emitec ag, birkenstrasse 47, 6343 rotkreuz

tel 041 748 60 10, fax 041 748 60 11

[email protected], www.emitec.ch

EMC Problems
and their Solutions as Experienced
in the EMC Test Lab

Dipl. Ing. HTL M. Fuhrer / EM TEST AG

EM TEST AG
Abstract
This paper will discuss actual EMC problems encountered in electronic products. The EMC
problems are those encountered in EFT, Surge, ESD, power fail and emissions testing.
This paper will show how to correct these problems using various methods. It will make a
case as to why EMC problems should be considered in the initial design of a product before
it submitted to the EMC test lab. Using these methods will result in a product of higher
quality and lower cost.

EMC Problems and their Solutions as Experienced in the EMC Test Lab

1 Introduction...................................................................................................................... 3

2 Cases and Subracks ...................................................................................................... 4

2.1 EMC cases.......................................................................................................................4
2.2 Subrack and Front Panel...................................................................................................5
2.3 Front panel.......................................................................................................................5
3 EMC Design...................................................................................................................... 7
3.1 Example: Design of an EMC Burst generator......................................................................7
3.2 Example: Replacement of a power supply with another with the CE mark.............................8
4 Design according to the EMC requirements ........................................................... 9

5 Conducted Emissions ................................................................................................. 10

5.1 Definition, Origin and Spreading ...................................................................................... 10
5.2 Leakage current.............................................................................................................. 11
5.3 Process of elimination of radio interference ...................................................................... 12
5.4 Systematic overview of radio interference and their remedy............................................... 13
5.5 Example : Effect of filter elements ................................................................................... 14
5.6 Leakage of noise over the GND Layer.............................................................................. 15
6 Plugs and cables........................................................................................................... 16
6.1 Example : Sub D Connector with screened cable.............................................................. 18
6.2 Screened Cables ............................................................................................................ 19
6.3 Choice of cables ............................................................................................................. 20
7 Common interference problems............................................................................... 21
7.1 Burst Test ...................................................................................................................... 21
7.2 ESD............................................................................................................................... 21
7.3 Surge............................................................................................................................. 22
7.4 Power Fail...................................................................................................................... 22

-2-
1 Introduction
Experience in solving EMC problems shows that having just one individual EMC expert in a company, is not
the optimal solution for an efficient development. EMC knowledge must be supported within the company as
broadly as possible. Each coworker must make an important contribution according to his function to develop
an EMC compliant product. An awareness of the EMC design of a product with all involved in development
and production is the only way to guarantee disturbance resistant products.
From experience, approximately 60% all EMC of problems are avoidable by using proper design techniques.
The first EMC considerations must be addressed at the beginning of the Design phase of a product between
developers and the technical designer.
Additional costs of later EMC interference elimination on devices are high. Taking into consideration EMC
measures is more economical at the beginning of the product development. Delaying the product introduction
to the market caused by EMC redesign generates additional costs.
This essay treats the most frequent problems, which occur in an EMC service laboratory. Often there are
many common design flaws that reduce immunity of the devices. The developer and technical designer have
a large influence in designing a device on the first attempt economically with the necessary immunity. It is
important have a basic knowledge of the EMC design failures to be avoided in a successful design. If the
EMC design is not considered in the early product design cycle, the use of expensive EMC protection devices
will be required as a product is about to go into production because only minor modifications are possible at
this late stage.

-3-
2 Cases and Subracks
From the standpoint of EMC design, the case has the primary function of shielding. The case functions as a
path for discharge to earth, and as a screen for the suppression of internal radiated emissions. A low-inductive
ground connection of the individual housing parts is necessary for good EMC behavior. On the market there
are a multiplicity of EMC cases, which fulfill the highest requirements for shielding.

2.1 EMC cases

The main difference between EMC cases and standard cases are:
- Special design for RF use
- Closed housing with special RF screening material
- Cover with no holes or holes with an optimum shielding
- Frontplates with special RF shielding
- Attachment with many screws for better RF shielding

Suggestion
The RF behavior usually exceeds the shielding requirements of the application.
The difference between standard cases and EMC cases is that the EMC case has better RF
shielding and fewer holes and slots.
Holes in the frontplate for displays, connectors and cables are a source of emissions.
Elimination of the source of emissions or screening of components on the printed circuit
boards is usually more economical in reducing emissions.

In comparing the EMC housing of different manufacturers, the method used to make the EMC measurements
must be understood . Thus the indicated screen absorption values can only be conditionally compared.

Manufacturer A Manufacturer B
Figure 1: Display of E and H field with information about the case Figure 2: Information to the test
model and the numbers of frontplates standard

-4-
2.2 Subrack and Front Panel
High ground current disturbances are led away over the module carrier to the housing. Therefore, special
attention must be given to the construction of the module carrier. The components must be interconnected
with low impedance within the module carrier. When assembling the module carrier, a fixed connection with
good contacts between the individual sections is important. Material with a conductive surface is preferred to
an isolating surface such as an anodized coat.
Often the connection between the thread strip and the subrack is left to chance. With grub screws (s. fig. 3),
which penetrate the isolating anodized skin, a perfect connection to the frame is guaranteed.
Figure 3 : Stud bolt for conductive connection
between the thread strip and subrack

2.3 Front panel

The frontplates from distributors are often anodically
oxidized. The attachment of the front plate is often
made with plastic nipple. The front plate does not
have a good connection to the frame. During the ESD
test, the front plate works as an antenna and radiates
the ns impulses directly into electronics. The results
are disturbances or failures of the equipment.

Figure 4: No electrical connection between the

front panel and subrack.

Remedy
- Rearside of the panels conductive (electro-chemical
pickling)
- Screw socket with conductive material ( figure 5 )
- Using a countersunk screw without screw socket

Figure 5 : Conductive attachment of the front

panel

-5-
2.3.1 Example : ESD test to front plate
Front plates without electrical connection to the frame, act as an antenna during ESD testing and radiate the
impulses directly inside the device. This leads to EMC disturbances.

Original design Front plates with anodized coats. Use of plastic screws for frontplate
attachment. No measurable electrical connection between front plate
and frame.
Result after ESD test ESD disturbance at test level <2kV
View an audible flash over between front plate and housing with the
consequence that the front plate takes the ESD potential up to the
flash over and radiate directly into electronics.
The impulse field strengths are equal to or larger than military NEMP
impulses ( 50kV/m Trise <10ns ).
EMC Corrective Measure The anodized coat on the rear side of the front plates is sanded off.
This results in a measurable connection from the front plate to the
housing.
Check after the modification No influence with ESD test
The front plate can pass the charge directly to the housing and does
not radiate in inside the device.

Tips
• For the subrack use material that is electrically conductive on the surface.
• Use front plates with electro-chemical pickling or behind-mill on the rear side. Use con-
ductive plates with a foil on front.
• Define the connection from the thread strip to the tie bar with a grub screw.
• Design the connection between front plate and subrack with conductive material.
• Make a simple check of the electrical connection with an ohmmeter. ( < 0.5 Ω including
measuring cables )
• Contacting possibly with EMI shielding gaskets

-6-
3 EMC Design
The design of electrical equipment requires that the design consider EMC behavior. Each functional module of
the device must be associated to an interference class (disturbed, normal and calm). Simultaneously, the
internal disturbers of the equipment must be verified and eventually they need separate shielding. With the
specifications of the position of plugs and control elements the designer has additional information on where
to arrange the peripherals in the equipment. (Figure 6)
Now the partitioning of the device follows into the different EMC zones. The dispatching of the functions into
the different interference classes will result in an interference-resistant design from an EMC standpoint. As a
result of further requirements the definite design arises.

3.1 Example: Design of an EMC Burst generator

Figure 6 : EMC zones

Zone I: Disturbed zone

High voltage rectifier
Pulse forming burst pulse,
Decoupling filter to line
Zone II: Normal zone
Line filter spatially separated
Line transformer
Signal filter
Input knob and display
Zone III: Calm zone
Control device

Tips for increasing the immunity

• Mains after entrance into the device must be filtered immediately. Often the mains first
pass through the fuses, switches and indicator lights. The mains lines that are not filtered
act as an antenna and radiate disturbances into the device inside. Thus the disturbances
bypass the filter which becomes ineffective.
• In and output lines must be protected by capacitors to ground or inductances (low fre-
quency signals) or must be screened (data lines or low level sense signals). Over these
lines no disturbances may penetrate neither outward nor arrive into the inside.
• The conducted emission is effective to both sides. Therefore a correct filtering contrib-
utes substantially to the increase of immunity. The position of the filter at the power input
is meaningful only, if the source of the noise causes no larger disturbances inside the
equipment.
• Basically screened and unscreened sections inside a device must be separated strictly
spatially.

-7-
3.2 Example: Replacement of a power supply with another with the CE mark
For the internal voltages a switched power supply unit is selected, where the CE mark is attached already.
The using of components with CE mark does not warrant that your equipment fulfills the request of CE
mark automatically. The Noise immunity can be very easily reduced by awkward constructions.
Situation
A power supply is replaced by a product with CE Mark. The new power supply is smaller in dimensions and is
installed in place of the previous power supply.
The new power supply has another pin allocation. To reduce costs, the mechanical layout was not changed.
The mechanical attaching bolts fit in place where the old ones were attached. (Figure 7)

Results of the immunity test:

Burst : Disturbance above 400V

Surge : Flashover at 2000V L-PE

Figure 7 : Original design

Causes:
Burst test : By using of the old layout for the mains cable, the mains cable crosses over the low voltage sup-
ply cables, whereby the cables touched. The burst impulses are capacitively coupled over to the adjacent
lines. With burst pulses of only 400V the 5V and 15V supply voltages were already so disturbed that the de-
vice no longer worked properly.
Surge test : The mounting bolt had the same thread and the technical designer did not adapt the length of the
screw to the new power supply unit. As a result, the screw rose up the inside the power supply, where the
distances to a part under voltage became too small. The surge test ended with the flash over at 2000V to the
frame and the power supply was damaged.

Modification and results after troubleshooting:

Burst: Network inlet spatially shifted.

No interference up to 2500V

Surge: Mounting bolt shortened.

No arcing at 4000V L-PE

Figure 8 : Design after troubleshooting

-8-
4 Design according to the EMC requirements
Conducted RF disturbances such as burst pulses are generated during switching operations. These are cou-
pled to the signal and mains lines mostly in the common mode. Therefore, the supply lines are predestined to
spread the disturbances inside the device. To remove the disturbances, a bypass capacitor must be con-
nected near the rectifier. Otherwise, the disturbance distributes itself over all lines, which forms a coupling
capacity with their surface against earth. The immunity is substantially increased by the following this meas-
ures:

Tips
• Star shaped distribution of the supply to the individual components.
• Capacitor between GND and earth near the rectifier (1...100nF).
• A bypass capacitor at every integrated circuit chip.
• Bypass capacitors for external signal lines to GND.
• Screened control and data cables (screen connects to the frame).
• GND branch line for oscillators and pulling capacitor to the processor GND.

Figure 9: EMC layout

-9-
5 Conducted Emissions

5.1 Definition, Origin and Spreading

Radio interferences are all unwanted emissions in the frequency range between 9kHz to over 400GHz. One
differentiates between conducted emission and radiated emission.
The elimination of radio interference means to reduce the disturbances under the prescribed limit values. De-
pending on the application, different standards are used.
Interferences are generated by spark gaps of commutator motors and from fast voltage changes in electronic
circuits (phase control rectifiers and digital circuits), as well as from harmonics of oscillators. The high clock
rate of electronic devices produce fast slew rates, which produce harmonics in the FM and television band.
In all electronic circuits it is possible that completely unnoticed and unintentional oscillations and resonance’s
can arise which generates radio interference. Normally stable circuits can unintentionally be made to oscillate
during a layout modification.
The interfering RF spreads over all lines as conducted disturbance. Sometimes the disturbance is radiating
and disturbs the radio broadcast. Devices, with only a mains input, can spread the RF over this line and dis-
turb other devices. Therefore a disturbance is possible via the mains even in equipment with a shielded
housing.
The measurement of conducted emission is made with two different detectors. These are quasi peak (QP)
and average (AVG). Each detector has individual limits.
Narrowband disturbers such as quartz oscillator frequencies give the same results with both detectors. How-
ever, wide-band disturbers, such as phase controlled devices produce clearly smaller values when evaluated
using the AVG method. Therefore, the AVG limit curves are usually for 10dB below the QP curves.
If the QP measurement result is always below the AVG limit, the AVG measurement is not necessary. The
AVG measurement is always less than or equal to the QP measurement.
The conducted emission is measured as voltage interference in the frequency range between 150kHz and
30MHz. The supply lines (AC and DC) are measured with an artificial network and the control or data lines
with a probe. The radiated emission above 30MHz is measured in an absorber test chamber or in the field.

- 10 -
5.2 Leakage current

For filtering the radio interference, X- and Y- capacitors as well as

inductances are usually used. By using Y-capacitors a leakage
current results, which is specified depending upon device class. If
no leakage current is specified, then 0.75mA are to be assumed as
the limit value. In addition to the leakage current of the Y- capaci-
tors, the specific device leakage current must also be added.

Figure 10a: Example of EMI suppression with X and Y capacitors

One Y- capacitor Two Y- capacitors with double the leakage current

Figure 10b: Setup for measuring the leakage current

Value Y capacitor 1 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF

1 Y-Capacitor [mA] 0.072 0.159 0.238 0.340 0.491 0.723
2 Y-Capacitors [mA] 0.144 0.318 0.478 0.679 0.983 1.445
Table 1: Leakage current of some Y capacitors (V=230V, 50Hz)

Proposal for application of noise filter elements

• Reduce the disturbances at their source. A phase control can also disturb an internal
microprocessor.
• Use filters in metal housings, where a transition to a screened system exists.
• In a nonprofessional mind, you can think of RF as nebulous noise. A filter can be by-
passed by the " fog ", if the device shielding is missing.
• Always make sure, that the length of the feed line of the filter capacitors to earth is as
short as possible. Each inductance in these connections reduces the filter effect.
• If a line filter with an inductance within the range of 2x10mH does not show any effect,
something is wrong. Either the filter is by-passed on other lines or the ferrite of the toroi-
dal core is saturated by asymmetrical impulses.
• Ferrite toroidal cores can be saturated easily. Large asymmetrical impulses such as those
in phase control circuits can saturate current-compensated inductances. Use iron powder
cores and avoid ferrite cores.

- 11 -
5.3 Process of elimination of radio interference
Generally, we propose that you start EMC measurement first with the conducted emission and then continue
with the immunity check. The reasons are:

- The measurement of emissions does not destroy the device under test.
- Modifications for filtering of the radio interference also improve immunity.
- Measuring emissions results also gives information about the immunity behavior.

1. Start with the measurement of the spectrum in the original status, To get a rapid overview
to estimate the amount of filter modification required.

2. Eliminate the interference with X-capacitors parallel to the line. X-capacitors have their main
Rise the value of capacitance up to approx. 0.47µF. effect in the lower frequency
range to approx. 1MHz.

3. Y-capacitors Y- capacitors to work over

If the result with x capacitors is insufficient, continue with Y- the complete frequency
capacitors to reduce the asymmetrical part. The value can be in- range. Two capacitors with
creased up to the permissible leakage current. 2.2 nF get better results than
a single 4.7nF capacitor. The
reason is that smaller self-
inductance is obtained from
two series elements.

4. Use of inductances, which must be placed mostly in series with the

mains. The reason is that the mains impedance is lower.

5. If this is not successful, please examine whether the filter ele-

ments are bypassed by cross coupling.

6. If the limits are only exceeded on the higher frequency range, the Lines that radiate RF,
design must be examined for radiation. Using RF inductors with slots, openings.
nickel zinc ferrite material can be a solution for the problem.

7. If the conducted emission to 30MHz is within the limits, you can

continue with measurements above 30MHz in the radiated fre-
quency range.

8. As a final check we propose testing another device from the same Modifications in the layout
production lot so you are sure that the manufacturing process is have also an influence on the
correct. EMC behavior.

- 12 -
5.4 Systematic overview of radio interference and their remedy

5.4.1 Interference voltage ( conducted emission )

Symmetrical interference Frequency range typical < 1MHz

Phase controlled

Remedy : X- capacitors,
Series inductance with iron powder core

Figure 11

Asymmetrical interference Frequency > 1MHz

Static frequency oscillators, switch power packs,
quartz oscillators

Remedy : Y-capacitors,
Inductance’s < 1MHz current compensated
inductances with core Mg-Zn
Figure 12
> 1MHz Ni-Zn core single layer winded

5.4.2 Radiated Emission

Predominantly asymmetrical type

Interference voltage on lines to or from the device
- Mains and signal lines act as antennas
- Radiating ( Device size determines the wavelength )

Remedy: • Y-capacitors,
• current compensated inductances Ni-Zn core single layer wound
• Screening (shielding) of the noise source
• Proper grounding system
• Cable layout
• All components connected to metal and grounds must be contacted with large surfaces.
.

- 13 -
5.5 Example : Effect of filter elements
As an example, we have a control device working with its maximum load to show the effect of the noise filter.
(See Figures 13...15)

Figure 13 : Original measurement

Without filtering

The interference exceeds the limit without noise

filter elements at 12dBmV.
Measurement QP on L and N.

In the drawing the results for L and N are dis-

played. The measurement on the line L has the
highest interference.

Figure 14 : Filtering with an X2 capacitor

X2-capacitor, 0.22µF parallel to the mains.

The limits are exceeded by 5 dBµV

Measurement QP phase L
Increasing of the value of the x capacitor beyond
0.22µF is insignificant.

Figure 15 : Filtering with a noise filter

Line filter model 1A-P (Meteolabor).

The limit values QP and AVG are 6 dBµV higher
than the interference.

The filter with the combination of the X- and Y

capacitors, as well as inductors reduces the
internal interference below the class B limits.

- 14 -
5.6 Leakage of noise over the GND Layer
The ground layers must be designed according the following rule: Areas with RF noise sources must be
separated with " bubbles " (blank areas). Disturbances are then grounded directly and this keeps the
other areas calm. (See fig. 16).
The ground area around the oscillator area near the processor is designed as a bubble. The load capacitance
of the oscillator is directly connected to the GND pin of the processor. Thus the quartz oscillations are not
spread unnecessarily in the circuit.
The ground path from the ground layer to earth must be as short as possible. The individual ground areas
conduct directly to the ground capacitor.

Figure 16: Reduction of noise via the GND Layer

- 15 -
Example : Interference of quartz oscillators

In this example, the AVERAGE measurement shows the disturbances are at 18 and 22 MHz (fig. 17). The
form of the disturbance suggests clock frequencies of a microprocessor. The disturbances can be eliminated
neither with X nor Y capacitors. During the investigation of the boards we recognized, that the GND line of the
load capacitances of the oscillator, distributes the disturbances in a star shape on the whole printed circuit
board. A modification of the printed circuit board with the connection from the GND of the load capacitances to
the microprocessor GND brought an improvement of the measuring results to around 8 dBµV. After this modi-
fication, the emissions meet the limits without application of further filter elements. (See figure 18)

Figure 17 : Interferences at 18 and 22 MHz

The GND load capacitance spreads the dis-

turbances directly over the whole printed cir-
cuit board.

Figure 18 : Measurement after modification

Filtering of the quartz resonant circuit by

bonding the load capacitances GND accord-
ing the recommendation in figure 16.

When the correct design is used, the emission

drops 4dBµV below the limit.

6 Plugs and cables

- 16 -
Plugs and cables are used to connect the devices to external devices and sensors. They have to pass the
signals without additional noise. EMC tests have shown that the type cables and plugs can have an influence
on the immunity performance of the product. Investigations of different applications indicate that immunity
results can vary by a factor of 2 to 3 times depending upon the types of plugs and cables used in the product.
A large number of plugs and cables on available on the market and they have a lot of different characteristics.
Often the manufacturers have an economical standard design and an exclusive product line with increased
specifications like military versions or similar types. Often a special EMC set can be ordered for a better
shielding.

Advice on choosing Plugs

• Install the plug housing with a low ohmic contact to the front plate or housing.
• If the plug is soldered on the printed circuit board, make sure that the disturbances do not
arrive via the screen inside to the device. They must be shorted to the front plate immedi-
ately.
• Grounding connections with " green yellow " wires satisfy most of the electrical safety
requirement in the low frequency 60Hz area. (U = L di/dt)
• Use plugs that have a conductive area for the cable screen to the plug around the signal
conductors.

When using plugs, it is important that interferences are shorted out over the screen directly to the front plate
or housing. Pay special attention to a conductive laminar connection to the front plate. Using screened cables,
the transition of the cable screen to the plug is very important. (Figure 19).

Figure 19 Connection Screen - connector a) poor, b) correct

- 17 -
6.1 Example : Sub D Connector with screened cable

A. Compound Connector sealing

Description:
The helical screen is soldered over a wired cable connection to the
plug housing. In this area the cables are not shielded. A large range of
quality exists among various connector manufacturers.

Immunity:
Coupling of the cable jacket current to the signal is possible. To avoid
this, filtering at the device input is mandatory.

Figure 20 :
Cheap cable screened

B. Plastic connector with metalized surface

Description:
The screen contacts the conducting surface. Depending on the design,
a defined contact resistance to the housing over the cable pull relief
can take place. The signal cables are shielded at every position.

Immunity:
The connection from the housing to the plug is not well defined. Con-
nections with plastic can flow with the time. The quality of the connec-
tion from the screen to the plug has large variations. The quality of
such a screen connection can also change with time. Figure 21: Plastic connector
with metalized surface.

C. Connector with metal case

Description:
The cable screen is connected with good contact and is screwed into
the housing. The signal cables are always in the shielded area. A leak-
age current in the range of 100A is shunted via a defined path to the
plug housing.

Immunity:
The design of this shielding method provides good results. This design
is preferred. The use of plug with metal housings and screened cables
is a simple method for producing a good immunity result especially
where a modification of the equipment is not possible. Figure 22 :
Connector with metal
for highest performance

Comparative immunity tests with burst pulses and the capacitive coupling clamp between cables of the type A
and C above result in salient differences. A type A cable can cause disturbances at 800V, whereby the same
device with a type C cable shows no interference to over 2000V.

- 18 -
6.2 Screened Cables
There is a multiplicity of screened cables available on the market. There are closed, helicoiled, braided, dou-
ble braided and isolated etc. The following figure 21 shows some examples of screened cables.

Figure 23 Example of screened cables

Most screened cables consist of a braid screen. A criterion used for evaluation of the screen is the amount of
coverage of the screen, where bad values are 60% coverage and good values have 85 to 95% coverage.
Good coverage is achieved with as much screen coverage as possible using thin wires. Two pair twisted dou-
ble screens without isolation performs better than a cable with one screen with 95% coverage.
In special applications, a triaxial cable is used. These have the advantage that the inner coaxial cable is al-
most completely protected by the second screen. A frequent application is for computer cables used in net-
works.
Closed screens provide 100% coverage and are suitable also for use with frequencies over 100 MHz.
Helicoiled screens have an overlapping metal area, which is usually not conductive. This reduces the screen-
ing effect above 100kHz. With an additional screen layer, the shielding effect can be improved.
The cables can be connected to the reference earth either on one side or on both sides. When connected on
one side to GND, the screen attenuates the electrical fields only. Grounding a cable on both sides attenuates
both the electric and magnetic fields.
It is important that the signals are separated from the screen in triaxial cables to prevent dangerous ground
loops.
Sometimes it is necessary to experiment to find the best method for cable screen grounding. The results de-
pend upon the type of the disturbance and its spectrum, the cable length and other environmental factors as
whether on not the double grounding of the screen is favorable.

- 19 -
6.3 Choice of cables
Cable Application
Twisted cables no screen. Up to approx. 1 MHz.
Magnetic compensation with twisting. The more
turns/m the better (20...60/m).
Twisted cables with screen grounded on one end. Up to approx. 1 MHz.
Magnetic compensation can be achieved by
twisting an additional electrical screen.
Coaxial cable, or triaxial cable. Up to a couple of 100 MHz.

Figure 24: Sensitivity of some cable layouts

Figure 24 shows the influence of a low frequency (50kHz) interference. The cable is 3cm above the reference
ground. All results are related to figure 24a).

- Asymmetrical lines with screen on both side grounded 24c) are less sensitive than with one side grounded
as in 24a).
- Lines, which are grounded on one side only, are clearly more insensitive than when they are grounded on
both sides.
- The screen must not be used for the signal. Disturbances on the screen influence the signal.
- A screen is an additional interference protection for twist pair cables.
- Depending upon the application, optimal shielding must be determined experimentally.

- 20 -
7 Common interference problems
The following advice allows the engineer to solve interference problems without the use of filter elements. It is
always possible to suppress the noise with a standard filter, but not always necessary. The Burst and ESD
interference often require layout modifications. This is usually necessary if the disturbance spreads out on the
printed circuit boards and no other way to eliminate the disturbance exists.

7.1 Burst Test

• General Interference Cause: Interconnection cross over unfiltered lines.

Remedy: Separate the lines spatially or decouple the lines.
Cause: Disturbance is conducted through the plug to the printed
circuit board into the device inside.
Remedy: Plugs must be grounded at the housing.
Cause: No connection screen – housing.
Remedy: Connection screen - housings must be connected.
Cause: GND line leads cross over the screen.
Remedy: Use a single conductor for GND.
Cause: Screen is connected across a pin into the device inside
and screwed internally to the housing.
Remedy: Search for another plug that solves this problem better.

• Internal Interference Cause: Devices inside equipment cause the disturbance.

Remedy: Bypass capacitor GND to earth eventually with potential
equalization resistance (MΩ value).

7.2 ESD
• Interference with reset Cause: Voltage drops during ESD caused by the current pulse
• Tripping of encoders (some 10ns).
• Short loss of function Remedy: Bypass capacitor near the disturbed device.
RC filter for undervoltage detector.
• Loss of function Cause: Front plate radiates during the test into the device in-
side.
Remedy: Conductive connection between housings and front
plates.

• Loss of function after ESD to Cause: ESD couples over the cable connections.
external housing Remedy: Use a screened cable with the correct plug.

• LCD Interference Reason: Common lines for LCD electronics GND and the LCD
frame.
Remedy: - Connect a capacitor approx. 2.2nF between the LCD
frame and the housing.
- isolate LCD with a glass
- Use LCD with two separate lines for GND / frame

- 21 -
7.3 Surge
• Internal discharge in the Cause: Insulating distance in the device inside too small.
device Remedy: Increase the distances between the components, check
the isolation class of the components.

• Destruction of components Cause: Components are the wrong size.

Remedy: Check the dielectric strength of the components.
Coordinate the overvoltage protection between the
components and the overvoltage protection.
Look for internal resonances between filters and com-
ponents.
• Interference Cause: coupling the surge pulse.
Remedy: Separate the lines that contain the surge pulses.

7.4 Power Fail

• Loss of function Cause: Storage capacitors too small.
Remedy: Increase the capacitance of the storage capacitor
• Partial loss of function Cause: Uncoordinated behavior, data loss.
Remedy: Storage capacitor of one dc voltage is too small. Adapt
the different dc voltage for a defined " shut down ".

- 22 -