL
SCHEDULED SLAB BAR REINFORCEMENT SHALL BE OFFSET AS REQUIRED TO MISS MANNING ARCHITECTS
SLEEVES. 650 Poydras Street Suite 1250
R = 1" REF NOTE 7 3. REINFORCEMENT SHOWN IS IN ADDITION TO SCHEDULED SLAB REINFORCEMENT. New Orleans, LA 70130

Lb
4. SCHEDULED SLAB MESH REINFORCEMENT MAY BE CUT AS REQUIRED TO MISS PIPE

D
504.412.2000 tel 504.412.2001 fax
CJP SLEEVES. www.manningarchitects.com
T&B 5. REFER TO MECHANICAL, ELECTRICAL, AND PLUMBING
CJP TYP DRAWINGS FOR LOCATION AND SIZE OF SLEEVES.
6. ISOLATED PIPE SLEEVES THAT ARE SMALLER THAN 5" AND DO NOT INTERRUPT
CONSULTANTS
REINFORCEMENT DO NOT REQUIRE THE USE OF THIS DETAIL.
EQ NOTE 4 10'-0" (120") 7. THIS DETAIL SHOULD NOT BE USED FOR OPENING GROUPS WITH DIAMETERS LARGER THAN CIVIL
SIGN CONVENTION 12". CONSULT STRUCTURAL ENGINEER FOR FRAMING OF SUCH CONDITIONS. AECOM
°
θ<85 P2 h,z : (+) IS MORE
30°< UPHILL ELEVATION
8. PROVIDE HALF OF INTERRUPTED REINFORCEMENT PLUS ONE ADDITIONAL BAR OF SAME 232 Third Street, Suite 201
REFER TO NOTE 4 SLAB SURFACE SIZE ON EACH SIDE OF EQUIVALENT RECTANGULAR OPENING. PROVIDE A MINIMUM OF Baton Rogue, LA 70801
85 PLATE "A" EA PROFILE 1-#4 TOP AND BOTTOM EACH SIDE OF OPENING.
°< PLATE "B" EA 225.663.4309 tel
θ< SIDE OF WEB h2 z 2= h 2 - h1 1-#4 TOP AND BOTTOM, TYPICAL www.aecom.com
9 SIDE OF WEB

0
0°
+M -M
2 2 P1 LANDSCAPE

2" TYPICAL
ELEVATION
AECOM
h1 DATUM

2'-0"
1360 Peachtree Street NE Suite 500

0
NOTE 1 A Atlanta, GA 30309
PLATE "A" MEASURE OF FLOOR LEVELNESS 404.965.9627 tel
(4 REQD) SNUG-TIGHTENED BOLTED CONNECTION WF BEAM, SEE PLAN SIGN CONVENTION q : www.aecom.com
Project Management Initials: Designer: Designer Checked: Checker Approved: Approver

WITH STANDARD HOLES, RESISTANCE BY 12" 12" TROUGH, q>0

BOLTS TO SHEAR LOAD SHALL BE BY REFER TO NOTE 1 0 0

COST ESTIMATING
SLAB SURFACE CREST, q<0
SHEAR/BEARING DAVIS LANGDON An AECOM Company
P1 PROFILE P3
710 Second Avenue Suite 100
PLATE "B" d2 d3 Seattle, WA 98104
NOTE 1 P2

0
0
(4 REQUIRED) PL TO COLUMN 206.343.8119 tel 206.343.8541 fax
q3 = d3 - d2

0
FLANGES NS, FS h1 h3 2'-0" www.davislangdon.com

0
DOUBLE BENT ANGLES = h3 - 2h2 + h1

0
DOUBLE ANGLE h2
0

1-#4 TOP

0
"B" "B" DATUM PLAN FOR A>=3" AND
BOTTOM
CODE CONSULTANT

2" TYPICAL
MINIMUM SIZE FILLET COPE AND REINFORCE BEAM FOR WF COLUMN TYP FP&C Consultants, Inc.
WELD. REFER TO AISC BENDING AND SHEAR AS REQUIRED NOTES:
MEASURE OF FLOOR FLATNESS L 3770 Broadway
TO SUPPORT REACTION A Kansas City, MO 64111
SPECIFICATIONS. 1. SLIP-CRITICAL BOLTED SHEAR CONNECTION USING A325 BOLTS, UNLESS NOTED OTHERWISE. 816.931.3777 tel 816.931.3378 fax
SNUG-TIGHTENED BOLTED CONNECTION USING BOLTS IN WEB CONNECTION SHALL BE SNUG-TIGHTENED ONLY PRIOR TO WELDING FLANGES NOTES:

2'-0" MINIMUM
www.fpc-consultants.com
A325 BOLTS IN HORIZONTAL SHORT-SLOTTED AND PRETENSIONED AFTER WELDING FLANGES. 1. FL = LEVELNESS F-NUMBER

Ld+L/2
HOLES IN ANGLE, RESISTANCE BY BOLTS TO 2. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. FL= 12.5 _______ WHERE z = MEAN VALUE OF ALL x FLOOR READINGS
SHEAR LOAD SHALL BE BY SHEAR/BEARING SECTION 3. PROVIDE PREDESIGNED SHEAR CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF (3 x Sz) + z Sz = STANDARD DEVIATION OF ALL z FLOOR READINGS BRANDING/GRAPHICS
D NOTES: INFINITE SCALE DESIGN GROUP

W
STEEL CONSTRUCTION MANUAL WHERE APPLICABLE.
NOTES: 1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. 4. MINIMUM FILLET WELD SIZE FOR SINGLE PLATE SHEAR CONNECTIONS SHALL BE 5/8 TIMES THE 2. FL= FLATNESS F-NUMBER 16 Exchange Place
2. REFER TO PLAN FOR CONNECTION DESIGN REACTIONS. PLATE THICKNESS. FL= 4.57 _______ WHERE q = MEAN VALUE OF ALL q FLOOR READINGS Salt Lake City, UT 84111
1. SEE PLAN FOR LOCATION OF BEAM OPENINGS.
3. PROVIDE PREDESIGNED CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF STEEL 5. WHEN BEAM FRAMES ON ONLY ONE SIDE OF COLUMN OR WHEN BEAM MOMENTS ARE SIGNIFICANTLY (3 x Sq) + q Sq = STANDARD DEVIATION OF ALL q FLOOR READINGS 801.363.1881 tel 801.363.1841 fax
2. BEAM OPENINGS ARE NOTED THUS 1 ON PLAN. CONSTRUCTION MANUAL WHERE APPLICABLE.
NOTES: UNBALANCED ( I M + M I >>0), STRENGTHEN COLUMN WEB AS REQUIRED. www.infinitescale.com
1. SHOP WELD CONNECTION TO DEVELOP BEAM REACTION. REFER TO PLANS. 3. VERIFY SIZE AND LOCATION OF ALL BEAM OPENINGS WITH GENERAL CONTRACTOR PRIOR TO STEEL 4. SHOP WELD CONNECTION TO DEVELOP BEAM REACTION (2 x WELD SIZE RETURN AT TOP). 6. ALL CJP WELDS: CVN = 20FT-LBS AT 40°F. 3. FL AND F F SHALL BE STATISTICALLY DETERMINED ACCORDING TO ASTM E 1155 EQUIVALENT
2. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. FABRICATION. 7. INCREASE CONTINUOUS STIFFENER TOP OR BOTTOM PLATE THICKNESS TO ACCOMODATE DIFFERENT "STANDARD TEST METHOD FOR DETERMINING FLOOR FLATNESS AND LEVELNESS USING RECTANGULAR REFER TO NOTE 8
THE F-NUMBER SYSTEM."
FOOD SERVICE CONSULTANT
BEAM DEPTHS AND DIFFERENT SIZE BEAMS WHEN MOMENT CONNECTIONS OCCUR IN STRONG AND OPENING
WEAK COLUMN DIRECTION. 4. REFER TO CONCRETE SPECIFICATIONS FOR REQUIRED FL AND F F VALUES Ld+W/2 S20 CONSULTANTS, INC.
2'-0" MINIMUM
PLAN FOR A<3" 452 W. James Way
Cary, IL 60013
TYPICAL SKEWED BEAM-TO-BEAM TYPICAL SHEAR CONNECTION TYPICAL MOMENT CONNECTION ADDITIONAL REINFORCEMENT AROUND 224.717.1999 tel 847.516.5855 fax
SHEAR CONNECTION TYPICAL STEEL BEAM OPENING SCHEDULE AT COLUMN FLANGE AT COLUMN WEB TYPICAL SLAB SURFACE TOLERANCE PIPE SLEEVES www.S20Consultants.net

12 NO SCALE 05120-CN-BMBM-04
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
11 12" = 1'-0"
00860-FL-BMOPG-2X
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
10 NO SCALE 05120-CN-BMCOL-01
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
9 1" = 1'-0" 8 NO SCALE 03300-FL-SLTOL-01
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2011
7 NO SCALE 03300-FL-SLOPG-02
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2010
ENGINEERING
MAZZETTI NASH LIPSEY BURCH
650 Poydras Street Suite 2242
New Orleans, LA 70130
NOTE 7 615.329.4460 tel 615.329.3660 fax
NOTE 8 NOTE 8
DECK STIFFENING RIB DECK STIFFENING DECK STIFFENING RIB www.mazzetti.com
RIB STRUCTURAL
STUD "STRONG" POSITION STUD "WEAK" POSITION STUD "WEAK" POSITION STUD "STRONG" POSITION
Last Plotted: 5/8/2013 11:03:24 AM

WALTER P MOORE
NEAREST SUPPORT BEAM CENTERLINE BEAM CENTERLINE NEAREST SUPPORT 920 Main Street, Tenth Floor
Kansas City, MO 64105
816.701.2100 tel 816.701.2200 fax
www.walterpmoore.com

SPORTS TECHNOLOGIES
A A WRIGHTSON JOHNSON HADDON & WILLIAMS
BEAM 4801 Spring Valley Road Suite 113
CENTERLINE Dallas, TX 75244
SUPPORT SUPPORT 972.934.3700 tel 972.934.3720 fax
B-B (GIRDER OR COLUMN) (GIRDER OR COLUMN) www.wjhw.com
SINGLE STUD ORIENTATION ELEVATION
REGISTRATION
NOTES CONTINUED:
TYPICAL, NOTE 3 TYPICAL, TYPICAL, 7. IF MOMENT IS INDICATED ON DRAWINGS: DECK STIFFENING RIB CL
SINGLE PLATE, TYPICAL, NOTE 6 NOTE 5 (Mu) A (Mu) B
TYPICAL NOTE 6 NOTE 5 (Pu) = AND (Pu) =
HIGH STRENGTH SLIP BEAM B A 0.95D B 0.95D NEAREST SUPPORT BEAM CENTERLINE
CRITICAL BOLTS TO A B
DEVELOP BEAM REACTION IF MOMENT IS NOT SHOWN: ADDITIONAL SHEAR CONNECTORS
C AT MAXIMUM SPACING, SEE NOTE 4
0.9FyZx A 0.9FyZx B

1" MINIMUM
(TYPICAL)
(Pu) = AND (Pu) = 1 STUD
STIFFENERS IF A B PER FLUTE
STANDARD HOLE 0.95D 0.95D B B
REQUIRED FOR A B N N1 N2 N... Nn N
AT MID-DEPTH OF WEB CRIPPLING 0

CONNECTION Pu = MINIMUM OF (Pu) AND (Pu) (KIPS).

A B
DB

WELD A WHERE: Fy = YIELD STRENGTH OF BEAM (KSI). 2 STUDS

DA

ZxA ,ZxB = PLASTIC MODULUS OF BEAM (IN 3).

S
PER FLUTE
HIGH STRENGTH SLIP BEAM A
SINGLE PLATE SHEAR CRITICAL BOLTS TO D ,D = DEPTH OF BEAM (INCHES).
(DEEPER BEAM) (Pu)B A B
CONNECTION DEVELOP BEAM REACTION 4 x STUD DIAMETER
E = ECCENTRICITY (INCHES). 0

CASE A CASE B CASE C

E

NARROW
FLANGE
(Pu)A WT SECTION 8. WELD A SHALL BE DESIGNED TO DEVELOP THE FOLLOWING FORCES:

WIDTH
BACKING BAR a. SHEAR: V = Pu (KIPS).
2 STUDS UNIFORM LOAD MULTIPLE GIRDER SEGMENTS CANTILEVER
PER FLUTE
NOTE 5 SINGLE PLATE SHEAR 1/2" THICK x 6" WIDE b. MOMENT: M = Pu x E (KIP-INCHES).
CONNECTION L STIFFENER PLATE 9. FLANGE THICKNESS AND WIDTH OF WT SECTION SHALL BE EQUAL TO OR
NOTES: LARGER THAN THAT OF DEEPER BEAM.
BACKING BAR (12" MINIMUM)
1. BOLTS IN WEB CONNECTION SHALL BE SNUG-TIGHTENED PRIOR TO WELDING OF FLANGES. MINIMUM SIZE FILLET WELD 10. YIELD STRENGTH OF WT SHALL BE THE SAME AS THAT OF DEEPER BEAM.
SNUG-TIGHTENED BOLTED CONNECTION USING COPE AND REINFORCE BEAM FOR 2. SLIP-CRITICAL BOLTED CONNECTION IN WEB USING A325 BOLTS IN HORIZONTAL SHORT-SLOTTED 11. WEB OF BEAM B SHALL BE INVESTIGATED FOR WEB CRIPPLING AND 3 STUDS NOTES:

S S
REFER TO AMERICAN
A325 BOLTS IN HORIZONTAL SHORT-SLOTTED BENDING AND SHEAR AS REQUIRED HOLES UNLESS NOTED OTHERWISE. RESISTANCE BY BOLTS TO SHEAR SHALL BE BY FRICTION, REINFORCED IF REQUIRED. PER FLUTE 1. N = NUMBER OF SHEAR CONNECTORS SPECIFIED ON PLAN. SHEAR CONNECTORS SHALL BE DISTRIBUTED ALONG
INSTITUTE OF STEEL
HOLES IN PLATE, RESISTANCE BY BOLTS TO TO SUPPORT REACTION PROPORTIONED USING THE STANDARD HOLE VALUE ON A CLASS "A" SURFACE. 12. WT SECTION WEB SHALL BE DESIGNED TO DEVELOP MOMENT M AND THE LENGTH OF THE BEAM AS SHOWN IN CASES A THROUGH C.
CONSTRUCTION MANUAL
SHEAR LOAD SHALL BE BY SHEAR/BEARING, 3. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. SHEAR V DEFINED IN NOTE 7 ABOVE AS FOLLOWS: 2. REFER TO GENERAL NOTES FOR PLAN NOTATION.
TYPICAL 4. PROVIDE PREDESIGNED SHEAR CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF STEEL NOTES: 3. REFER TO GENERAL NOTES FOR SHEAR CONNECTOR DIAMETER AND LENGTH. CONFORMED SET

NARROW
CONSTRUCTION LRFD MANUAL WHERE APPLICABLE.

FLANGE
1. BOLTS IN WEB CONNECTION SHALL BE SNUG-TIGHTENED PRIOR TO WELDING OF FLANGES AND FULLY 4. MAXIMUM SPACING OF SHEAR CONNECTORS SHALL BE AS FOLLOWS.

WIDTH
5. IF MOMENT IS SHOWN ON DRAWINGS, PARTIAL PENETRATION WELD TO DEVELOP MOMENT CAN 3 STUDS
TIGHTENED AFTER WELDING OF FLANGES. a. BEAMS PERPENDICULAR TO DECK SPAN: SMALLER OF 36" OR 8 TIMES TOTAL SLAB THICKNESS

S
BE USED IN LIEU OF COMPLETE JOINT PENETRATION WELD. FOR THIS CASE, WELD SHALL BE 4M PER FLUTE
2. SLIP-CRITICAL BOLTED CONNECTION IN WEB USING A325 BOLTS IN HORIZONTAL SHORT-SLOTTED L= (INCHES) b. BEAMS PARALLEL TO DECK SPAN: 8 TIMES TOTAL SLAB THICKNESS
REQUIRED TO DEVELOP THE BEAM FLANGE FORCE COMPUTED AS FOLLOWS: Pu = (Mu)/(0.95D), HOLES UNLESS NOTED OTHERWISE. RESISTANCE BY BOLTS TO SHEAR SHALL BE BY FRICTION, 0.9Fy t s 5. WHERE THE SPECIFIED NUMBER OF SHEAR CONNECTORS IS LESS THAN THE BEAM SPAN LENGTH DIVIDED BY THE
NOTES: AND
WHERE: Mu = DESIGN MOMENT (KIP-FEET). PROPORTIONED USING THE STANDARD HOLE VALUE ON A CLASS A SURFACE. MAXIMUM SPACING (SEE NOTE 4), ADDITIONAL SHEAR CONNECTORS SHALL BE PROVIDED SUCH THAT THE
1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. V 0

4 x STUD DIAMETER
D = BEAM DEPTH (INCHES). 3. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. L= (INCHES) MAXIMUM SPACING IS NOT EXCEEDED AT ANY LOCATION IN THE SPAN.
2. PROVIDE PREDESIGNED CONNECTIONS AS SHOWN IN AMERICAN
Pu = BEAM FLANGE FORCE (KIPS). 4. PROVIDE PREDESIGNED SHEAR CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF STEEL 0.54Fy t s 6. WHERE STEEL DECK CORRUGATIONS DO NOT ALLOW FOR AN EVEN SPACING OF SHEAR CONNECTORS WITH ONE
INSTITUTE OF STEEL CONSTRUCTION MANUAL WHERE APPLICABLE.
6. MINIMUM FILLET WELD SIZE SHALL BE 5/8 TIMES THE PLATE THICKNESS. CONSTRUCTION MANUAL WHERE APPLICABLE.
0

STUD IN EACH FLUTE, ADDITIONAL STUDS IN A SECOND ROW (OR THIRD ROW WHERE REQUIRED) SHALL BE PLACED
PACKAGE ISSUED DATE:
3. MINIMUM FILLET WELD SIZE SHALL BE 5/8 TIMES THE PLATE THICKNESS. WHERE t s = WT STEM THICKNESS (INCHES). 4 STUDS
5. MINIMUM FILLET WELD SIZE FOR SINGLE PLATE SHEAR CONNECTIONS SHALL BE 5/8 TIMES THE PLATE SUCH THAT THE HIGHEST DENSITY OF SHEAR CONNECTORS OCCURS NEAR THE BEAM SUPPORT. 2013.05.08

S
THICKNESS. L = WT LENGTH (INCHES). PER FLUTE 7. EACH SHEAR CONNECTOR TO BE PLACED IN "STRONG" POSITION (FURTHEST FROM BEAM CENTERLINE).
6. IF MOMENT IS SHOWN ON DRAWINGS, PARTIAL PENETRATION WELD TO DEVELOP MOMENT CAN L SHALL BE TAKEN AS THE LARGER VALUE OF THE TWO EQUATIONS ABOVE 8. SHEAR CONNECTORS MAY ONLY BE PLACED IN "WEAK" POSITION WHEN THERE ARE MULTIPLE STUDS PER FLUTE.
BE USED IN LIEU OF COMPLETE JOINT PENETRATION WELD. BUT SHALL NOT BE LESS THAN 12 INCHES. REFER TO PLAN VIEW AT LEFT FOR PERMISSIBLE CONFIGURATIONS.
TYPICAL BEAM-TO-BEAM TYPICAL BEAM-TO-BEAM S = LARGER OF 3" OR
9. SHEAR CONNECTORS HAVE HIGHEST CAPACITIES WHEN PLACED AS SHOWN. IF STUDS ARE NOT PLACED PER
THIS DETAIL, 25% MORE STUDS MUST BE INSTALLED. EQUALLY SPACE ADDITIONAL STUDS ALONG THE BEAM. ISSUE / REVISION
4 x STUD DIAMETER
SHEAR CONNECTION MOMENT CONNECTION TYPICAL BEAM-TO-BEAM MOMENT CONNECTION A-A
B
18 NO SCALE 05120-CN-BMBM-02
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2012
17 NO SCALE 05120-CN-BMBM-06
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2012
16 NO SCALE 05120-CN-BMBM-07
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2012
PLAN

TYPICAL SHEAR CONNECTOR PLACEMENT DIAGRAMS - STUDS IN "STRONG" POSITION

14 NO SCALE 05050-FL-SHCON-01
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2009

k DETAIL REFER TO NOTE 1

COLUMN FIELD WELD STABILIZING SHOP WELDED
DIMENSION BENT PLATE 1/4x4 CONNECTION TO W+g
DEVELOP BEAM NOTE 4 SNUG-TIGHTENED BOLTED CONNECTION
BEAM W WITH STANDARD HOLES, RESISTANCE BY REFER TO NOTE 4
STIFFENEER PLATES REACTION
BOLTS TO SHEAR LOAD SHALL BE BY
AS REQUIRED, EXTEND SHEAR/BEARING
TO OPPOSITE FLANGE WORK POINT
NOTE 4
IF OPPOSING MOMENT
d2

EQUAL

1"
d2

CONNECTION IS
d1

d1

PRESENT REFER TO
+M 1 NOTE 1 WORK POINT
NO. DATE DESCRIPTION
1"

+M 2
0

(2) 3/4"Ø SNUG- WORK POINT WORK POINT

KEY PLAN
X

TIGHTENED A325 WORK POINT

θ

g<=3/16" DOUBLE ANGLE DOUBLE ANGLE

BOLTS IN SHORT
SLOTTED HOLES
0
Filename: C:\localdata\Kelly-Revit\NOA\NEW ORLEANS ARENA - CENTRAL.rvt

SINGLE BENT
30°<θ

d1-d2 <= 4", θ > 20°

AS REQUIRED

AND MOMENT

d1-d2 > 4" SINGLE PLATE TO PLATE

FOR SHEAR

SINGLE PLATE
LENGTH, L

θ>

DEVELOP REACTION,
<60°

WELD TO TRANSFER WITH SQUARED

60

FLANGE FORCE REFER TO NOTE 1 EDGE SINGLE PLATE SINGLE BENT

M

1"
6" UM

WITH SQUARED
IN

TO WEB, TYPICAL
0

PLATE
IM

REFER TO EDGE N
d2

NOTE 1 REFER TO
d1

TYPICAL REFER TO NOTE 1

° VERTICAL STIFFENER NOTE 1 BLOCK FLANGES IF REQUIRED ERECTION SEAT ANGLES
< 45
0<θ 1" PLATE FINISHED FOR ERECTION CLEARANCE AND SHIMS AS REQUIRED
TO BEAR, TYPICAL DETAIL A DETAIL B DETAIL C
NOTES:
PROJECT NORTH
1. SLIP-CRITICAL BOLTED SHEAR CONNECTION USING A325 BOLTS, UNLESS NOTED OTHERWISE. STIFFENER PLATE IF NOTES:
θ

A BOLTS IN WEB CONNECTION SHALL BE SNUG-TIGHTENED ONLY PRIOR TO WELDING FLANGES REQUIRED, REFER TO 1. SNUG-TIGHTENED BOLTED CONNECTION USING A325 BOLTS IN HORIZONTAL SHORT-SLOTTED 3. SINGLE PLATE CONNECTION MAY BE USED ONLY WHERE WORKPOINT IS AT NOTES:
AND PRETENSIONED AFTER WELDING FLANGES. NOTE 3 HOLES. RESISTANCE BY BOLTS TO SHEAR SHALL BE BY SHEAR/BEARING. INTERSECTION OF COLUMN FLANGE AND WEB.
NOTES: 1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. PROJECT NUMBER
2. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. 2. FABRICATOR SHALL ASSUME WORKPOINT TO BE LOCATED AT CENTERLINE OF COLUMN FOR 4. SINGLE BENT PLATES SHALL BE DESIGNED FOLLOWING PROCEDURES OUTLINED IN THE 2. REFER TO PLAN FOR CONNECTION DESIGN REACTIONS.
1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA.
NOTES: d1-d2 <= 4", θ <= 20° 3. PROVIDE PREDESIGNED SHEAR CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF VALUES OF X >= 1" AND PROVIDE CONNECTION AS SPECIFIED IN DETAIL A. FABRICATOR SHALL AMERICAN INSTITUTE OF STEEL CONSTRUCTION MANUAL. MINIMUM FILLET WELD SIZE, 3. PROVIDE PREDESIGNED CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF STEEL
2. FABRICATOR SHALL VERIFY THAT SEATED CONNECTION DOES NOT INTERFERE WITH 60263613
1. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. STEEL CONSTRUCTION MANUAL WHERE APPLICABLE. ASSUME LOCATION OF WORKPOINT TO BE AT COLUMN FLANGE-WEB INTERSECTION AND PROVIDE W, SHALL BE 5/8 TIMES THE PLATE THICKNESS.
ARCHITECTURAL, MECHANICAL, ELECTRICAL OR PLUMBING REQUIREMENTS. CONSTRUCTION MANUAL WHERE APPLICABLE.
2. PROVIDE PREDESIGNED CONNECTIONS AS SHOWN IN AMERICAN INSTITUTE OF 4. MINIMUM FILLET WELD SIZE FOR SINGLE PLATE SHEAR CONNECTIONS SHALL BE 5/8 TIMES THE CONNECTION AS SPECIFIED IN DETAIL B WHERE CLEARANCE DOES NOT EXIST FOR DETAIL A TO 5. REFER TO SPECIFICATIONS FOR CONNECTION DESIGN CRITERIA. 4. SHOP WELD ON 3 SIDES TO DEVELOP BEAM REACTION, TYPICAL.
3. IF COLUMN FLANGE INTERFERES WITH VERTICAL STIFFENER PLATE, WELD VERTICAL
STEEL CONSTRUCTION MANUAL WHERE APPLICABLE. PLATE THICKNESS.
STIFFENER PLATE TO COLUMN FLANGE IN LIEU OF COLUMN WEB. PROVIDE FLANGE APPLY. FABRICATOR SHALL APPLY DETAIL C ONLY WHEN LOCATION OF WORKPOINT MUST BE SHEET TITLE
3. WHEN BEAM FRAMES ON ONLY ONE SIDE OF COLUMN OR WHEN BEAM 5. WHEN BEAM FRAMES ON ONLY ONE SIDE OF COLUMN OR WHEN BEAM MOMENTS ARE LOCATED AT COLUMN CENTERLINE AND CLEARANCE DOES NOT EXIST FOR DETAIL A TO APPLY.
STIFFENER PLATE AS SHOWN.
REACTIONS ARE SIGNIFICANTLY DIFFERENT, STIFFEN COLUMN WEB AS SIGNIFICANTLY UNBALANCED ( I M1 + M 2 I >>0), STRENGTHEN COLUMN WEB AS REQUIRED. LOCATION OF WORKPOINTS SHALL BE APPROVED BY THE ENGINEER PRIOR TO SHOP DRAWING STEEL FRAMING TYPICAL
REQUIRED. 6. ALL CJP WELDS: CVN = 20FT-LBS AT 40°F. SUBMITTAL. DETAIL C SHALL NOT BE USED FOR LOADS GREATER THAN 40K. DETAILS
TYPICAL COLUMN STIFFENER SKEWED STEEL BEAM-TO-
ARRANGEMENT FOR OPPOSING TYPICAL MOMENT CONNECTION COLUMN STIFFENED SEAT SHEAR TYPICAL SHEAR CONNECTION
BEAMS OF DIFFERENT DEPTHS AT COLUMN FLANGE CONNECTION FOR HEAVY LOADS TYPICAL SKEWED SHEAR CONNECTION AT COLUMN AT COLUMN WEB SHEET NUMBER
24 23 22 21 19
S0.00.20
05120-CN-BMCOL-07 05120-CN-BMCOL-05
NO SCALE 05120-CN-BMCOL-08
© COPYRIGHT WALTER P. MOORE
NO SCALE © COPYRIGHT WALTER P. MOORE NO SCALE 05120-CN-BMCOL-06
© COPYRIGHT WALTER P. MOORE
NO SCALE © COPYRIGHT WALTER P. MOORE NO SCALE 05120-CN-BMCOL-02
© COPYRIGHT WALTER P. MOORE
AND ASSOCIATES, INC. 2008 AND ASSOCIATES, INC. 2012 AND ASSOCIATES, INC. 2008 AND ASSOCIATES, INC. 2012 AND ASSOCIATES, INC. 2010

Printed on 30% Post-Consumer

Recycled Content Paper 7 6 5 4 3 2 1