PROGRAMMING (Ver:1.

3x)

• When the lift is stand by position, by pressing ENTER button for 2 seconds,
programming mode starts.

Main Program No Program Name

B02:Command Type B02: Command Type

2ButonToplama -> 2ButonToplama
Sub Program No Registered Parameter When this sign on screen
Value parameter value can be changed

• You can choose any program by using UP and DOWN buttons.

• To exit the programming mode ESC button in the main menu is used, Exit Program is
displayed on LCD screen. Press the ENTER button and exit the programming mode;
to return the main menu again press the ESC buton.
• When ENTER button in the main menu is pressed, the program on the screen starts.
• If the program has parameter, an arrow appears at the beginning of the second line of
LCD screen. You can change the parameter value by using UP and DOWN buttons.
To store the value, press the ENTER button and return the main menu. By pressing
the ESC button the registered value is valid and you can return the main menu. If the
program is a function, it is run and Okey appears on LCD screen for 2 seconds.

PARAMETERS

Program Factory Set Parameters / Explanations

A.Language
A.Language Turkce Turkce, English, PyccKNÑ
B.SystemSettings
B01:Lift Type TwoSpeed/VVVF Electrical
Hydraulic
Gearless
B02:Command Type Up/DownMixCo. Up/DownMixCo.
(Car Calls and Floor Calls are connected to the same
terminal. They are collective in both directions)
Down Collect.
(Car calls are collective in both directions, floor calls
are collective in down direction)
Up Collective
(Car calls are collective in both directions, floor calls
are collective in up direction)
Selective Co.
(Car calls are collective in both directions, floor down
calls are collective in down direction, floor up calls are
collective in up direction)
OneWayCollect
(Car calls are collective in both directions; on the entry
floor, car calls are collective in down direction and
under the entry floor, car calls are collective in up
direction)
B03:Num. Of Floor 16 2-24
B04:Car Lamp Time 5 seconds 1-20 seconds
(The duration of car lamp ON)
B05:LockWait Time 15 seconds 5-25 seconds
(After CAM energized waiting time for lock signal)
B06:Max.HighSpeed 15 seconds 10-100 seconds
(Max moving time at high speed between two floors)
B07:Max.Low Speed 10 seconds 5-100 seconds
(Max moving time at low speed)
B08:Parking Time 30 seconds 10-100 seconds
(On stand-by, time of moving to park floor)
B09:Park Floor Passive Passive, 0,1,..23
(On stand-by, park floor to go)
B10:Fire Floor Passive Passive, 0,1,..23
(Target floor when detecting fire warning signal)
B11:StopDelCalls Passive Passive, Active
(When pressed the stop button if the parameter value
is passive, car calls are kept in the memory and vice
versa)
B12:DoublexSelect Passive Passive
A Panel
B Panel

B13:Phase Protect Not Sequence Passive

Not Sequence
Sequence 50Hz
Sequence 60Hz
B14:PTC Control Active Passive, Active

B15:Phase Level 50 0-100

(It can be controlled phase level sensitivity, when the
parameter value is increased it can be accepted
existing phases if their voltage levels are low)
B16:RX Delay Time 1500 ms Passive, 10-5000 ms
(In speed control systems, when limit switch is on,
selection of stripping distance)
B17:Ins.Mov.Type ToLimitSwitch ToLimitSwitch
(In inspection mode, car is moved to up and down limit
switches)
ToExactFloor
(In inspection mode, car is moved to up and down floor
levels)
B18:Star-Triangle 400 ms Passive, 10-5000 ms
(Selection of star-triangle relay (RT) convert time for
hydraulic lifts)

B19:ValveSt.Motor 1500 ms Passive, 10-5000 ms

(Motor run time after the valves closed for hydraulic
lifts)
B20:Hyd.Re-level. Passive Passive, Active
(Re-levelling for hydraulic lifts)

B21:PositionReset Passive Passive, Active

(After the power off, when the card is energized, the
car is moved to floor which has down limit bi-stable
switch)

B22:Max. Car Calls 8 1-24

(Maximum car calls accepted in the cabin)
B23:StopFunction Only Stop Only Stop
(When stop (120) signal is cut, only lift is stopped; no
operation is done about the car calls. End of the floor
wait time, back to the normal working position)
Block Calls
(When stop (120) signal is cut, all car calls are
registered and lift is stopped. After the stop signal, wait
for any car call. After the car call, registered calls and
the new call is collated and back to the normal working
position)
B24:Top LessFloor Passive Passive, 1,2,..5
(In doublex working, up direction missing floor number
of one of the lifts)
B25:LowerLessFlo. Passive Passive, 1,2,..5
(In doublex working, down direction missing floor
number of one of the lifts)
B26:Gong Timing When Stop When Stop
(Gong signal is given when the car is stopped)
While Slowing
(Gong signal is given when the car is slowing for the
target floor)
Passive
B27:Entry Floor 0 0-7
(Selection of entry floor used for OneWayCollective
command type)
B28:GrayBin.Start 0 0-5
(At the up missing floor lifts, selection of the starting
number of gray-code or binary output)
B29: CallSCProtect Active Passive, Active
(If the parameter is active short-circuit protection of the
call lamps are provided by microcontroller and vice
versa)
B30:CarSerialCard Active Passive, Active
(If serial communication card will be used, it must be
chosen active)
B31:Fl. Detection Pulse Pulse
Encoder
B32:OSG/BrakeCtrl Active Passive, Active
Cancel A3 (Puk:000000)
(At geary machine systems, over speed governor
selenoid control card MLA3 must be used. If it is used
for the lifts that is not suitable to En81-1/2 + A3
standards, to do this parameter “passive”, ML65X user
must declear to our firm with writings and must accept
the responsibility)
B33:Elect.Re-lev. Passive Passive, Active
(If needed re-levelling, this parameter is chosen active
and MLKR1 door bridging card must be used)

C.Door Settings
C01:DoorTypeSet A Flr00 CarDo. (For each floor, A side door type can be set one by
one and can be set at the same time)
C02:DoorTypeSet B Flr00 NoDoor (For each floor, B side door type can be set one by
one and can be set at the same time)
C03:A D.LimitType Without Limit With Limit, Without Limit
(Limit type selection of A side door mechanism)
C04:B D.LimitType Without Limit With Limit, Without Limit
(Limit type selection of A side door mechanism)
C05:DoorRelay Set A=65xB=Seri65 A=65xB=Seri65
(A side door open/close signals are relays on 65X,
B side door open/close signals are relays on SERI65)
B=65xA=Seri65
(B side door open/close signals are relays on 65X,
A side door open/close signals are relays on SERI65)

C06:Wait At Floor 5 seconds 1-99 seconds

(At full automatic door systems, stay opened time of
automatic door; at only indoor systems, if the door
doesn’t open after the car stopped, selection the time
of the next call)

C07:PhotocellTime Passive Passive, 1,2,..99 seconds

(Selection the time of cutting photocell signal and
starting the nudging signal)

C08:Door OpenMax. 180 seconds 10-180 seconds

(When the door stayed open, selection the time of
warning)

C09:CloseButDelay 2 seconds Passive, 1,2,..20 seconds

(Delay time of close buton detection)

C10:Adv.Door Open Passive Passive, Active

C11:Dir.-Op.Style Passive Passive, Active

(If parameter value is passive, when the direction
arrows are on, the same floor call is not imported. If
parameter value is active, when the direction arrows
are on and if the same floor call is come, the automatic
door is opened)

C12:Door WaitOpen Passive Puk:000000

(At full automatic door lifts, selection of waiting the
door opened. This situation is not suitable to En81-1/2
+ A3 standards. To do this parameter active, ML65X
user must declear to our firm with writings and must
accept the responsibility)

D.DisplaySetting
D01:FloorDisp.Set Flr00 Disp 0 Flr00-23 Disp 0-19,1A,1b,1c,1d
(Display datas that will be screened on floors are
changed)

D02:TargetF.Flash Passive Passive, Active

(If this parameter is selected, in every floor, target floor
is flashed twice)
 E.Prog. Inputs

(Programmable Inputs Sub Section)

Factory Settings Factory Settings

for Electrical Lifts for Hydraulic Lifts

E01:ML65X-EIN1 MLKS10-EXO1 K16 OpenLimit

E02:ML65X-EIN2 MLKS10-EXO2 K19 CloseLimit

E03:ML65X-EIN3 Down Re-lev. Overload

E04:ML65X-EIN4 Up Re-level. Not Used

E05:ML65X-EIN5 Overload 141 (Fixed)

E06:ML65X-EIN6 Fire Fire

E07:ML65X-EIN7 Earthquake Earthquake

E08:ML65X-EIN8 Open Open

E09:ML65X-EIN9 Close Close

E10:MLSERI65-EIN1 Vatman Vatman

E11:MLSERI65-EIN2 K16 OpenLimit K16 OpenLimit

E12:MLSERI65-EIN3 K19CloseLimit K19CloseLimit

Assignable Functions

1- MLKS10-EXO1 (MLKS10 communication input 1)

2- MLKS10-EXO2 (MLKS10 communication input 2)
3- Down Re-lev. (Down re-levelling input)
4- Up Re-level. (Up re-levelling input)
5- Overload (Overload contact)
6- Earthquake (Earthquake input)
7- Open (Open button)
8- Close (Close button)
9- Full Load (Full load contact)
10- Vatman (Vatman key input)
11- Fireman (Fireman key input)
12- K16 OpenLimit
13- K19CloseLimit
14- Panic (Panic button input)
15- Driver Fault (Inverter fault input at UPS rescue)
16- Change Dir. (Change direction input at UPS rescue)
 F.Prog. Outputs

(Programmable Outputs Sub Section)

Factory Settings Factory Settings

for Electrical Lifts for Hydraulic Lifts

F01:ML65X-RY Re-Lev. Speed Not Assigned

(Motor-Valve Auxiliary Relay)

F02:ML65X-RT AtFloorSignal Not Assigned

(It can be set (Star-Triangle Relay)
at KS10 rescue)

F03:ML65X-RB Ups Contactor Inspection

F04:ML65X-OUT1 Gong Gong

F05:ML65X-OUT2 Middle Speed Hyd.Re-lev.M.

F06:ML65X-GC1 Gray-Code M0 Gray-Code M0

F07:ML65X-GC2 Gray-Code M1 Gray-Code M1

F08:ML65X-GC3 Gray-Code M2 Gray-Code M2

F09:ML65X-GC4 Gray-Code M3 Gray-Code M3

F10:MLSERI65-EO1 Nudging Nudging

F11:MLSERI65-GCx Gray-Code Gray-Code

Assignable Functions

1- Inspection
2- Car Lamp
3- Re-Lev. Speed (Re-levelling speed output at electrical lifts)
4- Ups Contactor (UPS-Inverter contactor at UPS rescue)
5- Gong
6- Hyd.Re-lev.M. (Lower power motor output at re-levelling in hydraulic lifts)
7- Middle Speed (Output when the target floor is the nearest floor at electrical lifts)
8- Gray-Code M0
9- Gray-Code M1
10- Gray-Code M2
11- Gray-Code M3
12- Gray-Code M4
13- Binary M0
14- Binary M1
15- Binary M2
16- Binary M3
17- Binary M4
18- Nudging (At full automatic door lifts, output at the end of photocell blocking time)
19- AtFloorSignal
20- Fault(Invers)
 G.Maint.Settings
G01:Mainten.Time 240 Days 10-240 Days
(The number of days for the maintenance warning)
G02:AtEndOfM.Time Only Warn Only Warn
SystemBlocked
G03:Maintenanced? No Yes, No
(After the maintenance it is run, day and hour datas
are deleted, working number after maintenance is
deleted and saved faults are deleted)
G04:Delete Faults? No Yes, No
(All stored faults are deleted)
H.RescueSettings
H01:Rescue Type Resc.WithKS10 Resc.WithKS10
RescueWithUPS
Gearless VVVF
(At gearless machine systems, rescue operation with
VVVF motor control)
GearlessBrake
(At gearless machine systems, rescue operation with
openning brake only)
H02:Rescue Delay 5 seconds 1-15 seconds
(After the detection of main power is cut, selection of
waiting time to start the rescue operation)
H03:RescueMaxTime 40 seconds 10-200 seconds
(Selection of maximum movement time at rescue)
H04:Res.JF M.Time Passive Passive, 0,1-10,0 seconds
(At rescue operation, after the detection of JF,
selection of needed time to re-levelling)
I.Shaft Learning
I01:Learn Shaft No Yes, No
(If this parameter is chosen “Yes”, shaft learning
procedure is started)
I02:HighSpd.Slow. 120 cm 10-500 cm
(Starting distance selection of passing from the high
speed to slow speed to the exact floor)
I03:Mid.Spd.Slow. 80 cm 10-500 cm
(Starting distance selection of passing from the high
speed to slow speed when going to the nearest floor at
high speed lifts)
I04:Low Spd.Slow. 70 mm 1-200 mm
(While approaching to the target floor, selection of
cutting distance of low speed signal)
I05:Dist.ToMidSpd 60 cm 1-500 cm
(To give the high speed signal, selection of the nearest
floor minimum distance)
I06:Reader Lenght 30 cm
I07:817 Position Between0-1Fl. Between0-1Fl.
Between1-2Fl.
(Selection position of 817 lower limit switch)
I08:Up Correct Flr01 05mm Flr00-23, All -99, 0, 99mm
(Selection of precision levelling adjustment in up
direction for each floor)
I09:Down Correct Flr00 05mm Flr00-23, All -99, 0, 99mm
(Selection of precision levelling adjustment in down
direction for each floor)
I10:Floor Height Flr01 0mm Flr01-23, 1mm =0cnt
(After shaft learning, tracing of measured floor heights
and count number per mm)
 J.GeneralSetings
J01:Factory Set ? No Yes, No
(All parameter values are changed into factory
settings)

J02:ResetCounters No Yes, No
(Total working number reset)

J03:Change Passw. 0000 (Changing password)

J04:Cancel Passw. No Yes, No

(Password is cancelled, new value is 0000)

J05:DelMLKR1Error No Yes, No
(Stored faults info is deleted about MLKR1 card)

J06:Del UCM Error No Yes, No

(Stored faults info as a result of UCM is deleted)

J07:UCM Up Test No Yes, No

J08:UCM Down Test No Yes, No

J09:Auto Tuning No Yes, No

J99:Version Ver:1.26.01
Update:08.04.2013