Scribd
Upload
68 views2 pages

Signal Generators

Signal generators provide a variety of signals for testing electronic circuits at low powers. They output common waveforms like sine, square, triangular waves and pulse trains. Signal generators must have stable output frequency and amplitude that is controllable and distortion-free with low spurious outputs and noise. Audio frequency signal generators, which produce signals from 20 Hz to 20 kHz, often use RC feedback oscillators like the Wien bridge or RC phase shift oscillator. Standard signal generators are also used to test radio receivers and transmitters, producing known modulated carrier frequencies.

Uploaded by

Hyder Ali Panhwar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
68 views2 pages

Signal Generators

Signal generators provide a variety of signals for testing electronic circuits at low powers. They output common waveforms like sine, square, triangular waves and pulse trains. Signal generators must have stable output frequency and amplitude that is controllable and distortion-free with low spurious outputs and noise. Audio frequency signal generators, which produce signals from 20 Hz to 20 kHz, often use RC feedback oscillators like the Wien bridge or RC phase shift oscillator. Standard signal generators are also used to test radio receivers and transmitters, producing known modulated carrier frequencies.

Uploaded by

Hyder Ali Panhwar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SIGNAL GENERATORS

Introduction:
Signal generator provides variety of different signals for testing various electronic circuits at low
powers. The signal generator is an instrument which provides several different output waveforms
including sine wave, square wave, triangular wave, pulse train and an amplitude modulated
waveform.
Requirements of Laboratory Type Signal Generator:
There are different types of signal generator. But the requirements are common to all
the types.
i) The output frequency of signal generator should be very stable .
ii) The amplitude of output signal of signal generator should be controllable from low values to
relatively large values.
iii) The amplitude of output signal must be stable. the harmonic contents in the output should be as
low as possible. The output signal should be distortion free.
v) The signal generator should provide very low spurious output; that means effect of hum, noise,
jitter and modulation should be negligible.
A F oscillator:
The signal generators which provide sinusoidal waveforms in the frequency range of 20 Hz to 20
kHz are called audio frequency(A.F.) signal generator. Depending upon the load, in modern AF
signal generators a provision is made to select output impedance either 50 n or 600 n. To generate
audio frequency signals, in practice RC feedback oscillators are used. The most commonly used
RC feedback oscillators are Wien Bridge oscillator and RC phase shift oscillator. Let us discuss
both the types of oscillators in detail.
Wien Bridge Oscillator using Op-amp:
The Fig shows the Wien bridge oscillator using an op-amp.
nle resistance R and capacitor C are the components of frequency sensitive arms of
the bridge. The resistance Rf and R1 form the part of the feedback path. The gain of
noninverting op-amp can be adjusted using the resistance Rf and R1. The gain of op-amp
is,

Standard signal generator:


It is extensively used in the testing of radio receivers and transmitters. This is basically
a radio frequency (RF) signal generator. The standard signal generator produces known
and controllable voltages.
Principle of working:
The output of the generator is amplitude modulated or frequency modulated. The
frequency modulation is possible using a carrier signal from RF oscillator. The amplitude
modulation can be done using internal sine wave oscillator. The modulation may be done
by a sine wave, square wave, triangular wave or a pulse also. The setting on the front
pane1 indicates the carrier frequency to be used for modulation.

Source : http://elearningatria.files.wordpress.com/2013/10/ece-iii-electronic-instrumentation-10it35-
notes.pdf

You might also like