Scribd
Upload
114 views1 page

Design of 15m Span Superstructure Re - 19

This document provides calculations to check the anchorage of span reinforcement at the end of a structure. It calculates tensile forces on the reinforcement, checks the capacity of the anchorage reinforcement, and verifies stresses, forces and moments at various sections meet the ultimate limit state capacity requirements.

Uploaded by

vivek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
114 views1 page

Design of 15m Span Superstructure Re - 19

This document provides calculations to check the anchorage of span reinforcement at the end of a structure. It calculates tensile forces on the reinforcement, checks the capacity of the anchorage reinforcement, and verifies stresses, forces and moments at various sections meet the ultimate limit state capacity requirements.

Uploaded by

vivek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Anchorage of Span Reinforcemet at end : ( IRC 112 / clause 16.5.1.

4)
Tensile Force = VED * (al/d) +NED
VED = 110.46 T Factored Shear Force at face of support
d = 1.33 deff at face of support
al = 0.5 *z*(cot q)
z = 1.30 m (z at face of support)
q = 45 deg (angle of concrete strut with longitudinal axis)
NED = 0T

al = 0.651

Tensile Force = 53.9829 Tonne

Area of tensile reinforcement at support section As = 0.0064 m


2

Maximum tensile stress in reinforcement fyd = fyk /gm = 500 /1.15


= 434.783 Mpa

Tensile capacity of anchorage reinforcement Ft = 279.738 Tonne OK


Anchorage provided upto l b.net distance from face of support starting after leaving w/3

CHECK FOR ULTIMATE LIMIT STATE CAPACITY: ( IRC 112 / clause 8.2.1)
Section At unit c/L brg. deff L/8 TS 2L/8 3L/8 4L/8
Dist. From c/L brg. m 0.00 1.21 1.75 2.60 3.50 5.25 7.00

Ast m2 0.0064 0.0064 0.0064 0.0064 0.0064 0.0097 0.0097


deff m 1.3320 1.3320 1.3320 1.3320 1.3320 1.3160 1.3160
lxu m 0.060 0.060 0.060 0.060 0.060 0.090 0.090
CArea m2 0.179 0.179 0.179 0.179 0.179 0.268 0.268
x1 m 0.030 0.030 0.030 0.030 0.030 0.045 0.045
Cu T 279.74 279.74 279.74 279.74 279.74 419.61 419.61
Tu T 279.74 279.74 279.74 279.74 279.74 419.61 419.61
Check (C-T =Zero) 0 0 0 0 0 0 0
xu m 0.075 0.075 0.075 0.075 0.075 0.113 0.113
xu/d 0.056 0.056 0.056 0.056 0.056 0.086 0.086
Check ( xu/d < xu,max/d ) UR,OK UR,OK UR,OK UR,OK UR,OK UR,OK UR,OK

z =(d-x1) m 1.30 1.30 1.30 1.30 1.30 1.27 1.27


MRD = Tu*z Tm 364.20 364.20 364.20 364.20 364.20 533.27 533.27

MED Tm -0.39 120.70 172.80 225.97 284.19 341.88 372.49


check MED < MRD OK OK OK OK OK OK OK

Additional Tensile force due to shear


DFd T 55.44 48.84 47.53 32.45 32.32 19.52 8.32
MED/z +DFD T 55.14 141.54 180.26 206.01 250.61 288.52 301.41
MRD/z 279.74 279.74 279.74 279.74 279.74 419.61 419.61
Check MRD > MED/z +DFD OK OK OK OK OK OK OK

You might also like