siegling transilon

conveyor and processing belts

Calculation methods –
conveyor belts

Contents
2 Introduction

3 Terminology

5 Unit goods
conveying systems

11 Dimensioning force-
dependent take-up systems

12 Bulk goods
conveying systems

15 Calculation example
for unit goods conveying

Siegling – total belting solutions

Introduction

This brochure contains advanced equations, figures and

recommendations, based on our longstanding experience.
Results calculated can however differ from our calculation
program B_Rex (free to download from the Internet at
www.forbo-siegling.com).

These variations are due to the very different approaches

taken: while B_Rex is based on empirical measurements
and requires a detailed description of the machinery, the
calculation methods shown here are based on general, sim-
ple physical equations, supplemented by certain factors that
include a safety margin.

In the majority of cases, the safety margin in calculations

in this brochure will be greater than in the corresponding
B_Rex calculation.

Further information on machine design can be found in

our brochure, ref. no. 305 “Recommendations for machine
design.”

2
Terminology

Key to the Designation Abbreviation Unit

abbreviations Drum and roller width

Belt width
b
b0
mm
mm
Calculation factors C.. –
Drum and roller diameter d mm
Drive drum diameter dA mm
Rolling resistance of support rollers f –
Tensile force F N
Maximum belt pull (on the drive drum) F1 N
Minimum belt pull (on the drive drum) F2 N
Force of the tensioning weight FR N
Effective pull FU N
Tensioning drum weight F TR N
Steady state shaft load on the drive drum FWA N
Initial value of the shaft load FW initial N
Relaxed shaft load on the return drum FWU N
Acceleration due to gravity (9.81m/s2) g m/s2
Difference in the drum radii (crowning) h mm
Conveying height hT m
Relaxed belt pull at 1% elongation per unit of width k1% N/mm
Support roller pitch on upper side l0 mm
Transition length lS mm
Support roller pitch on return side lu mm
Geometrical belt length Lg mm
Length of conveyor lT m
Mass of the goods conveyed over the entire length conveyed
m kg
(total load)
Mass of the goods conveyed on the top side (total load) m1 kg
Mass of the goods conveyed on the return side (total load) m2 kg
Mass of the belt mB kg
Mass of the goods conveyed per m length conveyed on the upper
m'0 kg/m
face (line load)
Mass of all rotating drums, except for drive drum mR kg
Mass of the goods conveyed per m length conveyed on the return
m'u kg/m
side (line load)
Mechanical motor power PM kW
Mechanical power calculated on the drive drum PA kW
Production tolerance Tol %
Friction coefficient when running over roller µR –
Friction coefficient for accumulated conveying µST –
Friction coefficient when running over table support µT –
Belt velocity v m/s
Volume flow for bulk goods conveying V∙ m3/h
Total take-up range X mm
Belt sag yB mm
Drum deflection yTr mm
Margin for take-up range Z mm
Machine’s angle of inclination α °
Arc of contact on the drive drum (or snub roller) β °
Opening angle on the tensioning drum γ °
Belt elongation (pre-tensioning with weight) ΔL mm
Permitted angle of inclination for unit goods δ °
Elongation at fitting ε %
Maximum belt elongation εmax %
Drive efficiency η –
Bulk density of goods conveyed ρS kg/m3

3
4
Unit goods conveying systems

Load examples
m = lT . Weight of conveyed goods per metre
to establish the
FU = µR . g . (m + mB + mR ) [N] maximum effective
pull Fu [N]

FU = µT . g . (m + mB  ) + µR . g ( m
  B  + mR ) [N]
2 2

FU = µT . g . (m1 + m2 + mB ) [N]

Direction conveyed upwards:

FU = µR . g (m + mB + mR ) + g . m . sin α [N]

Direction conveyed downwards:

FU = µR . g (m + mB + mR ) – g . m . sin α [N]

Direction conveyed upwards:

FU = µT . g ( m + mB  ) + µR . g ( mB  + mR ) + g . m . sin α [N]
2 2
Direction conveyed downwards:
FU = µT . g ( m + mB  ) + µR . g ( mB  + mR ) – g . m . sin α [N]
2 2

FU = µT . g ( m +   mB ) + µR . g ( mB   + mR ) + µST . g . m [N]

2 2

FU = please enquire [N]

FU = please enquire [N]

5
Unit goods conveying systems

Friction coefficients µS for 0, A0, E0, UH, V2H, U2H, TXO

NOVO U1, V1, VH
various coatings (guidelines) T, U0, P V5H, V10H (Amp Miser)
µT (table) 0.33 0.33 0.5 0.5 0.18
µT (galvanised slider beds) – – – – 0.24
µR (roller) 0.033 0.033 0.033 0.033 –
µST (accumulated) 0.33 0.33 0.5 0.5 –

Please note: The friction coefficients stated are based on experience with older friction surfaces
that have been subjected to standard wear and tear and soiling. These friction coefficients are about
1.5 times higher than those for new surfaces.

Maximum belt pull F1       

P · η · C1 · 1000
F₁ = FU . C1 [N] F1 = M
      v [N]

If effective pull FU can be calculated If the effective pull FU cannot be

calcu­lated, F1 can be established from
the motor power installed PM.

Factor C1 Siegling Transilon

V3, V5, U2, A5, E3 V1, U1, UH, U2H, V2H, V5H
(applies to the drive drums) Underside coating
Arc of contact β 180° 210° 240° 180° 210° 240°

Smooth steel drum

dry 1.5 1.4 1.3 1.8 1.6 1.5
wet 3.7 3.2 2.9 5.0 4.0 3.0

Lagged drum
dry 1.4 1.3 1.2 1.6 1.5 1.4
wet 1.8 1.6 1.5 3.7 3.2 2.9

Siegling Transilon
0, U0, NOVO, E0, A0, T, P X0 (Amp Miser)
Underside coating
Arc of contact β 180° 210° 240° 180° 210° 240°

Smooth steel drum

dry 2.1 1.9 1.7 3.3 2.9 2.6  
wet not recommended not recommended

Lagged drum
dry 1.5 1.4 1.3 2.0 1.8 1.7 
wet 2.1 1.9 1.7 not recommended

Minimum diameter of the drive drums dA

    FU · C3 · 180
dA = [mm]
       b0 . β

6
  

Factor C2      
F1 N
≤ C2 [ mm ] if the value F1 is larger than C2,
Checking the Transilon type selected b0
  b0
a stronger belt type (with a higher k1% value) must be used.
In the case of perforated belts please
note: calculate the load-bearing belt C2 is a metric indicating the belt type’s maximum tension:
width b0 based on the number of per- C2 = ε max . k1%
forations which decrease cross sec- the product data sheets include specifications on the εmax maximum elongations during
tions. Staggered perforations in partic- operation. If example calculations and rough estimates without a data sheet are required,
ular can reduce the load-bearing belt the following assumption can be made (but not guaranteed):

width considerably. Reduce the figure

Tension High-tech Elastic fabric
for the load-bearing belt width b0 by a Standard polyester Aramid
member polyester fabric types (EL)
further 20 % to take tolerances for per- fabric („E“) („AE“)
Type („E …/H“) EL 0/V
forations and fabric into account. Examples E 2/1, E3/1, E 4/2, E 8/H, E 18/H AE 18/H, AE 48/H, EL 0/V
of type E 6/1, NOVO, E 8/2, AE 80/3, AE 100/3,
classes E 10/M, E 12/2, E15/2, AE 140/H, AE
E 15/M, E 18/3, 140/3
E 20/M, E 30/3, E 44/3
εmax in % 1.5 1.2 1.0 8

If subjected to high temperatures of over 100  °C, the C2 factors change. Please contact us.

Faktor C3 Siegling Transilon

V3, V5, U2, A5, E3 V1, U1, UH 0, U0, NOVO, T, P
(applies to the drive drums) Underside coating

Smooth steel drum

dry 25 30 40
wet 50 not recommended not recommended

Lagged drum
dry 25 25 30
wet 30 40 40

Mechanical capacity calculated

on the drive drum PA F ·v
PA = U [kW]
1000

Mechanical capacity required PM   

PA
PM =  [kW] = the next largest, standard motor is selected
η
 

Standard High-tech Elastic fabric

Elongation at fitting limits Aramid
Tension member polyester fabric polyester fabric types
(„AE“)
(„E“) („E …/H“) („EL“)
min. elongation at fitting [%] 0.3 0.2 0.15 1.5
The table on establishing the C2 factor max. elongation at fitting [%] 1.0 0.8 0.8 5.0
shows product examples for the ten-
sion member concerned.

7
Unit goods conveying systems

Take-up range for

screw-operated take-up
systems
The following factors must be taken
into account when establishing the
take-up range: –Tol +Tol ε z

1. The approximate magnitude of
elon­gation at fitting ε of the belt, x
resulting from the belt load. To
establish ε, see pages 7 and 8.
3. Any external influences that might Generally, depending on the load,
2. The production tolerances (Tol) of necessitate greater elongation elongation at fitting, ranging from
the belt as regards the length. (ten­sioning) than usual, or might approx. 0.2 % to 1 %, is sufficient, so
require a safety margin, such as for that normally a take-up range x of
example the impact of temperature, approx. 1 % of the belt length is ade-
stop-and-go operation. quate.

Guidelines for shaft load At rest

at rest with tensile force F
When you are estimating the shaft
loads, please assess the different levels
of belt pull when the conveyor is at
rest and in a steady state.
FW1 = FW2 = 2 . F F ≈ ε% . k1% . b0 [N]

Guidelines for Head drive in steady state forces

elongation at fitting ε
for head drives
The minimum elongation at fitting for
head drives is:

FU/2 + 2 . F2 F2 = F1 – FU FWA = F1 + F2
ε≈ . [%]
2 k1% . b0

8
Guidelines for elongation Tail drive in steady state forces
at fitting ε for tail drives
The minimum elongation at fitting for
return side drives is:

FU/2 + 2 · F2 + FU
ε = [%] F2 = F1 – FU
2 · k1% · b0

Guidelines for
elongation at fitting ε
for return-side drives
The minimum elongation at fitting for
operating head drives is:

FU (C1 – K)
ε = [%]
k1% · b0
Return side drive in steady state

K for head drives = 0.75

K for return-side drives = 0.62
K for tail drives = 0.25

9
Unit goods conveying systems

Guidelines for steady Typical drive drum β = 180° Typical end drum β = 180°
state shaft load
FWA = F1 + F2 [N] FW3 = 2 . F2 [N]

Typical snub roller β = 60° Typical drive drum β ≠ 180°

FW6 = 2 . F2 . sin (β/2) [N] FWA = F12 + F22 – 2 . F1 . F2 . cos β [N]

Shaft load when Tension members made of synthetic This implies that higher belt forces
tensioning belts materials display significant relaxation FWinitial will occur when tensioning the
behaviour. As a result, the relaxed k1% belt. They will have to be taken into
value is taken as a basis for calculating account when dimensioning the drum
belts in line with ISO 21181. It describes and its components (bearings). The fol-
the probable long-term force-elonga- lowing value can be assumed as a ref-
tion properties of the belt material that erence:
has been subjected to stress due to
deflection and load change. This pro- FWinitial = FW . 1.5
duces the calculation force FW.
In critical cases, we recommend you
contact application engineers at Forbo
Siegling.

10
Dimensioning force-dependent
take-up systems

Establishing FR In weight-loaded take-up systems, the The tension weight must be able to
tension weight must generate the min- move freely. The take-up system must
imum belt pull F2 to achieve perfect be in­stalled behind the drive section.
grip of the belt on the drive drum Reverse operation is not possible. The
(spring, pneumatic and hydraulic take- take-up range depends on the effec-
up systems work on a similar principle). tive pull, the tensile force F2 required,
elongation of the belt ΔL, the produc-
tion tolerance Tol, the safety margin for
tensioning Z and the belt selected.

FR = 2 . F2 – F TR  [N] FU F1

F2

Example for establishing the tension F2

weight FR [N] at 180° arc of contract
(FTR = tensioning drum weight [N]).
F TR FR

γ _ FU F1
FR = 2 · F2 · cos F TR [N]
2
F2

Example for establishing the tension F2

γ
weight FR [N] at an angle γ according
to the drawing (FTR = tensioning drum
weight [N]).
F TR FR

Establishing belt In force-driven take-up systems, the overall elongation of the belt changes,
elongation ΔL according to the level of the effective pull. The change in belt elongation ∆L has
to be absorbed by the take-up system. For head drives ∆L is calculated as

FU/4 + F TR + FR 
∆L =   · Lg [mm]
k1% · b0

11
Bulk goods conveying systems

Longitudinal angle of Bulk goods δ (approx.°) Bulk goods δ (approx.°)

Ash, dry 16 Flour 15 – 18
inclination δ Ash, wet 18 Salt, fine 15 – 18
Soil, moist 18 – 20 Salt, rock 18 – 20
Guidelines for the longitudinal angle of Grain, except oats 14 Loam, wet 18 – 20
inclination δ permissible in various bulk Lime, lumps 15 Sand, dry, wet 16 – 22
goods. The machinery’s actual angle of Potatoes 12 Peat 16
inclination α must be less than δ. Gypsum, pulverised 23 Sugar, refined 20
Gypsum, broken 18 Sugar, raw 15
Wood, chips 22 – 24 Cement 15 – 20
These values depend on the particle
Artificial fertilizer 12 – 15
shape, size and mechanical properties
of the goods conveyed, regardless of
any conveyor belt coating.

Bulk density of some Goods conveyed Bulk density ρS [103 kg/m3] Goods conveyed Bulk density ρS [103 kg/m3]
Ash, cold, dry 0.7 Gypsum, broken 1.35
bulk goods ρS Soil, moist 1.5 – 1.9 Flour 0.5 – 0.6
Grain (except oats) 0.7 – 0.85 Clinker 1.2 – 1.5
Wood, hard 0.6 – 1.2 Loam, dry 1.5 – 1.6
Wood, soft 0.4 – 0.6 Loam, wet 1.8 – 2.0
Wood, chips 0.35 Sand, dry 1.3 –1.4
Charcoal 0.2 Sand, wet 1.4 – 1.9
Pulses 0.85 Soap, flakes 0.15 – 0.35
Lime, lumps 1.0 – 1.4 Slurry 1.0
Artificial fertilizer 0.9 – 1.2 Peat 0.4 – 0.6
Potatoes 0.75 Sugar, refined 0.8 – 0.9
Salt, fine 1.2 – 1.3 Sugar, raw 0.9 – 1.1
Salt, rock 2.1 Sugarcane 0.2 – 0.3
Gypsum, pulverised 0.95 – 1.0

Volume flow V∙ b0 [mm] 400 500 650 800 1000 1200 1400
for belts lying flat Angle of surcharge 0° 25 32 42 52 66 80 94
Angle of surcharge 10° 40 57 88 123 181 248 326

The table shows the hourly volume

flow (m3/h) at a belt velocity of v =
1 m/s. Conveyor belt lying flat and
horizontal. The belt is equipped with
20 mm high longitudinal profiles T20
on the belt edges of the top face.

12
Volume flow V∙ for b0 [mm] 400 500 650 800 1000 1200 1400
troughed conveyor belts Troughed angle 20°
in m3/h at a belt velocity of 1 m/s. Angle of surcharge 0° 21 36 67 105 173 253 355
Angle of surcharge 10° 36 60 110 172 281 412 572

Troughed angle 30°

Note: Angle of surcharge 0° 30 51 95 149 246 360 504
Angle of surcharge 10° 44 74 135 211 345 505 703
Under real world conditions, the
theoretical values for volume flow are
hardly ever reached as they only apply
to horizontal belts with perfectly even
loads. Uneven loads and the properties
of the goods conveyed can decrease
the amount by approx. 30 %.

Conveying angle
Factor C6 2 4 6 8 10 12 14 16 18 20 22
α [°]

Factor C6 1.0 0.99 0.98 0.97 0.95 0.93 0.91 0.89 0.85 0.81 0.76
In inclined conveying, the theoretical
quantity of goods conveyed is slightly
less. It is calculated by applying the fac-
tor C6 which depends on the convey-
ing angle α.

Factor C4 IT [m] 25 50 75 100 150 200

Factor C4 2 1.9 1.8 1.7 1.5 1.3

Additional effective pull, for example
from scrapers and cleaning devices, is
taken into account by including the
factor C4.

13
Bulk goods conveying systems

Rolling resistance for support rollers f f = 0.025 for roller bearings

f = 0.050 for slide bearings

Establishing the mass of goods conveyed m V∙ . δS . lT . 3.6

m= [kg]
v

Establishing the effective pull FU FU = g · C4 . f (m + mB + mR ) ± g · m . sin α [N]

(–) downwards Calculation as for unit goods

(+) upwards

Support roller pitches The support roller pitch depends on If maximum sag of 1 % is permitted,
the belt pull and the masses. The fol- (i.e. yB = 0.01 l0)
lowing equation is used to calculate it:
Recommendation l0 max ≤ 2b0
lu ≈ 2 – 3 l0 max

      .
yB . 800 . F 8 F
l0 = [mm] l0 = [mm]
m'0 + m'B m'0 + m'B
    

l 0 = Support roller pitch on upper side in mm

yB = Maximum conveyor belt sag in mm
F = Belt pull in the place concerned in N
m‘0 + m‘B = Weight of goods conveyed and belt in kg/m

14
Calculation example
for unit goods conveying

In a goods sorting system, conveyor

belts are loaded with goods and sent
to the distribution centre. Horizontal
conveying, skid plate support, return
drive systems as shown on the sketch,
drive via the top face of the belt, drive
drum with lagging, screw-operated
tensioning system, 14 support rollers.
Proposed belt type: Siegling Transilon
E 8/2 0/V5H S/MT black (996141) with
k1% = 8 N/mm.
End drums 1, 2, 6 Length of conveyor lT = 50 m
Snub rollers 3, 7, 8 Geometrical belt length Lg = 105000 mm
Drive drum 5 Belt width b0 = 600 mm
Support rollers 4, 9, and various Total load m = 1200 kg
tension drums 6. Arc of contact β = 180°
v = ca. 0.8 m/s g = 9.81 m/s2
Mass rollers mR = 570 kg
(all drums except
for 5)

mB   m
Effective pull FU [N] FU = µT . g (m + ) + µR . g ( B + mR )
2 2
   

157.5    157.5   
FU = 0.33 . 9.81 (1200 + ) + 0.033 . 9.81 ( + 570)
2 2

FU ≈ 4340 N

m = 1200 kg
µR = 0.033
µT = 0.33
mB = 157.5 kg (from 2.5 kg/m2 . 105 m . 0.6 m)

Maximum belt pull F1 [N] FU = 4350 N F1 = FU . C1

C1 = 1.6 F1 = 4350 . 1.6
F1 ≈ 6960 N

Checking the belt type selected F1 = 6960 N   F1

    ≤ C2
  b0
b0 = 600 mm
k1% = 8 N/mm 6960 ≤ 1.5 . 8 N/mm
600

11.6 N/mm ≤ 12 N/mm

The belt type has been chosen

correctly.

15
Calculation example
for unit goods conveying

FU = 4340 N FU . C3 . 180°

Minimum drive drum diameter dA = [mm]
C3 = 25 b0 . β

β = 180°
4340 . 25 . 180°
b0 = 600 mm dA = [mm]
600 . 180°
    

dA = 181 mm

dA dimensioned at 200 mm

   .
Power PA on the drive drum FU = 4350 N FU v
PA = [kW]
v = 0.8 m/s 1000
   
     .
4350 0.8
PA =
1000

PA ≈ 3.5 kW

Motor power required PM PA  = 3.5 kW PA
PM =  [kW]
η
η = 0.8 (assumed)

3.5
PM =  [kW]
0.8

PM ≈ 4.4 kW

PM at 5.5 kW or higher

Minimum elongation at fitting FU = 4350 N F (C – K)
ε = U .1 [%]
for return drive k1% b0
C1 = 1.6
K = 0.62
k1% = 8 N/mm for
4350 (1.6 – 0.62)
ε =  [%]
E 8/2 0/V5H S/MT black 8 . 600

b0 = 600 mm
ε ≈ 0.9 %

16
Shaft load in steady state drum drum 2 Simplified calculation assuming FW2 = 2 . F1
(return drum)
β = 180°
FW2 = 2 . 6960 N

F1 = 6960 N FW2 ≈ 13920 N

Shaft load in steady state drum drum 1 F2 = F1 – FU FW1 = 2 . F2

(return drum)
F2  = 6960 – 4350
FW1 = 2 . 2610 N
F2 = 2610 N
FW1 ≈ 5220 N

Shaft load in steady state drum drum 5 F1 = 6960 N FW5 = F1 + F2

(Drive drum)
F2  = F1 – FU
FW5 = 6960 + 2610
F2 = 6960 – 4350
F2 = 2610 N FW5 ≈ 9570 N

Shaft load in steady drum 3 (snub roller) Governed by minimum belt pull F2, FW3 is
calculated using the equation on page 10.

Shaft load at rest At rest, tensile forces are defined on

the top and underside by elongation at F = ε [%] . k1% . b0 [N]
fitting ε. The tensile force F is calculat-
To compare rest and steady state ed according to:
modes, please observe the different
shaft loads in drum 1.

FW1 at rest = 8640 N Example for a drum with β = 180°

FW = 2 . F
FW1 steady state = 5220 N Arc of contact F  = 2 . 0.9 . 8 . 600
W
(In our example, this force is exerted FW ≈ 8640 N
Note: equally on drums 1, 5 and 6 because of
When designing machinery, both the 180° arc of contact).
modes must be taken into account.

When β ≠ 180° the following applies FW =  F12 + F22 – 2 . F1 . F2 . cos β

when determining FW (F1 = F2 can be
FW = [N]
assumed at rest).

17
Calculation example
for unit goods conveying

Take-up range

–105 +105 473 200

210

883

Tol = ± 0.2 % . Tol . Lg

2
­­ ε . Lg
ε = 0.9 % 100
+
 100
  + Z 
Lg = 105000 mm X= [mm]
2
Z = 200 mm

2 . 0.2 . 105000   0.9 . 105000

+
100 100
X=     + 200 [mm]
2

X = 210 + 473 + 200 [mm]

X ≈ 883 mm

18
19
Siegling – total belting solutions

Committed staff, quality oriented organization and

­production processes ensure the constantly high standards
of our products and services. The Forbo Siegling Quality
Management System is ­certified in accordance with ISO 9001.

In addition to product quality, environ­­mental protection is

an important corporate goal. Early on we also intro­duced an
environmental management system, certified in accordance
with ISO 14001.

06/18 · UDH · Reproduction of text or parts thereof only with our approval. Subject to change.
Ref. no. 304-2
Forbo Siegling service – anytime, anywhere
The Forbo Siegling Group employs more than 2,500 people.
Our products are manufactured in ten production facilities
across the world. You can find companies and agencies with
warehouses and workshops in over 80 countries.
Forbo Siegling service points are located in more than
300 places worldwide.

Forbo Siegling GmbH

Lilienthalstrasse 6/8, D-30179 Hannover
Phone +49 511 6704 0
www.forbo-siegling.com, [email protected]