Epimastic 7200 SR

EPIMASTIC 7200 (SR)
Epoxy Mastic Primer
PRODUCT A high build Epoxy zinc phosphate primer containing inert and anticorrosive pigments. This
material is specially designed to give fast output and excellent corrosion resistance under
DESCRIPTION medium corrosive environment condition.
 Can be applied up to 200 micron DFT in single coat.
DESIGNED USE  As a chemically resistant primer for process equipment, pipe work etc.
 As a general maintenance coating for onshore and offshore installations
 Suitable as primer for upto C4 Environment as per ISO12944 Part 2 along with suitable
intermediate and topcoats
PHYSICAL DATA VOLUME SOLIDS

78% + 2%
(based on ASTM D2697)
TYPICAL DRY FILM THICKNESS 150 microns
WET FILM THICKNESS 195 microns
THEORETICAL COVERAGE 5.2 m2/litre @ 150 microns DFT
VOC as supplied
200 gms /ltr
(Based on ASTM D 3960)
COLOUR Grey
FINISH Slight Sheen
APPLICATION METHOD OF APPLICATION :

DETAILS This is the recommended method of application:
AIRLESS SPRAY 5 - 10% Thinner may be added depend up on easiness.
Tip Size: 0.43 - 0.53 mm (0.017-0.021 in)
Pressure: 110-160 kg/cm2 (1600-2300 psi)
This is also a suitable method of application. 10 - 20%
Thinner may be added depend up on easiness.
CONVENTIONAL SPRAY
Tip Size: 1.80 mm -2.20 mm (0.071-0.087 in)
Pressure: 40-50 psi (2.75-3.45 kg/cm2)
May be used for difficult shapes or touch-up; however
BRUSH OR ROLLER additional coats may be required to achieve the
recommended film thickness.
DRYING TIME:
Surface Re coating Interval
Touch Dry Hard Dry Pot Life
Temperature Minimum Maximum
25°C 2 Hr 16 Hrs 7 Hrs 7 days 3 Hrs
35°C 1 Hr 12 Hrs 4 Hrs 7 days 1½ Hrs
45°C 40 min 8 Hrs 2½ Hrs 7 days ½ Hr
100°C 10 min 20 min 30 min 7 days
NO. OF COMPONENTS Two
Mixing Ratio 7 part base to 1 part Hardener (by volume)
Do not apply this product if the Relative Humidity
Application Conditions exceeds 85% or if the substrate temperature is within
3°C of the dew point
ADDITIONAL Thinner / Cleaning solvent) Solvalux 7-45

Storage Instruction Store in a cool shaded dry area
INFORMATION Flash Point Mixed 36°C
Packaging 20 Liters
Shelf Life 12 months from the date of manufacture.
March 2016 Version 1 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774
EPIMASTIC 7200 (SR)
Epoxy Mastic Primer
SURFACE For best results, the surface should be treated as follows prior to painting.
 Remove all wax, oil and grease by solvent cleaning in accordance with the guidelines given by
PREPARATION SSPC-SPI.
 Where necessary remove weld spatter and round off all rough weld seams and sharp edges to a
smooth surface. Special care must be taken on weld areas to remove flux and spatter. Welds should
be ground back to avoid pockets where corrosion can occur.
 Abrasive blast-clean to a minimum standard of Sa 2½ Swedish Standard SIS 055900 or ISO 8501-
1: 1988.
 Any surface defects revealed by blast cleaning should be ground, filled or treated in a suitable
manner.
 An average surface profile of 50 microns is acceptable, but this average should not exceed 75
microns.
 After blasting, remove dust from the surface.
 The cleaned surface should be coated before it becomes contaminated. The surface to be coated
must also be clean and dry.
 This product should be over coated with Berger range of 2 pack products.
PRODUCT USE  This product is designed as a primer. It should not remain long without over coating. If directly
RESTRICTIONS exposed to sunlight and outdoor conditions this product will chalk as in case with all epoxy
products.
 This product is not suitable for use in immersed conditions without a topcoat.
 Dry heat resistance up to 120°C.
 May also be applied between 75 and 200 Microns DFT.
 Contact Berger Representative for suggesting suitable paint system.
SAFETY  Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls, goggles,
PRECAUTIONS dust masks and gloves. Use a barrier cream.
 Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe vapour or spray.
 This product is flammable. Keep away from sources of ignition. Do not smoke. Take precautionary
measures against static discharge. In case of fire – blanket flames with foam, carbon dioxide or dry
chemicals
 Refer to MSDS for further information.
FIRST AID  Eyes: In the event of accidental splashes, flush eyes with water immediately and obtain medical
advice
 Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
DO NOT USE solvent or thinners.
 Inhalation: Remove to fresh air, loosen collar and keep patient rested.
 Ingestion: In case of accidental ingestion, DO NOT INDUCE VOMITING.
Obtain immediate medical attention
The information provided on this data sheet is not intended to be complete and is provided as general advice only. It is the responsibility
DISCLAIMER of the user to ensure that the product is suitable for the purpose for which he wishes to use it. As we have no control over the treatment of
the product, the standard of surface preparation of the substrate, or other factors affecting the use of this product, we are not responsible
for its performance nor would we accept any liability whatsoever or howsoever arising from the use of this product unless specifically
agreed to in writing by us. The information contained in this data sheet may be modified by us from time to time, and without notice, in
the light of our experience and continuous product development.
March 2016 Version 1 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774

Epimastic 7200 SR

Uploaded by

Copyright:

Available Formats

Epimastic 7200 SR

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Epimastic 7200 SR

Uploaded by

Copyright:

Available Formats

EPIMASTIC 7200 (SR)

Epoxy Mastic Primer

PHYSICAL DATA VOLUME SOLIDS

APPLICATION METHOD OF APPLICATION :

ADDITIONAL Thinner / Cleaning solvent) Solvalux 7-45

You might also like