Scribd Logo
Upload

Welcome to Scribd!

  • 566 views

    Bolt & Nut Torque Table PDF

    Uploaded by

    Fandy Maulan
    This document provides bolt size and torque specifications for maintenance of a SH330 machine. It lists 20 critical bolt locations by code and specifies the nominal bolt diameter, recommended wrench size, and tightening torque range in N*m. Bolts should be tightened alternating between left and right, and oil should be applied to critical bolt threads. Bolts should be re-tightened after 50 hours of new machine use and every 250 hours after.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Bolt & Nut Torque Table PDF

    Uploaded by

    Fandy Maulan
    566 views6 pages
    This document provides bolt size and torque specifications for maintenance of a SH330 machine. It lists 20 critical bolt locations by code and specifies the nominal bolt diameter, recommended wrench size, and tightening torque range in N*m. Bolts should be tightened alternating between left and right, and oil should be applied to critical bolt threads. Bolts should be re-tightened after 50 hours of new machine use and every 250 hours after.

    Original Title

    Bolt & Nut Torque Table.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides bolt size and torque specifications for maintenance of a SH330 machine. It lists 20 critical bolt locations by code and specifies the nominal bolt diameter, recommended wrench size, and tightening torque range in N*m. Bolts should be tightened alternating between left and right, and oil should be applied to critical bolt threads. Bolts should be re-tightened after 50 hours of new machine use and every 250 hours after.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    566 views6 pages

    Bolt & Nut Torque Table PDF

    Uploaded by

    Fandy Maulan
    This document provides bolt size and torque specifications for maintenance of a SH330 machine. It lists 20 critical bolt locations by code and specifies the nominal bolt diameter, recommended wrench size, and tightening torque range in N*m. Bolts should be tightened alternating between left and right, and oil should be applied to critical bolt threads. Bolts should be re-tightened after 50 hours of new machine use and every 250 hours after.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Bolt Size and Torque Table SH330

    Maintenance Section

    Bolt Size and Torque Table


    Bolt and Nut Tightening
    • Tighten alternating between left and right and top and bottom so that uniform tightening force is
    applied.

    456C

    • For bolts at critical locations, apply engine oil to the threads for a uniform tightening force without
    catching on the thread peaks.
    • For bolts and nuts at critical locations and at locations that cannot be inspected from the outside,
    use wire, cotter pins, folded washers, or the like to securely prevent turning.

    • If Loctite was used on a removed bolt (there is something white sticking to the bolt when it is
    removed), clean the old Loctite off with cleaning fluid, dry the bolt, then apply 2 - 3 drops of Loctite to
    the thread section of the bolt.

    Bolt and nut retightening [after 1st 50 hr. for new machine] [every 250 hr.]
    Tighten and retighten bolts and nuts in each section according to the table. Also before and after
    day-to-day work, inspect for loose or fallen out bolts and nuts. Retighten any that are loose and
    replace any that have come out.
    Inspect and retighten after the first 50 hr. for a new machine and every 250 hr. after that.

    81 SST-09-08-008EN
    1
    Bolt Size and Torque Table
    Retightening Torque Table
    Bolt nominal Tightening torque
    Code Retightening location Wrench
    diameter [N•m]

    1 Travel motor M24 36 mm 900 - 1051

    2 Drive sprocket M20 30 mm 521 - 608

    3 Take-up roller M16 24 mm 267 - 312

    4 Upper roller M20 30 mm 521 - 608

    5 Lower roller M24 36 mm 902 - 1049

    6 Track guard M24 36 mm 902 - 1049


    7 Shoe M24 32 mm 1236 - 1510
    8 Counterweight M33 50 mm 1685 - 1960

    9 Turntable bearing M24 36 mm 900 - 1050

    10 Swing unit M24 36 mm 900 - 1050

    11 Mount M20 30 mm 289 - 337

    12 Engine Front bracket M10 17 mm 64 - 73

    13 Rear bracket M12 19 mm 109 - 127

    14 Radiator M16 24 mm 147 - 176

    15 Flange M10 17 mm 64 - 73
    Hydraulic pump 17 mm
    16 Pump M20 367 - 496
    hexagon socket head

    17 Hydraulic oil tank M16 24 mm 233 - 276

    18 Fuel tank M16 24 mm 233 - 276

    19 Control valve M16 24 mm 267 - 312

    20 Lock bar M16 24 mm 267 - 312


    Center joint
    21 Joint M12 19 mm 54 - 64
    M16 24 mm 78 - 80
    22 Cab
    M10 17 mm 35 - 42
    23 Battery M10 17 mm 20 - 29
    Caution: For items marked with ○ , always apply Loctite #262 or the equivalent and tighten to the
    specified torque.
    The tightening torque in kgf•m is determined with N•m ÷ 9.8.

    The tightening for bolts and nuts not otherwise specified in the table above is as follows.
    Bolt nominal diameter (size) M6 M8 M10 M12 M14 M16 M18 M20
    Wrench [mm] 10 13 17 19 22 24 27 30
    Hexagon bolt Tightening
    [N•m] 6.9 19.6 39.2 58.8 98.1 156.9 196.1 294.2
    torque
    Wrench [mm] 5 6 8 10 12 14 14 17
    Hexagon socket
    head bolt Tightening
    [N•m] 8.8 21.6 42.1 78.5 117.7 176.5 245.2 343.2
    torque

    SST-09-08-008EN 82
    2
    Bolt Size and Torque Table

    83 SST-09-08-008EN
    3
    Bolt Size and Torque Table

    SST-09-08-008EN 84
    4
    Bolt Size and Torque Table

    85 SST-09-08-008EN
    5
    Bolt Size and Torque Table

    SST-09-08-008EN 86

    You might also like