BOQ

Name of work:-Construction of road from Nepalpara to Batabari via Uttar Islakhata including Cross-Drainage works and routine maintenance for
five years under PMGSY for the year 2017-18.

Package No. As-25-213

S/L No. Item No. Items Unit Quantity

1 2 3 4

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs,
saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and
disposal of unserviceable materials and stacking of serviceable material to be used or
1 2.2(i)A auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not Hec. 0.270
exceeding 150 mm in thickness as per Technical Specification Clause 201.(I) By Manual
Means(A) In area of non thorny jungle

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork
2 2.13(A) and Dismantling of Masonry Works as per Technical Specification Clause 202. (B) Above 600 m 7.500
mm to 900 mm dia Hume pipe

Construction of embankment with approved material obtained from borrow pits with a lift
upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet
3 3.4(a) Cum 452.320
requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification
Clause 301.5 (I) Private Land

Construction of subgrade and earthen shoulders with approved material obtained from
borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope
4 3.14(a) Cu.m 973.214
and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical
Specification Clause 303.1. (I) Private Land
 (A)By Mix in Place Method : Construction of granular sub-base by providing well graded
material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in
5 4.1(ii) place method with rotavator at OMC, and compacting with smooth wheel roller to achieve Cum 273.280
the desired density, complete as per Technical Specification Clause 401. (ii) For Grading II
Material

2) WBM Grading 2 - Using stone screening Type-B 11.2 mm for Gr.II : Providing, laying,
spreading and compacting stone aggregates of specific sizes to water bound macadam
specification including spreading in uniform thickness, hand packing, rolling with smooth
6 4.7(2)(A) wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone Cum 130.620
screening/binding materials to fill-up the interstices of coarse aggregate, watering and
compacting to the required density grading 2 as per Technical Specification Clause 405. (B) By
Mechanical Means

3) WBM Grading 3 - Using stone screening Type-B 11.2 mm for Gr.III : Providing, laying,
spreading and compacting stone aggregates of specific sizes to water bound macadam
7 4.7(3)(A) specification including spreading in uniform thickness, hand packing, rolling with smooth Cum 457.660
wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone
screening to fill-up the interstices of coarse aggregate, watering and compacting to the
required density Grading 3 as per Technical Specification Clause 405. (A) By Manual Means

Prime Coat
I) Low porosity
Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of
granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0
8 5.1(i) kg/sqm using mechanical means as per Technical Specification Clause 502 sqm 6106.950
 ii) Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor
at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface
cleaned with Hydraulic broom as per Technical Specification Clause 503.
9 5.2(ii) sqm 6106.950

20mm thick Open-Graded Premix Carpet using Bitumen Emulsion as per Technical
Specification clause 508.2
Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of
13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to
10 5.10 sqm 6106.950
required line, grade and level to serve as wearing course on a previously prepared base,
including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller
capacity, finished to required level and grades to be followed by seal coat of either Type A or
Type B or Type C as per Technical Specification Clause 508.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified
levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification
Clause 510
11 5.12 sqm 6106.950
A By Manual Means
Case - II : Type B
I) Bitumen (S-90)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per
IRC:8 fixing in position including painting and printing, etc as per drawing and Technical
12 10.10(ii) Specification Clause 1703 each 2.000
ii) Ordinary Kilometer Stone (Precast)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per
IRC:8 fixing in position including painting and printing, etc as per drawing and Technical
13 10.10(iii) Specification Clause 1703 each 8.000
iii) 200 m stone (precast)
 A) Retro-reflectorised Traffic Signs
1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as

per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over

aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x

14 10.2A(ii) 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade each 11.000

cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings

and Technical Specification Clause 801

(ii) 60 cm equilateral tringle

A) Retro-reflectorised Traffic Signs

1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as
per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over
aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x
15 10.2A(iii) each 4.000
6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade
cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings
and Technical Specification Clause 801
(iii) 60 cm circular

A) Retro-reflectorised Traffic Signs

1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as
per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over
aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x
16 10.2A(vi) each 1.000
6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade
cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings
and Technical Specification Clause 801
(vi) 60 cmx60 cm square
 Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD
specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded
with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS
angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and
flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes
posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm,
17 10.16 each 0.000
600mm below ground level. The top most diamond plate will be welded to middle plate by
47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides.
Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel
paint of superior quality in required shade and colour. All sections of framed posts and steel
tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and
Annexure 1700.1

Providing and fixing of Citizen information board with Logo as per MORD specifications and
drawing. Two nos. 1.6 mm thick MS sheet duly welded with 5m thick steel plate on back on
edges. The 4 nos. steel plate will be welded horizontaly with 2 nos. 75mm x 75mm of 12 SWG
sheet tube posts duly embadded in cement concrete M-15 grade blocks of 600mm x 600mm x
18 750mm, 750mm below ground level. The 2 nos. steel plate will be welded vertically to 2 nos. sqm 1.000
75mm x 75 mm of 12 SWG sheet tubes posts duly welded to vertcal tubes. All M.S. will be
stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with
ready mixed synthetic enamel paint of superior quality in required shade and colour. All
sections of framed posts and steel tube will be painted with primer and two coats of epoxy
paint as per drawing Clause 1701 and Annexure 1700.1
 Providing and fixing of typical PMGSY Maintenance informatory board with Logo as per MORD
specifications and drawing. One no. MS Plates of 1.6 mm thick(Height 1500mm), duly welded
with MS flat iron 25mm x 5m size on back on edges. The 4 nos. flate MS plate 25mm x 5m on
edges. The 4 nos. flate M.S plate 25mm x 5m size will be welded horizontaly with 2 nos. 75mm
x 75mm of 12 SWG sheet tube posts duly embadded in cement concrete M-15 grade blocks of
19 600mm x 600mm x 750mm, 750mm below ground level. The 2 nos. steel plate will be welded sqm 1.000
vertically to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly welded to vertcal tubes.
All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will
be painted with ready mixed synthetic enamel paint of superior quality in required shade and
colour. All sections of framed posts and steel tube will be painted with primer and two coats
of epoxy paint as per drawing Clause 1701 and Annexure 1700.1MORD

I Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to
cracks, parapet wall and protection work as per drawing and technical specification Clause
20 15.7 1908 each 2.000

ii Maintenance of Slab type Culverts by way of clearing, Cleaning, Erosion repair, repairs to
21 15.7 cracks, parapet walls and Protection works as per drawing and technical specification Clasue each 1.000
1908

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1
including setting out, construction of shoring and bracing, removal of stumps and other
deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and
22 11.1 m3 60.790
backfilling in trenches with excavated suitable material.
I Ordinary soil
Upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per

drawings and technical specifications Clause 802, 803, 1202 & 1203
23 11.4(A)(I)(i) A. With crushed stone. m3 7.600
I P.C.C grade M 10
Nominal mix 1:3:6
 Providing concrete for plain/reinforced concrete in open foundations complete as per
drawings and technical specifications Clause 802, 803, 1202 & 1203
24 11.4(A)(I)(ii) A. With crushed stone. cum 59.270
II P.C.C grade M 15
Nominal mix (1:2.5:5)

Providing concrete for plain/reinforced concrete in open foundations complete as per

drawings and technical specifications Clause 802, 803, 1202 & 1203
25 11.4(A)(I)(iii) A. With crushed stone. cum 3.000
III P.C.C. grade M 20
Nominal mix (1:2:4)

Plain/reinforced cement concrete in substructure complete as per drawings and technical

specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204
26 12.5(iv) cum 2.650
A. With Crushed Stone
IV RCC Grade M25 for height upto 5 m

Supplying, fitting and placing TMT bar reinforcement (Fe 415) in substructrue complete as per
27 12.7 Tonne 0.280
drawings and technical specification Clauses 1002, 1005, 1010 & 1202

MAINTENANCE
28 Routine maintenance for 1st year Km 1.99
29 Routine maintenance for 2nd year Km 1.99
30 Routine maintenance for 3rdyear Km 1.99
31 Routine maintenance for4th year Km 1.99
32 Routine maintenance for 5th year Km 1.99
562.5